my s19 90th rig occasionally stops mining and now one of the boards is down so I only have 60th
my s19 90th rig occasionally stops mining and now one of the boards is down so I only have 60th
[ 0.000000@0] Booting Linux on physical CPU 0x0 [ 0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Mon Dec 26 17:29:52 CST 2022 [ 0.000000@0] Boot CPU: AArch64 Processor [410fd034] [ 0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '') [ 0.000000@0] bootconsole [aml_uart0] enabled [ 0.000000@0] efi: Getting EFI parameters from FDT: [ 0.000000@0] efi: UEFI not found. [ 0.000000@0] 07400000 - 07500000, 1024 KB, ramoops@0x07400000 [ 0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB [ 0.000000@0] 05000000 - 05400000, 4096 KB, linux,secmon [ 0.000000@0] __reserved_mem_alloc_size, start:0x000000003e000000, end:0x0000000040000000, len:32 MiB [ 0.000000@0] failed to allocate memory for node linux,meson-fb, size:32 MB [ 0.000000@0] cma: Reserved 16 MiB at 0x000000000f000000 [ 0.000000@0] On node 0 totalpages: 65536 [ 0.000000@0] DMA zone: 1024 pages used for memmap [ 0.000000@0] DMA zone: 0 pages reserved [ 0.000000@0] DMA zone: 65536 pages, LIFO batch:15 [ 0.000000@0] psci: probing for conduit method from DT. [ 0.000000@0] psci: PSCIv1.0 detected in firmware. [ 0.000000@0] psci: Using standard PSCI v0.2 function IDs [ 0.000000@0] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000@0] psci: SMC Calling Convention v1.1 [ 0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00ef53000 s64536 r8192 d29672 u102400 [ 0.000000@0] pcpu-alloc: s64536 r8192 d29672 u102400 alloc=25*4096 [ 0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000@0] Detected VIPT I-cache on CPU0 [ 0.000000@0] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64512 [ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 androidboot.rpmb_state=0 rootfstype=ramfs init=/sbin/init [ 0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes) [ 0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.000000@0] Memory: 211688K/262144K available (8764K kernel code, 1194K rwdata, 2424K rodata, 3648K init, 1017K bss, 29976K reserved, 20480K cma-reserved) [ 0.000000@0] Virtual kernel memory layout: [ 0.000000@0] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000@0] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000@0] .text : 0xffffff8009080000 - 0xffffff8009910000 ( 8768 KB) [ 0.000000@0] .rodata : 0xffffff8009910000 - 0xffffff8009b80000 ( 2496 KB) [ 0.000000@0] .init : 0xffffff8009b80000 - 0xffffff8009f10000 ( 3648 KB) [ 0.000000@0] .data : 0xffffff8009f10000 - 0xffffff800a03aa00 ( 1195 KB) [ 0.000000@0] .bss : 0xffffff800a03aa00 - 0xffffff800a139034 ( 1018 KB) [ 0.000000@0] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB) [ 0.000000@0] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000@0] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000@0] 0xffffffbf00000000 - 0xffffffbf00400000 ( 4 MB actual) [ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc010000000 ( 256 MB) [ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000@0] Preemptible hierarchical RCU implementation. [ 0.000000@0] Build-time adjustment of leaf fanout to 64. [ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0 [ 0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized [ 0.000000@0] axg_aoclkc_init: register ao clk ok! [ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk [ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk [ 0.000000@0] axg_amlogic_init_media: register meson media clk [ 0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks [ 0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk [ 0.000000@0] axg_clkc_init initialization complete [ 0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.008252@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194 [ 0.016895@0] Console: colour dummy device 80x25 [ 0.021107@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.031586@0] pid_max: default: 32768 minimum: 301 [ 0.036436@0] thread_stack_cache_init, vmap:ffffffc00e5af600, bitmap:ffffffc00e5a3000, cache page:e5e0 [ 0.045772@0] thread_stack_cache_init, allocation vm area:ffffffc00e5d94c0, addr:ffffff8020000000, size:20001000 [ 0.056005@0] cpu 0, vmap_stack:[ffffffc00ef5c960-ffffffc00ef60950] [ 0.062305@0] cpu 0, irq_stack: [ffffffc00ef53060-ffffffc00ef57050] [ 0.068604@0] cpu 1, vmap_stack:[ffffffc00ef75960-ffffffc00ef79950] [ 0.074904@0] cpu 1, irq_stack: [ffffffc00ef6c060-ffffffc00ef70050] [ 0.081204@0] cpu 2, vmap_stack:[ffffffc00ef8e960-ffffffc00ef92950] [ 0.087504@0] cpu 2, irq_stack: [ffffffc00ef85060-ffffffc00ef89050] [ 0.093804@0] cpu 3, vmap_stack:[ffffffc00efa7960-ffffffc00efab950] [ 0.100104@0] cpu 3, irq_stack: [ffffffc00ef9e060-ffffffc00efa2050] [ 0.106463@0] Security Framework initialized [ 0.110696@0] SELinux: Initializing. [ 0.114387@0] SELinux: Starting in permissive mode [ 0.114422@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes) [ 0.121108@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes) [ 0.128837@0] ftrace: allocating 30061 entries in 118 pages [ 0.186708@0] sched-energy: CPU device node has no sched-energy-costs [ 0.187523@0] CPU0: update cpu_capacity 1024 [ 0.191849@0] ASID allocator initialised with 32768 entries [ 0.229985@0] secmon: can't fine clear_range [ 0.230191@0] EFI services will not be available. [ 0.233453@0] Meson chip version = RevC (25:C - 23:0) [ 0.267124@1] Detected VIPT I-cache on CPU1 [ 0.267185@1] CPU1: update cpu_capacity 1024 [ 0.267187@1] CPU1: Booted secondary processor [410fd034] [ 0.295185@2] Detected VIPT I-cache on CPU2 [ 0.295237@2] CPU2: update cpu_capacity 1024 [ 0.295240@2] CPU2: Booted secondary processor [410fd034] [ 0.323246@3] Detected VIPT I-cache on CPU3 [ 0.323296@3] CPU3: update cpu_capacity 1024 [ 0.323298@3] CPU3: Booted secondary processor [410fd034] [ 0.323387@0] Brought up 4 CPUs [ 0.362609@0] SMP: Total of 4 processors activated. [ 0.367518@0] CPU features: detected