S19J Pro Low Hashrate and "reg crc error"

S19J Pro

This is the first time I've set up this specific device, and I can't get it working (have S9 and S11 that work fine).

I can't figure out if this is a issue with the PSU or with my electric output. Please note I ran for 30 minutes to get full log output. I've also reset factory settings and installed the firmware from the site just to be sure. At a loss. I've tested at two different locations just in case the power draw was bad at one. Full log attached.

• No "red light" error on the unit.
• Realtime Hashrate: Abnormal
• Network Status: Normal
• Fan Speed: Normal
• Miner Temp: Normal
• Log is showing "!!! reg crc error" multiple times
• Hashboard 2 and 3 never seem to get above 0 actual.
• Everything shows normal as far as chipset.
• Avg total hashrate about 100 GH/s

Feels like a power issue.

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.8.13+ (jenkins@nomd-nomd-fwc-bj) (gcc version 4.9.4 (Linaro GCC 4.9-2017.01) ) #27 SMP Thu Jun 10 12:15:30 CST 2021
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] On node 0 totalpages: 65280
[    0.000000] free_area_init_node: node 0, pgdat c05d9000, node_mem_map c0631000
[    0.000000]   Normal zone: 512 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 64768 pages, LIFO batch:15
[    0.000000] AM335X ES1.0 (neon )
[    0.000000] PERCPU: Embedded 8 pages/cpu @c083e000 s9856 r8192 d14720 u32768
[    0.000000] pcpu-alloc: s9856 r8192 d14720 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64768
[    0.000000] Kernel command line: console=ttyO0,115200n8 init=/sbin/init
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] allocated 524288 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 255MB = 255MB total
[    0.000000] Memory: 245444k/245444k available, 16700k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf800000 - 0xbfe00000   (   6 MB)
[    0.000000]       .text : 0xc0008000 - 0xc053f674   (5342 kB)
[    0.000000]       .init : 0xc0540000 - 0xc0571680   ( 198 kB)
[    0.000000]       .data : 0xc0572000 - 0xc05d9ee0   ( 416 kB)
[    0.000000]        .bss : 0xc05d9ee0 - 0xc0630448   ( 346 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[    0.000000] Total of 128 interrupts on 1 active controller
[    0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000347] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968)
[    0.015449] pid_max: default: 32768 minimum: 301
[    0.015672] Security Framework initialized
[    0.015765] Mount-cache hash table entries: 512
[    0.024264] Initializing cgroup subsys cpuacct
[    0.024294] Initializing cgroup subsys memory
[    0.024354] Initializing cgroup subsys blkio
[    0.024485] CPU: Testing write buffer coherency: ok
[    0.024990] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[    0.025066] Setting up static identity map for 0x8030a500 - 0x8030a54c
[    0.026423] Brought up 1 CPUs
[    0.026446] SMP: Total of 1 processors activated (545.07 BogoMIPS).
[    0.027719] devtmpfs: initialized
[    0.091373] pinctrl core: initialized pinctrl subsystem
[    0.091584] rstctl core: initialized rstctl subsystem
[    0.092091] regulator-dummy: no parameters
[    0.092594] NET: Registered protocol family 16
[    0.093253] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.102672] pinctrl-single 44e10800.pinmux: prop pinctrl-0 index 0 invalid phandle
[    0.102847] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
[    0.103897] platform 49000000.edma: alias fck already exists
[    0.103927] platform 49000000.edma: alias fck already exists
[    0.103952] platform 49000000.edma: alias fck already exists
[    0.105067] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
[    0.105248] OMAP GPIO hardware version 0.1
[    0.106628] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
[    0.107929] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
[    0.109385] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
[    0.109902] of_get_named_gpio_flags exited with status 52
[    0.109930] gpio-rctrl rstctl.3: loaded OK
[    0.114803] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[    0.118051] hw-breakpoint: debug architecture 0x4 unsupported.
[    0.119944] cpsw.0: No hwaddr in dt. Using c4:f3:12:6d:e7:b3 from efuse
[    0.128822] bio: create slab <bio-0> at 0
[    0.140286] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver
[    0.140577] of_get_named_gpio_flags: can't parse gpios property
[    0.140808] vmmcsd_fixed: 3300 mV 
[    0.143919] SCSI subsystem initialized
[    0.145150] omap_i2c 4819c000.i2c: bus 0 rev0.11 at 100 kHz
[    0.145182] omap_i2c 4819c000.i2c: unable to select pin group
[    0.145411] pps_core: LinuxPPS API ver. 1 registered
[    0.145427] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.147020] Switching to clocksource gp_timer
[    0.164224] NET: Registered protocol family 2
[    0.165280] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.165368] TCP bind hash table entries: 2048 (order: 3, 40960 bytes)
[    0.165461] TCP: Hash tables configured (established 2048 bind 2048)
[    0.165553] TCP: reno registered
[    0.165578] UDP hash table entries: 256 (order: 1, 12288 bytes)
[    0.165623] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
[    0.166033] NET: Registered protocol family 1
[    0.166595] RPC: Registered named UNIX socket transport module.
[    0.166673] RPC: Registered udp transport module.
[    0.166689] RPC: Registered tcp transport module.
[    0.166702] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.167080] Trying to unpack rootfs image as initramfs...
