s19j pro only running at 33% capacity.

评论

4 条评论

    Dear customer.
     
    From the kernel log, it shows ERROR_NET_LOST,please kindly exclude the issue by following steps:
    1. Reboot the miner
    Information for you:
    https://support.bitmain.com/hc/en-us/articles/115000211033-How-to-power-off-reboot-or-restart-the-miner
     
    2. Check your network, network interface, miner network interface, network cable and etc. please make sure it's work normally
     
    If there are still problems after the above steps, please send the latest kernel log and miner status.
    We will double-check for you.

    0
    评论操作 固定链接

    Dear customer.
     
    From the kernel log, It shows that the hash board can not be detected. please kindly exclude the issue by following steps:
    1. Check the wires for the hashboard--pull them and re-plug them again, and also you can try to change the new wires.
     
    2. Please clean up the dust.
    How To Clean and Dust The ANTIMINERS
    https://support.bitmain.com/hc/en-us/articles/115004520173-How-To-Clean-and-Dust-The-Antminers
     
    If there are still problems after the above steps, please send the latest kernel log and miner status.
    We will double-check for you.

    0
    评论操作 固定链接

    I already adjusted the cables and restarted the computer and it still gives the same error:

     

    [    0.000000] Booting Linux on physical CPU 0x0
    [    0.000000] Initializing cgroup subsys cpu
    [    0.000000] Linux version 3.8.13+ (jenkins@nomd-nomd-fwc-bj) (gcc version 4.9.4 (Linaro GCC 4.9-2017.01) ) #32 SMP Tue Mar 29 14:21:11 CST 2022
    [    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d
    [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
    [    0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone
    [    0.000000] Memory policy: ECC disabled, Data cache writeback
    [    0.000000] On node 0 totalpages: 65280
    [    0.000000] free_area_init_node: node 0, pgdat c05d9000, node_mem_map c0631000
    [    0.000000]   Normal zone: 512 pages used for memmap
    [    0.000000]   Normal zone: 0 pages reserved
    [    0.000000]   Normal zone: 64768 pages, LIFO batch:15
    [    0.000000] AM335X ES1.0 (neon )
    [    0.000000] PERCPU: Embedded 8 pages/cpu @c083e000 s9856 r8192 d14720 u32768
    [    0.000000] pcpu-alloc: s9856 r8192 d14720 u32768 alloc=8*4096
    [    0.000000] pcpu-alloc: [0] 0 
    [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64768
    [    0.000000] Kernel command line: console=ttyO0,115200n8 init=/sbin/init
    [    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
    [    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
    [    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
    [    0.000000] __ex_table already sorted, skipping sort
    [    0.000000] allocated 524288 bytes of page_cgroup
    [    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [    0.000000] Memory: 255MB = 255MB total
    [    0.000000] Memory: 245416k/245416k available, 16728k reserved, 0K highmem
    [    0.000000] Virtual kernel memory layout:
    [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    [    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    [    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
    [    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
    [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    [    0.000000]     modules : 0xbf800000 - 0xbfe00000   (   6 MB)
    [    0.000000]       .text : 0xc0008000 - 0xc053f674   (5342 kB)
    [    0.000000]       .init : 0xc0540000 - 0xc0571680   ( 198 kB)
    [    0.000000]       .data : 0xc0572000 - 0xc05d9ee0   ( 416 kB)
    [    0.000000]        .bss : 0xc05d9ee0 - 0xc0630448   ( 346 kB)
    [    0.000000] Hierarchical RCU implementation.
    [    0.000000]     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
    [    0.000000] NR_IRQS:16 nr_irqs:16 16
    [    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
    [    0.000000] Total of 128 interrupts on 1 active controller
    [    0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz
