S9 not mine

Good afternoon, I have 1 Antminer S9 with 1 hansboard connected, which does not mine when booting. In the Kennel Log it says at the end:
"ERROR: Failed to fetch url (http://10.72.3.11/mms/posttesttime.do?minertype=S9&minerID=8024c44e5740881c&testtime=25) - curl said: Timeout was reached".
 Failed: Hashrate is too low, hashrate = 4531 <10000. I need help solving, since I couldn't
get this computer started. Greetings from Venezuela.

Andres

Annexed Kernel Log

[ 0.000000] Booting Linux on physical CPU 0x0

[ 0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017

[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d

[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

[ 0.000000] Machine model: Xilinx Zynq

[ 0.000000] cma: CMA: reserved 128 MiB at 16800000

[ 0.000000] Memory policy: Data cache writealloc

[ 0.000000] On node 0 totalpages: 126976

[ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000

[ 0.000000] Normal zone: 992 pages used for memmap

[ 0.000000] Normal zone: 0 pages reserved

[ 0.000000] Normal zone: 126976 pages, LIFO batch:31

[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768

[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096

[ 0.000000] pcpu-alloc: [0] 0 [0] 1

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984

[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait

[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)

[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)

[ 0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)

[ 0.000000] Virtual kernel memory layout:

[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)

[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)

[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)

[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)

[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)

[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)

[ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB)

[ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB)

[ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB)

[ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB)

[ 0.000000] Preemptible hierarchical RCU implementation.

[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.

[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.

[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2

[ 0.000000] NR_IRQS:16 nr_irqs:16 16

[ 0.000000] ps7-slcr mapped to df802000

[ 0.000000] zynq_clock_init: clkc starts at df802100

[ 0.000000] Zynq clock init

[ 0.000013] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns

[ 0.000295] ps7-ttc #0 at df804000, irq=43

[ 0.000592] Console: colour dummy device 80x30

[ 0.000621] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)

[ 0.040198] pid_max: default: 32768 minimum: 301

[ 0.040406] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)

[ 0.040425] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)

[ 0.042496] CPU: Testing write buffer coherency: ok

[ 0.042804] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000

[ 0.042860] Setting up static identity map for 0x4c4b00 - 0x4c4b58

[ 0.043080] L310 cache controller enabled

[ 0.043098] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB

[ 0.120989] CPU1: Booted secondary processor

[ 0.210220] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001

[ 0.210348] Brought up 2 CPUs

[ 0.210368] SMP: Total of 2 processors activated.

[ 0.210376] CPU: All CPU(s) started in SVC mode.

[ 0.211033] devtmpfs: initialized

[ 0.213419] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4

[ 0.214594] regulator-dummy: no parameters

[ 0.221494] NET: Registered protocol family 16

[ 0.223764] DMA: preallocated 256 KiB pool for atomic coherent allocations

[ 0.226024] cpuidle: using governor ladder

[ 0.226037] cpuidle: using governor menu

[ 0.233405] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered

[ 0.234915] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.

[ 0.234929] hw-breakpoint: maximum watchpoint size is 4 bytes.

[ 0.235038] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000

[ 0.256636] bio: create slab <bio-0> at 0

[ 0.258011] vgaarb: loaded

[ 0.258725] SCSI subsystem initialized

[ 0.259587] usbcore: registered new interface driver usbfs

[ 0.259756] usbcore: registered new interface driver hub

[ 0.259986] usbcore: registered new device driver usb

[ 0.260652] media: Linux media interface: v0.10

[ 0.260808] Linux video capture interface: v2.00

[ 0.261193] pps_core: LinuxPPS API ver. 1 registered

[ 0.261336] PTP clock support registered

[ 0.261693] EDAC MC: Ver: 3.0.0

[ 0.262708] Advanced Linux Sound Architecture Driver Initialized.

[ 0.265408] DMA-API: preallocated 4096 debug entries

[ 0.265422] DMA-API: debugging enabled by kernel config

[ 0.265489] Switched to clocksource arm_global_timer

[ 0.285694] NET: Registered protocol family 2

[ 0.286333] TCP established hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.286390] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)

[ 0.286476] TCP: Hash tables configured (established 4096 bind 4096)

[ 0.286518] TCP: reno registered

[ 0.286535] UDP hash table entries: 256 (order: 1, 8192 bytes)

[ 0.286565] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)

[ 0.286798] NET: Registered protocol family 1

[ 0.287086] RPC: Registered named UNIX socket transport module.

