S19J Pro 1 Defekt Hashboard and the 2 others work with just 200 Hz of Frequency
Hello Community,
I hope someone can help me.
I have an S19J Pro Miner, and one of the hashboards seems to be broken.
First, I tested it by unplugging for a long duration, resetting, updating the firmware (12/26/2022), and swapping the boards to another position.
One board seems to have a temperature failure, but the other two are fine.
When I start the miner, the frequency won't go higher than 200 Hz. Is it possible to operate with just the two working hashboards until I have time to repair the third one?
Thats the temp Fail with 3 boards. __________________________________________________________________
2024-08-20 16:00:43 temperature_monitor_thread start...
2024-08-20 16:00:43 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
__________________________________________________________________
and her the complet log run with 2 boards:
1970-01-01 00:00:10 Invalid config option --bitmain-freq-level: '' is not a number
1970-01-01 00:00:10 Open miner sn file /config/sn error
1970-01-01 00:00:10 Miner compile time: Mon Dec 26 17:09:26 CST 2022 type: Antminer BHB42XXX sn :
1970-01-01 00:00:11 This is fix-freq version
1970-01-01 00:00:11 Miner compile time: Mon Dec 26 17:09:26 CST 2022 type: Antminer BHB42XXX
1970-01-01 00:00:11 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 17:09:25
1970-01-01 00:00:11 opt_multi_version = 1
1970-01-01 00:00:11 opt_bitmain_ab = 1
1970-01-01 00:00:11 mid_auto_gen = 0
1970-01-01 00:00:11 opt_bitmain_work_mode = 3
1970-01-01 00:00:11 mmap fpga_mem_addr_hal = 0xb5800000
1970-01-01 00:00:11 HASH_ON_PLUG V9 = 0x6
1970-01-01 00:00:11 Note: front fan is power on!
1970-01-01 00:00:11 Note: rear fan is power on!
1970-01-01 00:00:11 start the http log.
1970-01-01 00:00:11 httpListenThread start ret=0
1970-01-01 00:00:11 start listen on 6060 ...
1970-01-01 00:00:17 miner ID : 8010ecc82b104814
1970-01-01 00:00:17 FPGA Version = 0xB042
1970-01-01 00:00:17 HASH_ON_PLUG V9 = 0x6
1970-01-01 00:00:17 ==========================capability start==========================
1970-01-01 00:00:17 board num = 2
1970-01-01 00:00:17 board id = 1, chain num = 1
1970-01-01 00:00:17 chain id = 1
1970-01-01 00:00:17 board id = 2, chain num = 1
1970-01-01 00:00:17 chain id = 2
1970-01-01 00:00:17 ==========================capability end============================
1970-01-01 00:00:17 chain num = 2
1970-01-01 00:00:17 skip loading levels for now
2024-08-21 05:48:41 load chain 1 eeprom data
2024-08-21 05:48:48 load chain 2 eeprom data
2024-08-21 05:48:50 power open power_version = 0x71
2024-08-21 05:48:56 power is not Calibrated
2024-08-21 05:48:59 miner type: Antminer S19j Pro
2024-08-21 05:48:59 multi machine mode
2024-08-21 05:48:59 load machine BHB42601 conf
2024-08-21 05:48:59 machine : BHB42601
2024-08-21 05:48:59 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2024-08-21 05:48:59 abandon mix board!
2024-08-21 05:48:59 abandon mix board!
2024-08-21 05:48:59 fan_eft : 0 fan_pwm : 100
2024-08-21 05:48:59 create thread get_nonce_and_register_thread
2024-08-21 05:48:59 fixed working voltage = 1320
2024-08-21 05:48:59 failed to load freq in eeprom, using default
2024-08-21 05:48:59 fixed frequency is 200
2024-08-21 05:48:59 Chain [1] PCB Version: 0x0100
2024-08-21 05:48:59 Chain [1] BOM Version: 0x0010
2024-08-21 05:48:59 Chain [2] PCB Version: 0x0100
2024-08-21 05:48:59 Chain [2] BOM Version: 0x0010
2024-08-21 05:48:59 Fan check passed.
