Articles in this section

See more

How to set up a new S19j Pro?

  • Created
  • Updated
Follow

Set Up a New S19j Pro

Ⅰ. Before Using

Ⅱ. S19j Pro Server Overview

Ⅲ.Setting Up the Server

Ⅳ.Configuring the Server

Ⅴ. Monitoring Your Server

Ⅵ. Administering Your Server

 

Ⅰ. Before Using

  • Inspect the new miner

1. Visually inspect the box when your miner package arrives. Look for signs of damage. If package is damaged, take photos of the package’s conditions before proceeding to open the package and inspect the miner. If miner is damaged as well, contact customer support immediately.

2. Inspect the miner for aesthetic damage. Look at the corners of the miner and check for dents and cracks. Look out for broken fan blades and cables. If you noticed a damage or defect, contact customer support immediately.

3. Assess miner’s heat sinks. View from miner’s front and rear fan to check whether there are loose heat sinks. If you found loose heat sinks, contact customer support immediately.

_____.jpg

  • Know the Precautions for Use

1) PoE is not supported.

2) Only Ethernet network connection supported via a router or switch.

3) Use the miner in an environment between 5 to 35 degree Celsius.

4) Keep the miner’s surrounding humidity below 65%

5) Keep the miner free of dust and catkins to prevent corrosion and/or heat accumulation.

6) Supported browsers: Google Chrome and Firefox.

7) Power connector and PSU cord must be plugged tightly.

 

Ⅱ. S19j Pro Server Overview

__2.jpg__3.jpg

                                           Front View                                        Back View

       

Caution:

  1. Please refer to the layout above to place your goods in usage in case of any damage.
  2. The equipment must be connected to an earthed mains socket-outlet. The socket-outlet shall be installed near the equipment and shall be easily accessible.
  3. The equipment has two power inputs, only by connecting those two power supply sockets simultaneously can the equipment run. When the equipment is powered off, be sure to power off all power inputs.
  4. DO NOT remove any screws and cables tied on the product.          
  5. DO NOT PRESS the metal button on the cover.

1.1 S19j Pro Server Components

The main components and controller front panel of S19j Pro servers are shown in the following figure:

1.jpg

2.jpg

1.2、APW12 Power supply：

3.jpg

*Note:

1.Power supply APW12 is part of S19j Pro server. For detailed parameters, please refer to the specifications below.

2.Additional two power cords are needed.

 

1.3 Specifications

　 Item Value
Product
Glance		 Version S19j Pro S19j Pro S19j Pro S19j Pro
Hashrate 104T 100T 96T 92T
Model No. 240-Cb 240-Cb 240-Cb 240-Cb
Crypto Algorithm/Currency SHA256/BTC/BCH SHA256/BTC/BCH SHA256/BTC/BCH SHA256/BTC/BCH
Hashrate, TH/s  104 + 3% 100 + 3% 96 + 3% 92 + 3%
Power on wall @25°C, Watt  3068 ± 5% 2950 ± 5% 2832 ± 5% 2714 ± 5%
Power efficiency on wall @25°C, J/TH  29.5 ± 5% 29.5 ± 5% 29.5 ± 5% 29.5 ± 5%
Psu
Standard		 Power supply AC Input voltage, Volt (1-1) 200~240 200~240 200~240 200~240
Power supply AC Input  Frequency Range, Hz  47~63 47~63 47~63 47~63
Power supply AC Input current, Amp(1-2) 20（1-3） 20（1-3） 20（1-3） 20（1-3）
Hardware
Configuration		 Networking connection mode  RJ45 Ethernet 10/100M  RJ45 Ethernet 10/100M  RJ45 Ethernet 10/100M  RJ45 Ethernet 10/100M 
Server Size (Length*Width*Height, w/o  package), mm(2-1) 400*195.5*290 400*195.5*290 400*195.5*290 400*195.5*290
Server Size (Length*Width*Height, with  package), mm 570*316*430 570*316*430 570*316*430 570*316*430
Net weight, kg(2-2) 14.6 14.6 14.6 14.6
Gross weight, kg  15.8 15.8 15.8 15.8
Environment
Requirements		 Operation temperature,°C  0~40 0~40 0~40 0~40
Storage temperature,°C  -20~70 -20~70 -20~70 -20~70
Operation humidity(non-condensing) , RH 10~90% 10~90% 10~90% 10~90%
Operation altitude, m(3-1) ≤2000 ≤2000 ≤2000 ≤2000

*NOTE:

  1. To prevent the spread of virus in the firmware, which can cause damage to the ANTMINER S19 series, the setting function of “Secure Boot” has been switched on and the “Root Authority” function has been disabled. 
  2.  If the user fails to use the product in accordance with the given instructions, specifications, and conditions provided, or change the function setting without Bitmain's prior consent, Bitmain will not be liable for any damage arising therefrom.