[    1.056033] Freeing initrd memory: 6452K
[    1.056668] CPU PMU: probing PMU on CPU 0
[    1.056698] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[    1.057223] omap2_mbox_probe: platform not supported
[    1.060968] VFS: Disk quotas dquot_6.5.2
[    1.061287] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.062590] NFS: Registering the id_resolver key type
[    1.062681] Key type id_resolver registered
[    1.062698] Key type id_legacy registered
[    1.062762] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.063273] msgmni has been set to 491
[    1.066029] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    1.066054] io scheduler noop registered
[    1.066070] io scheduler deadline registered
[    1.066125] io scheduler cfq registered (default)
[    1.069855] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.072129] omap_uart 44e09000.serial: did not get pins for uart0 error: -19
[    1.072153] of_get_named_gpio_flags: can't parse gpios property
[    1.072429] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0
[    1.693493] console [ttyO0] enabled
[    1.697772] of_get_named_gpio_flags: can't parse gpios property
[    1.698070] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89) is a OMAP UART1
[    1.706469] of_get_named_gpio_flags: can't parse gpios property
[    1.706688] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90) is a OMAP UART2
[    1.715078] of_get_named_gpio_flags: can't parse gpios property
[    1.715294] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61) is a OMAP UART4
[    1.723722] of_get_named_gpio_flags: can't parse gpios property
[    1.723937] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 62) is a OMAP UART5
[    1.745818] brd: module loaded
[    1.756060] loop: module loaded
[    1.760101] bone-capemgr bone_capemgr.8: Failed to find baseboard eeprom node
[    1.770198] ONFI param page 0 valid
[    1.773881] ONFI flash detected
[    1.777203] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xf1 (Micron MT29F1G08ABAEAWP), 128MiB, page size: 2048, OOB size: 64
[    1.789130] omap2-nand: detected x8 NAND flash
[    1.793798] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme
[    1.799382] omap2-nand: using custom ecc layout
[    1.804233] 12 ofpart partitions found on MTD device omap2-nand.0
[    1.810631] Creating 12 MTD partitions on "omap2-nand.0":
[    1.816312] 0x000000000000-0x000000020000 : "spl"
[    1.823020] 0x000000020000-0x000000040000 : "spl_backup1"
[    1.830325] 0x000000040000-0x000000060000 : "spl_backup2"
[    1.837684] 0x000000060000-0x000000080000 : "spl_backup3"
[    1.845005] 0x000000080000-0x000000240000 : "u-boot"
[    1.853325] 0x000000240000-0x000000260000 : "bootenv"
[    1.860320] 0x000000260000-0x000000280000 : "fdt"
[    1.866946] 0x000000280000-0x000000780000 : "kernel"
[    1.877938] 0x000000800000-0x000001c00000 : "root"
[    1.901616] 0x000001c00000-0x000001e00000 : "config"
[    1.910063] 0x000001e00000-0x000002000000 : "sig"
[    1.918234] 0x000002000000-0x000008000000 : "nvdata"
[    2.007498] OneNAND driver initializing
[    2.013908] mousedev: PS/2 mouse device common for all mice
[    2.021629] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0
[    2.029409] i2c /dev entries driver
[    2.033725] pps_ldisc: PPS line discipline registered
[    2.039211] Driver for 1-wire Dallas network protocol.
[    2.046473] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[    2.054045] cpuidle: using governor ladder
[    2.058375] cpuidle: using governor menu
[    2.062947] of_get_named_gpio_flags exited with status 6
[    2.062966] of_get_named_gpio_flags: can't parse gpios property
[    2.062981] of_get_named_gpio_flags: can't parse gpios property
[    2.063014] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed
[    2.070246] omap_hsmmc mmc.4: Failed to get rstctl; not using any
[    2.077090] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25
[    2.084303] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24
[    2.091620] mmc.4 supply vmmc_aux not found, using dummy regulator
[    2.098611] omap_hsmmc mmc.4: pins are not configured from the driver
[    2.132087] of_get_named_gpio_flags exited with status -517
[    2.132151] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    2.139928] ledtrig-cpu: registered to indicate activity on CPUs
[    2.146709] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36
[    2.153906] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[    2.161966] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[    2.168253] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5
[    2.175433] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6
[    2.183745] nf_conntrack version 0.5.0 (3935 buckets, 15740 max)
[    2.191232] ip_tables: (C) 2000-2006 Netfilter Core Team
[    2.197011] TCP: cubic registered
[    2.200557] Initializing XFRM netlink socket
[    2.205190] NET: Registered protocol family 10
[    2.211292] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    2.217250] NET: Registered protocol family 17
[    2.222026] NET: Registered protocol family 15
[    2.226874] Key type dns_resolver registered
[    2.231454] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[    2.239535] ThumbEE CPU extension supported.
[    2.244053] Registering SWP/SWPB emulation handler
[    2.250168] registered taskstats version 1
[    2.255938] of_get_named_gpio_flags exited with status -517
[    2.256008] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    2.313192] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6
[    2.319607] davinci_mdio 4a101000.mdio: detected phy mask fffffffe
[    2.334467] libphy: 4a101000.mdio: probed
[    2.338821] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720
[    2.348908] of_get_named_gpio_flags exited with status -517
[    2.348972] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[    2.356458] Detected MACID = c4:f3:12:6d:e7:b3
[    2.361141] cpsw 4a100000.ethernet: NAPI disabled
[    2.368136] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[    2.377324] cpu0 supply cpu0 not found, using dummy regulator
[    2.383810] cpufreq_cpu0: failed to scale voltage up: -22
[    2.389635] cpufreq_cpu0: failed to scale voltage up: -22
[    2.403330] Freeing init memory: 196K
[    2.484049] devpts: called with bogus options
[    2.923179] jffs2: notice: (109) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    3.849732] jffs2: Empty flash at 0x022090e0 ends at 0x02209800
[    5.248317] jffs2: notice: (115) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    5.657925] net eth0: initializing cpsw version 1.12 (0)
[    5.666245] net eth0: phy found : id is : 0x7c0f1
[    5.681597] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    5.906196] jffs2: notice: (116) check_node_data: wrong data CRC in data node at 0x02211b80: read 0x43c63ac4, calculated 0xa809add2.
[    8.743367] libphy: 4a101000.mdio:00 - Link is Up - 100/Full
[    8.749565] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   11.254353] register uart_trans chrdev success.
[   11.259847] tty port open success [/dev/ttyO1]!
[   11.264866] init sucess for tty struct (249:1)  [/dev/ttyO1]
[   11.271745] tty port open success [/dev/ttyO2]!