feature: 32-bit EL0 Support [ 0.373554@0] CPU features: detected feature: Kernel page table isolation (KPTI) [ 0.384109@0] CPU: All CPU(s) started at EL2 [ 0.385294@0] alternatives: patching kernel code [ 0.390596@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755 [ 0.397814@0] devtmpfs: initialized [ 0.412891@0] DMI not present or invalid. [ 0.413281@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.421258@0] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.427830@0] pinctrl core: initialized pinctrl subsystem [ 0.434217@0] NET: Registered protocol family 16 [ 0.461763@0] cpuidle: using governor menu [ 0.462269@0] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000) [ 0.467878@0] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers. [ 0.475280@3] DMA: preallocated 256 KiB pool for atomic allocations [ 0.481391@3] clkmsr: clkmsr: driver init [ 0.485491@3] aml_watch_point_probe, in, wp:2 [ 0.490906@3] pstore: using zlib compression [ 0.494320@3] console [pstore-1] enabled [ 0.497753@3] pstore: Registered ramoops as persistent store backend [ 0.504157@3] ramoops: attached 0x100000@0x7400000, ecc: 0/0 [ 0.518510@3] aml_iomap: amlogic iomap probe done [ 0.525429@3] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c [ 0.527353@3] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0 [ 0.616777@3] usbcore: registered new interface driver usbfs [ 0.616950@3] usbcore: registered new interface driver hub [ 0.622549@3] usbcore: registered new device driver usb [ 0.627857@3] pps_core: LinuxPPS API ver. 1 registered [ 0.632780@3] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.642195@3] PTP clock support registered [ 0.646516@3] dmi: Firmware registration failed. [ 0.651520@3] secmon: reserve_mem_size:0x300000 [ 0.655546@3] secmon secmon: assigned reserved memory node linux,secmon [ 0.662441@3] secmon: get page:ffffffbf00140000, 5000 [ 0.667160@3] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000 [ 0.675548@3] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000 [ 0.683427@3] NetLabel: Initializing [ 0.685592@3] NetLabel: domain hash size = 128 [ 0.690168@3] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.695416@3] NetLabel: unlabeled traffic allowed by default [ 0.702041@3] clocksource: Switched to clocksource arch_sys_counter [ 0.828687@3] VFS: Disk quotas dquot_6.6.0 [ 0.828832@3] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.855035@2] NET: Registered protocol family 2 [ 0.856082@2] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.861262@2] TCP bind hash table entries: 2048 (order: 3, 32768 bytes) [ 0.867998@2] TCP: Hash tables configured (established 2048 bind 2048) [ 0.874517@2] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.880483@2] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.887227@2] NET: Registered protocol family 1 [ 0.892188@2] RPC: Registered named UNIX socket transport module. [ 0.897629@2] RPC: Registered udp transport module. [ 0.902507@2] RPC: Registered tcp transport module. [ 0.907401@2] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.916565@2] Unpacking initramfs... [ 1.416770@2] Initramfs unpacking failed: junk in compressed archive [ 1.423580@2] Freeing initrd memory: 6572K [ 1.424511@2] hw perfevents: clusterb_enabled = 0 [ 1.426817@2] hw perfevents: cpumasks 0xf, 0x0 [ 1.431352@2] hw perfevents: cluster A irq = 7 [ 1.435866@2] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.445932@2] audit: initializing netlink subsys (disabled) [ 1.449391@2] audit: type=2000 audit(1.304:1): initialized [ 1.460700@2] workingset: timestamp_bits=62 max_order=16 bucket_order=0 [ 1.481072@2] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.484058@2] NFS: Registering the id_resolver key type [ 1.486789@2] Key type id_resolver registered [ 1.491115@2] Key type id_legacy registered [ 1.495741@2] fuse init (API version 7.26) [ 1.501097@2] SELinux: Registering netfilter hooks [ 1.507271@2] NET: Registered protocol family 38 [ 1.507333@2] Key type asymmetric registered [ 1.510576@2] Asymmetric key parser 'x509' registered [ 1.516057@2] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.523282@2] io scheduler noop registered (default) [ 1.528276@2] io scheduler deadline registered [ 1.533046@2] io scheduler cfq registered [ 1.553435@3] random: fast init done [ 1.553534@3] random: crng init done [ 1.553996@2] Unable to detect cache hierarchy for CPU 0 [ 1.590437@2] loop: module loaded [ 1.595939@2] zram: Added device: zram0 [ 1.596372@2] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.601486@2] libphy: Fixed MDIO Bus: probed [ 1.606010@2] tun: Universal TUN/TAP device driver, 1.6 [ 1.610349@2] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.618606@2] ee eth reset:Addr = ffffff80081fd008 [ 1.625993@2] meson6-dwmac ff3f0000.ethernet: no reset control found [ 1.628038@2] stmmac - user ID: 0x11, Synopsys ID: 0x37 [ 1.633274@2] Ring mode enabled [ 1.636499@2] DMA HW capability register supported [ 1.641232@2] Normal descriptors [ 1.644548@2] RX Checksum Offload Engine supported [ 1.649455@2] COE Type 2 [ 1.652072@2] TX Checksum insertion supported [ 1.656542@2] Wake-Up On Lan supported [ 1.660478@2] Enable RX Mitigation via HW Watchdog Timer [ 1.673999@2] libphy: stmmac: probed [ 1.674090@2] eth%d: PHY ID 0007c0f1 at 0 IRQ POLL (stmmac-0:00) active [ 1.680496@2] PPP generic driver version 2.4.2 [ 1.683469@2] PPP BSD Compression module registered [ 1.687990@2] PPP Deflate Compression module registered [ 1.693231@2] PPP MPPE Compression module registered [ 1.698197@2] NET: Registered protocol family 24 [ 1.703688@2] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.709596@2] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.716646@2] usbcore: registered new interface driver cdc_acm [ 1.721839@2] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.730267@2] usbcore: registered new interface driver usbserial [ 1.736934@2] mousedev: PS/2 mouse device common for