S19j Pro - Data load fail for chain 0.
已回答
1970-01-01 00:00:09 Miner compile time: Sat May 15 21:17:18 CST 2021 type: Antminer S19j Pro
1970-01-01 00:00:10 This is fix-freq version
1970-01-01 00:00:10 Miner compile time: Sat May 15 21:17:18 CST 2021 type: Antminer S19j Pro
1970-01-01 00:00:10 commit åversion: 46c2188 2021-05-15 21:14:17, build by: jenkins 2021-05-15 21:17:17
1970-01-01 00:00:10 opt_multi_version = 1
1970-01-01 00:00:10 opt_bitmain_ab = 1
1970-01-01 00:00:10 mid_auto_gen = 0
1970-01-01 00:00:10 opt_bitmain_work_mode = 0
1970-01-01 00:00:10 mmap fpga_mem_addr_hal = 0xb5800000
1970-01-01 00:00:10 HASH_ON_PLUG V9 = 0x7
1970-01-01 00:00:10 Note: front fan is power on!
1970-01-01 00:00:10 Note: rear fan is power on!
1970-01-01 00:00:10 start the http log.
1970-01-01 00:00:10 httpListenThread start ret=0
1970-01-01 00:00:10 start listen on 6060 ...
1970-01-01 00:00:10 load machine BHB42601 conf
1970-01-01 00:00:10 machine : BHB42601
1970-01-01 00:00:10 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2021-09-12 13:21:03 miner ID : 8038e5064e10481c
2021-09-12 13:21:03 FPGA Version = 0xB031
2021-09-12 13:21:03 HASH_ON_PLUG V9 = 0x7
2021-09-12 13:21:03 ==========================capability start==========================
2021-09-12 13:21:03 board num = 3
2021-09-12 13:21:03 board id = 0, chain num = 1
2021-09-12 13:21:03 chain id = 0
2021-09-12 13:21:03 board id = 1, chain num = 1
2021-09-12 13:21:03 chain id = 1
2021-09-12 13:21:03 board id = 2, chain num = 1
2021-09-12 13:21:03 chain id = 2
2021-09-12 13:21:03 ==========================capability end============================
2021-09-12 13:21:03 chain num = 3
2021-09-12 13:21:05 load chain 0 eeprom data
2021-09-12 13:21:05 version invalid 0!=4
2021-09-12 13:21:05 got nothing
2021-09-12 13:21:06 load chain 0 eeprom data
2021-09-12 13:21:06 version invalid 0!=4
2021-09-12 13:21:06 got nothing
2021-09-12 13:21:08 load chain 0 eeprom data
2021-09-12 13:21:08 version invalid 0!=4
2021-09-12 13:21:08 got nothing
2021-09-12 13:21:08 Data load fail for chain 0.
2021-09-12 13:21:10 load chain 1 eeprom data
2021-09-12 13:21:10 board_info_version = 4
2021-09-12 13:21:10 algorithm_and_key_version = 0x11
2021-09-12 13:21:10 board_sn = YDFTYN3BAJEAG0JRZ
2021-09-12 13:21:10 chip_die = ED
2021-09-12 13:21:10 chip_marking = S1CT21AY34
2021-09-12 13:21:10 chip_bin = 3
2021-09-12 13:21:10 ft_version = F1V04B2C1
2021-09-12 13:21:10 pcb_version = 0x100
2021-09-12 13:21:10 bom_version = 0x10
2021-09-12 13:21:10 asic_sensor_type = 0x0
2021-09-12 13:21:10 asic_sensor_addr[0] = 0x0
2021-09-12 13:21:10 asic_sensor_addr[1] = 0x0
2021-09-12 13:21:10 asic_sensor_addr[2] = 0x0
2021-09-12 13:21:10 asic_sensor_addr[3] = 0x0
2021-09-12 13:21:10 pic_sensor_type = 0x81
2021-09-12 13:21:10 pic_sensor_addr = 0x1
2021-09-12 13:21:10 chip_tech = AA
2021-09-12 13:21:10 board_name = BHB42601
2021-09-12 13:21:10 factory_job = YDFT20210517002-ZB
2021-09-12 13:21:10 board_info_crc = 0x0
2021-09-12 13:21:10 voltage = 1360
2021-09-12 13:21:10 frequency = 525
2021-09-12 13:21:10 nonce_rate = 9996