[   11.276766] init sucess for tty struct (249:2)  [/dev/ttyO2]
[   11.283125] tty port open success [/dev/ttyO4]!
[   11.288109] init sucess for tty struct (249:4)  [/dev/ttyO4]
[   11.294458] tty port open success [/dev/ttyO5]!
[   11.299413] init sucess for tty struct (249:5)  [/dev/ttyO5]
[   19.643046] uart trans dev open.
[   19.646757] uart_buf virt addr = 0xccd40000
[   19.651338] uart_buf phys addr = 0x8cd40000
[   19.655865] uart_buf pfn       = 0x0008cd40
[   19.661163] uart trans stop send work timer.
[   19.666096] uart trans set chain exist bits:0x7.
[   19.671173] uart trans set work queue count 768.
[   66.581401] uart set baud to: 4098
[   66.585380] uart set baud to: 4098
[   66.589630] uart set baud to: 4098
[  105.670798] uart set baud to: 4109
[  105.736122] uart set baud to: 4109
[  105.801358] uart set baud to: 4109
[  140.413736] uart trans start send work timer.
[  140.531885] hrtimer: interrupt took 47625 ns
[  201.014731] IPv6: Neighbour table overflow
[  201.020338] IPv6: Neighbour table overflow
[  201.025800] IPv6: Neighbour table overflow
[  201.031526] IPv6: Neighbour table overflow
[  201.037112] IPv6: Neighbour table overflow
[  201.042684] IPv6: Neighbour table overflow
[  201.048333] IPv6: Neighbour table overflow
[  201.053850] IPv6: Neighbour table overflow
[  201.059439] IPv6: Neighbour table overflow
[  201.065168] IPv6: Neighbour table overflow
[  237.427493] net_ratelimit: 77 callbacks suppressed
[  237.432699] IPv6: Neighbour table overflow
[  237.438294] IPv6: Neighbour table overflow
[  237.443791] IPv6: Neighbour table overflow
[  500.894167] IPv6: Neighbour table overflow
[  500.899795] IPv6: Neighbour table overflow
[  500.905310] IPv6: Neighbour table overflow
[  500.911113] IPv6: Neighbour table overflow
[  500.916707] IPv6: Neighbour table overflow
[  500.922212] IPv6: Neighbour table overflow
[  500.927798] IPv6: Neighbour table overflow
[  500.933349] IPv6: Neighbour table overflow
[  500.938891] IPv6: Neighbour table overflow
[  500.944539] IPv6: Neighbour table overflow
[  800.959638] net_ratelimit: 80 callbacks suppressed
[  800.964903] IPv6: Neighbour table overflow
[  800.970422] IPv6: Neighbour table overflow
[  800.975925] IPv6: Neighbour table overflow
[  800.981706] IPv6: Neighbour table overflow
[  800.987208] IPv6: Neighbour table overflow
[  800.992705] IPv6: Neighbour table overflow
[  800.998313] IPv6: Neighbour table overflow
[  801.003925] IPv6: Neighbour table overflow
[  801.009468] IPv6: Neighbour table overflow
[  801.015119] IPv6: Neighbour table overflow
[ 1100.948780] net_ratelimit: 74 callbacks suppressed
[ 1100.954032] IPv6: Neighbour table overflow
[ 1100.959538] IPv6: Neighbour table overflow
[ 1100.965016] IPv6: Neighbour table overflow
[ 1100.970703] IPv6: Neighbour table overflow
[ 1100.976177] IPv6: Neighbour table overflow
[ 1100.981664] IPv6: Neighbour table overflow
[ 1100.987377] IPv6: Neighbour table overflow
[ 1100.992962] IPv6: Neighbour table overflow
[ 1100.998441] IPv6: Neighbour table overflow
[ 1101.004053] IPv6: Neighbour table overflow
[ 1116.218596] net_ratelimit: 78 callbacks suppressed
[ 1116.223855] IPv6: Neighbour table overflow
[ 1116.229367] IPv6: Neighbour table overflow
[ 1116.234866] IPv6: Neighbour table overflow
[ 1117.243301] IPv6: Neighbour table overflow
[ 1117.248875] IPv6: Neighbour table overflow
[ 1117.254349] IPv6: Neighbour table overflow
[ 1119.226899] IPv6: Neighbour table overflow
[ 1119.232479] IPv6: Neighbour table overflow
[ 1119.237986] IPv6: Neighbour table overflow
[ 1119.346719] IPv6: Neighbour table overflow
[ 1401.093986] net_ratelimit: 2 callbacks suppressed
[ 1401.099113] IPv6: Neighbour table overflow
[ 1401.104574] IPv6: Neighbour table overflow
[ 1401.110045] IPv6: Neighbour table overflow
[ 1401.115689] IPv6: Neighbour table overflow
[ 1401.121143] IPv6: Neighbour table overflow
[ 1401.126622] IPv6: Neighbour table overflow
[ 1401.132205] IPv6: Neighbour table overflow
[ 1401.137730] IPv6: Neighbour table overflow
[ 1401.143175] IPv6: Neighbour table overflow
[ 1401.148824] IPv6: Neighbour table overflow


===========================================Miner log===========================================
2000-01-01 00:00:09 Miner compile time: Thu Jun 10 12:23:16 CST 2021 type: Antminer S19j Pro
2000-01-01 00:00:10 This is fix-freq version
2000-01-01 00:00:10 Miner compile time: Thu Jun 10 12:23:16 CST 2021 type: Antminer S19j Pro
2000-01-01 00:00:10 commit åversion: f579494 2021-06-09 09:22:32, build by: jenkins 2021-06-10 12:37:05
2000-01-01 00:00:10 opt_multi_version     = 1
2000-01-01 00:00:10 opt_bitmain_ab        = 1
2000-01-01 00:00:10 mid_auto_gen          = 1
2000-01-01 00:00:10 opt_bitmain_work_mode = 0
2000-01-01 00:00:10 port 51 already exported
2000-01-01 00:00:10 port 49 already exported
2000-01-01 00:00:10 port 48 already exported
2000-01-01 00:00:10 port 60 already exported
2000-01-01 00:00:10 port 47 already exported
2000-01-01 00:00:10 port 27 already exported
2000-01-01 00:00:10 port 44 already exported
2000-01-01 00:00:10 port 22 already exported
2000-01-01 00:00:10 no board pluged in socket 44
2000-01-01 00:00:10 port 23 already exported
2000-01-01 00:00:10 port 45 already exported
2000-01-01 00:00:10 port 46 already exported
2000-01-01 00:00:10 port 26 already exported
2000-01-01 00:00:10 Note: front fan is power on!
