S19J Pros - get power version failed

• We have replaced the PSU with 2 brand new PSUs from Bitmain and even ensured to try the Version A and the correct Version E power supply
• We cleaned all the dust in the unit
• Reseated all the connections
• Used a different control board
• Changed the power cabled with a known working one and outlet
• The firmware keeps going back to a debug mode after the first fail
• Reflashed it with an SD card
• Factory reset and put the correct pools back in
• Updated the firmware to the latest firmware
• This is one example of many S19J pros we have with the same issue

[    0.000000@0] Booting Linux on physical CPU 0x0
[    0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Tue Mar 29 14:04:45 CST 2022
[    0.000000@0] Boot CPU: AArch64 Processor [410fd034]
[    0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '')
[    0.000000@0] bootconsole [aml_uart0] enabled
[    0.000000@0] efi: Getting EFI parameters from FDT:
[    0.000000@0] efi: UEFI not found.
[    0.000000@0] 	07400000 - 07500000,     1024 KB, ramoops@0x07400000
[    0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB
[    0.000000@0] 	05000000 - 05400000,     4096 KB, linux,secmon
[    0.000000@0] __reserved_mem_alloc_size, start:0x000000003e000000, end:0x0000000040000000, len:32 MiB
[    0.000000@0] failed to allocate memory for node linux,meson-fb, size:32 MB
[    0.000000@0] cma: Reserved 8 MiB at 0x000000000f800000
[    0.000000@0] On node 0 totalpages: 65536
[    0.000000@0]   DMA zone: 1024 pages used for memmap
[    0.000000@0]   DMA zone: 0 pages reserved
[    0.000000@0]   DMA zone: 65536 pages, LIFO batch:15
[    0.000000@0] psci: probing for conduit method from DT.
[    0.000000@0] psci: PSCIv1.0 detected in firmware.
[    0.000000@0] psci: Using standard PSCI v0.2 function IDs
[    0.000000@0] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000@0] psci: SMC Calling Convention v1.1
[    0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00f753000 s64536 r8192 d29672 u102400
[    0.000000@0] pcpu-alloc: s64536 r8192 d29672 u102400 alloc=25*4096
[    0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000@0] Detected VIPT I-cache on CPU0
[    0.000000@0] CPU features: enabling workaround for ARM erratum 845719
[    0.000000@0] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64512
[    0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 androidboot.rpmb_state=0 rootfstype=ramfs init=/sbin/init
[    0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes)
[    0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.000000@0] Memory: 219896K/262144K available (8764K kernel code, 1194K rwdata, 2428K rodata, 3648K init, 1018K bss, 29960K reserved, 12288K cma-reserved)
[    0.000000@0] Virtual kernel memory layout:
[    0.000000@0]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000@0]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)
[    0.000000@0]       .text : 0xffffff8009080000 - 0xffffff8009910000   (  8768 KB)
[    0.000000@0]     .rodata : 0xffffff8009910000 - 0xffffff8009b80000   (  2496 KB)
[    0.000000@0]       .init : 0xffffff8009b80000 - 0xffffff8009f10000   (  3648 KB)
[    0.000000@0]       .data : 0xffffff8009f10000 - 0xffffff800a03aa00   (  1195 KB)
[    0.000000@0]        .bss : 0xffffff800a03aa00 - 0xffffff800a139534   (  1019 KB)
[    0.000000@0]     fixed   : 0xffffffbefe7fb000 - 0xffffffbefec00000   (  4116 KB)
[    0.000000@0]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)
[    0.000000@0]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)
[    0.000000@0]               0xffffffbf00000000 - 0xffffffbf00400000   (     4 MB actual)
[    0.000000@0]     memory  : 0xffffffc000000000 - 0xffffffc010000000   (   256 MB)
[    0.000000@0] can't find symbol:arm_dma_alloc
[    0.000000@0] can't find symbol:__alloc_from_contiguous
[    0.000000@0] can't find symbol:cma_allocator_alloc
[    0.000000@0]  0, addr:ffffff800971d298 +  140, aml_cma_alloc_post_hook
[    0.000000@0]  1, addr:ffffff800951f258 +   78, dma_alloc_from_contiguous
[    0.000000@0]  2, addr:ffffff80091fdd50 +  388, cma_alloc