[ 0.287098] RPC: Registered udp transport module.

[ 0.287106] RPC: Registered tcp transport module.

[ 0.287115] RPC: Registered tcp NFSv4.1 backchannel transport module.

[ 0.287127] PCI: CLS 0 bytes, default 64

[ 0.287550] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available

[ 0.289531] futex hash table entries: 512 (order: 3, 32768 bytes)

[ 0.291779] msgmni has been set to 967

[ 0.292544] io scheduler noop registered

[ 0.292557] io scheduler deadline registered

[ 0.292595] io scheduler cfq registered (default)

[ 0.304074] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208

[ 0.304094] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16

[ 0.427543] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps

[ 0.994815] console [ttyPS0] enabled

[ 0.999092] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000

[ 1.006704] [drm] Initialized drm 1.1.0 20060810

[ 1.023642] brd: module loaded

[ 1.032977] loop: module loaded

[ 1.042380] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k

[ 1.056097] libphy: XEMACPS mii bus: probed

[ 1.060462] ------------- phy_id = 0x3625e62

[ 1.065161] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54

[ 1.074038] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[ 1.080872] ehci-pci: EHCI PCI platform driver

[ 1.088108] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?

[ 1.094907] usbcore: registered new interface driver usb-storage

[ 1.101777] mousedev: PS/2 mouse device common for all mice

[ 1.107892] i2c /dev entries driver

[ 1.114780] zynq-edac f8006000.ps7-ddrc: ecc not enabled

[ 1.120286] cpufreq_cpu0: failed to get cpu0 regulator: -19

[ 1.126198] Xilinx Zynq CpuIdle Driver started

[ 1.131030] sdhci: Secure Digital Host Controller Interface driver

[ 1.137148] sdhci: Copyright(c) Pierre Ossman

[ 1.141463] sdhci-pltfm: SDHCI platform and OF driver helper

[ 1.148352] mmc0: no vqmmc regulator found

[ 1.152369] mmc0: no vmmc regulator found

[ 1.195511] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA

[ 1.204193] usbcore: registered new interface driver usbhid

[ 1.209703] usbhid: USB HID core driver

[ 1.214393] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda

[ 1.220687] nand: Micron MT29F2G08ABAEAWP

[ 1.224656] nand: 256MiB, SLC, page size: 2048, OOB size: 64

[ 1.230599] Bad block table found at page 131008, version 0x01

[ 1.236817] Bad block table found at page 130944, version 0x01

[ 1.242864] 3 ofpart partitions found on MTD device pl353-nand

[ 1.248631] Creating 3 MTD partitions on "pl353-nand":

[ 1.253737] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"

[ 1.261781] 0x000002000000-0x00000b000000 : "angstram-rootfs"

[ 1.269079] 0x00000b000000-0x000010000000 : "upgrade-rootfs"

[ 1.277960] TCP: cubic registered

[ 1.281198] NET: Registered protocol family 17

[ 1.285920] Registering SWP/SWPB emulation handler

[ 1.291792] regulator-dummy: disabling

[ 1.296102] UBI: attaching mtd1 to ubi0

[ 1.825233] UBI: scanning is finished

[ 1.836877] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0

[ 1.843930] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes

[ 1.850726] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048

[ 1.857403] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096

[ 1.864240] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0

[ 1.870250] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128

[ 1.877360] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1283732989

[ 1.886391] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40

[ 1.895607] UBI: background thread "ubi_bgt0d" started, PID 1080

[ 1.895613] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)

[ 1.899441] ALSA device list:

[ 1.899444] No soundcards found.

[ 1.915927] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082

[ 1.985478] UBIFS: mounted UBI device 0, volume 0, name "rootfs"

[ 1.991427] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes

[ 2.000532] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)

[ 2.010420] UBIFS: reserved for root: 0 bytes (0 KiB)

[ 2.015450] UBIFS: media format: w4/r0 (latest is w4/r0), UUID C72F8006-6DFF-46BA-BBE9-380960A89F92, small LPT model

[ 2.027013] VFS: Mounted root (ubifs filesystem) on device 0:11.

[ 2.034420] devtmpfs: mounted

[ 2.037544] Freeing unused kernel memory: 204K (c06d2000 - c0705000)

[ 2.870345] random: dd urandom read with 0 bits of entropy available

[ 3.255536]

[ 3.255536] bcm54xx_config_init

[ 3.865536]

[ 3.865536] bcm54xx_config_init

[ 6.866355] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz

[ 6.872445] xemacps e000b000.ps7-ethernet: link up (100/FULL)

[ 21.968163] In axi fpga driver!