2000-01-01 00:00:10 Note: rear fan is power on!
2000-01-01 00:00:10 start the http log.
2000-01-01 00:00:10 httpListenThread start ret=0
2000-01-01 00:00:10 start listen on 6060 ...
2000-01-01 00:00:10 load machine BHB42601 conf
2000-01-01 00:00:10 machine : BHB42601 
2000-01-01 00:00:10 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2000-01-01 00:00:15 ==========================capability start==========================
2000-01-01 00:00:15 board num = 3
2000-01-01 00:00:15 board id = 0, chain num = 1
2000-01-01 00:00:15 	chain id = 0
2000-01-01 00:00:15 board id = 1, chain num = 1
2000-01-01 00:00:15 	chain id = 1
2000-01-01 00:00:15 board id = 2, chain num = 1
2000-01-01 00:00:15 	chain id = 2
2000-01-01 00:00:15 ==========================capability end============================
2000-01-01 00:00:15 chain num = 3
2000-01-01 00:00:16 load chain 0 eeprom data
2000-01-01 00:00:16 board_info_version = 4
2000-01-01 00:00:16 algorithm_and_key_version = 0x11
2000-01-01 00:00:16 board_sn = FXDZYN3BAJGBC03EL
2000-01-01 00:00:16 chip_die = ED
2000-01-01 00:00:16 chip_marking = J1CX21BE12
2000-01-01 00:00:16 chip_bin = 3
2000-01-01 00:00:16 ft_version = F1V04B2C1
2000-01-01 00:00:16 pcb_version = 0x110
2000-01-01 00:00:16 bom_version = 0x20
2000-01-01 00:00:16 asic_sensor_type = 0x0
2000-01-01 00:00:16 asic_sensor_addr[0] = 0x0
2000-01-01 00:00:16 asic_sensor_addr[1] = 0x0
2000-01-01 00:00:16 asic_sensor_addr[2] = 0x0
2000-01-01 00:00:16 asic_sensor_addr[3] = 0x0
2000-01-01 00:00:16 pic_sensor_type = 0x8b
2000-01-01 00:00:16 pic_sensor_addr = 0xf
2000-01-01 00:00:16 chip_tech = AA
2000-01-01 00:00:16 board_name = BHB42601
2000-01-01 00:00:16 factory_job = FXDZ20210723004-ZB
2000-01-01 00:00:16 board_info_crc = 0x9
2000-01-01 00:00:16 voltage = 1360
2000-01-01 00:00:16 frequency = 545
2000-01-01 00:00:16 nonce_rate = 9995
2000-01-01 00:00:16 pcb_temp_in = 32
2000-01-01 00:00:16 pcb_temp_out = 32
2000-01-01 00:00:16 test_version = 1
2000-01-01 00:00:16 test_standard = 0
2000-01-01 00:00:16 param_info_crc = 0x1d
2000-01-01 00:00:16 pt1_result = 1
2000-01-01 00:00:16 pt1_count = 1
2000-01-01 00:00:16 pt2_result = 1
2000-01-01 00:00:16 pt2_count = 1
2000-01-01 00:00:17 load chain 1 eeprom data
2000-01-01 00:00:17 board_info_version = 4
2000-01-01 00:00:17 algorithm_and_key_version = 0x11
2000-01-01 00:00:17 board_sn = FXDZYN3BAJGBC03F6
2000-01-01 00:00:17 chip_die = ED
2000-01-01 00:00:17 chip_marking = J1CX21BE12
2000-01-01 00:00:17 chip_bin = 3
2000-01-01 00:00:17 ft_version = F1V04B2C1
2000-01-01 00:00:17 pcb_version = 0x110
2000-01-01 00:00:17 bom_version = 0x20
2000-01-01 00:00:17 asic_sensor_type = 0x0
2000-01-01 00:00:17 asic_sensor_addr[0] = 0x0
2000-01-01 00:00:17 asic_sensor_addr[1] = 0x0
2000-01-01 00:00:17 asic_sensor_addr[2] = 0x0
2000-01-01 00:00:17 asic_sensor_addr[3] = 0x0
2000-01-01 00:00:17 pic_sensor_type = 0x8b
2000-01-01 00:00:17 pic_sensor_addr = 0xf
2000-01-01 00:00:17 chip_tech = AA
2000-01-01 00:00:17 board_name = BHB42601
2000-01-01 00:00:17 factory_job = FXDZ20210723004-ZB
2000-01-01 00:00:17 board_info_crc = 0x18
2000-01-01 00:00:17 voltage = 1360
2000-01-01 00:00:17 frequency = 545
2000-01-01 00:00:17 nonce_rate = 9995
2000-01-01 00:00:17 pcb_temp_in = 32
2000-01-01 00:00:17 pcb_temp_out = 32
2000-01-01 00:00:17 test_version = 1
2000-01-01 00:00:17 test_standard = 0
2000-01-01 00:00:17 param_info_crc = 0x1d
2000-01-01 00:00:17 pt1_result = 1
2000-01-01 00:00:17 pt1_count = 1
2000-01-01 00:00:17 pt2_result = 1
2000-01-01 00:00:17 pt2_count = 1
2000-01-01 00:00:17 load chain 2 eeprom data
2000-01-01 00:00:17 board_info_version = 4