all mice [ 1.742401@2] usbcore: registered new interface driver xpad [ 1.747790@2] i2c /dev entries driver [ 1.752544@2] cpu cpu0: bL_cpufreq_init: CPU 0 initialized [ 1.756806@2] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi [ 1.767776@2] ff803000.serial: clock gate not found [ 1.769308@2] meson_uart ff803000.serial: ==uart0 reg addr = ffffff800830d000 [ 1.776536@2] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 13, base_baud = 1500000) is a meson_uart [ 1.791458@2] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200 [ 1.794161@2] console [ttyS0] enabled [ 1.801377@2] bootconsole [aml_uart0] disabled [ 1.811046@1] ff804000.serial: clock gate not found [ 1.815167@1] meson_uart ff804000.serial: ==uart3 reg addr = ffffff8008321000 [ 1.822272@1] ff804000.serial: ttyS3 at MMIO 0xff804000 (irq = 14, base_baud = 1500000) is a meson_uart [ 1.832622@0] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff8008323000 [ 1.838793@0] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 25, base_baud = 1500000) is a meson_uart [ 1.848964@2] meson_uart ffd23000.serial: ==uart2 reg addr = ffffff8008325000 [ 1.855259@2] ffd23000.serial: ttyS2 at MMIO 0xffd23000 (irq = 26, base_baud = 1500000) is a meson_uart [ 1.866232@1] amlogic-new-usb2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff8008348000 [ 1.875509@1] amlogic-new-usb3 ffe09080.usb3phy: This phy has no usb port [ 1.881996@1] amlogic-new-usb3 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff800834c080 [ 1.896952@0] i2c i2c-1: of_i2c: modalias failure on /soc/aobus@ff800000/i2c@5000/mcu6350@40 [ 1.900818@0] i2c i2c-1: Failed to create I2C device for /soc/aobus@ff800000/i2c@5000/mcu6350@40 [ 1.913172@0] aml_dma ff63e000.aml_dma: Aml dma [ 1.916305@0] aml_aes_dma ff63e000.aml_dma:aml_aes: Aml AES_dma [ 1.921332@0] aml_sha_dma ff63e000.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma [ 1.927680@0] efusekeynum: 4 [ 1.930003@0] efusekeyname: mac offset: 0 size: 6 [ 1.936454@0] efusekeyname: mac_bt offset: 6 size: 6 [ 1.942857@0] efusekeyname: mac_wifi offset: 12 size: 6 [ 1.949279@0] efusekeyname: usid offset: 18 size: 16 [ 1.956099@2] efuse efuse: probe OK! [ 1.961517@2] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller [ 1.968767@2] meson-mmc: >>>>>>>>hostbase ffffff8008358000, dmode [ 1.973904@2] meson-mmc: actual_clock :400000, HHI_nand: 0x80 [ 1.979078@2] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c [ 2.026150@2] meson-mmc: meson_mmc_probe() : success! [ 2.026399@2] amlogic mtd driver init [ 2.030482@2] prase_get_dtb_nand_parameter:128,parse dts start [ 2.035216@2] bl mode descrete [ 2.038095@2] fip_copies 4 [ 2.040759@2] fip_size 0x200000 [ 2.043898@2] nand_clk_ctrl 0xffe07000 [ 2.047622@2] prase_get_dtb_nand_parameter:234,parse dts end [ 2.053289@2] nand_clk_ctrl 0xffe07000 [ 2.057011@2] nand register base ffffff80083df800, nand clock register ffffff80083e1000 [ 2.065751@2] plat->aml_nand_device ffffff800a005c10 [ 2.069917@2] m3_nand_probe() aml_nand_device ffffff800a005c10 [ 2.075980@2] NAND device id: 2c da 90 95 6 0 [ 2.080046@2] NAND device: Manufacturer ID: [ 2.084112@2] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A) [ 2.091154@2] oob_fill_cnt =32 oob_size =64, bch_bytes =14 [ 2.096588@2] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16 [ 2.102136@2] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1 [ 2.108382@2] mtd->oobavail: 0x8 [ 2.111781@2] aml_nand_init 2119: plat-name:bootloader [ 2.116701@2] Creating 1 MTD partitions on "bootloader": [ 2.121988@2] 0x000000000000-0x000000200000 : "bootloader" [ 2.131182@0] bootloader initialized ok [ 2.131251@0] plat->aml_nand_device ffffff800a005c10 [ 2.136235@0] m3_nand_probe() aml_nand_device ffffff800a005c10 [ 2.142385@0] NAND device id: 2c da 90 95 6 0 [ 2.146346@0] NAND device: Manufacturer ID: [ 2.150421@0] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A) [ 2.157456@0] oob_fill_cnt =32 oob_size =64, bch_bytes =14 [ 2.162896@0] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16 [ 2.168436@0] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1 [ 2.174689@0] mtd->oobavail: 0x8 [ 2.178157@0] aml_nand_init 2119: plat-name:nandnormal [ 2.183057@0] bbt_start=20 [ 2.185662@0] env_start=24 [ 2.188370@0] key_start=32 [ 2.191054@0] dtb_start=40 [ 2.193722@0] ddr_start=44 [ 2.196428@0] nbbt: info size=0x800 max_scan_blk=24, start_blk=20 [ 2.202921@0] get_free_node 43: bitmap=0 [ 2.206397@0] get_free_node 55: bitmap=1 [ 2.210488@0] get_free_node 43: bitmap=1 [ 2.214195@0] get_free_node 55: bitmap=3 [ 2.218286@0] get_free_node 43: bitmap=3 [ 2.221977@0] get_free_node 55: bitmap=7 [ 2.225897@0] nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1 [ 2.232567@0] nbbt free list: [ 2.235514@0] blockN=21, ec=-1, dirty_flag=0 [ 2.239760@0] blockN=22, ec=-1, dirty_flag=0 [ 2.244007@0] blockN=23, ec=-1, dirty_flag=0 [ 2.248255@0] aml_nand_scan_rsv_info 1141: page_num=1 [ 2.253663@0] nbbt valid addr: 280000 [ 2.256922@0] aml_nand_bbt_check 1306 bbt is valid, reading. [ 2.262556@0] aml_nand_read_rsv_info:423,read nbbt info at 280000 [ 2.268816@0] nenv: info size=0x10000 max_scan_blk=32, start_blk=24 [ 2.275242@0] get_free_node 43: bitmap=7 [ 2.278761@0] get_free_node 55: bitmap=f [ 2.282852@0] get_free_node 43: bitmap=f [ 2.286562@0] get_free_node 55: bitmap=1f [ 2.290739@0] get_free_node 43: bitmap=1f [ 2.294535@0] get_free_node 55: bitmap=3f [ 2.298712@0] get_free_node 43: bitmap=3f [ 2.302508@0] get_free_node 55: bitmap=7f [ 2.306686@0] get_free_node 43: bitmap=7f [ 2.310482@0] get_free_node 55: bitmap=ff [ 2.314659@0] get_free_node 43: bitmap=ff [ 2.318455@0] get_free_node 55: bitmap=1ff [ 2.322719@0] get_free_node 43: bitmap=1ff [ 2.326602@0] get_free_node 55: bitmap=3ff [ 2.330675@0] nenv : phy_blk_addr=24, ec=0, phy_page_addr=0, timestamp=1 [ 2.337345@0] nenv free list: [ 2.340293@0] blockN=25, ec=-1, dirty_flag=0 [ 2.344540@0] blockN=26, ec=-1, dirty_flag=0 [ 