2024-08-21 05:49:00 chain[1] PIC jump to app
2024-08-21 05:49:01 Check chain[1] PIC fw version=0x89
2024-08-21 05:49:03 chain[2] PIC jump to app
2024-08-21 05:49:04 Check chain[2] PIC fw version=0x89
2024-08-21 05:49:05 create thread pic_heart_beat_thread
2024-08-21 05:49:05 max sensor num = 4
2024-08-21 05:49:05 STATUS_INITED: soc init done!
2024-08-21 05:49:05 temperature_monitor_thread start...
2024-08-21 05:49:06 start to init...
2024-08-21 05:49:06 warning:power is not calibration.
2024-08-21 05:49:08 power type version: 0x0071
2024-08-21 05:49:08 Initializing the power, please wait, this may take up to 2 minutes...
2024-08-21 05:49:39 Slept 30 seconds, diff = 0.
2024-08-21 05:49:40 set_voltage_by_steps to 1500.
2024-08-21 05:49:44 chain avg vol rise to 15.33
2024-08-21 05:49:45 start up min temp by 75a = 16
2024-08-21 05:49:45 set UART baud to 115200
2024-08-21 05:49:56 Chain[1]: find 126 asic, times 0
2024-08-21 05:50:06 Chain[2]: find 126 asic, times 0
2024-08-21 05:50:11 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2024-08-21 05:50:14 Bring up temperature is 16
2024-08-21 05:50:14 set UART baud to 12000000
2024-08-21 05:50:14 create thread check_miner_status_thread
2024-08-21 05:50:14 create thread check_system_work_thread
2024-08-21 05:50:14 set_voltage_by_steps to 1450.
2024-08-21 05:50:18 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2024-08-21 05:50:18 start do_core_reset
2024-08-21 05:50:32 end do_core_reset
2024-08-21 05:50:32 chain[1] min = 90 max =90
2024-08-21 05:50:32 chain[2] min = 90 max =90
2024-08-21 05:50:32 1.inc all chain freq to 90
2024-08-21 05:50:32 fixed step freq_start = 50, freq_end = 90, freq_step = 6.25
2024-08-21 05:50:32 chain = 1 set freq to 56.25
2024-08-21 05:50:32 chain = 2 set freq to 56.25
2024-08-21 05:50:32 chain = 1 set freq to 62.50
2024-08-21 05:50:32 chain = 2 set freq to 62.50
2024-08-21 05:50:32 chain = 1 set freq to 68.75
2024-08-21 05:50:32 chain = 2 set freq to 68.75
2024-08-21 05:50:33 chain = 1 set freq to 75.00
2024-08-21 05:50:33 chain = 2 set freq to 75.00
2024-08-21 05:50:33 chain = 1 set freq to 81.25
2024-08-21 05:50:33 chain = 2 set freq to 81.25
2024-08-21 05:50:33 chain = 1 set freq to 87.50
2024-08-21 05:50:33 chain = 2 set freq to 87.50
2024-08-21 05:50:34 chain = 1 set freq to 90.00
2024-08-21 05:50:34 chain = 2 set freq to 90.00
2024-08-21 05:50:34 enter mixed freq cfg
2024-08-21 05:50:34 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2024-08-21 05:50:34 start do_core_reset
2024-08-21 05:50:48 end do_core_reset
2024-08-21 05:50:58 set_voltage_by_steps to 1214.
2024-08-21 05:51:01 Init done!
2024-08-21 05:51:01 STATUS_OKAY
2024-08-21 05:51:01 start the cached job
2024-08-21 05:51:01 Version num 8
2024-08-21 05:51:01 Mask num 0xe000
2024-08-21 05:51:01 freq = 90, percent = 90, hcn = 29126, timeout = 2096
2024-08-21 05:51:01 set_start_time_point total_tv_start_sys=165 total_tv_end_sys=166
2024-08-21 05:51:01 set_voltage_by_steps to 1247.