2000-01-01 00:00:17 algorithm_and_key_version = 0x11
2000-01-01 00:00:17 board_sn = FXDZYN3BAJGBC03AR
2000-01-01 00:00:17 chip_die = ED
2000-01-01 00:00:17 chip_marking = J1C021AY01
2000-01-01 00:00:17 chip_bin = 3
2000-01-01 00:00:17 ft_version = F1V04B2C1
2000-01-01 00:00:17 pcb_version = 0x110
2000-01-01 00:00:17 bom_version = 0x20
2000-01-01 00:00:17 asic_sensor_type = 0x0
2000-01-01 00:00:17 asic_sensor_addr[0] = 0x0
2000-01-01 00:00:17 asic_sensor_addr[1] = 0x0
2000-01-01 00:00:17 asic_sensor_addr[2] = 0x0
2000-01-01 00:00:17 asic_sensor_addr[3] = 0x0
2000-01-01 00:00:17 pic_sensor_type = 0x8b
2000-01-01 00:00:17 pic_sensor_addr = 0xf
2000-01-01 00:00:17 chip_tech = AA
2000-01-01 00:00:17 board_name = BHB42601
2000-01-01 00:00:17 factory_job = FXDZ20210723004-ZB
2000-01-01 00:00:17 board_info_crc = 0x8
2000-01-01 00:00:17 voltage = 1360
2000-01-01 00:00:17 frequency = 545
2000-01-01 00:00:17 nonce_rate = 9995
2000-01-01 00:00:17 pcb_temp_in = 31
2000-01-01 00:00:17 pcb_temp_out = 32
2000-01-01 00:00:17 test_version = 1
2000-01-01 00:00:17 test_standard = 0
2000-01-01 00:00:17 param_info_crc = 0x6
2000-01-01 00:00:17 pt1_result = 1
2000-01-01 00:00:17 pt1_count = 1
2000-01-01 00:00:17 pt2_result = 1
2000-01-01 00:00:17 pt2_count = 1
2000-01-01 00:00:17 fan_eft : 0  fan_pwm : 100
2000-01-01 00:00:17 create thread get_nonce_and_register_thread
2000-01-01 00:00:17 fixed working voltage = 1360
2000-01-01 00:00:17 Chain [0] PCB Version: 0x0110
2000-01-01 00:00:17 Chain [0] BOM Version: 0x0020
2000-01-01 00:00:17 Chain [1] PCB Version: 0x0110
2000-01-01 00:00:17 Chain [1] BOM Version: 0x0020
2000-01-01 00:00:17 Chain [2] PCB Version: 0x0110
2000-01-01 00:00:17 Chain [2] BOM Version: 0x0020
2000-01-01 00:00:17 Fan check passed.
2000-01-01 00:00:17 uart_trans addr:0xb6cda000.
2000-01-01 00:00:18 chain[0] PIC jump to app
2000-01-01 00:00:20 Check chain[0] PIC fw version=0x89
2000-01-01 00:00:21 chain[1] PIC jump to app
2000-01-01 00:00:22 Check chain[1] PIC fw version=0x89
2000-01-01 00:00:23 chain[2] PIC jump to app
2000-01-01 00:00:25 Check chain[2] PIC fw version=0x89
2000-01-01 00:00:25 create thread pic_heart_beat_thread
2000-01-01 00:00:25 max sensor num = 4
2000-01-01 00:00:25 i2c_sim_init start
2000-01-01 00:00:25 temperature_monitor_thread start...
2000-01-01 00:00:25 i2c_sim_init end
2021-09-14 23:33:26 power open power_version = 0x71
2021-09-14 23:33:27 power type version: 0x0071
2021-09-14 23:33:27 Enter sleep to make sure power release finish.
2021-09-14 23:33:38 chain avg vol drop to 0.84
2021-09-14 23:33:58 Slept 30 seconds, diff = 1.
2021-09-14 23:33:59 set_voltage_by_steps to 1500.
2021-09-14 23:34:02 chain avg vol rise to 9.96
2021-09-14 23:34:04 start up min temp by 75a = 19
2021-09-14 23:34:14 Chain[0]: find 126 asic, times 0
2021-09-14 23:34:14 chain avg vol rise to 14.62
2021-09-14 23:34:24 Chain[1]: find 126 asic, times 0
2021-09-14 23:34:33 Chain[2]: find 126 asic, times 0
2021-09-14 23:34:38 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2021-09-14 23:34:43 min freq in eeprom = 545
2021-09-14 23:34:43 fixed frequency is 545
2021-09-14 23:34:43 Bring up temperature is 20
2021-09-14 23:34:43 set UART baud to 3000000
2021-09-14 23:34:43 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2021-09-14 23:34:43 start do_core_reset
2021-09-14 23:35:02 end do_core_reset
2021-09-14 23:35:02 STATUS_INITED: soc init done!
2021-09-14 23:35:02 create thread check_miner_status_thread
2021-09-14 23:35:02 create thread check_system_work_thread
2021-09-14 23:35:05 start to init...
2021-09-14 23:35:05 set_voltage_by_steps to 1450.