2.348786@0] blockN=27, ec=-1, dirty_flag=0 [ 2.353033@0] blockN=28, ec=-1, dirty_flag=0 [ 2.357280@0] blockN=29, ec=-1, dirty_flag=0 [ 2.361526@0] blockN=30, ec=-1, dirty_flag=0 [ 2.365773@0] blockN=31, ec=-1, dirty_flag=0 [ 2.370035@0] aml_nand_scan_rsv_info 1141: page_num=32 [ 2.387228@0] nenv valid addr: 310000 [ 2.387261@0] nkey: info size=0x8000 max_scan_blk=40, start_blk=32 [ 2.391621@0] get_free_node 43: bitmap=3ff [ 2.395502@0] get_free_node 55: bitmap=7ff [ 2.399766@0] get_free_node 43: bitmap=7ff [ 2.403647@0] get_free_node 55: bitmap=fff [ 2.407912@0] get_free_node 43: bitmap=fff [ 2.411795@0] get_free_node 55: bitmap=1fff [ 2.416145@0] get_free_node 43: bitmap=1fff [ 2.420115@0] get_free_node 55: bitmap=3fff [ 2.424466@0] get_free_node 43: bitmap=3fff [ 2.428435@0] get_free_node 55: bitmap=7fff [ 2.432786@0] get_free_node 43: bitmap=7fff [ 2.436755@0] get_free_node 55: bitmap=ffff [ 2.441105@0] get_free_node 43: bitmap=ffff [ 2.445075@0] get_free_node 55: bitmap=1ffff [ 2.449513@0] get_free_node 43: bitmap=1ffff [ 2.453568@0] get_free_node 55: bitmap=3ffff [ 2.457815@0] nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0 [ 2.464486@0] nkey free list: [ 2.467433@0] blockN=32, ec=-1, dirty_flag=0 [ 2.471680@0] blockN=33, ec=-1, dirty_flag=0 [ 2.475926@0] blockN=34, ec=-1, dirty_flag=0 [ 2.480173@0] blockN=35, ec=-1, dirty_flag=0 [ 2.484419@0] blockN=36, ec=-1, dirty_flag=0 [ 2.488666@0] blockN=37, ec=-1, dirty_flag=0 [ 2.492912@0] blockN=38, ec=-1, dirty_flag=0 [ 2.497160@0] blockN=39, ec=-1, dirty_flag=0 [ 2.501406@0] aml_nand_scan_rsv_info 1141: page_num=16 [ 2.506520@0] nkey valid addr: fffffffffffe0000 [ 2.511027@0] aml_nand_key_check 1251 NO key exist [ 2.515794@0] ndtb: info size=0x20000 max_scan_blk=44, start_blk=40 [ 2.522425@0] get_free_node 43: bitmap=3ffff [ 2.526282@0] get_free_node 55: bitmap=7ffff [ 2.530719@0] get_free_node 43: bitmap=7ffff [ 2.534775@0] get_free_node 55: bitmap=fffff [ 2.539211@0] get_free_node 43: bitmap=fffff [ 2.543268@0] get_free_node 55: bitmap=1fffff [ 2.547601@0] ndtb : phy_blk_addr=40, ec=0, phy_page_addr=0, timestamp=1 [ 2.554272@0] ndtb free list: [ 2.557203@0] blockN=41, ec=-1, dirty_flag=0 [ 2.561467@0] blockN=42, ec=-1, dirty_flag=0 [ 2.565713@0] blockN=43, ec=-1, dirty_flag=0 [ 2.569960@0] aml_nand_scan_rsv_info 1141: page_num=64 [ 2.587172@0] ndtb valid addr: 500000 [ 2.587206@0] nddr: info size=0x20000 max_scan_blk=46, start_blk=44 [ 2.591655@0] get_free_node 43: bitmap=1fffff [ 2.595797@0] get_free_node 55: bitmap=3fffff [ 2.600321@0] get_free_node 43: bitmap=3fffff [ 2.604464@0] get_free_node 55: bitmap=7fffff [ 2.608797@0] nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0 [ 2.615467@0] nddr free list: [ 2.618415@0] blockN=44, ec=-1, dirty_flag=0 [ 2.622661@0] blockN=45, ec=-1, dirty_flag=0 [ 2.626909@0] aml_nand_scan_rsv_info 1141: page_num=64 [ 2.632022@0] nddr valid addr: fffffffffffe0000 [ 2.636528@0] aml_nand_ddr_check 1281 NO ddr exist [ 2.641298@0] tpl: off 8388608, size 8388608 [ 2.772727@0] Creating 6 MTD partitions on "nandnormal": [ 2.772774@0] 0x000000800000-0x000001000000 : "tpl" [ 2.784311@0] 0x000001000000-0x000001200000 : "misc" [ 2.787555@1] 0x000001200000-0x000002200000 : "recovery" [ 2.799717@1] 0x000002200000-0x000004200000 : "boot" [ 2.818889@3] 0x000004200000-0x000004700000 : "config" [ 2.827588@1] 0x000004700000-0x000010000000 : "nvdata" [ 2.928501@2] nandnormal initialized ok [ 2.928614@2] aml_ubootenv_init: register env chardev [ 2.932130@2] aml_ubootenv_init: register env chardev OK [ 2.937182@2] amlnf_dtb_init: register dtb cdev [ 2.941908@3] amlnf_dtb_init: register dtd cdev OK [ 2.946364@3] mtd_nand_probe 267 , err = 0 [ 2.951490@2] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc0 [ 2.957013@2] input: aml_vkeypad as /devices/platform/rtc/input/input0 [ 2.963913@3] unifykey: storage in base: 0xffffffc005000000 [ 2.968539@3] unifykey: storage out base: 0xffffffc005040000 [ 2.974152@3] unifykey: storage block base: 0xffffffc005080000 [ 2.979945@3] unifykey: probe done! [ 2.984152@3] unifykey: no efuse-version set, use default value: -1 [ 2.989669@3] unifykey: key unify config unifykey-num is 6 [ 2.995216@3] unifykey: key unify fact unifykey-num is 6 [ 3.000404@3] unifykey: unifykey_devno: f200000 [ 3.005391@0] unifykey: device unifykeys created ok [ 3.009910@0] unifykey: aml_unifykeys_init done! [ 3.014791@0] sysled: module init [ 3.018271@0] meson_wdt ffd0f0d0.watchdog: start watchdog [ 3.023044@0] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog [ 3.030481@1] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done [ 3.039172@2] dmc_monitor_probe [ 3.040850@2] defendkey defendkey: Reserved memory is not enough! [ 3.045781@2] defendkey: probe of defendkey failed with error -22 [ 3.052100@2] GACT probability NOT on [ 3.055488@2] Mirror/redirect action on [ 3.059265@2] u32 classifier [ 3.062108@2] Actions configured [ 3.065649@2] Netfilter messages via NETLINK v0.30. [ 3.070948@2] nf_conntrack version 0.5.0 (2048 buckets, 8192 max) [ 3.077177@2] ctnetlink v0.93: registering with nfnetlink. [ 3.082995@0] xt_time: kernel timezone is -0000 [ 3.086732@0] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 3.093353@0] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.098090@0] arp_tables: arp_tables: (C) 2002 David S. Miller [ 3.103527@0] Initializing XFRM netlink socket [ 3.109043@0] NET: Registered protocol family 10 [ 3.114805@0] mip6: Mobile IPv6 [ 3.115613@0] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 3.121583@0] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.129567@0] NET: Registered protocol family 17 [ 3.131866@0] NET: Registered protocol family 15 [ 3.136465@0] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 3.149600@0] l2tp_core: L2TP core driver, V2.0 [ 3.153998@0] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 3.158916@0] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 3.164671@0] l2tp_netlink: L2TP