(1-1)  Caution: Wrong input voltage may probably cause server damaged

(1-2）Max condition: temperature 40°C, altitude 0m

(1-3)  Two AC input wires, 10A per wire

(2-1）​​​​Including PSU size

(2-2)  Including PSU weight

(3-1)  When the server is used at an altitude from 900m to 2000m, the highest operating temperature decreases by 1℃ for every increase of 300m

 

Ⅲ.Setting Up the Server

    To set up the sever

     The file IPReporter.zip is supported by Microsoft Windows only.

  1. Go to the following site: https://shop.bitmain.com/support.htm？pid=00720160906053730999PVD2K0vz0693
  2. Download the following file: IPReporter.zip.
  3. Extract the file.the default DHCP network protocol distributes IP addresses automatically.
  4. Right-click”IPReporter.exe“and run it as Administrator.
  5. Select one of the following options:

    ■ Shelf, Step, Position – suitable for farm servers to mark the location of the servers.

    ■ Default – suitable for home servers.

  6. Click “Start”._IP.gif

  7. On the controller board, click the IP Report button. Hold it down until it beeps (about 5 seconds).

    4.jpg

    The IP address will be displayed in a window on your computer screen.5.jpg

  8. In your web browser, enter the IP address provided.
  9. Proceed to login using root for both the username and password.____.gif
  10. In the Protocol section, you can assign a Static IP address (optional).
  11. Enter the IP address, Subnet mask, gateway and DNS Server.
  12. Click “Save”.6.jpg
  13. Click https://support.bitmain.com/hc/en-us/articles/360018950053 to learn more about gateway and DNS Server.

Ⅳ.Configuring the Server

Setting Up the Pool

To configure the server:

  1. click Setting marked below.7.jpg*Note:
  • Fan speed percentage can be adjusted, but we recommend to keep the default setting. The server will adjust the fan speed automatically if the fan speed percentage has yet been selected.   
  • There are two working modes of 19 series server: Normal mode and Sleep mode. The server enters the sleep mode under the condition that the control board is powered while hashboards are not powered.

      2. Configure miner’s pool settings

Click the “Miner Configuration” tab to set up the mining pools. Key in the mining pool URL and miner name (under Worker).____.gif

Then click “Save” to connect to the mining pools.

*Note: In this article, we are using Antpool. Feel free to use other mining pools.

 

Ⅴ. Monitoring Your Server

To check the operating status of your server

1. Click dashboard marked below to check the server status.8.jpg

*Note:

The S19j Pro server (92T) is with fixed frequency 485 MHz. Firmware will stop running when the Temp(Outlet) reaches to 85℃，there will be an error message “over max temp, pcb temp (real-time temp)”shown on the bottom of kernel log page. Meanwhile, the server temperature on the dashboard interface turns to abnormal and shows “Temp is too high”.

2. Monitor your server according to the descriptions in the following table:

Option

Description

Number of chips

Number of chips detected in the chain.

Frequency

ASIC frequency setting.

Real Hashrate

Real-time Hashrate of each hash board (GH/s).

Inlet Temp

Temperature of the inlet (°C).

Outlet Temp

Temperature of the outlet (°C).

Chip state

One of the following statuses will appear:

●      The Green Icon - indicates normal

●      The Red Icon- indicates abnormal

 

Ⅵ. Administering Your Server

6.1 Checking Your Firmware Version

To check your firmware version:

  1. Enter the backstage of your server, find the firmware version on the bottom.
  2. Firmware Version displays the date of the firmware your server uses. In the examples below, the server is using firmware version9.jpg

6.2 Checking Your Firmware Version

Make sure that the S19j Pro server remains powered during the upgrade process. If power fails before the upgrade is completed, you will need to return it to Bitmain for repair.

To upgrade the server’s firmware:

  1. In System, click“ Firmware Upgrade”.10.jpg
  2. For Keep Settings:

    ■ Select “keep settings” to keep your current settings (default).

    ■ Unselect “keep settings” to reset the server to default settings.

  3. Click the mceclip1.pngbutton and navigate to the upgrade file. Select the upgrade file, then click “Update”.

  4. When the upgrade is completed, restart the server and it will turn to the setting page.mceclip0.png

6.3 Modifying Your Password

To change your login password:

  1. In System, click the “Password”
  2. Set your new password, then click “Save”.mceclip2.png

6.4 Restoring Initial Settings 

To restore your initial settings

  1. Turn on the server and let it run for 5 minutes.
  2. On the controller front panel, press and hold the Reset button for 10 seconds.

*Note:

Resetting your server will reboot it and restore its default settings. The red LED will automatically

flash once every 15 seconds if the reset is operated successfully.  

 

 

Should you have any inquiries, feel free to contact us for assistance.

    Contact us >

 

Comments

0 comments

Please sign in to leave a comment.