2021-09-14 23:35:07 fixed step freq_start = 50, freq_end = 545, freq_step = 6.25
2021-09-14 23:35:07 chain = 0 set freq to 56.25
2021-09-14 23:35:07 chain = 1 set freq to 56.25
2021-09-14 23:35:07 chain = 2 set freq to 56.25
2021-09-14 23:35:07 chain = 0 set freq to 62.50
2021-09-14 23:35:07 chain = 1 set freq to 62.50
2021-09-14 23:35:07 chain = 2 set freq to 62.50
2021-09-14 23:35:07 chain = 0 set freq to 68.75
2021-09-14 23:35:07 chain = 1 set freq to 68.75
2021-09-14 23:35:07 chain = 2 set freq to 68.75
2021-09-14 23:35:07 chain = 0 set freq to 75.00
2021-09-14 23:35:07 chain = 1 set freq to 75.00
2021-09-14 23:35:07 chain = 2 set freq to 75.00
2021-09-14 23:35:07 chain = 0 set freq to 81.25
2021-09-14 23:35:07 chain = 1 set freq to 81.25
2021-09-14 23:35:07 chain = 2 set freq to 81.25
2021-09-14 23:35:07 chain = 0 set freq to 87.50
2021-09-14 23:35:07 chain = 1 set freq to 87.50
2021-09-14 23:35:07 chain = 2 set freq to 87.50
2021-09-14 23:35:07 chain = 0 set freq to 93.75
2021-09-14 23:35:07 chain = 1 set freq to 93.75
2021-09-14 23:35:07 chain = 2 set freq to 93.75
2021-09-14 23:35:07 chain = 0 set freq to 100.00
2021-09-14 23:35:07 chain = 1 set freq to 100.00
2021-09-14 23:35:07 chain = 2 set freq to 100.00
2021-09-14 23:35:08 chain = 0 set freq to 106.25
2021-09-14 23:35:08 chain = 1 set freq to 106.25
2021-09-14 23:35:08 chain = 2 set freq to 106.25
2021-09-14 23:35:08 chain = 0 set freq to 112.50
2021-09-14 23:35:08 chain = 1 set freq to 112.50
2021-09-14 23:35:08 chain = 2 set freq to 112.50
2021-09-14 23:35:08 chain = 0 set freq to 118.75
2021-09-14 23:35:08 chain = 1 set freq to 118.75
2021-09-14 23:35:08 chain = 2 set freq to 118.75
2021-09-14 23:35:08 chain = 0 set freq to 125.00
2021-09-14 23:35:08 chain = 1 set freq to 125.00
2021-09-14 23:35:08 chain = 2 set freq to 125.00
2021-09-14 23:35:08 chain = 0 set freq to 131.25
2021-09-14 23:35:08 chain = 1 set freq to 131.25
2021-09-14 23:35:08 chain = 2 set freq to 131.25
2021-09-14 23:35:08 chain = 0 set freq to 137.50
2021-09-14 23:35:08 chain = 1 set freq to 137.50
2021-09-14 23:35:08 chain = 2 set freq to 137.50
2021-09-14 23:35:08 chain = 0 set freq to 143.75
2021-09-14 23:35:08 chain = 1 set freq to 143.75
2021-09-14 23:35:08 chain = 2 set freq to 143.75
2021-09-14 23:35:08 chain = 0 set freq to 150.00
2021-09-14 23:35:08 chain = 1 set freq to 150.00
2021-09-14 23:35:08 chain = 2 set freq to 150.00
2021-09-14 23:35:08 chain = 0 set freq to 156.25
2021-09-14 23:35:08 chain = 1 set freq to 156.25
2021-09-14 23:35:08 chain = 2 set freq to 156.25
2021-09-14 23:35:09 chain = 0 set freq to 162.50
2021-09-14 23:35:09 chain = 1 set freq to 162.50
2021-09-14 23:35:09 chain = 2 set freq to 162.50
2021-09-14 23:35:09 chain = 0 set freq to 168.75
2021-09-14 23:35:09 chain = 1 set freq to 168.75
2021-09-14 23:35:09 chain = 2 set freq to 168.75
2021-09-14 23:35:09 chain = 0 set freq to 175.00
2021-09-14 23:35:09 chain = 1 set freq to 175.00
2021-09-14 23:35:09 chain = 2 set freq to 175.00
2021-09-14 23:35:09 chain = 0 set freq to 181.25
2021-09-14 23:35:09 chain = 1 set freq to 181.25
2021-09-14 23:35:09 chain = 2 set freq to 181.25
2021-09-14 23:35:09 chain = 0 set freq to 187.50
2021-09-14 23:35:09 chain = 1 set freq to 187.50
2021-09-14 23:35:09 chain = 2 set freq to 187.50
2021-09-14 23:35:09 chain = 0 set freq to 193.75
2021-09-14 23:35:09 chain = 1 set freq to 193.75
2021-09-14 23:35:09 chain = 2 set freq to 193.75
2021-09-14 23:35:09 chain = 0 set freq to 200.00
2021-09-14 23:35:09 chain = 1 set freq to 200.00
2021-09-14 23:35:09 chain = 2 set freq to 200.00
2021-09-14 23:35:09 chain = 0 set freq to 206.25
2021-09-14 23:35:09 chain = 1 set freq to 206.25
2021-09-14 23:35:09 chain = 2 set freq to 206.25
2021-09-14 23:35:09 chain = 0 set freq to 212.50
2021-09-14 23:35:09 chain = 1 set freq to 212.50
2021-09-14 23:35:09 chain = 2 set freq to 212.50
2021-09-14 23:35:09 chain = 0 set freq to 218.75
2021-09-14 23:35:09 chain = 1 set freq to 218.75
2021-09-14 23:35:09 chain = 2 set freq to 218.75
2021-09-14 23:35:10 chain = 0 set freq to 225.00
2021-09-14 23:35:10 chain = 1 set freq to 225.00
2021-09-14 23:35:10 chain = 2 set freq to 225.00
2021-09-14 23:35:10 chain = 0 set freq to 231.25
2021-09-14 23:35:10 chain = 1 set freq to 231.25
2021-09-14 23:35:10 chain = 2 set freq to 231.25