[ 21.971229] request_mem_region OK!

[ 21.974620] AXI fpga dev virtual address is 0xdf9fc000

[ 21.979766] *base_vir_addr = 0xc51e

[ 21.994695] In fpga mem driver!

[ 21.997818] request_mem_region OK!

[ 22.001326] fpga mem virtual address is 0xe2000000

[ 22.805526]

[ 22.805526] bcm54xx_config_init

[ 23.435546]

[ 23.435546] bcm54xx_config_init

[ 26.436369] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz

[ 26.442392] xemacps e000b000.ps7-ethernet: link up (100/FULL)

This is XILINX board. Totalram: 507527168

Detect 512MB control board of XILINX

DETECT HW version=0000c51e

miner ID : 8024c44e5740881c

Miner Type = S9

AsicType = 1387

real AsicNum = 63

Find /tmp/searcherror: R:2 The last log is below:

This is XILINX board. Totalram: 507527168

Detect 512MB control board of XILINX

Find Force Freq=600 will search Freq again!

DETECT HW version=0000c51e

miner ID : 8024c44e5740881c

config file found, will disable freq setting.

Miner Type = S9

AsicType = 1387

real AsicNum = 63

use critical mode to search freq...

get PLUG ON=0x00000080

Find hashboard on Chain[7]

set_reset_allhashboard = 0x0000ffff

Check chain[7] PIC fw version=0x03

chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]

Start search freq on chain[7]...

Check chain[7] PIC fw version=0x03

get PIC voltage=6 on chain[7], value=940

set voltage=870 search freq on chain[7]

now set pic voltage=125 on chain[7]

enable_pic_dac on chain[7]

set_reset_allhashboard = 0x00000000

chain[7] temp offset record: 62,0,0,0,0,0,37,28

chain[7] temp chip I2C addr=0x98

chain[7] has no middle temp, use special fix mode.

set_reset_allhashboard = 0x0000ffff

set_reset_allhashboard = 0x00000000

CRC error counter=0

set command mode to VIL

--- check asic number

check chain[7]: asicNum = 63

After Get ASIC NUM CRC error counter=0

set_baud=0

SEARCH_FREQ_TEST_LEVEL mode set freq=650 voltage=870 on chain[7]

The min freq=650

set real timeout 56, need sleep=408576

start send works on chain[7]

get send work num :57456 on Chain[7]

wait recv nonce on chain[7]

get nonces on chain[7]

require nonce number:912

require validnonce number:57456

freq[00]=650 freq[01]=650 freq[02]=650 freq[03]=650 freq[04]=650 freq[05]=650 freq[06]=650 freq[07]=650

freq[08]=650 freq[09]=650 freq[10]=650 freq[11]=650 freq[12]=650 freq[13]=650 freq[14]=650 freq[15]=650

freq[16]=650 freq[17]=650 freq[18]=650 freq[19]=650 freq[20]=650 freq[21]=650 freq[22]=650 freq[23]=650

freq[24]=650 freq[25]=650 freq[26]=650 freq[27]=650 freq[28]=650 freq[29]=650 freq[30]=650 freq[31]=650

freq[32]=650 freq[33]=650 freq[34]=650 freq[35]=650 freq[36]=650 freq[37]=650 freq[38]=650 freq[39]=650

freq[40]=650 freq[41]=650 freq[42]=650 freq[43]=650 freq[44]=650 freq[45]=650 freq[46]=650 freq[47]=650

freq[48]=650 freq[49]=650 freq[50]=650 freq[51]=650 freq[52]=650 freq[53]=650 freq[54]=650 freq[55]=650

freq[56]=650 freq[57]=650 freq[58]=650 freq[59]=650 freq[60]=650 freq[61]=650 freq[62]=650

total valid nonce number:55642

total send work number:57456

require valid nonce number:57456

repeated_nonce_num:0

err_nonce_num:13898

last_nonce_num:8329

checkBoardState chain[7] rate=3896 bad_chip_num=10 lowest rate=4666 ret=1

After TEST CRC error counter=0

check FAN Speed: fan[4] speed=5400

check FAN Speed: fan[5] speed=5400

check FAN OK: fan num=2

set_reset_allhashboard = 0x0000ffff

set_reset_allhashboard = 0x00000000

search freq for 1 times, completed chain = 0, total chain num = 1

set_reset_allhashboard = 0x0000ffff

set_reset_allhashboard = 0x00000000

CRC error counter=0

set command mode to VIL

--- check asic number

check chain[7]: asicNum = 63

After Get ASIC NUM CRC error counter=0

set_baud=0

SEARCH_FREQ_TEST_LEVEL mode set freq=631 voltage=890 on chain[7]