    [    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
    [    0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz
    [    0.000000] Console: colour dummy device 80x30
    [    0.000350] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968)
    [    0.015447] pid_max: default: 32768 minimum: 301
    [    0.015670] Security Framework initialized
    [    0.015762] Mount-cache hash table entries: 512
    [    0.024257] Initializing cgroup subsys cpuacct
    [    0.024289] Initializing cgroup subsys memory
    [    0.024350] Initializing cgroup subsys blkio
    [    0.024478] CPU: Testing write buffer coherency: ok
    [    0.024975] CPU0: thread -1, cpu 0, socket -1, mpidr 0
    [    0.025050] Setting up static identity map for 0x8030a500 - 0x8030a54c
    [    0.026417] Brought up 1 CPUs
    [    0.026442] SMP: Total of 1 processors activated (545.07 BogoMIPS).
    [    0.027725] devtmpfs: initialized
    [    0.091372] pinctrl core: initialized pinctrl subsystem
    [    0.091582] rstctl core: initialized rstctl subsystem
    [    0.092087] regulator-dummy: no parameters
    [    0.092594] NET: Registered protocol family 16
    [    0.093256] DMA: preallocated 256 KiB pool for atomic coherent allocations
    [    0.102671] pinctrl-single 44e10800.pinmux: prop pinctrl-0 index 0 invalid phandle
    [    0.102850] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
    [    0.103899] platform 49000000.edma: alias fck already exists
    [    0.103928] platform 49000000.edma: alias fck already exists
    [    0.103953] platform 49000000.edma: alias fck already exists
    [    0.105073] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
    [    0.105253] OMAP GPIO hardware version 0.1
    [    0.106621] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
    [    0.107925] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
    [    0.109375] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
    [    0.109894] of_get_named_gpio_flags exited with status 52
    [    0.109923] gpio-rctrl rstctl.3: loaded OK
    [    0.114795] omap-gpmc 50000000.gpmc: GPMC revision 6.0
    [    0.118049] hw-breakpoint: debug architecture 0x4 unsupported.
    [    0.119946] cpsw.0: No hwaddr in dt. Using 94:e3:6d:c8:e3:35 from efuse
    [    0.128817] bio: create slab <bio-0> at 0
    [    0.140246] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver
    [    0.140528] of_get_named_gpio_flags: can't parse gpios property
    [    0.140756] vmmcsd_fixed: 3300 mV 
    [    0.143868] SCSI subsystem initialized
    [    0.145103] omap_i2c 4819c000.i2c: bus 0 rev0.11 at 100 kHz
    [    0.145134] omap_i2c 4819c000.i2c: unable to select pin group
    [    0.145368] pps_core: LinuxPPS API ver. 1 registered
    [    0.145387] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    [    0.146977] Switching to clocksource gp_timer
    [    0.164156] NET: Registered protocol family 2
    [    0.165221] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
    [    0.165309] TCP bind hash table entries: 2048 (order: 3, 40960 bytes)
    [    0.165402] TCP: Hash tables configured (established 2048 bind 2048)
    [    0.165494] TCP: reno registered
    [    0.165519] UDP hash table entries: 256 (order: 1, 12288 bytes)
    [    0.165563] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
    [    0.165973] NET: Registered protocol family 1
    [    0.166532] RPC: Registered named UNIX socket transport module.
    [    0.166553] RPC: Registered udp transport module.
    [    0.166567] RPC: Registered tcp transport module.
    [    0.166638] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [    0.167019] Trying to unpack rootfs image as initramfs...
    [    1.064440] Freeing initrd memory: 6480K
    [    1.065166] CPU PMU: probing PMU on CPU 0
    [    1.065196] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
    [    1.065701] omap2_mbox_probe: platform not supported
    [    1.069412] VFS: Disk quotas dquot_6.5.2
    [    1.069658] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    [    1.071030] NFS: Registering the id_resolver key type
