S19 Pro 100th : notice kernel space clean work failed

s19 pro 100th stopped working.  Error notice kernel space clean work failed

[    0.000000@0] Booting Linux on physical CPU 0x0
[    0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Mon Dec 26 17:29:52 CST 2022
[    0.000000@0] Boot CPU: AArch64 Processor [410fd034]
[    0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '')
[    0.000000@0] bootconsole [aml_uart0] enabled
[    0.000000@0] efi: Getting EFI parameters from FDT:
[    0.000000@0] efi: UEFI not found.
[    0.000000@0] 	07400000 - 07500000,     1024 KB, ramoops@0x07400000
[    0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB
[    0.000000@0] 	05000000 - 05400000,     4096 KB, linux,secmon
[    0.000000@0] cma: Reserved 16 MiB at 0x000000000f000000
[    0.000000@0] On node 0 totalpages: 65536
[    0.000000@0]   DMA zone: 1024 pages used for memmap
[    0.000000@0]   DMA zone: 0 pages reserved
[    0.000000@0]   DMA zone: 65536 pages, LIFO batch:15
[    0.000000@0] psci: probing for conduit method from DT.
[    0.000000@0] psci: PSCIv1.0 detected in firmware.
[    0.000000@0] psci: Using standard PSCI v0.2 function IDs
[    0.000000@0] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000@0] psci: SMC Calling Convention v1.1
[    0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00ef53000 s64536 r8192 d29672 u102400
[    0.000000@0] pcpu-alloc: s64536 r8192 d29672 u102400 alloc=25*4096
[    0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000@0] Detected VIPT I-cache on CPU0
[    0.000000@0] CPU features: enabling workaround for ARM erratum 845719
[    0.000000@0] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64512
[    0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 rootfstype=ramfs init=/sbin/init
[    0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes)
[    0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.000000@0] Memory: 211688K/262144K available (8764K kernel code, 1194K rwdata, 2424K rodata, 3648K init, 1017K bss, 29976K reserved, 20480K cma-reserved)
[    0.000000@0] Virtual kernel memory layout:
[    0.000000@0]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000@0]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)
[    0.000000@0]       .text : 0xffffff8009080000 - 0xffffff8009910000   (  8768 KB)
[    0.000000@0]     .rodata : 0xffffff8009910000 - 0xffffff8009b80000   (  2496 KB)
[    0.000000@0]       .init : 0xffffff8009b80000 - 0xffffff8009f10000   (  3648 KB)
[    0.000000@0]       .data : 0xffffff8009f10000 - 0xffffff800a03aa00   (  1195 KB)
[    0.000000@0]        .bss : 0xffffff800a03aa00 - 0xffffff800a139034   (  1018 KB)
[    0.000000@0]     fixed   : 0xffffffbefe7fb000 - 0xffffffbefec00000   (  4116 KB)
[    0.000000@0]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)
[    0.000000@0]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)
[    0.000000@0]               0xffffffbf00000000 - 0xffffffbf00400000   (     4 MB actual)
[    0.000000@0]     memory  : 0xffffffc000000000 - 0xffffffc010000000   (   256 MB)
[    0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000@0] Preemptible hierarchical RCU implementation.
[    0.000000@0] 	Build-time adjustment of leaf fanout to 64.
[    0.000000@0] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000@0] NR_IRQS:64 nr_irqs:64 0
[    0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[    0.000000@0] axg_aoclkc_init: register ao clk ok!
[    0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[    0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[    0.000000@0] axg_amlogic_init_media: register meson media clk
[    0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks
[    0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk
[    0.000000@0] axg_clkc_init initialization complete
[    0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000003@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.008254@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194
[    0.016903@0] Console: colour dummy device 80x25
[    0.021106@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.031586@0] pid_max: default: 32768 minimum: 301
[    0.036434@0] thread_stack_cache_init, vmap:ffffffc00e5af600, bitmap:ffffffc00e5a3000, cache page:e5e0
[    0.045772@0] thread_stack_cache_init, allocation vm area:ffffffc00e5d94c0, addr:ffffff8020000000, size:20001000
[    0.056006@0] cpu 0, vmap_stack:[ffffffc00ef5c960-ffffffc00ef60950]
[    0.062304@0] cpu 0, irq_stack: [ffffffc00ef53060-ffffffc00ef57050]
[    0.068604@0] cpu 1, vmap_stack:[ffffffc00ef75960-ffffffc00ef79950]
[    0.074904@0] cpu 1, irq_stack: [ffffffc00ef6c060-ffffffc00ef70050]
[    0.081204@0] cpu 2, vmap_stack:[ffffffc00ef8e960-ffffffc00ef92950]
[    0.087504@0] cpu 2, irq_stack: [ffffffc00ef85060-ffffffc00ef89050]
[    0.093804@0] cpu 3, vmap_stack:[ffffffc00efa7960-ffffffc00efab950]
[    0.100104@0] cpu 3, irq_stack: [ffffffc00ef9e060-ffffffc00efa2050]
[    0.106463@0] Security Framework initialized
[    0.110696@0] SELinux:  Initializing.
[    0.114389@0] SELinux:  Starting in permissive mode
[    0.114426@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
[    0.121107@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
[    0.128838@0] ftrace: allocating 30061 entries in 118 pages
[    0.186260@0] sched-energy: CPU device node has no sched-energy-costs
[    0.187068@0] CPU0: update cpu_capacity 1024
[    0.191395@0] ASID allocator initialised with 32768 entries
[    0.229532@0] secmon: can't fine clear_range
[    0.229737@0] EFI services will not be available.
[    0.232998@0] Meson chip version = RevC (25:C - 23:0)
[    0.266668@1] Detected VIPT I-cache on CPU1
[    0.266727@1] CPU1: update cpu_capacity 1024
[    0.266730@1] CPU1: Booted secondary processor [410fd034]
[    0.294736@2] Detected VIPT I-cache on CPU2
[    0.294789@2] CPU2: update cpu_capacity 1024
[    0.294791@2] CPU2: Booted secondary processor [410fd034]
[    0.322792@3] Detected VIPT I-cache on CPU3
[    0.322841@3] CPU3: update cpu_capacity 1024
[    0.322844@3] CPU3: Booted secondary processor [410fd034]
[    0.322932@0] Brought up 4 CPUs
[    0.362154@0] SMP: Total of 4 processors activated.