2021-09-14 23:35:10 chain = 0 set freq to 237.50
2021-09-14 23:35:10 chain = 1 set freq to 237.50
2021-09-14 23:35:10 chain = 2 set freq to 237.50
2021-09-14 23:35:10 chain = 0 set freq to 243.75
2021-09-14 23:35:10 chain = 1 set freq to 243.75
2021-09-14 23:35:10 chain = 2 set freq to 243.75
2021-09-14 23:35:10 chain = 0 set freq to 250.00
2021-09-14 23:35:10 chain = 1 set freq to 250.00
2021-09-14 23:35:10 chain = 2 set freq to 250.00
2021-09-14 23:35:10 chain = 0 set freq to 256.25
2021-09-14 23:35:10 chain = 1 set freq to 256.25
2021-09-14 23:35:10 chain = 2 set freq to 256.25
2021-09-14 23:35:10 chain = 0 set freq to 262.50
2021-09-14 23:35:10 chain = 1 set freq to 262.50
2021-09-14 23:35:10 chain = 2 set freq to 262.50
2021-09-14 23:35:10 chain = 0 set freq to 268.75
2021-09-14 23:35:10 chain = 1 set freq to 268.75
2021-09-14 23:35:10 chain = 2 set freq to 268.75
2021-09-14 23:35:10 chain = 0 set freq to 275.00
2021-09-14 23:35:10 chain = 1 set freq to 275.00
2021-09-14 23:35:10 chain = 2 set freq to 275.00
2021-09-14 23:35:11 chain = 0 set freq to 281.25
2021-09-14 23:35:11 chain = 1 set freq to 281.25
2021-09-14 23:35:11 chain = 2 set freq to 281.25
2021-09-14 23:35:11 chain = 0 set freq to 287.50
2021-09-14 23:35:11 chain = 1 set freq to 287.50
2021-09-14 23:35:11 chain = 2 set freq to 287.50
2021-09-14 23:35:11 chain = 0 set freq to 293.75
2021-09-14 23:35:11 chain = 1 set freq to 293.75
2021-09-14 23:35:11 chain = 2 set freq to 293.75
2021-09-14 23:35:11 chain = 0 set freq to 300.00
2021-09-14 23:35:11 chain = 1 set freq to 300.00
2021-09-14 23:35:11 chain = 2 set freq to 300.00
2021-09-14 23:35:11 chain = 0 set freq to 306.25
2021-09-14 23:35:11 chain = 1 set freq to 306.25
2021-09-14 23:35:11 chain = 2 set freq to 306.25
2021-09-14 23:35:11 chain = 0 set freq to 312.50
2021-09-14 23:35:11 chain = 1 set freq to 312.50
2021-09-14 23:35:11 chain = 2 set freq to 312.50
2021-09-14 23:35:11 chain = 0 set freq to 318.75
2021-09-14 23:35:11 chain = 1 set freq to 318.75
2021-09-14 23:35:11 chain = 2 set freq to 318.75
2021-09-14 23:35:11 chain = 0 set freq to 325.00
2021-09-14 23:35:11 chain = 1 set freq to 325.00
2021-09-14 23:35:11 chain = 2 set freq to 325.00
2021-09-14 23:35:11 chain = 0 set freq to 331.25
2021-09-14 23:35:11 chain = 1 set freq to 331.25
2021-09-14 23:35:11 chain = 2 set freq to 331.25
2021-09-14 23:35:11 chain = 0 set freq to 337.50
2021-09-14 23:35:11 chain = 1 set freq to 337.50
2021-09-14 23:35:11 chain = 2 set freq to 337.50
2021-09-14 23:35:12 chain = 0 set freq to 343.75
2021-09-14 23:35:12 chain = 1 set freq to 343.75
2021-09-14 23:35:12 chain = 2 set freq to 343.75
2021-09-14 23:35:12 chain = 0 set freq to 350.00
2021-09-14 23:35:12 chain = 1 set freq to 350.00
2021-09-14 23:35:12 chain = 2 set freq to 350.00
2021-09-14 23:35:12 chain = 0 set freq to 356.25
2021-09-14 23:35:12 chain = 1 set freq to 356.25
2021-09-14 23:35:12 chain = 2 set freq to 356.25
2021-09-14 23:35:12 chain = 0 set freq to 362.50
2021-09-14 23:35:12 chain = 1 set freq to 362.50
2021-09-14 23:35:12 chain = 2 set freq to 362.50
2021-09-14 23:35:12 chain = 0 set freq to 368.75
2021-09-14 23:35:12 chain = 1 set freq to 368.75
2021-09-14 23:35:12 chain = 2 set freq to 368.75
2021-09-14 23:35:12 chain = 0 set freq to 375.00
2021-09-14 23:35:12 chain = 1 set freq to 375.00
2021-09-14 23:35:12 chain = 2 set freq to 375.00
2021-09-14 23:35:12 chain = 0 set freq to 381.25
2021-09-14 23:35:12 chain = 1 set freq to 381.25
2021-09-14 23:35:12 chain = 2 set freq to 381.25
2021-09-14 23:35:12 chain = 0 set freq to 387.50
2021-09-14 23:35:12 chain = 1 set freq to 387.50
2021-09-14 23:35:12 chain = 2 set freq to 387.50
2021-09-14 23:35:12 chain = 0 set freq to 393.75
2021-09-14 23:35:12 chain = 1 set freq to 393.75
2021-09-14 23:35:12 chain = 2 set freq to 393.75
2021-09-14 23:35:12 chain = 0 set freq to 400.00
2021-09-14 23:35:12 chain = 1 set freq to 400.00
2021-09-14 23:35:12 chain = 2 set freq to 400.00
2021-09-14 23:35:13 chain = 0 set freq to 406.25
2021-09-14 23:35:13 chain = 1 set freq to 406.25
2021-09-14 23:35:13 chain = 2 set freq to 406.25
2021-09-14 23:35:13 chain = 0 set freq to 412.50
2021-09-14 23:35:13 chain = 1 set freq to 412.50
2021-09-14 23:35:13 chain = 2 set freq to 412.50
2021-09-14 23:35:13 chain = 0 set freq to 418.75