    [    1.071118] Key type id_resolver registered
    [    1.071135] Key type id_legacy registered
    [    1.071199] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
    [    1.071641] msgmni has been set to 491
    [    1.074410] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
    [    1.074435] io scheduler noop registered
    [    1.074451] io scheduler deadline registered
    [    1.074506] io scheduler cfq registered (default)
    [    1.078160] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
    [    1.080436] omap_uart 44e09000.serial: did not get pins for uart0 error: -19
    [    1.080460] of_get_named_gpio_flags: can't parse gpios property
    [    1.080873] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0
    [    1.701692] console [ttyO0] enabled
    [    1.706042] of_get_named_gpio_flags: can't parse gpios property
    [    1.706296] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89) is a OMAP UART1
    [    1.714703] of_get_named_gpio_flags: can't parse gpios property
    [    1.714916] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90) is a OMAP UART2
    [    1.723337] of_get_named_gpio_flags: can't parse gpios property
    [    1.723544] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61) is a OMAP UART4
    [    1.731914] of_get_named_gpio_flags: can't parse gpios property
    [    1.732131] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 62) is a OMAP UART5
    [    1.753982] brd: module loaded
    [    1.764228] loop: module loaded
    [    1.768312] bone-capemgr bone_capemgr.8: Failed to find baseboard eeprom node
    [    1.778417] ONFI param page 0 valid
    [    1.782099] ONFI flash detected
    [    1.785418] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xf1 (Micron MT29F1G08ABAEAWP), 128MiB, page size: 2048, OOB size: 64
    [    1.797337] omap2-nand: detected x8 NAND flash
    [    1.802002] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme
    [    1.807586] omap2-nand: using custom ecc layout
    [    1.812426] 12 ofpart partitions found on MTD device omap2-nand.0
    [    1.818821] Creating 12 MTD partitions on "omap2-nand.0":
    [    1.824494] 0x000000000000-0x000000020000 : "spl"
    [    1.831192] 0x000000020000-0x000000040000 : "spl_backup1"
    [    1.838526] 0x000000040000-0x000000060000 : "spl_backup2"
    [    1.845837] 0x000000060000-0x000000080000 : "spl_backup3"
    [    1.853154] 0x000000080000-0x000000240000 : "u-boot"
    [    1.861433] 0x000000240000-0x000000260000 : "bootenv"
    [    1.868436] 0x000000260000-0x000000280000 : "fdt"
    [    1.875047] 0x000000280000-0x000000780000 : "kernel"
    [    1.885957] 0x000000800000-0x000001c00000 : "root"
    [    1.909298] 0x000001c00000-0x000001e00000 : "config"
    [    1.917699] 0x000001e00000-0x000002000000 : "sig"
    [    1.925831] 0x000002000000-0x000008000000 : "nvdata"
    [    2.013518] OneNAND driver initializing
    [    2.019921] mousedev: PS/2 mouse device common for all mice
    [    2.027672] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0
    [    2.035184] 44e3e000.rtc: already running
    [    2.039721] i2c /dev entries driver
    [    2.044053] pps_ldisc: PPS line discipline registered
    [    2.049552] Driver for 1-wire Dallas network protocol.
    [    2.056803] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
    [    2.064370] cpuidle: using governor ladder
    [    2.068693] cpuidle: using governor menu
    [    2.073287] of_get_named_gpio_flags exited with status 6
    [    2.073306] of_get_named_gpio_flags: can't parse gpios property
    [    2.073321] of_get_named_gpio_flags: can't parse gpios property
    [    2.073356] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed
    [    2.080579] omap_hsmmc mmc.4: Failed to get rstctl; not using any
    [    2.087371] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25
    [    2.094583] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24
    [    2.101889] mmc.4 supply vmmc_aux not found, using dummy regulator