[    0.367062@0] CPU features: detected feature: 32-bit EL0 Support
[    0.373098@0] CPU features: detected feature: Kernel page table isolation (KPTI)
[    0.383653@0] CPU: All CPU(s) started at EL2
[    0.384838@0] alternatives: patching kernel code
[    0.390139@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755
[    0.397368@0] devtmpfs: initialized
[    0.412391@0] DMI not present or invalid.
[    0.412777@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.420755@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.427329@0] pinctrl core: initialized pinctrl subsystem
[    0.433725@0] NET: Registered protocol family 16
[    0.457284@0] cpuidle: using governor menu
[    0.457773@0] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000)
[    0.463397@0] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers.
[    0.470797@0] DMA: preallocated 256 KiB pool for atomic allocations
[    0.476991@0] clkmsr: clkmsr: driver init
[    0.481004@0] aml_watch_point_probe, in, wp:2
[    0.485565@0] pstore: using zlib compression
[    0.489833@0] console [pstore-1] enabled
[    0.493273@0] pstore: Registered ramoops as persistent store backend
[    0.499686@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0
[    0.514020@0] aml_iomap: amlogic iomap probe done
[    0.520866@0] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c
[    0.522807@0] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0
[    0.623048@0] usbcore: registered new interface driver usbfs
[    0.623219@0] usbcore: registered new interface driver hub
[    0.628829@0] usbcore: registered new device driver usb
[    0.634143@0] pps_core: LinuxPPS API ver. 1 registered
[    0.639067@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.648452@0] PTP clock support registered
[    0.652778@0] dmi: Firmware registration failed.
[    0.657780@0] secmon: reserve_mem_size:0x300000
[    0.661812@0] secmon secmon: assigned reserved memory node linux,secmon
[    0.668724@0] secmon: get page:ffffffbf00140000, 5000
[    0.673427@0] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000
[    0.681814@0] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
[    0.689679@0] NetLabel: Initializing
[    0.691865@0] NetLabel:  domain hash size = 128
[    0.696451@0] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.701681@0] NetLabel:  unlabeled traffic allowed by default
[    0.708288@0] clocksource: Switched to clocksource arch_sys_counter
[    0.835110@0] VFS: Disk quotas dquot_6.6.0
[    0.835257@0] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.861269@1] NET: Registered protocol family 2
[    0.862309@1] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.867562@1] TCP bind hash table entries: 2048 (order: 3, 32768 bytes)
[    0.874174@1] TCP: Hash tables configured (established 2048 bind 2048)
[    0.880751@1] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.886732@1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.893471@1] NET: Registered protocol family 1
[    0.898428@1] RPC: Registered named UNIX socket transport module.
[    0.903857@1] RPC: Registered udp transport module.
[    0.908751@1] RPC: Registered tcp transport module.
[    0.913642@1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.922794@1] Unpacking initramfs...
[    1.422337@0] Initramfs unpacking failed: junk in compressed archive
[    1.429164@0] Freeing initrd memory: 6572K
[    1.430038@0] hw perfevents: clusterb_enabled = 0
[    1.432384@0] hw perfevents: cpumasks 0xf, 0x0
[    1.436902@0] hw perfevents: cluster A irq = 7
[    1.441458@0] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    1.451538@0] audit: initializing netlink subsys (disabled)
[    1.454974@0] audit: type=2000 audit(1.268:1): initialized
[    1.462180@0] workingset: timestamp_bits=62 max_order=16 bucket_order=0
[    1.486505@2] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.489476@2] NFS: Registering the id_resolver key type
[    1.492177@2] Key type id_resolver registered
[    1.496604@2] Key type id_legacy registered
[    1.501186@2] fuse init (API version 7.26)
[    1.506616@2] SELinux:  Registering netfilter hooks
[    1.512733@2] NET: Registered protocol family 38
[    1.512792@2] Key type asymmetric registered
[    1.516005@2] Asymmetric key parser 'x509' registered
[    1.521525@2] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    1.528737@2] io scheduler noop registered (default)
[    1.533698@2] io scheduler deadline registered
[    1.538536@2] io scheduler cfq registered
[    1.558759@1] random: fast init done
[    1.558856@1] random: crng init done
[    1.559314@2] Unable to detect cache hierarchy for CPU 0
[    1.595891@2] loop: module loaded
[    1.601432@2] zram: Added device: zram0
[    1.601835@2] mtdoops: mtd device (mtddev=name/number) must be supplied
[    1.606982@2] libphy: Fixed MDIO Bus: probed
[    1.611500@2] tun: Universal TUN/TAP device driver, 1.6
[    1.615854@2] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.624050@2]  ee eth reset:Addr = ffffff80081fd008
[    1.631556@2] meson6-dwmac ff3f0000.ethernet: no reset control found
[    1.633530@2] stmmac - user ID: 0x11, Synopsys ID: 0x37
[    1.638769@2]  Ring mode enabled
[    1.641995@2]  DMA HW capability register supported
[    1.646727@2]  Normal descriptors
[    1.650042@2]  RX Checksum Offload Engine supported
[    1.654943@2] 	COE Type 2
[    1.657571@2]  TX Checksum insertion supported
[    1.662029@2]  Wake-Up On Lan supported
[    1.665973@2]  Enable RX Mitigation via HW Watchdog Timer
[    1.684838@2] libphy: stmmac: probed
[    1.684892@2] eth%d: PHY ID 00000128 at 0 IRQ POLL (stmmac-0:00) active
[    1.689474@2] eth%d: PHY ID 00000128 at 3 IRQ POLL (stmmac-0:03)
[    1.697405@2] PPP generic driver version 2.4.2
[    1.700424@2] PPP BSD Compression module registered
[    1.704867@2] PPP Deflate Compression module registered