2021-09-12 13:21:10 pcb_temp_in = 35
2021-09-12 13:21:10 pcb_temp_out = 37
2021-09-12 13:21:10 test_version = 1
2021-09-12 13:21:10 test_standard = 0
2021-09-12 13:21:10 param_info_crc = 0x16
2021-09-12 13:21:10 pt1_result = 1
2021-09-12 13:21:10 pt1_count = 1
2021-09-12 13:21:10 pt2_result = 1
2021-09-12 13:21:10 pt2_count = 1
2021-09-12 13:21:12 load chain 2 eeprom data
2021-09-12 13:21:12 board_info_version = 4
2021-09-12 13:21:12 algorithm_and_key_version = 0x11
2021-09-12 13:21:12 board_sn = YDFTYN3BAJEAG0JSD
2021-09-12 13:21:12 chip_die = ED
2021-09-12 13:21:12 chip_marking = S1CT21AY34
2021-09-12 13:21:12 chip_bin = 3
2021-09-12 13:21:12 ft_version = F1V04B2C1
2021-09-12 13:21:12 pcb_version = 0x100
2021-09-12 13:21:12 bom_version = 0x10
2021-09-12 13:21:12 asic_sensor_type = 0x0
2021-09-12 13:21:12 asic_sensor_addr[0] = 0x0
2021-09-12 13:21:12 asic_sensor_addr[1] = 0x0
2021-09-12 13:21:12 asic_sensor_addr[2] = 0x0
2021-09-12 13:21:12 asic_sensor_addr[3] = 0x0
2021-09-12 13:21:12 pic_sensor_type = 0x81
2021-09-12 13:21:12 pic_sensor_addr = 0x1
2021-09-12 13:21:12 chip_tech = AA
2021-09-12 13:21:12 board_name = BHB42601
2021-09-12 13:21:12 factory_job = YDFT20210517002-ZB
2021-09-12 13:21:12 board_info_crc = 0x17
2021-09-12 13:21:12 voltage = 1360
2021-09-12 13:21:12 frequency = 525
2021-09-12 13:21:12 nonce_rate = 9999
2021-09-12 13:21:12 pcb_temp_in = 35
2021-09-12 13:21:12 pcb_temp_out = 37
2021-09-12 13:21:12 test_version = 1
2021-09-12 13:21:12 test_standard = 0
2021-09-12 13:21:12 param_info_crc = 0x7
2021-09-12 13:21:12 pt1_result = 1
2021-09-12 13:21:12 pt1_count = 1
2021-09-12 13:21:12 pt2_result = 1
2021-09-12 13:21:12 pt2_count = 1
2021-09-12 13:21:12 Sweep error string = J255:4.
2021-09-12 13:21:12 Fixture data load failed, exit.
2021-09-12 13:21:12 ERROR_SOC_INIT: basic init failed!
2021-09-12 13:21:12 stop_mining: basic init failed!
2021-09-12 13:21:12 ****power off hashboard****
2021-09-12 13:21:13 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0x5a, read_back_data[1] = 0x5a
2021-09-12 13:21:13 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0xff, read_back_data[1] = 0xff
2021-09-12 13:21:14 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0xff, read_back_data[1] = 0xff
-
正式评论
Dear
It showed ERROR_SOC_INIT: basic init failed!
Could you try the below instructions:
1 Plug and unplug the cable,
2 Flashing the sd card to recover to the control board,
3 Configure whether there is a mix board
评论操作 -
BEWARE!
DO NOT INSTALL the S19j Pro SD card recovery package. It has BRICKED our miner!
- Antminer-S19j-Pro-Release-sd2nand-zynq7007-20210605.zip (file size 26.87MB)
- S19j Pro SD firmware for 7007 control board only (published 2021-08-26)
This package is identical to the S19j package. We have compared and match both packages' "update.bmu" file checksums. Your miner will not be able to detect hash boards, reset to factory default firmware, or update to the Antminer-S19j-Pro-release-202106281212.bin firmware. Effectively rendering your equipment useless.