2024-08-21 05:55:12 Invalid config option --bitmain-freq-level: '' is not a number
2024-08-21 05:55:12 Open miner sn file /config/sn error
2024-08-21 05:55:12 Miner compile time: Mon Dec 26 17:09:26 CST 2022 type: Antminer S19j Pro sn :
2024-08-21 05:55:13 This is fix-freq version
2024-08-21 05:55:13 Miner compile time: Mon Dec 26 17:09:26 CST 2022 type: Antminer S19j Pro
2024-08-21 05:55:13 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 17:09:25
2024-08-21 05:55:13 opt_multi_version = 1
2024-08-21 05:55:13 opt_bitmain_ab = 1
2024-08-21 05:55:13 mid_auto_gen = 0
2024-08-21 05:55:13 opt_bitmain_work_mode = 0
2024-08-21 05:55:13 mmap fpga_mem_addr_hal = 0xb5700000
2024-08-21 05:55:13 HASH_ON_PLUG V9 = 0x6
2024-08-21 05:55:13 Note: front fan is power on!
2024-08-21 05:55:13 Note: rear fan is power on!
2024-08-21 05:55:13 start the http log.
2024-08-21 05:55:13 httpListenThread start ret=0
2024-08-21 05:55:13 start listen on 6060 ...
2024-08-21 05:55:19 miner ID : 8010ecc82b104814
2024-08-21 05:55:19 FPGA Version = 0xB042
2024-08-21 05:55:19 HASH_ON_PLUG V9 = 0x6
2024-08-21 05:55:19 ==========================capability start==========================
2024-08-21 05:55:19 board num = 2
2024-08-21 05:55:19 board id = 1, chain num = 1
2024-08-21 05:55:19 chain id = 1
2024-08-21 05:55:19 board id = 2, chain num = 1
2024-08-21 05:55:19 chain id = 2
2024-08-21 05:55:19 ==========================capability end============================
2024-08-21 05:55:19 chain num = 2
2024-08-21 05:55:19 skip loading levels for now
2024-08-21 05:55:26 load chain 1 eeprom data
2024-08-21 05:55:33 load chain 2 eeprom data
2024-08-21 05:55:35 power open power_version = 0x71
2024-08-21 05:55:41 power is not Calibrated
2024-08-21 05:55:43 miner type: Antminer S19j Pro
2024-08-21 05:55:43 multi machine mode
2024-08-21 05:55:43 load machine BHB42601 conf
2024-08-21 05:55:43 machine : BHB42601
2024-08-21 05:55:43 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2024-08-21 05:55:43 abandon mix board!
2024-08-21 05:55:43 abandon mix board!
2024-08-21 05:55:43 fan_eft : 0 fan_pwm : 100
2024-08-21 05:55:43 create thread get_nonce_and_register_thread
2024-08-21 05:55:43 fixed working voltage = 1320
2024-08-21 05:55:43 failed to load freq in eeprom, using default
2024-08-21 05:55:43 fixed frequency is 200
2024-08-21 05:55:43 Chain [1] PCB Version: 0x0100
2024-08-21 05:55:43 Chain [1] BOM Version: 0x0010
2024-08-21 05:55:43 Chain [2] PCB Version: 0x0100
2024-08-21 05:55:43 Chain [2] BOM Version: 0x0010
2024-08-21 05:55:43 Fan check passed.
2024-08-21 05:55:44 chain[1] PIC jump to app
2024-08-21 05:55:46 Check chain[1] PIC fw version=0x89
2024-08-21 05:55:47 chain[2] PIC jump to app
2024-08-21 05:55:49 Check chain[2] PIC fw version=0x89
2024-08-21 05:55:49 create thread pic_heart_beat_thread
2024-08-21 05:55:49 max sensor num = 4
2024-08-21 05:55:49 STATUS_INITED: soc init done!
2024-08-21 05:55:49 temperature_monitor_thread start...
2024-08-21 05:55:51 start to init...