netlink interface [ 3.169462@0] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 3.175540@0] l2tp_debugfs: L2TP debugfs support [ 3.180063@0] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 3.186748@0] NET: Registered protocol family 35 [ 3.191642@0] Key type dns_resolver registered [ 3.196236@0] Registered swp emulation handler [ 3.200192@0] Registered cp15_barrier emulation handler [ 3.205295@0] Registered setend emulation handler [ 3.210055@0] disable EAS feature [ 3.214719@0] registered taskstats version 1 [ 3.231295@1] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host [ 3.737754@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.737844@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 3.746160@1] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f664 hci version 0x100 quirks 0x02010010 [ 3.754565@1] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0xff500000 [ 3.762223@0] hub 1-0:1.0: USB hub found [ 3.764465@0] hub 1-0:1.0: 1 port detected [ 3.769160@0] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.774149@0] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 3.782066@0] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.791645@1] hub 2-0:1.0: USB hub found [ 3.794158@1] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 3.801424@1] usb usb2: Unsupported the hub [ 3.806251@1] aml_vrtc rtc: setting system clock to 2023-11-20 06:05:36 UTC (1700460336) [ 3.814279@1] dwc_otg ff400000.dwc2_a: dwc_otg_driver_probe(ffffffc00d173800) [ 3.814356@1] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0 [ 3.822248@1] dwc_otg ff400000.dwc2_a: base=0xffffff8008580000 [ 3.822261@1] dwc_otg ff400000.dwc2_a: dwc_otg_device=0xffffffc00bb12600 [ 3.923054@1] dwc_otg: Core Release: 3.10a [ 3.923108@1] dwc_otg: Setting default values for core params [ 3.927304@1] dwc_otg: curmode: 0, host_only: 0 [ 3.931805@1] dwc_otg ff400000.dwc2_a: DMA config: BURST_DEFAULT [ 3.944320@1] dwc_otg: Using Buffer DMA mode [ 3.944358@1] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1 [ 3.948326@1] dwc_otg: Working on port type = SLAVE [ 3.953124@1] dwc_otg: Dedicated Tx FIFOs mode [ 3.960096@1] thermal thermal_zone0: binding zone soc_thermal with cdev thermal-cpufreq-0 failed:-22 [ 3.966841@1] cpucore_cooling_register, max_cpu_core_num:4 [ 3.978959@0] gxbb_pm: enter meson_pm_probe! [ 3.979017@0] no vddio3v3_en pin [ 3.980670@0] pm-meson aml_pm: Can't get switch_clk81 [ 3.985774@0] gxbb_pm: meson_pm_probe done [ 3.990745@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200 [ 3.997009@0] Freeing unused kernel memory: 3648K [ 4.011003@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200 [ 4.261912@0] ubi0: attaching mtd5 [ 4.280554@0] ubi0: scanning is finished [ 4.285301@1] ubi0: attached mtd5 (name "config", size 5 MiB) [ 4.285433@1] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.292486@1] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.299408@1] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.306503@1] ubi0: good PEBs: 40, bad PEBs: 0, corrupted PEBs: 0 [ 4.312582@1] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 4.319944@1] ubi0: max/mean erase counter: 21/11, WL threshold: 4096, image sequence number: 1754666939 [ 4.329391@1] ubi0: available PEBs: 0, total reserved PEBs: 40, PEBs reserved for bad PEB handling: 4 [ 4.338595@0] ubi0: background thread "ubi_bgt0d" started, PID 1076 [ 4.351783@2] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 1080 [ 4.381168@3] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "config_data" [ 4.383587@3] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 4.393630@3] UBIFS (ubi0:0): FS size: 2793472 bytes (2 MiB, 22 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) [ 4.403843@3] UBIFS (ubi0:0): reserved for root: 131942 bytes (128 KiB) [ 4.410440@3] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 8E122A9C-1D4F-461A-ABF5-042222922F5A, small LPT model [ 4.435080@0] ubi2: attaching mtd6 [ 5.108943@0] ubi2: scanning is finished [ 5.116259@1] ubi2: attached mtd6 (name "nvdata", size 185 MiB) [ 5.116558@1] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 5.123668@1] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 5.130533@1] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 5.137630@1] ubi2: good PEBs: 1480, bad PEBs: 0, corrupted PEBs: 0 [ 5.143868@1] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 5.151235@1] ubi2: max/mean erase counter: 32/6, WL threshold: 4096, image sequence number: 4159432726 [ 5.160602@1] ubi2: available PEBs: 0, total reserved PEBs: 1480, PEBs reserved for bad PEB handling: 4 [ 5.169977@2] ubi2: background thread "ubi_bgt2d" started, PID 1087 [ 5.182862@3] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 1091 [ 5.225785@0] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "nvdata_data" [ 5.228215@0] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 5.238239@0] UBIFS (ubi2:0): FS size: 185384960 bytes (176 MiB, 1460 LEBs), journal size 9269248 bytes (8 MiB, 73 LEBs) [ 5.249064@0] UBIFS (ubi2:0): reserved for root: 4952683 bytes (4836 KiB) [ 5.255827@0] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID 254949E2-F598-4597-8493-4AA9AF646165, small LPT model [ 5.482874@2] eth0: device MAC address 02:5c:0e:ed:c4:46 [ 5.566952@1] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP. [ 5.568246@1] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 5.815736@1] uart_trans: loading out-of-tree module taints kernel. [ 5.818336@1] register uart_trans chrdev success. [ 5.821466@1] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 0 to 9600 [ 5.829186@1] tty port open success [/dev/ttyS3]! [ 5.833887@1] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 9600 to 115200 [ 5.842206@1] init sucess for tty struct (246:3) [/dev/ttyS3] [ 5.848509@1] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 0 to 9600 [ 5.856020@1] tty port open success [/dev/ttyS2]! [ 5.860671@1] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 