The min freq=631

set real timeout 58, need sleep=423168

start send works on chain[7]

get send work num :57456 on Chain[7]

wait recv nonce on chain[7]

get nonces on chain[7]

require nonce number:912

require validnonce number:57456

freq[00]=631 freq[01]=631 freq[02]=631 freq[03]=631 freq[04]=631 freq[05]=631 freq[06]=631 freq[07]=631

freq[08]=631 freq[09]=631 freq[10]=631 freq[11]=631 freq[12]=631 freq[13]=631 freq[14]=631 freq[15]=631

freq[16]=631 freq[17]=631 freq[18]=631 freq[19]=631 freq[20]=631 freq[21]=631 freq[22]=631 freq[23]=631

freq[24]=631 freq[25]=631 freq[26]=631 freq[27]=631 freq[28]=631 freq[29]=631 freq[30]=631 freq[31]=631

freq[32]=631 freq[33]=631 freq[34]=631 freq[35]=631 freq[36]=631 freq[37]=631 freq[38]=631 freq[39]=631

freq[40]=631 freq[41]=631 freq[42]=631 freq[43]=631 freq[44]=631 freq[45]=631 freq[46]=631 freq[47]=631

freq[48]=631 freq[49]=631 freq[50]=631 freq[51]=631 freq[52]=631 freq[53]=631 freq[54]=631 freq[55]=631

freq[56]=631 freq[57]=631 freq[58]=631 freq[59]=631 freq[60]=631 freq[61]=631 freq[62]=631

total valid nonce number:57456

total send work number:57456

require valid nonce number:57456

repeated_nonce_num:0

err_nonce_num:13821

last_nonce_num:7477

checkBoardState chain[7] rate=4531 bad_chip_num=0 lowest rate=4500 ret=2

SEARCH_FREQ_TEST_LEVEL get BOARD_FREQ_OK on chain[7]

special fix hash_voltage pic value = 91 [890] of Chain[7], voladded=0

Write freq to PIC :

Freq[00]=631

Freq[01]=631 Freq[02]=631 Freq[03]=631 Freq[04]=631 Freq[05]=631 Freq[06]=631 Freq[07]=631

Freq[08]=631 Freq[09]=631 Freq[10]=631 Freq[11]=631 Freq[12]=631 Freq[13]=631 Freq[14]=631

Freq[15]=631 Freq[16]=631 Freq[17]=631 Freq[18]=631 Freq[19]=631 Freq[20]=631 Freq[21]=631

Freq[22]=631 Freq[23]=631 Freq[24]=631 Freq[25]=631 Freq[26]=631 Freq[27]=631 Freq[28]=631

Freq[29]=631 Freq[30]=631 Freq[31]=631 Freq[32]=631 Freq[33]=631 Freq[34]=631 Freq[35]=631

Freq[36]=631 Freq[37]=631 Freq[38]=631 Freq[39]=631 Freq[40]=631 Freq[41]=631 Freq[42]=631

Freq[43]=631 Freq[44]=631 Freq[45]=631 Freq[46]=631 Freq[47]=631 Freq[48]=631 Freq[49]=631

Freq[50]=631 Freq[51]=631 Freq[52]=631 Freq[53]=631 Freq[54]=631 Freq[55]=631 Freq[56]=631

Freq[57]=631 Freq[58]=631 Freq[59]=631 Freq[60]=631 Freq[61]=631 Freq[62]=631

Chain[7] bad core info:

After TEST CRC error counter=0

check FAN Speed: fan[4] speed=5400

check FAN Speed: fan[5] speed=5400

check FAN OK: fan num=2

set_reset_allhashboard = 0x0000ffff

set_reset_allhashboard = 0x00000000

search freq for 2 times, completed chain = 1, total chain num = 1

get search_end_time=22

search freq cost time: 75 s

post: http://192.168.60.104/mms/postsearchtime.do?minertype=S9&minerID=8024c44e5740881c&searchtime=75