2021-09-14 23:35:13 chain = 1 set freq to 418.75
2021-09-14 23:35:13 chain = 2 set freq to 418.75
2021-09-14 23:35:13 chain = 0 set freq to 425.00
2021-09-14 23:35:13 chain = 1 set freq to 425.00
2021-09-14 23:35:13 chain = 2 set freq to 425.00
2021-09-14 23:35:13 chain = 0 set freq to 431.25
2021-09-14 23:35:13 chain = 1 set freq to 431.25
2021-09-14 23:35:13 chain = 2 set freq to 431.25
2021-09-14 23:35:13 chain = 0 set freq to 437.50
2021-09-14 23:35:13 chain = 1 set freq to 437.50
2021-09-14 23:35:13 chain = 2 set freq to 437.50
2021-09-14 23:35:13 chain = 0 set freq to 443.75
2021-09-14 23:35:13 chain = 1 set freq to 443.75
2021-09-14 23:35:13 chain = 2 set freq to 443.75
2021-09-14 23:35:13 chain = 0 set freq to 450.00
2021-09-14 23:35:13 chain = 1 set freq to 450.00
2021-09-14 23:35:13 chain = 2 set freq to 450.00
2021-09-14 23:35:13 chain = 0 set freq to 456.25
2021-09-14 23:35:13 chain = 1 set freq to 456.25
2021-09-14 23:35:13 chain = 2 set freq to 456.25
2021-09-14 23:35:14 chain = 0 set freq to 462.50
2021-09-14 23:35:14 chain = 1 set freq to 462.50
2021-09-14 23:35:14 chain = 2 set freq to 462.50
2021-09-14 23:35:14 chain = 0 set freq to 468.75
2021-09-14 23:35:14 chain = 1 set freq to 468.75
2021-09-14 23:35:14 chain = 2 set freq to 468.75
2021-09-14 23:35:14 chain = 0 set freq to 475.00
2021-09-14 23:35:14 chain = 1 set freq to 475.00
2021-09-14 23:35:14 chain = 2 set freq to 475.00
2021-09-14 23:35:14 chain = 0 set freq to 481.25
2021-09-14 23:35:14 chain = 1 set freq to 481.25
2021-09-14 23:35:14 chain = 2 set freq to 481.25
2021-09-14 23:35:14 chain = 0 set freq to 487.50
2021-09-14 23:35:14 chain = 1 set freq to 487.50
2021-09-14 23:35:14 chain = 2 set freq to 487.50
2021-09-14 23:35:14 chain = 0 set freq to 493.75
2021-09-14 23:35:14 chain = 1 set freq to 493.75
2021-09-14 23:35:14 chain = 2 set freq to 493.75
2021-09-14 23:35:14 chain = 0 set freq to 500.00
2021-09-14 23:35:14 chain = 1 set freq to 500.00
2021-09-14 23:35:14 chain = 2 set freq to 500.00
2021-09-14 23:35:14 chain = 0 set freq to 506.25
2021-09-14 23:35:14 chain = 1 set freq to 506.25
2021-09-14 23:35:14 chain = 2 set freq to 506.25
2021-09-14 23:35:14 chain = 0 set freq to 512.50
2021-09-14 23:35:14 chain = 1 set freq to 512.50
2021-09-14 23:35:14 chain = 2 set freq to 512.50
2021-09-14 23:35:14 chain = 0 set freq to 518.75
2021-09-14 23:35:14 chain = 1 set freq to 518.75
2021-09-14 23:35:14 chain = 2 set freq to 518.75
2021-09-14 23:35:15 chain = 0 set freq to 525.00
2021-09-14 23:35:15 chain = 1 set freq to 525.00
2021-09-14 23:35:15 chain = 2 set freq to 525.00
2021-09-14 23:35:15 chain = 0 set freq to 531.25
2021-09-14 23:35:15 chain = 1 set freq to 531.25
2021-09-14 23:35:15 chain = 2 set freq to 531.25
2021-09-14 23:35:15 chain = 0 set freq to 537.50
2021-09-14 23:35:15 chain = 1 set freq to 537.50
2021-09-14 23:35:15 chain = 2 set freq to 537.50
2021-09-14 23:35:15 chain = 0 set freq to 543.75
2021-09-14 23:35:15 chain = 1 set freq to 543.75
2021-09-14 23:35:15 chain = 2 set freq to 543.75
2021-09-14 23:35:15 chain = 0 set freq to 545.00
2021-09-14 23:35:15 chain = 1 set freq to 545.00
2021-09-14 23:35:15 chain = 2 set freq to 545.00
2021-09-14 23:35:16 set_voltage_by_steps to 1360.
2021-09-14 23:35:17 Init done!
2021-09-14 23:35:17 STATUS_OKAY
2021-09-14 23:35:17 start the cached job
2021-09-14 23:35:17 Version num 1
2021-09-14 23:35:17 Mask num 0x0
2021-09-14 23:35:18 opt_multi_version = 1, interval timeout = 43
2021-09-14 23:35:18 freq = 545, percent = 90, hcn = 4809, timeout = 43
2021-09-14 23:35:18 set_start_time_point total_tv_start_sys=141 total_tv_end_sys=142
2021-09-14 23:35:40 set_voltage_by_steps to 1392.
2021-09-14 23:37:02 !!! reg crc error
2021-09-14 23:37:06 set_voltage_by_steps to 1382.
2021-09-14 23:37:08 set_voltage_by_steps to 1372.
2021-09-14 23:37:10 set_voltage_by_steps to 1362.
2021-09-14 23:37:13 curr_vol = 1362, g_voltage = 1360,entrance_temp = 23
2021-09-14 23:37:13 set_voltage_by_steps to 1360.
2021-09-14 23:38:28 !!! reg crc error
2021-09-14 23:42:54 !!! reg crc error
2021-09-14 23:43:52 !!! reg crc error
2021-09-14 23:44:26 !!! reg crc error
2021-09-14 23:44:26 !!! reg crc error
2021-09-14 23:48:05 !!! reg crc error
2021-09-14 23:49:33 !!! reg crc error
2021-09-14 23:54:17 !!! reg crc error
2021-09-14 23:56:55 !!! reg crc error