9600 to 115200 [ 5.869078@1] init sucess for tty struct (246:2) [/dev/ttyS2] [ 5.875206@1] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 0 to 9600 [ 5.882842@1] tty port open success [/dev/ttyS1]! [ 5.887561@1] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 115200 [ 5.895930@1] init sucess for tty struct (246:1) [/dev/ttyS1] [ 5.906150@1] create workqueue success! [ 7.594401@1] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 7.597686@1] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 26.859958@1] uart trans dev open. [ 26.860069@1] uart_buf virt addr = 0xffffffc00b180000 [ 26.862844@1] uart_buf phys addr = 0x0b180000 [ 26.867129@1] uart_buf pfn = 0x0000b180 [ 26.871863@1] uart trans stop send work timer. [ 26.876073@1] uart trans set chain exist bits:0x7. [ 26.880687@1] uart trans set work queue count 768. [ 228.640044@2] uart set baud to: 4098 [ 228.640106@2] uart set baud to: 4098 [ 228.641567@2] uart set baud to: 4098 [ 289.780141@3] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 115200 to 3000000 [ 289.783309@3] uart set baud to: 4109 [ 289.847365@3] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 115200 to 3000000 [ 289.850501@3] uart set baud to: 4109 [ 351.944251@0] nf_conntrack: default automatic helper assignment has been turned off for security reasons and CT-based firewall rule not found. Use the iptables CT target to attach helpers instead. [ 352.159283@3] uart trans start send work timer. ===========================================Miner log=========================================== 2023-11-20 06:05:43 Open miner sn file /config/sn error 2023-11-20 06:05:43 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX sn : 2023-11-20 06:05:44 This is fix-freq version 2023-11-20 06:05:44 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX 2023-11-20 06:05:44 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 17:22:17 2023-11-20 06:05:44 opt_multi_version = 1 2023-11-20 06:05:44 opt_bitmain_ab = 1 2023-11-20 06:05:44 mid_auto_gen = 1 2023-11-20 06:05:44 opt_bitmain_work_mode = 0 2023-11-20 06:05:44 port 439 already exported 2023-11-20 06:05:44 port 454 already exported 2023-11-20 06:05:44 port 440 already exported 2023-11-20 06:05:44 port 455 already exported 2023-11-20 06:05:44 port 441 already exported 2023-11-20 06:05:44 port 456 already exported 2023-11-20 06:05:44 port 438 already exported 2023-11-20 06:05:44 port 453 already exported 2023-11-20 06:05:44 port 446 already exported 2023-11-20 06:05:44 port 445 already exported 2023-11-20 06:05:44 Note: front fan is power on! 2023-11-20 06:05:44 Note: rear fan is power on! 2023-11-20 06:05:44 start the http log. 2023-11-20 06:05:44 httpListenThread start ret=0 2023-11-20 06:05:44 start listen on 6060 ... 2023-11-20 06:05:44 bad chain id = 3 2023-11-20 06:05:47 bad chain id = 3 2023-11-20 06:05:49 ==========================capability start========================== 2023-11-20 06:05:49 board num = 3 2023-11-20 06:05:49 board id = 0, chain num = 1 2023-11-20 06:05:49 chain id = 0 2023-11-20 06:05:49 board id = 1, chain num = 1 2023-11-20 06:05:49 chain id = 1 2023-11-20 06:05:49 board id = 2, chain num = 1 2023-11-20 06:05:49 chain id = 2 2023-11-20 06:05:49 ==========================capability end============================ 2023-11-20 06:05:49 chain num = 3 2023-11-20 06:05:49 skip loading levels for now 2023-11-20 06:05:53 load chain 0 eeprom data 2023-11-20 06:05:56 load chain 1 eeprom data 2023-11-20 06:05:59 load chain 2 eeprom data 2023-11-20 06:05:59 miner type: Antminer S19 2023-11-20 06:05:59 multi machine mode 2023-11-20 06:05:59 load machine BHB42801 conf 2023-11-20 06:05:59 machine : BHB42801 2023-11-20 06:05:59 chain_num 4, chain_domain_num 44, chain_asic_num 88, domain_asic_num 2 2023-11-20 06:05:59 abandon mix board! 2023-11-20 06:05:59 abandon mix board! 2023-11-20 06:05:59 fan_eft : 0 fan_pwm : 100 2023-11-20 06:05:59 create thread get_nonce_and_register_thread 2023-11-20 06:05:59 fixed working voltage = 1580 2023-11-20 06:05:59 fixed frequency is 675 2023-11-20 06:05:59 Chain [0] PCB Version: 0x0110 2023-11-20 06:05:59 Chain [0] BOM Version: 0x0010 2023-11-20 06:05:59 Chain [1] PCB Version: 0x0110 2023-11-20 06:05:59 Chain [1] BOM Version: 0x0010 2023-11-20 06:05:59 Chain [2] PCB Version: 0x0110 2023-11-20 06:05:59 Chain [2] BOM Version: 0x0010 2023-11-20 06:05:59 bad chain id = 3 2023-11-20 06:05:59 Fan check passed. 2023-11-20 06:05:59 uart_trans addr:0xf6e14000. 2023-11-20 06:06:00 chain[0] PIC jump to app 2023-11-20 06:06:02 Check chain[0] PIC fw version=0x89 2023-11-20 06:06:03 chain[1] PIC jump to app 2023-11-20 06:06:04 Check chain[1] PIC fw version=0x89 2023-11-20 06:06:05 chain[2] PIC jump to app 2023-11-20 06:06:07 Check chain[2] PIC fw version=0x89 2023-11-20 06:06:07 create thread pic_heart_beat_thread 2023-11-20 06:06:07 max sensor num = 4 2023-11-20 06:06:07 STATUS_INITED: soc init done! 2023-11-20 06:06:07 temperature_monitor_thread start... 2023-11-20 06:06:11 start to init... 2023-11-20 06:06:11 i2c_sim_init start 2023-11-20 06:06:11 init gpio477 2023-11-20 06:06:11 init gpio476 2023-11-20 06:06:11 i2c_sim_init end 2023-11-20 06:06:12 power open power_version = 0x73 2023-11-20 06:06:15 power is not Calibrated 2023-11-20 06:06:15 warning:power is not calibration. 2023-11-20 06:06:16 power type version: 0x0073 2023-11-20 06:06:16 Initializing the power, please wait, this may take up to 2 minutes... 2023-11-20 06:09:17 Slept 180 seconds, diff = 4. 2023-11-20 06:09:17 set_voltage_by_steps to 1700. 2023-11-20 06:09:20 chain avg vol rise to 16.93 2023-11-20 06:09:21 start up min temp by 75a = 25 2023-11-20 06:09:31 Chain[0]: find 88 asic, times 0 2023-11-20 06:09:41 Chain[1]: find 88 asic, times 0 2023-11-20 06:09:51 Chain[2]: find 0 asic, times 0 2023-11-20 06:10:02 Chain[2]: find 0 asic, times 1 2023-11-20 06:10:13 Chain[2]: find 0 asic, times 2 2023-11-20 06:10:14 Chain 2 only find 0 asic, will power off hash board 2 2023-11-20 06:10:19 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1 2023-11-20 06:10:22 Bring up temperature is 28 2023-11-20 06:10:22 set UART baud to 3000000 2023-11-20 06:10:22 create thread check_miner_status_thread 2023-11-20 06:10:22 create thread check_system_work_thread 2023-11-20 06:10:22 set_voltage_by_steps to 1650. 