Bitmain support, please send the correct S19j Pro 100T (7007) recovery to niftyframes@protonmail.com
-
Hello, i have the same problem, Miner worked fine first day, then Board 0 went low hashrate (20Th),
Restarting the miner and now if shows * No data yet! Data is currently unavailable *
on the Log here
Asic : S19J PRO 104T ( Amlogic board ) , just unboxed the miner brand new2023-03-17 09:22:49 Chain[0]: find 73 asic, times 0 2023-03-17 09:22:51 Chain[0]: find 73 asic, times 1 2023-03-17 09:22:53 Chain[0]: find 73 asic, times 2 2023-03-17 09:22:53 Chain 0 only find 73 asic, will power off hash board 0 2023-03-17 09:22:55 Chain[1]: find 126 asic, times 0 2023-03-17 09:22:57 Chain[2]: find 126 asic, times 0 2023-03-17 09:22:57 ERROR_SOC_INIT: soc init failed!
Any help on this
-
Dear customer.
From the kernel log, it can't detect all chips. please kindly exclude the issue by following steps:
1.Check the wires for the hashboard--pull them and re-plug them again, and also you can try to change the new wires.
2.Please clean up the dust.
How To Clean and Dust The Antminers
https://support.bitmain.com/hc/en-us/articles/115004520173-How-To-Clean-and-Dust-The-Antminers
3.Test for PSU failure and ensure the miner is grounded well.
https://support.bitmain.com/hc/en-us/articles/115004339274--How-to-use-a-multimeter-to-test-PSU
If there are still the same problems after the above steps, please send it to repair.
Best regards
BITMAIN
-
Dear Customer,
If you have any questions please feel free to contact us.
Please send email to customersupport@bitmain.com
We will reply to your question as soon as possible.
-
Hi ! I have the same problem , my miner working for 3 hours , after that one hashboard show to be faulty , i replaced all the cable, new PSU , new control board ( networking ) , upgrade last firmware ( Antminer-S19j-Pro-merge-release-20221226125147 ) , SD format ( s19j-Pro-a113d-amlctrl-flashCard-20211119 ) , factory reset .......
Nothing changed , the same problem !!!
Where can i buy new hasboard BHB42603, version ? NOT BHB42601
i buy a new hasboard but my mistake the version was BHB42601 , and its not working
Any solution ?
thanks !
start==========================
2023-05-02 10:02:36 board num = 3
2023-05-02 10:02:36 board id = 0, chain num = 1
2023-05-02 10:02:36 chain id = 0
2023-05-02 10:02:36 board id = 1, chain num = 1
2023-05-02 10:02:36 chain id = 1
2023-05-02 10:02:36 board id = 2, chain num = 1
2023-05-02 10:02:36 chain id = 2
2023-05-02 10:02:36 ==========================capability end============================
2023-05-02 10:02:36 chain num = 3
2023-05-02 10:02:36 skip loading levels for now
2023-05-02 10:02:40 load chain 0 eeprom data
2023-05-02 10:02:43 load chain 1 eeprom data
2023-05-02 10:02:46 load chain 2 eeprom data
2023-05-02 10:02:46 get a different board name for chain:2, pre board_name:BHB42603, current board_name:BHB42601
2023-05-02 10:02:46 ERROR_SOC_INIT: basic init failed!
2023-05-02 10:02:46 stop_mining: basic init failed!
2023-05-02 10:02:46 *power off hashboard*Chain 2 only find 124 asic, will power off hash board
may take up to 2 minutes...
2023-05-02 11:15:35 Slept 30 seconds, diff = 1.
2023-05-02 11:15:39 set_voltage_by_steps to 1500.
2023-05-02 11:15:48 start up min temp by 75a = 21
2023-05-02 11:15:51 Chain[0]: find 126 asic, times 0
2023-05-02 11:15:53 Chain[1]: find 126 asic, times 0
2023-05-02 11:15:53 !!! reg crc error
2023-05-02 11:15:55 Chain[2]: find 124 asic, times 0
2023-05-02 11:15:55 !!! reg crc error
2023-05-02 11:15:57 Chain[2]: find 124 asic, times 1
2023-05-02 11:15:57 !!! reg crc error
2023-05-02 11:15:59 Chain[2]: find 124 asic, times 2
2023-05-02 11:15:59 Chain 2 only find 124 asic, will power off hash board 2
2023-05-02 11:15:59 ERROR_SOC_INIT: soc init failed!
2023-05-02 11:15:59 stop_mining: soc init failed! -
Dear Customer,
If you have any questions please feel free to contact us.
Please send email to customersupport@bitmain.com
We will reply to your question as soon as possible.
请先登录再写评论。
评论
8 条评论