    [    2.108836] omap_hsmmc mmc.4: pins are not configured from the driver
    [    2.143894] of_get_named_gpio_flags exited with status -517
    [    2.143959] platform gpio-leds.7: Driver leds-gpio requests probe deferral
    [    2.151607] ledtrig-cpu: registered to indicate activity on CPUs
    [    2.158368] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36
    [    2.165555] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
    [    2.173642] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
    [    2.179928] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5
    [    2.187112] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6
    [    2.195428] nf_conntrack version 0.5.0 (3935 buckets, 15740 max)
    [    2.202914] ip_tables: (C) 2000-2006 Netfilter Core Team
    [    2.208691] TCP: cubic registered
    [    2.212231] Initializing XFRM netlink socket
    [    2.216864] NET: Registered protocol family 10
    [    2.222962] ip6_tables: (C) 2000-2006 Netfilter Core Team
    [    2.228914] NET: Registered protocol family 17
    [    2.233683] NET: Registered protocol family 15
    [    2.238506] Key type dns_resolver registered
    [    2.243085] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
    [    2.251164] ThumbEE CPU extension supported.
    [    2.255681] Registering SWP/SWPB emulation handler
    [    2.261785] registered taskstats version 1
    [    2.267569] of_get_named_gpio_flags exited with status -517
    [    2.267640] platform gpio-leds.7: Driver leds-gpio requests probe deferral
    [    2.324865] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6
    [    2.331276] davinci_mdio 4a101000.mdio: detected phy mask fffffffe
    [    2.346033] libphy: 4a101000.mdio: probed
    [    2.350376] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720
    [    2.360470] of_get_named_gpio_flags exited with status -517
    [    2.360536] platform gpio-leds.7: Driver leds-gpio requests probe deferral
    [    2.368030] Detected MACID = 94:e3:6d:c8:e3:35
    [    2.372715] cpsw 4a100000.ethernet: NAPI disabled
    [    2.379667] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
    [    2.388842] cpu0 supply cpu0 not found, using dummy regulator
    [    2.395330] cpufreq_cpu0: failed to scale voltage up: -22
    [    2.401150] cpufreq_cpu0: failed to scale voltage up: -22
    [    2.414871] Freeing init memory: 196K
    [    2.495692] devpts: called with bogus options
    [    2.906973] jffs2: notice: (109) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
    [    5.207574] jffs2: notice: (115) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
    [    5.622653] net eth0: initializing cpsw version 1.12 (0)
    [    5.630954] net eth0: phy found : id is : 0x7c0f1
    [    5.643278] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    [    9.778497] libphy: 4a101000.mdio:00 - Link is Up - 100/Full
    [    9.784701] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [   11.223152] register uart_trans chrdev success.
    [   11.228674] tty port open success [/dev/ttyO1]!
    [   11.233704] init sucess for tty struct (249:1)  [/dev/ttyO1]
    [   11.240099] tty port open success [/dev/ttyO2]!
    [   11.245095] init sucess for tty struct (249:2)  [/dev/ttyO2]
    [   11.251455] tty port open success [/dev/ttyO4]!
    [   11.256470] init sucess for tty struct (249:4)  [/dev/ttyO4]
    [   11.264194] tty port open success [/dev/ttyO5]!
    [   11.270601] init sucess for tty struct (249:5)  [/dev/ttyO5]
    [   27.224692] uart trans dev open.
    [   27.228375] uart_buf virt addr = 0xccdc0000
    [   27.232965] uart_buf phys addr = 0x8cdc0000
    [   27.237493] uart_buf pfn       = 0x0008cdc0
    [   27.243589] uart trans stop send work timer.
    [   27.248579] uart trans set chain exist bits:0x7.
    [   27.258603] uart trans set work queue count 768.
    [   73.952469] uart set baud to: 4098
    [   73.956847] uart set baud to: 4098
    [   73.960822] uart set baud to: 4098
    [  156.721957] uart set baud to: 4109
    [  201.913019] uart trans start send work timer.