[    1.710129@2] PPP MPPE Compression module registered
[    1.715084@2] NET: Registered protocol family 24
[    1.720616@2] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.726472@2] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.733520@2] usbcore: registered new interface driver cdc_acm
[    1.738736@2] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.747136@2] usbcore: registered new interface driver usbserial
[    1.753853@1] mousedev: PS/2 mouse device common for all mice
[    1.759272@1] usbcore: registered new interface driver xpad
[    1.764676@2] i2c /dev entries driver
[    1.769461@2] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
[    1.773703@2] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
[    1.784702@2] ff803000.serial: clock gate not found
[    1.786185@2] meson_uart ff803000.serial: ==uart0 reg addr = ffffff800830d000
[    1.793409@2] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 13, base_baud = 1500000) is a meson_uart
[    1.808336@2] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200
[    1.811023@2] console [ttyS0] enabled
[    1.818257@2] bootconsole [aml_uart0] disabled
[    1.827931@3] ff804000.serial: clock gate not found
[    1.832065@3] meson_uart ff804000.serial: ==uart3 reg addr = ffffff8008321000
[    1.839170@3] ff804000.serial: ttyS3 at MMIO 0xff804000 (irq = 14, base_baud = 1500000) is a meson_uart
[    1.849516@0] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff8008323000
[    1.855665@0] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 25, base_baud = 1500000) is a meson_uart
[    1.865893@2] meson_uart ffd23000.serial: ==uart2 reg addr = ffffff8008325000
[    1.872135@2] ffd23000.serial: ttyS2 at MMIO 0xffd23000 (irq = 26, base_baud = 1500000) is a meson_uart
[    1.883036@3] amlogic-new-usb2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff8008348000
[    1.892419@3] amlogic-new-usb3 ffe09080.usb3phy: This phy has no usb port
[    1.898859@3] amlogic-new-usb3 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff800834c080
[    1.913869@3] i2c i2c-1: of_i2c: modalias failure on /soc/aobus@ff800000/i2c@5000/mcu6350@40
[    1.917699@3] i2c i2c-1: Failed to create I2C device for /soc/aobus@ff800000/i2c@5000/mcu6350@40
[    1.930022@3] aml_dma ff63e000.aml_dma: Aml dma
[    1.933155@3] aml_aes_dma ff63e000.aml_dma:aml_aes: Aml AES_dma
[    1.938197@3] aml_sha_dma ff63e000.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma
[    1.944590@3] efusekeynum: 4
[    1.946885@3] efusekeyname:             mac	offset:     0	size:     6
[    1.953331@3] efusekeyname:          mac_bt	offset:     6	size:     6
[    1.959727@3] efusekeyname:        mac_wifi	offset:    12	size:     6
[    1.966142@3] efusekeyname:            usid	offset:    18	size:    16
[    1.972949@2] efuse efuse: probe OK!
[    1.978403@2] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller
[    1.985664@2] meson-mmc: >>>>>>>>hostbase ffffff8008358000, dmode 
[    1.990733@2] meson-mmc: actual_clock :400000, HHI_nand: 0x80
[    1.995947@2] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c
[    2.040427@2] meson-mmc: meson_mmc_probe() : success!
[    2.040681@2] amlogic mtd driver init
[    2.044758@2] prase_get_dtb_nand_parameter:128,parse dts start
[    2.049496@2] bl mode descrete
[    2.052374@2] fip_copies 4
[    2.055038@2] fip_size 0x200000
[    2.058178@2] nand_clk_ctrl 0xffe07000
[    2.061902@2] prase_get_dtb_nand_parameter:234,parse dts end
[    2.067569@2] nand_clk_ctrl 0xffe07000
[    2.071298@2] nand register base ffffff80083df800, nand clock register ffffff80083e1000
[    2.080033@2] plat->aml_nand_device ffffff800a005c10
[    2.084184@2] m3_nand_probe() aml_nand_device ffffff800a005c10
[    2.090256@2] NAND device id: 98 da 90 15 76 16
[    2.094515@2] NAND device: Manufacturer ID: 
[    2.098565@2]  0x98, Chip ID: 0x98 (Toshiba A revision NAND 2Gib TC58NVG1S3HBAI4 )
[    2.106129@2] oob_fill_cnt =32 oob_size =64, bch_bytes =14
[    2.111561@2] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
[    2.117110@2] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
[    2.123355@2] mtd->oobavail: 0x8
[    2.126776@2] aml_nand_init 2119: plat-name:bootloader
[    2.131678@2] Creating 1 MTD partitions on "bootloader":
[    2.136963@2] 0x000000000000-0x000000200000 : "bootloader"
[    2.146327@3] bootloader initialized ok
[    2.146382@3] plat->aml_nand_device ffffff800a005c10
[    2.151218@3] m3_nand_probe() aml_nand_device ffffff800a005c10
[    2.157336@3] NAND device id: 98 da 90 15 76 16
[    2.161492@3] NAND device: Manufacturer ID: 
[    2.165568@3]  0x98, Chip ID: 0x98 (Toshiba A revision NAND 2Gib TC58NVG1S3HBAI4 )
[    2.173140@3] oob_fill_cnt =32 oob_size =64, bch_bytes =14
[    2.178564@3] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
[    2.184104@3] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
[    2.190354@3] mtd->oobavail: 0x8
[    2.193770@3] aml_nand_init 2119: plat-name:nandnormal
[    2.198710@3] bbt_start=20
[    2.201350@3] env_start=24
[    2.204015@3] key_start=32
[    2.206721@3] dtb_start=40
[    2.209405@3] ddr_start=44
[    2.212079@3] nbbt: info size=0x800 max_scan_blk=24, start_blk=20
[    2.218610@3] get_free_node 43: bitmap=0
[    2.222063@3] get_free_node 55: bitmap=1
[    2.226167@3] get_free_node 43: bitmap=1
[    2.229861@3] get_free_node 55: bitmap=3
[    2.233967@3] get_free_node 43: bitmap=3
[    2.237661@3] get_free_node 55: bitmap=7
[    2.241562@3] nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1
[    2.248232@3] nbbt free list:
[    2.251180@3] blockN=21, ec=-1, dirty_flag=0
[    2.255426@3] blockN=22, ec=-1, dirty_flag=0
[    2.259671@3] blockN=23, ec=-1, dirty_flag=0
[    2.263921@3] aml_nand_scan_rsv_info 1141: page_num=1
[    2.269356@3] nbbt valid addr: 280000
[    2.272589@3] aml_nand_bbt_check 1306 bbt is valid, reading.