2023-11-20 06:10:25 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1 2023-11-20 06:10:25 start do_core_reset 2023-11-20 06:10:34 end do_core_reset 2023-11-20 06:10:34 chain[0] min = 675 max =675 2023-11-20 06:10:34 chain[1] min = 675 max =675 2023-11-20 06:10:34 1.inc all chain freq to 675 2023-11-20 06:10:34 fixed step freq_start = 50, freq_end = 675, freq_step = 6.25 2023-11-20 06:10:34 chain = 0 set freq to 56.25 2023-11-20 06:10:34 chain = 1 set freq to 56.25 2023-11-20 06:10:34 chain = 0 set freq to 62.50 2023-11-20 06:10:34 chain = 1 set freq to 62.50 2023-11-20 06:10:34 chain = 0 set freq to 68.75 2023-11-20 06:10:34 chain = 1 set freq to 68.75 2023-11-20 06:10:35 chain = 0 set freq to 75.00 2023-11-20 06:10:35 chain = 1 set freq to 75.00 2023-11-20 06:10:35 chain = 0 set freq to 81.25 2023-11-20 06:10:35 chain = 1 set freq to 81.25 2023-11-20 06:10:35 chain = 0 set freq to 87.50 2023-11-20 06:10:35 chain = 1 set freq to 87.50 2023-11-20 06:10:36 chain = 0 set freq to 93.75 2023-11-20 06:10:36 chain = 1 set freq to 93.75 2023-11-20 06:10:36 chain = 0 set freq to 100.00 2023-11-20 06:10:36 chain = 1 set freq to 100.00 2023-11-20 06:10:36 chain = 0 set freq to 106.25 2023-11-20 06:10:36 chain = 1 set freq to 106.25 2023-11-20 06:10:36 chain = 0 set freq to 112.50 2023-11-20 06:10:36 chain = 1 set freq to 112.50 2023-11-20 06:10:37 chain = 0 set freq to 118.75 2023-11-20 06:10:37 chain = 1 set freq to 118.75 2023-11-20 06:10:37 chain = 0 set freq to 125.00 2023-11-20 06:10:37 chain = 1 set freq to 125.00 2023-11-20 06:10:37 chain = 0 set freq to 131.25 2023-11-20 06:10:37 chain = 1 set freq to 131.25 2023-11-20 06:10:38 chain = 0 set freq to 137.50 2023-11-20 06:10:38 chain = 1 set freq to 137.50 2023-11-20 06:10:38 chain = 0 set freq to 143.75 2023-11-20 06:10:38 chain = 1 set freq to 143.75 2023-11-20 06:10:38 chain = 0 set freq to 150.00 2023-11-20 06:10:38 chain = 1 set freq to 150.00 2023-11-20 06:10:39 chain = 0 set freq to 156.25 2023-11-20 06:10:39 chain = 1 set freq to 156.25 2023-11-20 06:10:39 chain = 0 set freq to 162.50 2023-11-20 06:10:39 chain = 1 set freq to 162.50 2023-11-20 06:10:39 chain = 0 set freq to 168.75 2023-11-20 06:10:39 chain = 1 set freq to 168.75 2023-11-20 06:10:39 chain = 0 set freq to 175.00 2023-11-20 06:10:39 chain = 1 set freq to 175.00 2023-11-20 06:10:40 chain = 0 set freq to 181.25 2023-11-20 06:10:40 chain = 1 set freq to 181.25 2023-11-20 06:10:40 chain = 0 set freq to 187.50 2023-11-20 06:10:40 chain = 1 set freq to 187.50 2023-11-20 06:10:40 chain = 0 set freq to 193.75 2023-11-20 06:10:40 chain = 1 set freq to 193.75 2023-11-20 06:10:41 chain = 0 set freq to 200.00 2023-11-20 06:10:41 chain = 1 set freq to 200.00 2023-11-20 06:10:41 chain = 0 set freq to 206.25 2023-11-20 06:10:41 chain = 1 set freq to 206.25 2023-11-20 06:10:41 chain = 0 set freq to 212.50 2023-11-20 06:10:41 chain = 1 set freq to 212.50 2023-11-20 06:10:42 chain = 0 set freq to 218.75 2023-11-20 06:10:42 chain = 1 set freq to 218.75 2023-11-20 06:10:42 chain = 0 set freq to 225.00 2023-11-20 06:10:42 chain = 1 set freq to 225.00 2023-11-20 06:10:42 chain = 0 set freq to 231.25 2023-11-20 06:10:42 chain = 1 set freq to 231.25 2023-11-20 06:10:42 chain = 0 set freq to 237.50 2023-11-20 06:10:42 chain = 1 set freq to 237.50 2023-11-20 06:10:43 chain = 0 set freq to 243.75 2023-11-20 06:10:43 chain = 1 set freq to 243.75 2023-11-20 06:10:43 chain = 0 set freq to 250.00 2023-11-20 06:10:43 chain = 1 set freq to 250.00 2023-11-20 06:10:43 chain = 0 set freq to 256.25 2023-11-20 06:10:43 chain = 1 set freq to 256.25 2023-11-20 06:10:44 chain = 0 set freq to 262.50 2023-11-20 06:10:44 chain = 1 set freq to 262.50 2023-11-20 06:10:44 chain = 0 set freq to 268.75 2023-11-20 06:10:44 chain = 1 set freq to 268.75 2023-11-20 06:10:44 chain = 0 set freq to 275.00 2023-11-20 06:10:44 chain = 1 set freq to 275.00 2023-11-20 06:10:45 chain = 0 set freq to 281.25 2023-11-20 06:10:45 chain = 1 set freq to 281.25 2023-11-20 06:10:45 chain = 0 set freq to 287.50 2023-11-20 06:10:45 chain = 1 set freq to 287.50 2023-11-20 06:10:45 chain = 0 set freq to 293.75 2023-11-20 06:10:45 chain = 1 set freq to 293.75 2023-11-20 06:10:46 chain = 0 set freq to 300.00 2023-11-20 06:10:46 chain = 1 set freq to 300.00 2023-11-20 06:10:46 chain = 0 set freq to 306.25 2023-11-20 06:10:46 chain = 1 set freq to 306.25 2023-11-20 06:10:46 chain = 0 set freq to 312.50 2023-11-20 06:10:46 chain = 1 set freq to 312.50 2023-11-20 06:10:46 chain = 0 set freq to 318.75 2023-11-20 06:10:46 chain = 1 set freq to 318.75 2023-11-20 06:10:47 chain = 0 set freq to 325.00 2023-11-20 06:10:47 chain = 1 set freq to 325.00 2023-11-20 06:10:47 chain = 0 set freq to 331.25 2023-11-20 06:10:47 chain = 1 set freq to 331.25 2023-11-20 06:10:47 chain = 0 set freq to 337.50 2023-11-20 06:10:47 chain = 1 set freq to 337.50 2023-11-20 06:10:48 chain = 0 set freq to 343.75 2023-11-20 06:10:48 chain = 1 set freq to 343.75 2023-11-20 06:10:48 chain = 0 set freq to 350.00 2023-11-20 06:10:48 chain = 1 set freq to 350.00 2023-11-20 06:10:48 chain = 0 set freq to 356.25 2023-11-20 06:10:48 chain = 1 set freq to 356.25 2023-11-20 06:10:49 chain = 0 set freq to 362.50 2023-11-20 06:10:49 chain = 1 set freq to 362.50 2023-11-20 06:10:49 chain = 0 set freq to 368.75 2023-11-20 06:10:49 chain = 1 set freq to 368.75 2023-11-20 06:10:49 chain = 0 set freq to 375.00 2023-11-20 06:10:49 chain = 1 set freq to 375.00 2023-11-20 06:10:49 chain = 0 set freq to 381.25 2023-11-20 06:10:49 chain = 1 set freq to 381.25 2023-11-20 06:10:50 