2024-08-21 05:55:51 warning:power is not calibration.
2024-08-21 05:55:53 power type version: 0x0071
2024-08-21 05:55:53 Initializing the power, please wait, this may take up to 2 minutes...
2024-08-21 05:56:30 Slept 36 seconds, diff = 3.
2024-08-21 05:56:31 set_voltage_by_steps to 1500.
2024-08-21 05:56:35 chain avg vol rise to 15.32
2024-08-21 05:56:36 start up min temp by 75a = 17
2024-08-21 05:56:36 set UART baud to 115200
2024-08-21 05:56:46 Chain[1]: find 126 asic, times 0
2024-08-21 05:56:56 Chain[2]: find 126 asic, times 0
2024-08-21 05:57:01 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2024-08-21 05:57:05 Bring up temperature is 17
2024-08-21 05:57:05 set UART baud to 12000000
2024-08-21 05:57:05 create thread check_miner_status_thread
2024-08-21 05:57:05 create thread check_system_work_thread
2024-08-21 05:57:05 set_voltage_by_steps to 1450.
2024-08-21 05:57:08 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2024-08-21 05:57:08 start do_core_reset
2024-08-21 05:57:22 end do_core_reset
2024-08-21 05:57:22 chain[1] min = 200 max =200
2024-08-21 05:57:22 chain[2] min = 200 max =200
2024-08-21 05:57:22 1.inc all chain freq to 200
2024-08-21 05:57:22 fixed step freq_start = 50, freq_end = 200, freq_step = 6.25
2024-08-21 05:57:22 chain = 1 set freq to 56.25
2024-08-21 05:57:22 chain = 2 set freq to 56.25
2024-08-21 05:57:23 chain = 1 set freq to 62.50
2024-08-21 05:57:23 chain = 2 set freq to 62.50
2024-08-21 05:57:23 chain = 1 set freq to 68.75
2024-08-21 05:57:23 chain = 2 set freq to 68.75
2024-08-21 05:57:23 chain = 1 set freq to 75.00
2024-08-21 05:57:23 chain = 2 set freq to 75.00
2024-08-21 05:57:24 chain = 1 set freq to 81.25
2024-08-21 05:57:24 chain = 2 set freq to 81.25
2024-08-21 05:57:24 chain = 1 set freq to 87.50
2024-08-21 05:57:24 chain = 2 set freq to 87.50
2024-08-21 05:57:24 chain = 1 set freq to 93.75
2024-08-21 05:57:24 chain = 2 set freq to 93.75
2024-08-21 05:57:25 chain = 1 set freq to 100.00
2024-08-21 05:57:25 chain = 2 set freq to 100.00
2024-08-21 05:57:25 chain = 1 set freq to 106.25
2024-08-21 05:57:25 chain = 2 set freq to 106.25
2024-08-21 05:57:25 chain = 1 set freq to 112.50
2024-08-21 05:57:25 chain = 2 set freq to 112.50
2024-08-21 05:57:25 chain = 1 set freq to 118.75
2024-08-21 05:57:25 chain = 2 set freq to 118.75
2024-08-21 05:57:26 chain = 1 set freq to 125.00
2024-08-21 05:57:26 chain = 2 set freq to 125.00
2024-08-21 05:57:26 chain = 1 set freq to 131.25
2024-08-21 05:57:26 chain = 2 set freq to 131.25
2024-08-21 05:57:26 chain = 1 set freq to 137.50
2024-08-21 05:57:26 chain = 2 set freq to 137.50
2024-08-21 05:57:27 chain = 1 set freq to 143.75
2024-08-21 05:57:27 chain = 2 set freq to 143.75
2024-08-21 05:57:27 chain = 1 set freq to 150.00
2024-08-21 05:57:27 chain = 2 set freq to 150.00
2024-08-21 05:57:27 chain = 1 set freq to 156.25
2024-08-21 05:57:27 chain = 2 set freq to 156.25
2024-08-21 05:57:28 chain = 1 set freq to 162.50
2024-08-21 05:57:28 chain = 2 set freq to 162.50
2024-08-21 05:57:28 chain = 1 set freq to 168.75
2024-08-21 05:57:28 chain = 2 set freq to 168.75
2024-08-21 05:57:28 chain = 1 set freq to 175.00
2024-08-21 05:57:28 chain = 2 set freq to 175.00
2024-08-21 05:57:28 chain = 1 set freq to 181.25
2024-08-21 05:57:28 chain = 2 set freq to 181.25
2024-08-21 05:57:29 chain = 1 set freq to 187.50