[    2.278222@3] aml_nand_read_rsv_info:423,read nbbt info at 280000
[    2.284495@3] nenv: info size=0x10000 max_scan_blk=32, start_blk=24
[    2.290936@3] get_free_node 43: bitmap=7
[    2.294428@3] get_free_node 55: bitmap=f
[    2.298532@3] get_free_node 43: bitmap=f
[    2.302228@3] get_free_node 55: bitmap=1f
[    2.306419@3] get_free_node 43: bitmap=1f
[    2.310201@3] get_free_node 55: bitmap=3f
[    2.314392@3] get_free_node 43: bitmap=3f
[    2.318175@3] get_free_node 55: bitmap=7f
[    2.322366@3] get_free_node 43: bitmap=7f
[    2.326146@3] get_free_node 55: bitmap=ff
[    2.330339@3] get_free_node 43: bitmap=ff
[    2.334122@3] get_free_node 55: bitmap=1ff
[    2.338399@3] get_free_node 43: bitmap=1ff
[    2.342268@3] get_free_node 55: bitmap=3ff
[    2.346341@3] nenv : phy_blk_addr=24, ec=0, phy_page_addr=0, timestamp=1
[    2.353012@3] nenv free list:
[    2.355943@3] blockN=25, ec=-1, dirty_flag=0
[    2.360206@3] blockN=26, ec=-1, dirty_flag=0
[    2.364453@3] blockN=27, ec=-1, dirty_flag=0
[    2.368700@3] blockN=28, ec=-1, dirty_flag=0
[    2.372946@3] blockN=29, ec=-1, dirty_flag=0
[    2.377193@3] blockN=30, ec=-1, dirty_flag=0
[    2.381439@3] blockN=31, ec=-1, dirty_flag=0
[    2.385686@3] aml_nand_scan_rsv_info 1141: page_num=32
[    2.403759@3] nenv valid addr: 310000
[    2.403793@3] nkey: info size=0x8000 max_scan_blk=40, start_blk=32
[    2.408177@3] get_free_node 43: bitmap=3ff
[    2.412035@3] get_free_node 55: bitmap=7ff
[    2.416327@3] get_free_node 43: bitmap=7ff
[    2.420163@3] get_free_node 55: bitmap=fff
[    2.424476@3] get_free_node 43: bitmap=fff
[    2.428328@3] get_free_node 55: bitmap=1fff
[    2.432693@3] get_free_node 43: bitmap=1fff
[    2.436648@3] get_free_node 55: bitmap=3fff
[    2.441012@3] get_free_node 43: bitmap=3fff
[    2.444968@3] get_free_node 55: bitmap=7fff
[    2.449333@3] get_free_node 43: bitmap=7fff
[    2.453288@3] get_free_node 55: bitmap=ffff
[    2.457653@3] get_free_node 43: bitmap=ffff
[    2.461608@3] get_free_node 55: bitmap=1ffff
[    2.466059@3] get_free_node 43: bitmap=1ffff
[    2.470102@3] get_free_node 55: bitmap=3ffff
[    2.474348@3] nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
[    2.481019@3] nkey free list:
[    2.483949@3] blockN=32, ec=-1, dirty_flag=0
[    2.488213@3] blockN=33, ec=-1, dirty_flag=0
[    2.492460@3] blockN=34, ec=-1, dirty_flag=0
[    2.496706@3] blockN=35, ec=-1, dirty_flag=0
[    2.500952@3] blockN=36, ec=-1, dirty_flag=0
[    2.505199@3] blockN=37, ec=-1, dirty_flag=0
[    2.509446@3] blockN=38, ec=-1, dirty_flag=0
[    2.513692@3] blockN=39, ec=-1, dirty_flag=0
[    2.517939@3] aml_nand_scan_rsv_info 1141: page_num=16
[    2.523051@3] nkey valid addr: fffffffffffe0000
[    2.527560@3] aml_nand_key_check 1251 NO key exist
[    2.532328@3] ndtb: info size=0x20000 max_scan_blk=44, start_blk=40
[    2.538975@3] get_free_node 43: bitmap=3ffff
[    2.542814@3] get_free_node 55: bitmap=7ffff
[    2.547266@3] get_free_node 43: bitmap=7ffff
[    2.551308@3] get_free_node 55: bitmap=fffff
[    2.555759@3] get_free_node 43: bitmap=fffff
[    2.559801@3] get_free_node 55: bitmap=1fffff
[    2.564135@3] ndtb : phy_blk_addr=40, ec=0, phy_page_addr=0, timestamp=1
[    2.570806@3] ndtb free list:
[    2.573753@3] blockN=41, ec=-1, dirty_flag=0
[    2.577999@3] blockN=42, ec=-1, dirty_flag=0
[    2.582246@3] blockN=43, ec=-1, dirty_flag=0
[    2.586492@3] aml_nand_scan_rsv_info 1141: page_num=64
[    2.604574@3] ndtb valid addr: 500000
[    2.604608@3] nddr: info size=0x20000 max_scan_blk=46, start_blk=44
[    2.609068@3] get_free_node 43: bitmap=1fffff
[    2.613197@3] get_free_node 55: bitmap=3fffff
[    2.617734@3] get_free_node 43: bitmap=3fffff
[    2.621863@3] get_free_node 55: bitmap=7fffff
[    2.626197@3] nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
[    2.632867@3] nddr free list:
[    2.635798@3] blockN=44, ec=-1, dirty_flag=0
[    2.640061@3] blockN=45, ec=-1, dirty_flag=0
[    2.644309@3] aml_nand_scan_rsv_info 1141: page_num=64
[    2.649421@3] nddr valid addr: fffffffffffe0000
[    2.653928@3] aml_nand_ddr_check 1281 NO ddr exist
[    2.658698@3] tpl: off 8388608, size 8388608
[    2.756581@3]  NAND bbt detect factory Bad block at c000000
[    2.756632@3] aml_nand_add_partition:394 factory bad addr=600
[    2.762311@3]  NAND bbt detect factory Bad block at c020000
[    2.767813@3] aml_nand_add_partition:394 factory bad addr=601
[    2.807506@3] Creating 6 MTD partitions on "nandnormal":
[    2.807553@3] 0x000000800000-0x000001000000 : "tpl"
[    2.819107@3] 0x000001000000-0x000001200000 : "misc"
[    2.822233@0] 0x000001200000-0x000002200000 : "recovery"
[    2.834248@1] 0x000002200000-0x000004200000 : "boot"
[    2.853541@0] 0x000004200000-0x000004700000 : "config"
[    2.858317@0] 0x000004700000-0x000010000000 : "nvdata"
[    2.923041@0]  NAND bbt detect factory Bad block at c000000
[    2.923155@0]  NAND bbt detect factory Bad block at c020000
[    2.965190@3] nandnormal initialized ok
[    2.965299@3] aml_ubootenv_init: register env chardev