ERROR: Failed to fetch url (http://192.168.60.104/mms/postsearchtime.do?minertype=S9&minerID=8024c44e5740881c&searchtime=75) - curl said: Timeout was reached

post: http://10.70.22.1/mms/postsearchtime.do?minertype=S9&minerID=8024c44e5740881c&searchtime=75

ERROR: Failed to fetch url (http://10.70.22.1/mms/postsearchtime.do?minertype=S9&minerID=8024c44e5740881c&searchtime=75) - curl said: Timeout was reached

post: http://10.72.3.11/mms/postsearchtime.do?minertype=S9&minerID=8024c44e5740881c&searchtime=75

ERROR: Failed to fetch url (http://10.72.3.11/mms/postsearchtime.do?minertype=S9&minerID=8024c44e5740881c&searchtime=75) - curl said: Timeout was reached

get search_start_time=112

post: http://192.168.60.104/mms/postratevol.do?minertype=S9&minerID=8024c44e5740881c&hashrate1=4531&hashrate2=0&hashrate3=0&voltage1=890&voltage2=0&voltage3=0

ERROR: Failed to fetch url (http://192.168.60.104/mms/postratevol.do?minertype=S9&minerID=8024c44e5740881c&hashrate1=4531&hashrate2=0&hashrate3=0&voltage1=890&voltage2=0&voltage3=0) - curl said: Timeout was reached

post: http://10.70.22.1/mms/postratevol.do?minertype=S9&minerID=8024c44e5740881c&hashrate1=4531&hashrate2=0&hashrate3=0&voltage1=890&voltage2=0&voltage3=0

ERROR: Failed to fetch url (http://10.70.22.1/mms/postratevol.do?minertype=S9&minerID=8024c44e5740881c&hashrate1=4531&hashrate2=0&hashrate3=0&voltage1=890&voltage2=0&voltage3=0) - curl said: Timeout was reached

post: http://10.72.3.11/mms/postratevol.do?minertype=S9&minerID=8024c44e5740881c&hashrate1=4531&hashrate2=0&hashrate3=0&voltage1=890&voltage2=0&voltage3=0

ERROR: Failed to fetch url (http://10.72.3.11/mms/postratevol.do?minertype=S9&minerID=8024c44e5740881c&hashrate1=4531&hashrate2=0&hashrate3=0&voltage1=890&voltage2=0&voltage3=0) - curl said: Timeout was reached

disable_pic_dac on chain[7]

Chain[7] read buf : 0x0 0x7d 0x0 0x47 0x0 0x47 0x4 0x47 0x7 0x47 0x0 0x47 0x3 0x47 0x3 0x47 0x3 0x47 0x3 0x47 0x3 0x47 0x3 0x47 0x1 0x47 0x1 0x47 0xf 0x47 0xf 0x47 0xf 0x47 0xf 0x47 0x5 0x47 0x9 0x47 0x23 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47 0x0 0x47

Chain[7] read badcore_buf : 0x23 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0

get search_end_time=112

test patten cost time: 25 s

post: http://192.168.60.104/mms/posttesttime.do?minertype=S9&minerID=8024c44e5740881c&testtime=25

ERROR: Failed to fetch url (http://192.168.60.104/mms/posttesttime.do?minertype=S9&minerID=8024c44e5740881c&testtime=25) - curl said: Timeout was reached

post: http://10.70.22.1/mms/posttesttime.do?minertype=S9&minerID=8024c44e5740881c&testtime=25

ERROR: Failed to fetch url (http://10.70.22.1/mms/posttesttime.do?minertype=S9&minerID=8024c44e5740881c&testtime=25) - curl said: Timeout was reached

post: http://10.72.3.11/mms/posttesttime.do?minertype=S9&minerID=8024c44e5740881c&testtime=25

ERROR: Failed to fetch url (http://10.72.3.11/mms/posttesttime.do?minertype=S9&minerID=8024c44e5740881c&testtime=25) - curl said: Timeout was reached

Luke HAO-Technical Specialist

2020年07月29日 02:35

Hello Andres

Did you check if your network in your mining farm is stable?or check of the network cable is well connected, also the network configuration is normal?

Andres Eloy Aguiar Marmol

2020年07月29日 17:23

Good afternoon. The Internet is working normal .The rest of the equipment I own is connected, and mining. The PCs are also connected, and working. Netflix also works stable. ! It's no connection problem!.Do you need to send yourself additional information?.

Thank you for the help!

Andres

S9 not mine

评论

没有找到您要找的？