chain = 0 set freq to 387.50 2023-11-20 06:10:50 chain = 1 set freq to 387.50 2023-11-20 06:10:50 chain = 0 set freq to 393.75 2023-11-20 06:10:50 chain = 1 set freq to 393.75 2023-11-20 06:10:50 chain = 0 set freq to 400.00 2023-11-20 06:10:50 chain = 1 set freq to 400.00 2023-11-20 06:10:51 chain = 0 set freq to 406.25 2023-11-20 06:10:51 chain = 1 set freq to 406.25 2023-11-20 06:10:51 chain = 0 set freq to 412.50 2023-11-20 06:10:51 chain = 1 set freq to 412.50 2023-11-20 06:10:51 chain = 0 set freq to 418.75 2023-11-20 06:10:51 chain = 1 set freq to 418.75 2023-11-20 06:10:52 chain = 0 set freq to 425.00 2023-11-20 06:10:52 chain = 1 set freq to 425.00 2023-11-20 06:10:52 chain = 0 set freq to 431.25 2023-11-20 06:10:52 chain = 1 set freq to 431.25 2023-11-20 06:10:52 chain = 0 set freq to 437.50 2023-11-20 06:10:52 chain = 1 set freq to 437.50 2023-11-20 06:10:52 chain = 0 set freq to 443.75 2023-11-20 06:10:52 chain = 1 set freq to 443.75 2023-11-20 06:10:53 chain = 0 set freq to 450.00 2023-11-20 06:10:53 chain = 1 set freq to 450.00 2023-11-20 06:10:53 chain = 0 set freq to 456.25 2023-11-20 06:10:53 chain = 1 set freq to 456.25 2023-11-20 06:10:53 chain = 0 set freq to 462.50 2023-11-20 06:10:53 chain = 1 set freq to 462.50 2023-11-20 06:10:54 chain = 0 set freq to 468.75 2023-11-20 06:10:54 chain = 1 set freq to 468.75 2023-11-20 06:10:54 chain = 0 set freq to 475.00 2023-11-20 06:10:54 chain = 1 set freq to 475.00 2023-11-20 06:10:54 chain = 0 set freq to 481.25 2023-11-20 06:10:54 chain = 1 set freq to 481.25 2023-11-20 06:10:55 chain = 0 set freq to 487.50 2023-11-20 06:10:55 chain = 1 set freq to 487.50 2023-11-20 06:10:55 chain = 0 set freq to 493.75 2023-11-20 06:10:55 chain = 1 set freq to 493.75 2023-11-20 06:10:55 chain = 0 set freq to 500.00 2023-11-20 06:10:55 chain = 1 set freq to 500.00 2023-11-20 06:10:55 chain = 0 set freq to 506.25 2023-11-20 06:10:55 chain = 1 set freq to 506.25 2023-11-20 06:10:56 chain = 0 set freq to 512.50 2023-11-20 06:10:56 chain = 1 set freq to 512.50 2023-11-20 06:10:56 chain = 0 set freq to 518.75 2023-11-20 06:10:56 chain = 1 set freq to 518.75 2023-11-20 06:10:56 chain = 0 set freq to 525.00 2023-11-20 06:10:56 chain = 1 set freq to 525.00 2023-11-20 06:10:57 chain = 0 set freq to 531.25 2023-11-20 06:10:57 chain = 1 set freq to 531.25 2023-11-20 06:10:57 chain = 0 set freq to 537.50 2023-11-20 06:10:57 chain = 1 set freq to 537.50 2023-11-20 06:10:57 chain = 0 set freq to 543.75 2023-11-20 06:10:57 chain = 1 set freq to 543.75 2023-11-20 06:10:58 chain = 0 set freq to 550.00 2023-11-20 06:10:58 chain = 1 set freq to 550.00 2023-11-20 06:10:58 chain = 0 set freq to 556.25 2023-11-20 06:10:58 chain = 1 set freq to 556.25 2023-11-20 06:10:58 chain = 0 set freq to 562.50 2023-11-20 06:10:58 chain = 1 set freq to 562.50 2023-11-20 06:10:58 chain = 0 set freq to 568.75 2023-11-20 06:10:58 chain = 1 set freq to 568.75 2023-11-20 06:10:59 chain = 0 set freq to 575.00 2023-11-20 06:10:59 chain = 1 set freq to 575.00 2023-11-20 06:10:59 chain = 0 set freq to 581.25 2023-11-20 06:10:59 chain = 1 set freq to 581.25 2023-11-20 06:10:59 chain = 0 set freq to 587.50 2023-11-20 06:10:59 chain = 1 set freq to 587.50 2023-11-20 06:11:00 chain = 0 set freq to 593.75 2023-11-20 06:11:00 chain = 1 set freq to 593.75 2023-11-20 06:11:00 chain = 0 set freq to 600.00 2023-11-20 06:11:00 chain = 1 set freq to 600.00 2023-11-20 06:11:00 chain = 0 set freq to 606.25 2023-11-20 06:11:00 chain = 1 set freq to 606.25 2023-11-20 06:11:01 chain = 0 set freq to 612.50 2023-11-20 06:11:01 chain = 1 set freq to 612.50 2023-11-20 06:11:01 chain = 0 set freq to 618.75 2023-11-20 06:11:01 chain = 1 set freq to 618.75 2023-11-20 06:11:01 chain = 0 set freq to 625.00 2023-11-20 06:11:01 chain = 1 set freq to 625.00 2023-11-20 06:11:01 chain = 0 set freq to 631.25 2023-11-20 06:11:01 chain = 1 set freq to 631.25 2023-11-20 06:11:02 chain = 0 set freq to 637.50 2023-11-20 06:11:02 chain = 1 set freq to 637.50 2023-11-20 06:11:02 chain = 0 set freq to 643.75 2023-11-20 06:11:02 chain = 1 set freq to 643.75 2023-11-20 06:11:02 chain = 0 set freq to 650.00 2023-11-20 06:11:02 chain = 1 set freq to 650.00 2023-11-20 06:11:03 chain = 0 set freq to 656.25 2023-11-20 06:11:03 chain = 1 set freq to 656.25 2023-11-20 06:11:03 chain = 0 set freq to 662.50 2023-11-20 06:11:03 chain = 1 set freq to 662.50 2023-11-20 06:11:03 chain = 0 set freq to 668.75 2023-11-20 06:11:03 chain = 1 set freq to 668.75 2023-11-20 06:11:04 chain = 0 set freq to 675.00 2023-11-20 06:11:04 chain = 1 set freq to 675.00 2023-11-20 06:11:04 enter mixed freq cfg 2023-11-20 06:11:04 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1 2023-11-20 06:11:04 start do_core_reset 2023-11-20 06:11:13 end do_core_reset 2023-11-20 06:11:23 set_voltage_by_steps to 1580. 2023-11-20 06:11:25 Init done! 2023-11-20 06:11:25 STATUS_OKAY 2023-11-20 06:11:25 start the cached job 2023-11-20 06:11:25 Version num 65536 2023-11-20 06:11:25 Mask num 0x1fffe000 2023-11-20 06:11:25 opt_multi_version = 65536, interval timeout = 2290648 2023-11-20 06:11:25 freq = 675, percent = 90, hcn = 3883, timeout = 2290648 2023-11-20 06:11:25 set_start_time_point total_tv_start_sys=353 total_tv_end_sys=354
-
Dear customer.
From the kernel log, it can't detect the hashboard. please kindly exclude the issue by following steps:
1.Check the wires for the hashboard--pull them and re-plug them again, and also you can try to change the new wires.
2.Please clean up the dust.
How To Clean and Dust The Antminers
https://support.bitmain.com/hc/en-us/articles/115004520173-How-To-Clean-and-Dust-The-Antminers
If there are still the same problems after the above steps, please send it to repair.
Best regards
BITMAIN
-
Dear Customer,
If you have any questions please feel free to contact us.
Please send email to customersupport@bitmain.com
We will reply to your question as soon as possible.
请先登录再写评论。
评论
2 条评论