[    2.968940@3] aml_ubootenv_init: register env chardev OK
[    2.973882@3] amlnf_dtb_init: register dtb cdev
[    2.978649@1] amlnf_dtb_init: register dtd cdev OK
[    2.983070@1] mtd_nand_probe 267 , err = 0
[    2.988169@2] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc0
[    2.993632@2] input: aml_vkeypad as /devices/platform/rtc/input/input0
[    3.000637@1] unifykey: storage in base: 0xffffffc005000000
[    3.005233@1] unifykey: storage out base: 0xffffffc005040000
[    3.010853@1] unifykey: storage block base: 0xffffffc005080000
[    3.016645@1] unifykey: probe done!
[    3.020839@1] unifykey: no efuse-version set, use default value: -1
[    3.026360@1] unifykey: key unify config unifykey-num is 6
[    3.031885@1] unifykey: key unify fact unifykey-num is 6
[    3.037108@1] unifykey: unifykey_devno: f200000
[    3.042125@3] unifykey: device unifykeys created ok
[    3.046639@3] unifykey: aml_unifykeys_init done!
[    3.051520@3] sysled: module init
[    3.054968@3] meson_wdt ffd0f0d0.watchdog: start watchdog
[    3.059743@3] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog
[    3.067122@0] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done
[    3.075911@3] dmc_monitor_probe
[    3.078378@3] defendkey defendkey: Reserved memory is not enough!
[    3.082494@3] defendkey: probe of defendkey failed with error -22
[    3.088830@3] GACT probability NOT on
[    3.092124@3] Mirror/redirect action on
[    3.095963@3] u32 classifier
[    3.098797@3]     Actions configured
[    3.102357@3] Netfilter messages via NETLINK v0.30.
[    3.107634@3] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[    3.113840@3] ctnetlink v0.93: registering with nfnetlink.
[    3.119657@3] xt_time: kernel timezone is -0000
[    3.123413@3] ipip: IPv4 and MPLS over IPv4 tunneling driver
[    3.130060@3] ip_tables: (C) 2000-2006 Netfilter Core Team
[    3.134755@3] arp_tables: arp_tables: (C) 2002 David S. Miller
[    3.140241@3] Initializing XFRM netlink socket
[    3.145767@3] NET: Registered protocol family 10
[    3.151410@3] mip6: Mobile IPv6
[    3.152359@3] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    3.158281@3] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    3.166261@3] NET: Registered protocol family 17
[    3.168561@3] NET: Registered protocol family 15
[    3.173154@3] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    3.186298@3] l2tp_core: L2TP core driver, V2.0
[    3.190690@3] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[    3.195606@3] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[    3.201364@3] l2tp_netlink: L2TP netlink interface
[    3.206153@3] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[    3.212233@3] l2tp_debugfs: L2TP debugfs support
[    3.216753@3] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[    3.223412@3] NET: Registered protocol family 35
[    3.228362@3] Key type dns_resolver registered
[    3.232894@3] Registered swp emulation handler
[    3.236793@3] Registered cp15_barrier emulation handler
[    3.241988@3] Registered setend emulation handler
[    3.246725@3] disable EAS feature
[    3.251537@1] registered taskstats version 1
[    3.267846@3] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host
[    3.774385@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.774473@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    3.782784@3] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f664 hci version 0x100 quirks 0x02010010
[    3.791203@3] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0xff500000
[    3.798646@2] hub 1-0:1.0: USB hub found
[    3.801148@2] hub 1-0:1.0: 1 port detected
[    3.805778@2] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.810775@2] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    3.818668@2] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.828139@3] hub 2-0:1.0: USB hub found
[    3.830775@3] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    3.838053@3] usb usb2: Unsupported the hub
[    3.842812@3] aml_vrtc rtc: setting system clock to 2015-01-01 00:00:09 UTC (1420070409)
[    3.850882@3] dwc_otg ff400000.dwc2_a: dwc_otg_driver_probe(ffffffc00d19f000)
[    3.850959@3] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0
[    3.858850@3] dwc_otg ff400000.dwc2_a: base=0xffffff8008580000
[    3.858863@3] dwc_otg ff400000.dwc2_a: dwc_otg_device=0xffffffc00bbcfa00
[    3.959432@3] dwc_otg: Core Release: 3.10a
[    3.959507@3] dwc_otg: Setting default values for core params
[    3.963678@3] dwc_otg: curmode: 0, host_only: 0
[    3.968184@3] dwc_otg ff400000.dwc2_a: DMA config: BURST_DEFAULT
[    3.980707@3] dwc_otg: Using Buffer DMA mode
[    3.980744@3] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[    3.984653@3] dwc_otg: Working on port type = SLAVE
[    3.989510@3] dwc_otg: Dedicated Tx FIFOs mode
[    3.996486@3] thermal thermal_zone0: binding zone soc_thermal with cdev thermal-cpufreq-0 failed:-22
[    4.003204@3] cpucore_cooling_register, max_cpu_core_num:4
[    4.015585@0] gxbb_pm: enter meson_pm_probe!