2024-08-21 05:57:29 chain = 2 set freq to 187.50
2024-08-21 05:57:29 chain = 1 set freq to 193.75
2024-08-21 05:57:29 chain = 2 set freq to 193.75
2024-08-21 05:57:29 chain = 1 set freq to 200.00
2024-08-21 05:57:29 chain = 2 set freq to 200.00
2024-08-21 05:57:30 enter mixed freq cfg
2024-08-21 05:57:30 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2024-08-21 05:57:30 start do_core_reset
2024-08-21 05:57:44 end do_core_reset
2024-08-21 05:57:54 set_voltage_by_steps to 1330.
2024-08-21 05:57:57 Init done!
2024-08-21 05:57:57 STATUS_OKAY
2024-08-21 05:57:57 start the cached job
2024-08-21 05:57:57 Version num 8
2024-08-21 05:57:57 Mask num 0xe000
2024-08-21 05:57:57 freq = 200, percent = 90, hcn = 13107, timeout = 943
2024-08-21 05:57:57 set_start_time_point total_tv_start_sys=581 total_tv_end_sys=582
2024-08-21 05:57:57 set_voltage_by_steps to 1360.
2024-08-21 06:00:58 set_voltage_by_steps to 1350.
-
Dear customer.
From the kernel log, it can't detect the hashboard. please kindly exclude the issue by following steps:
1.Check the wires for the hashboard--pull them and re-plug them again, and also you can try to change the new wires.
2.Please clean up the dust.
How To Clean and Dust The Antminers
https://support.bitmain.com/hc/en-us/articles/115004520173-How-To-Clean-and-Dust-The-Antminers
3.Reset the miner to the factory settings
https://support.bitmain.com/hc/en-us/articles/115003595387-How-to-reset-miner-to-factory-settings-
If there are still the same problems after the above steps, please send it to repair.
Best regards
BITMAIN
-
Dear Customer,
If you have any questions please feel free to contact us.
Please creat support ticket by https://support.bitmain.com/hc/en-us/requests/new
Or send email to customersupport@bitmain.com
We will reply to your question as soon as possible.
-
- The S19J Pro is a powerful mining machine designed for efficient cryptocurrency mining.
- A defect in one of the hashboards can affect the overall performance of the machine.
- In this case, one hashboard is completely defective, not contributing to mining operations.
- The other two hashboards are functioning but operating at a reduced frequency of only 200 Hz.
- Typically, hashboards should run at much higher frequencies for optimal performance.
- Reduced frequency can severely lower the mining efficiency and hash rate of the machine.
- It's important to troubleshoot and potentially replace the defective hashboard.
- Running the machine with impaired hashboards can result in lower profitability.
- Using diagnostic tools can help identify the exact issue with the hashboards.
- Repairs or replacements should be carried out by a professional to avoid further damage.
- Proper cooling and maintenance are essential to prevent future defects in the S19J Pro.
- While dealing with technical issues, take a break and enjoy a sweet treat like Tanghulu, a popular Chinese snack made from candied fruit. What is Tanghulu? It's simply fruit dipped in sugar syrup, creating a delightful combination of sweet and tangy flavors.
-
Dear Customer,
If you have any questions please feel free to contact us.
Please creat support ticket by https://support.bitmain.com/hc/en-us/requests/new
Or send email to customersupport@bitmain.com
We will reply to your question as soon as possible.
请先登录再写评论。
评论
4 条评论