    ===========================================Miner log===========================================
    2000-01-01 00:00:09 Open miner sn file /config/sn error
    2000-01-01 00:00:09 Miner compile time: Tue Mar 29 14:31:43 CST 2022 type: Antminer BHB42XXX sn :
    2000-01-01 00:00:10 This is fix-freq version
    2000-01-01 00:00:10 Miner compile time: Tue Mar 29 14:31:43 CST 2022 type: Antminer BHB42XXX
    2000-01-01 00:00:10 commit version: 1956e61 2022-03-29 13:26:30, build by: jenkins 2022-03-29 14:56:34
    2000-01-01 00:00:10 opt_multi_version     = 1
    2000-01-01 00:00:10 opt_bitmain_ab        = 1
    2000-01-01 00:00:10 mid_auto_gen          = 1
    2000-01-01 00:00:10 opt_bitmain_work_mode = 0
    2000-01-01 00:00:10 port 51 already exported
    2000-01-01 00:00:10 port 49 already exported
    2000-01-01 00:00:10 port 48 already exported
    2000-01-01 00:00:10 port 60 already exported
    2000-01-01 00:00:10 port 47 already exported
    2000-01-01 00:00:10 port 27 already exported
    2000-01-01 00:00:10 port 44 already exported
    2000-01-01 00:00:10 port 22 already exported
    2000-01-01 00:00:10 no board pluged in socket 44
    2000-01-01 00:00:10 port 23 already exported
    2000-01-01 00:00:10 port 45 already exported
    2000-01-01 00:00:10 port 46 already exported
    2000-01-01 00:00:10 port 26 already exported
    2000-01-01 00:00:10 Note: front fan is power on!
    2000-01-01 00:00:10 Note: rear fan is power on!
    2000-01-01 00:00:10 start the http log.
    2000-01-01 00:00:10 httpListenThread start ret=0
    2000-01-01 00:00:10 start listen on 6060 ...
    2000-01-01 00:00:15 ==========================capability start==========================
    2000-01-01 00:00:15 board num = 3
    2000-01-01 00:00:15 board id = 0, chain num = 1
    2000-01-01 00:00:15     chain id = 0
    2000-01-01 00:00:15 board id = 1, chain num = 1
    2000-01-01 00:00:15     chain id = 1
    2000-01-01 00:00:15 board id = 2, chain num = 1
    2000-01-01 00:00:15     chain id = 2
    2000-01-01 00:00:15 ==========================capability end============================
    2000-01-01 00:00:15 chain num = 3
    2000-01-01 00:00:15 skip loading levels for now
    2000-01-01 00:00:16 load chain 0 eeprom data
    2000-01-01 00:00:16 bad_asic_crc = 4,buf[SWEEP_INFO_CRC_OFFSET] = 214
    2000-01-01 00:00:16 EEPROM error: CRC 3ND REGION
    2000-01-01 00:00:17 load chain 1 eeprom data
    2000-01-01 00:00:17 bad_asic_crc = 4,buf[SWEEP_INFO_CRC_OFFSET] = 214
    2000-01-01 00:00:17 EEPROM error: CRC 3ND REGION
    2000-01-01 00:00:17 load chain 2 eeprom data
    2000-01-01 00:00:17 bad_asic_crc = 4,buf[SWEEP_INFO_CRC_OFFSET] = 214
    2000-01-01 00:00:17 EEPROM error: CRC 3ND REGION
    2000-01-01 00:00:17 i2c_sim_init start
    2000-01-01 00:00:17 i2c_sim_init end
    2022-05-25 17:59:08 power open power_version = 0x71
    2022-05-25 17:59:13 get power version failed
    2022-05-25 17:59:13 power is not Calibrated
    2022-05-25 17:59:14 updated miner type to: Antminer S19j Pro
    2022-05-25 17:59:14 multi machine mode
    2022-05-25 17:59:14 load machine BHB42601 conf
    2022-05-25 17:59:14 machine : BHB42601 
    2022-05-25 17:59:14 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
    2022-05-25 17:59:14 fan_eft : 0  fan_pwm : 100
    2022-05-25 17:59:14 create thread get_nonce_and_register_thread
    2022-05-25 17:59:14 fixed working voltage = 1360
    2022-05-25 17:59:14 Chain [0] PCB Version: 0x0130
    2022-05-25 17:59:14 Chain [0] BOM Version: 0x0010
    2022-05-25 17:59:14 Chain [1] PCB Version: 0x0130
    2022-05-25 17:59:14 Chain [1] BOM Version: 0x0010
    2022-05-25 17:59:14 Chain [2] PCB Version: 0x0130
    2022-05-25 17:59:14 Chain [2] BOM Version: 0x0010
    2022-05-25 17:59:14 Fan check passed.
    2022-05-25 17:59:14 uart_trans addr:0xb42df000.
    2022-05-25 17:59:15 chain[0] PIC jump to app
    2022-05-25 17:59:17 Check chain[0] PIC fw version=0x89
    2022-05-25 17:59:18 chain[1] PIC jump to app