[    4.015644@0] no vddio3v3_en pin
[    4.017349@0] pm-meson aml_pm: Can't get switch_clk81
[    4.022381@0] gxbb_pm: meson_pm_probe done
[    4.027367@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
[    4.033687@0] Freeing unused kernel memory: 3648K
[    4.048106@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
[    4.304760@1] ubi0: attaching mtd5
[    4.324234@1] ubi0: scanning is finished
[    4.329448@2] ubi0: attached mtd5 (name "config", size 5 MiB)
[    4.329578@2] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    4.336649@2] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    4.343543@2] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    4.350657@2] ubi0: good PEBs: 40, bad PEBs: 0, corrupted PEBs: 0
[    4.356714@2] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[    4.364090@2] ubi0: max/mean erase counter: 8/4, WL threshold: 4096, image sequence number: 3372681672
[    4.373355@2] ubi0: available PEBs: 0, total reserved PEBs: 40, PEBs reserved for bad PEB handling: 4
[    4.382584@2] usb 1-1: new low-speed USB device number 2 using xhci-hcd
[    4.389211@1] ubi0: background thread "ubi_bgt0d" started, PID 1079
[    4.402124@0] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 1083
[    4.420298@2] UBIFS (ubi0:0): recovery needed
[    4.481068@2] UBIFS (ubi0:0): recovery completed
[    4.481344@2] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "config_data"
[    4.488075@2] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    4.498116@2] UBIFS (ubi0:0): FS size: 2793472 bytes (2 MiB, 22 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[    4.508339@2] UBIFS (ubi0:0): reserved for root: 131942 bytes (128 KiB)
[    4.514927@2] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID D261F7C3-96FA-45FC-9108-74470556AF3D, small LPT model
[    4.539367@1] ubi2: attaching mtd6
[    5.005869@1]  NAND bbt detect factory Bad block at c000000
[    5.005995@1]  NAND bbt detect factory Bad block at c020000
[    5.257579@1] ubi2: scanning is finished
[    5.265174@0] ubi2: attached mtd6 (name "nvdata", size 185 MiB)
[    5.265474@0] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    5.272538@0] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    5.279441@0] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096
[    5.286544@0] ubi2: good PEBs: 1478, bad PEBs: 2, corrupted PEBs: 0
[    5.292794@0] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128
[    5.300159@0] ubi2: max/mean erase counter: 273/120, WL threshold: 4096, image sequence number: 960084711
[    5.309693@0] ubi2: available PEBs: 0, total reserved PEBs: 1478, PEBs reserved for bad PEB handling: 2
[    5.319067@2] ubi2: background thread "ubi_bgt2d" started, PID 1091
[    5.332129@1] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 1095
[    5.350365@0] UBIFS (ubi2:0): recovery needed
[    5.500262@2] UBIFS (ubi2:0): recovery completed
[    5.500548@2] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "nvdata_data"
[    5.507286@2] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    5.517333@2] UBIFS (ubi2:0): FS size: 185384960 bytes (176 MiB, 1460 LEBs), journal size 9269248 bytes (8 MiB, 73 LEBs)
[    5.528162@2] UBIFS (ubi2:0): reserved for root: 4952683 bytes (4836 KiB)
[    5.534926@2] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID 29BE85B9-A3FC-4940-B9C8-39B4F8466403, small LPT model
[    5.758784@2] eth0: device MAC address 02:5c:dc:f9:7d:46
[    5.841992@0] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP.
[    5.843356@0] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    6.090812@3] uart_trans: loading out-of-tree module taints kernel.
[    6.093445@3] register uart_trans chrdev success.
[    6.096605@3] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 0 to 9600
[    6.104251@3] tty port open success [/dev/ttyS3]!
[    6.109070@3] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 9600 to 115200
[    6.117279@3] init sucess for tty struct (246:3)  [/dev/ttyS3]
[    6.123414@3] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 0 to 9600
[    6.131096@3] tty port open success [/dev/ttyS2]!
[    6.135743@3] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 9600 to 115200
[    6.144245@3] init sucess for tty struct (246:2)  [/dev/ttyS2]
[    6.150293@3] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 0 to 9600
[    6.157932@3] tty port open success [/dev/ttyS1]!
[    6.162590@3] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 115200
[    6.170968@3] init sucess for tty struct (246:1)  [/dev/ttyS1]
[    6.177268@0] create workqueue success!
[    7.896514@0] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
[    7.899624@0] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   14.744307@2] xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
[   14.746951@2] xhci-hcd xhci-hcd.0.auto: Assuming host is dying, halting host.
[   14.773944@2] xhci-hcd xhci-hcd.0.auto: Host not halted after 16000 microseconds.
[   14.775786@2] xhci-hcd xhci-hcd.0.auto: Non-responsive xHCI host is not halting.
[   14.783152@2] xhci-hcd xhci-hcd.0.auto: Completing active URBs anyway.
[   14.789708@2] xhci-hcd xhci-hcd.0.auto: HC died; cleaning up
[   14.795485@2] usb usb1-port1: couldn't allocate usb_device
[   35.865882@2] uart trans dev open.
[   35.865983@2] uart_buf virt addr = 0xffffffc00b180000
[   35.868793@2] uart_buf phys addr = 0x0b180000
[   35.873100@2] uart_buf pfn       = 0x0000b180
[   35.877908@2] uart trans stop send work timer.
[   35.882076@2] uart trans set chain exist bits:0x7.
[   35.886637@2] uart trans set work queue count 768.
[ 1408.445520@0] nf_conntrack: default automatic helper assignment has been turned off for security reasons and CT-based  firewall rule not found. Use the iptables CT target to attach helpers instead.


===========================================Miner log===========================================
2015-01-01 00:00:16 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX sn :YDFTEMUBBJFJA00X3
2015-01-01 00:00:17 This is fix-freq version
2015-01-01 00:00:17 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX
2015-01-01 00:00:17 Miner sn: YDFTEMUBBJFJA00X3
2015-01-01 00:00:17 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 17:22:17
2015-01-01 00:00:17 opt_multi_version     = 1
2015-01-01 00:00:17 opt_bitmain_ab        = 1
2015-01-01 00:00:17 mid_auto_gen          = 1
2015-01-01 00:00:17 opt_bitmain_work_mode = 3
2015-01-01 00:00:17 port 439 already exported
2015-01-01 00:00:17 port 454 already exported
2015-01-01 00:00:17 port 440 already exported
2015-01-01 00:00:17 port 455 already exported
2015-01-01 00:00:17 port 441 already exported
2015-01-01 00:00:17 port 456 already exported
2015-01-01 00:00:17 port 438 already exported
2015-01-01 00:00:17 port 453 already exported
2015-01-01 00:00:17 port 446 already exported
2015-01-01 00:00:17 port 445 already exported
2015-01-01 00:00:17 Note: front fan is power on!
2015-01-01 00:00:17 Note: rear fan is power on!
2015-01-01 00:00:17 start the http log.
2015-01-01 00:00:17 httpListenThread start ret=0
2015-01-01 00:00:17 start listen on 6060 ...
2015-01-01 00:00:17 bad chain id = 3
2015-01-01 00:00:20 bad chain id = 3
2015-01-01 00:00:22 ==========================capability start==========================
2015-01-01 00:00:22 board num = 3
2015-01-01 00:00:22 board id = 0, chain num = 1
2015-01-01 00:00:22 	chain id = 0
2015-01-01 00:00:22 board id = 1, chain num = 1
2015-01-01 00:00:22 	chain id = 1
2015-01-01 00:00:22 board id = 2, chain num = 1
2015-01-01 00:00:22 	chain id = 2
2015-01-01 00:00:22 ==========================capability end============================
2015-01-01 00:00:22 chain num = 3
2015-01-01 00:00:23 skip loading levels for now
2023-11-12 22:12:06 load chain 0 eeprom data
2023-11-12 22:12:10 load chain 1 eeprom data
2023-11-12 22:12:13 load chain 2 eeprom data
2023-11-12 22:12:13 i2c_sim_init start
2023-11-12 22:12:13 init gpio477
2023-11-12 22:12:13 init gpio476
2023-11-12 22:12:13 i2c_sim_init end
2023-11-12 22:12:17 get power version failed
2023-11-12 22:12:17 check power version failed, use v2 protocal to try it again
2023-11-12 22:12:22 get power version failed
2023-11-12 22:12:22 power open power_version < 0 will close power
2023-11-12 22:12:22 bitmain power close ===========
2023-11-12 22:12:22 bitmain_power_version: auto exec bitmain_power_open, but open power failed
2023-11-12 22:12:22 miner type: Antminer S19 Pro
2023-11-12 22:12:22 multi machine mode
2023-11-12 22:12:22 load machine BHB42651 conf
2023-11-12 22:12:22 machine : BHB42651 
2023-11-12 22:12:22 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-11-12 22:12:22 abandon mix board!
2023-11-12 22:12:22 abandon mix board!
2023-11-12 22:12:22 fan_eft : 0  fan_pwm : 100
2023-11-12 22:12:22 create thread get_nonce_and_register_thread
2023-11-12 22:12:22 fixed working voltage = 1360
2023-11-12 22:12:22 fixed frequency is 525
2023-11-12 22:12:22 Chain [0] PCB Version: 0x0120
2023-11-12 22:12:22 Chain [0] BOM Version: 0x0020
2023-11-12 22:12:22 Chain [1] PCB Version: 0x0120
2023-11-12 22:12:22 Chain [1] BOM Version: 0x0020
2023-11-12 22:12:22 Chain [2] PCB Version: 0x0120
2023-11-12 22:12:22 Chain [2] BOM Version: 0x0020
2023-11-12 22:12:22 bad chain id = 3
2023-11-12 22:12:22 Fan check passed.
2023-11-12 22:12:22 uart_trans addr:0xf6e68000.
2023-11-12 22:12:22 max sensor num = 4
2023-11-12 22:12:22 STATUS_INITED: soc init done!
2023-11-12 22:12:22 temperature_monitor_thread start...
2023-11-12 22:12:24 start to init...
2023-11-12 22:12:24 i2c_sim_init start
2023-11-12 22:12:24 i2c_sim_init end
2023-11-12 22:12:28 get power version failed
2023-11-12 22:12:28 check power version failed, use v2 protocal to try it again
2023-11-12 22:12:33 get power version failed
2023-11-12 22:12:33 power open power_version < 0 will close power
2023-11-12 22:12:33 bitmain power close ===========
2023-11-12 22:12:33 bitmain_power_is_calibrated: auto exec bitmain_power_open, but open power failed
2023-11-12 22:12:33 warning:power is not calibration.
2023-11-12 22:12:33 i2c_sim_init start
2023-11-12 22:12:33 i2c_sim_init end
2023-11-12 22:12:37 get power version failed
2023-11-12 22:12:37 check power version failed, use v2 protocal to try it again
2023-11-12 22:12:42 get power version failed
2023-11-12 22:12:42 power open power_version < 0 will close power
2023-11-12 22:12:42 bitmain power close ===========
2023-11-12 22:12:42 bitmain_power_version: auto exec bitmain_power_open, but open power failed
2023-11-12 22:12:42 power type version: 0x80000300
2023-11-12 22:12:42 power type version error
2023-11-12 22:12:42 Sweep error string = V:1.