    2022-05-25 17:59:19 Check chain[1] PIC fw version=0x89
    2022-05-25 17:59:20 chain[2] PIC jump to app
    2022-05-25 17:59:22 Check chain[2] PIC fw version=0x89
    2022-05-25 17:59:22 create thread pic_heart_beat_thread
    2022-05-25 17:59:22 max sensor num = 4
    2022-05-25 17:59:22 STATUS_INITED: soc init done!
    2022-05-25 17:59:22 temperature_monitor_thread start...
    2022-05-25 17:59:25 start to init...
    2022-05-25 17:59:26 power type version: 0x0071
    2022-05-25 17:59:26 Enter sleep to make sure power release finish.
    2022-05-25 17:59:57 Slept 30 seconds, diff = 0.
    2022-05-25 17:59:57 set_voltage_by_steps to 1500.
    2022-05-25 17:59:59 chain avg vol rise to 15.12
    2022-05-25 18:00:01 start up min temp by 75a = 11
    2022-05-25 18:00:11 Chain[0]: find 0 asic, times 0
    2022-05-25 18:00:22 Chain[0]: find 0 asic, times 1
    2022-05-25 18:00:33 Chain[0]: find 0 asic, times 2
    2022-05-25 18:00:34 Chain 0 only find 0 asic, will power off hash board 0
    2022-05-25 18:00:34 chain avg vol rise to 22.68
    2022-05-25 18:00:35 chain avg vol drop to 15.11
    2022-05-25 18:00:44 Chain[1]: find 126 asic, times 0
    2022-05-25 18:00:54 Chain[2]: find 0 asic, times 0
    2022-05-25 18:01:05 Chain[2]: find 0 asic, times 1
    2022-05-25 18:01:16 Chain[2]: find 0 asic, times 2
    2022-05-25 18:01:17 Chain 2 only find 0 asic, will power off hash board 2
    2022-05-25 18:01:22 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
    2022-05-25 18:01:24 min freq in eeprom = 545
    2022-05-25 18:01:24 fixed frequency is 545
    2022-05-25 18:01:24 Bring up temperature is 12
    2022-05-25 18:01:24 set UART baud to 3000000
    2022-05-25 18:01:24 create thread check_miner_status_thread
    2022-05-25 18:01:24 create thread check_system_work_thread
    2022-05-25 18:01:24 set_voltage_by_steps to 1450.
    2022-05-25 18:01:26 fixed step freq_start = 50, freq_end = 545, freq_step = 6.25
    2022-05-25 18:01:26 chain = 1 set freq to 56.25
    2022-05-25 18:01:27 chain = 1 set freq to 62.50
    2022-05-25 18:01:27 chain = 1 set freq to 68.75
    2022-05-25 18:01:27 chain = 1 set freq to 75.00
    2022-05-25 18:01:28 chain = 1 set freq to 81.25
    2022-05-25 18:01:28 chain = 1 set freq to 87.50
    2022-05-25 18:01:28 chain = 1 set freq to 93.75
    2022-05-25 18:01:28 chain = 1 set freq to 100.00
    2022-05-25 18:01:29 chain = 1 set freq to 106.25
    2022-05-25 18:01:29 chain = 1 set freq to 112.50
    2022-05-25 18:01:29 chain = 1 set freq to 118.75
    2022-05-25 18:01:30 chain = 1 set freq to 125.00
    2022-05-25 18:01:30 chain = 1 set freq to 131.25
    2022-05-25 18:01:30 chain = 1 set freq to 137.50
    2022-05-25 18:01:31 chain = 1 set freq to 143.75
    2022-05-25 18:01:31 chain = 1 set freq to 150.00
    2022-05-25 18:01:31 chain = 1 set freq to 156.25
    2022-05-25 18:01:32 chain = 1 set freq to 162.50
    2022-05-25 18:01:32 chain = 1 set freq to 168.75
    2022-05-25 18:01:32 chain = 1 set freq to 175.00
    2022-05-25 18:01:32 chain = 1 set freq to 181.25
    2022-05-25 18:01:33 chain = 1 set freq to 187.50
    2022-05-25 18:01:33 chain = 1 set freq to 193.75
    2022-05-25 18:01:33 chain = 1 set freq to 200.00
    2022-05-25 18:01:34 chain = 1 set freq to 206.25
    2022-05-25 18:01:34 chain = 1 set freq to 212.50
    2022-05-25 18:01:34 chain = 1 set freq to 218.75
    2022-05-25 18:01:35 chain = 1 set freq to 225.00
    2022-05-25 18:01:35 chain = 1 set freq to 231.25
    2022-05-25 18:01:35 chain = 1 set freq to 237.50
    2022-05-25 18:01:35 chain = 1 set freq to 243.75
    2022-05-25 18:01:36 chain = 1 set freq to 250.00
    2022-05-25 18:01:36 chain = 1 set freq to 256.25
    2022-05-25 18:01:36 chain = 1 set freq to 262.50
    2022-05-25 18:01:37 chain = 1 set freq to 268.75
    2022-05-25 18:01:37 chain = 1 set freq to 275.00
    2022-05-25 18:01:37 chain = 1 set freq to 281.25
    2022-05-25 18:01:38 chain = 1 set freq to 287.50
    2022-05-25 18:01:38 chain = 1 set freq to 293.75