2023-11-12 22:12:42 ERROR_POWER_LOST: get power type version failed!
2023-11-12 22:12:42 stop_mining: get power type version failed!
2023-11-12 22:12:42 uninit_temp_info
2023-11-12 22:12:42 do not read temp anymore...
2023-11-12 22:12:42 cancel thread
2023-11-12 22:12:42 ****power off hashboard****
2023-11-12 22:12:42 temp monitor thread exit
2023-11-12 22:12:45 ERROR_SOC_INIT: soc init failed!
2023-11-12 22:12:45 stop_mining: soc init failed!
2023-11-12 22:12:45 ****power off hashboard****
2023-11-12 22:13:07 Version num 65536
2023-11-12 22:13:07 Mask num 0x1fffe000
2023-11-12 22:13:07 opt_multi_version = 65536, interval timeout = 3817748
2023-11-12 22:13:07 freq = 405, percent = 90, hcn = 6472, timeout = 3817748
2023-11-12 22:13:07 notice kernel space clean work failed.
2023-11-12 22:13:37 notice kernel space clean work failed.
2023-11-12 22:13:59 notice kernel space clean work failed.
2023-11-12 22:14:30 notice kernel space clean work failed.
2023-11-12 22:15:00 notice kernel space clean work failed.
2023-11-12 22:15:15 notice kernel space clean work failed.
2023-11-12 22:15:37 notice kernel space clean work failed.
2023-11-12 22:16:11 notice kernel space clean work failed.
2023-11-12 22:16:31 notice kernel space clean work failed.
2023-11-12 22:17:01 notice kernel space clean work failed.
2023-11-12 22:17:22 notice kernel space clean work failed.
2023-11-12 22:17:22 notice kernel space clean work failed.
2023-11-12 22:17:23 notice kernel space clean work failed.
2023-11-12 22:17:23 notice kernel space clean work failed.
2023-11-12 22:17:46 notice kernel space clean work failed.
2023-11-12 22:17:46 notice kernel space clean work failed.
2023-11-12 22:18:16 notice kernel space clean work failed.
2023-11-12 22:18:35 notice kernel space clean work failed.
2023-11-12 22:19:02 notice kernel space clean work failed.
2023-11-12 22:19:23 notice kernel space clean work failed.
2023-11-12 22:19:47 notice kernel space clean work failed.
2023-11-12 22:20:11 notice kernel space clean work failed.
2023-11-12 22:20:23 notice kernel space clean work failed.
2023-11-12 22:20:33 notice kernel space clean work failed.
2023-11-12 22:21:03 notice kernel space clean work failed.
2023-11-12 22:21:21 notice kernel space clean work failed.
2023-11-12 22:21:49 notice kernel space clean work failed.
2023-11-12 22:22:19 notice kernel space clean work failed.
2023-11-12 22:22:51 notice kernel space clean work failed.
2023-11-12 22:23:19 notice kernel space clean work failed.
2023-11-12 22:23:49 notice kernel space clean work failed.
2023-11-12 22:24:23 notice kernel space clean work failed.
2023-11-12 22:24:50 notice kernel space clean work failed.
2023-11-12 22:25:20 notice kernel space clean work failed.
2023-11-12 22:25:50 notice kernel space clean work failed.
2023-11-12 22:25:50 notice kernel space clean work failed.
2023-11-12 22:25:50 notice kernel space clean work failed.
2023-11-12 22:25:50 notice kernel space clean work failed.
2023-11-12 22:26:20 notice kernel space clean work failed.
2023-11-12 22:26:36 notice kernel space clean work failed.
2023-11-12 22:27:06 notice kernel space clean work failed.
2023-11-12 22:27:36 notice kernel space clean work failed.
2023-11-12 22:28:06 notice kernel space clean work failed.
2023-11-12 22:28:24 notice kernel space clean work failed.
2023-11-12 22:28:52 notice kernel space clean work failed.
2023-11-12 22:29:22 notice kernel space clean work failed.
2023-11-12 22:29:52 notice kernel space clean work failed.
2023-11-12 22:30:22 notice kernel space clean work failed.
2023-11-12 22:30:51 notice kernel space clean work failed.
2023-11-12 22:31:07 notice kernel space clean work failed.
2023-11-12 22:31:38 notice kernel space clean work failed.
2023-11-12 22:32:02 notice kernel space clean work failed.
2023-11-12 22:32:23 notice kernel space clean work failed.
2023-11-12 22:32:53 notice kernel space clean work failed.
2023-11-12 22:33:23 notice kernel space clean work failed.
2023-11-12 22:33:53 notice kernel space clean work failed.
2023-11-12 22:34:34 notice kernel space clean work failed.
2023-11-12 22:35:07 notice kernel space clean work failed.
2023-11-12 22:35:23 notice kernel space clean work failed.
2023-11-12 22:35:39 notice kernel space clean work failed.
2023-11-12 22:36:09 notice kernel space clean work failed.
2023-11-12 22:36:39 notice kernel space clean work failed.
2023-11-12 22:37:09 notice kernel space clean work failed.
2023-11-12 22:37:44 notice kernel space clean work failed.
2023-11-12 22:38:10 notice kernel space clean work failed.
2023-11-12 22:38:25 notice kernel space clean work failed.
2023-11-12 22:39:10 notice kernel space clean work failed.
2023-11-12 22:39:20 notice kernel space clean work failed.
2023-11-12 22:39:20 notice kernel space clean work failed.
2023-11-12 22:39:20 notice kernel space clean work failed.
2023-11-12 22:39:46 notice kernel space clean work failed.
2023-11-12 22:40:10 notice kernel space clean work failed.
2023-11-12 22:40:25 notice kernel space clean work failed.
2023-11-12 22:40:56 notice kernel space clean work failed.