    2022-05-25 18:01:38 chain = 1 set freq to 300.00
    2022-05-25 18:01:38 chain = 1 set freq to 306.25
    2022-05-25 18:01:39 chain = 1 set freq to 312.50
    2022-05-25 18:01:39 chain = 1 set freq to 318.75
    2022-05-25 18:01:39 chain = 1 set freq to 325.00
    2022-05-25 18:01:40 chain = 1 set freq to 331.25
    2022-05-25 18:01:40 chain = 1 set freq to 337.50
    2022-05-25 18:01:40 chain = 1 set freq to 343.75
    2022-05-25 18:01:41 chain = 1 set freq to 350.00
    2022-05-25 18:01:41 chain = 1 set freq to 356.25
    2022-05-25 18:01:41 chain = 1 set freq to 362.50
    2022-05-25 18:01:41 chain = 1 set freq to 368.75
    2022-05-25 18:01:42 chain = 1 set freq to 375.00
    2022-05-25 18:01:42 chain = 1 set freq to 381.25
    2022-05-25 18:01:42 chain = 1 set freq to 387.50
    2022-05-25 18:01:43 chain = 1 set freq to 393.75
    2022-05-25 18:01:43 chain = 1 set freq to 400.00
    2022-05-25 18:01:43 chain = 1 set freq to 406.25
    2022-05-25 18:01:44 chain = 1 set freq to 412.50
    2022-05-25 18:01:44 chain = 1 set freq to 418.75
    2022-05-25 18:01:44 chain = 1 set freq to 425.00
    2022-05-25 18:01:44 chain = 1 set freq to 431.25
    2022-05-25 18:01:45 chain = 1 set freq to 437.50
    2022-05-25 18:01:45 chain = 1 set freq to 443.75
    2022-05-25 18:01:45 chain = 1 set freq to 450.00
    2022-05-25 18:01:46 chain = 1 set freq to 456.25
    2022-05-25 18:01:46 chain = 1 set freq to 462.50
    2022-05-25 18:01:46 chain = 1 set freq to 468.75
    2022-05-25 18:01:47 chain = 1 set freq to 475.00
    2022-05-25 18:01:47 chain = 1 set freq to 481.25
    2022-05-25 18:01:47 chain = 1 set freq to 487.50
    2022-05-25 18:01:48 chain = 1 set freq to 493.75
    2022-05-25 18:01:48 chain = 1 set freq to 500.00
    2022-05-25 18:01:48 chain = 1 set freq to 506.25
    2022-05-25 18:01:48 chain = 1 set freq to 512.50
    2022-05-25 18:01:49 chain = 1 set freq to 518.75
    2022-05-25 18:01:49 chain = 1 set freq to 525.00
    2022-05-25 18:01:49 chain = 1 set freq to 531.25
    2022-05-25 18:01:50 chain = 1 set freq to 537.50
    2022-05-25 18:01:50 chain = 1 set freq to 543.75
    2022-05-25 18:01:50 chain = 1 set freq to 545.00
    2022-05-25 18:01:51 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
    2022-05-25 18:01:51 start do_core_reset
    2022-05-25 18:01:57 end do_core_reset
    2022-05-25 18:02:07 set_voltage_by_steps to 1397.
    2022-05-25 18:02:09 Init done!
    2022-05-25 18:02:09 STATUS_OKAY
    2022-05-25 18:02:09 start the cached job
    2022-05-25 18:02:09 Version num 65536
    2022-05-25 18:02:09 Mask num 0x1fffe000
    2022-05-25 18:02:09 opt_multi_version = 65536, interval timeout = 2837042
    2022-05-25 18:02:09 freq = 545, percent = 90, hcn = 4809, timeout = 2837042
    2022-05-25 18:02:09 set_start_time_point total_tv_start_sys=202 total_tv_end_sys=203
    2022-05-25 18:02:09 set_voltage_by_steps to 1425.
    2022-05-25 18:02:57 set_voltage_by_steps to 1415.
    2022-05-25 18:03:30 set_voltage_by_steps to 1405.
    2022-05-25 18:05:16 set_voltage_by_steps to 1395.

    0
    评论操作 固定链接

    We are sorry that your miner is defective , please unplug then reboot it again, if it still can not work please refer to this link to prepare to ship the miner or part to us :https://service.bitmain.com/support/guide 

     

    For after-sales policy, you can refer to this link

    https://service.bitmain.com/support/terms

    Please check this link to create a repair ticket, please always click " apply for repair " to send the defective unit/part to us to have a repair.

    How to create/revise a repair ticket

     

    Please send the defective miner to our official repair site(HK or US site),  the address is as following link: https://support.bitmain.com/hc/en-us/articles/220138027-Global-repair-site-delivery-addresses

     

    Please let us know if you have any problems. Thanks.

     

    Best regards

    Nick

    BITMAIN

    0
    评论操作 固定链接

请先登录再写评论。