[    0.000000@0]  3, addr:ffffff80091f76c8 +  2d0, __kmalloc_track_caller
[    0.000000@0]  4, addr:ffffff80091f4a70 +  2d0, __kmalloc
[    0.000000@0]  5, addr:ffffff80091f4750 +  258, kmem_cache_alloc_trace
[    0.000000@0]  6, addr:ffffff80091f4500 +  250, kmem_cache_alloc
[    0.000000@0]  7, addr:ffffff80091f4490 +   70, __slab_alloc.isra.24.constprop.28
[    0.000000@0]  8, addr:ffffff80091f4108 +  388, ___slab_alloc.constprop.29
[    0.000000@0]  9, addr:ffffff80091f1e70 +  420, new_slab
[    0.000000@0] 10, addr:ffffff80091e52f8 +   b0, vzalloc
[    0.000000@0] 11, addr:ffffff80091e5248 +   b0, vmalloc
[    0.000000@0] 12, addr:ffffff80091e4b00 +  2e0, __vmalloc_node_range
[    0.000000@0] 13, addr:ffffff80091ca410 +  110, kmalloc_order_trace
[    0.000000@0] 14, addr:ffffff80091ca2a0 +  170, kmalloc_order
[    0.000000@0] 15, addr:ffffff80091ab5a8 +  168, __alloc_page_frag
[    0.000000@0] 16, addr:ffffff80091ab540 +   68, alloc_pages_exact
[    0.000000@0] 17, addr:ffffff80091ab510 +   30, get_zeroed_page
[    0.000000@0] 18, addr:ffffff80091ab4b8 +   58, __get_free_pages
[    0.000000@0] 19, addr:ffffff80091aa800 +  cb8, __alloc_pages_nodemask
[    0.000000@0] 20, addr:ffffff800909c6e8 +  2a8, __dma_alloc
[    0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000@0] Preemptible hierarchical RCU implementation.
[    0.000000@0] 	Build-time adjustment of leaf fanout to 64.
[    0.000000@0] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000@0] 
[    0.000000@0] **********************************************************
[    0.000000@0] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
[    0.000000@0] **                                                      **
[    0.000000@0] ** trace_printk() being used. Allocating extra memory.  **
[    0.000000@0] **                                                      **
[    0.000000@0] ** This means that this is a DEBUG kernel and it is     **
[    0.000000@0] ** unsafe for production use.                           **
[    0.000000@0] **                                                      **
[    0.000000@0] ** If you see this message and you are not debugging    **
[    0.000000@0] ** the kernel, report this immediately to your vendor!  **
[    0.000000@0] **                                                      **
[    0.000000@0] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
[    0.000000@0] **********************************************************
[    0.000000@0] NR_IRQS:64 nr_irqs:64 0
[    0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[    0.000000@0] axg_aoclkc_init: register ao clk ok!
[    0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[    0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[    0.000000@0] axg_amlogic_init_media: register meson media clk
[    0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks
[    0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk
[    0.000000@0] axg_clkc_init initialization complete
[    0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.008252@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194
[    0.016909@0] Console: colour dummy device 80x25
[    0.021108@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.031587@0] pid_max: default: 32768 minimum: 301
[    0.036441@0] thread_stack_cache_init, vmap:ffffffc00edaf600, bitmap:ffffffc00eda3000, cache page:ede0
[    0.045773@0] thread_stack_cache_init, allocation vm area:ffffffc00edd94c0, addr:ffffff8020000000, size:20001000
[    0.056006@0] cpu 0, vmap_stack:[ffffffc00f75c960-ffffffc00f760950]
[    0.062304@0] cpu 0, irq_stack: [ffffffc00f753060-ffffffc00f757050]
[    0.068604@0] cpu 1, vmap_stack:[ffffffc00f775960-ffffffc00f779950]
[    0.074904@0] cpu 1, irq_stack: [ffffffc00f76c060-ffffffc00f770050]
[    0.081204@0] cpu 2, vmap_stack:[ffffffc00f78e960-ffffffc00f792950]
[    0.087504@0] cpu 2, irq_stack: [ffffffc00f785060-ffffffc00f789050]
[    0.093804@0] cpu 3, vmap_stack:[ffffffc00f7a7960-ffffffc00f7ab950]
[    0.100104@0] cpu 3, irq_stack: [ffffffc00f79e060-ffffffc00f7a2050]
[    0.106467@0] Security Framework initialized
[    0.110696@0] SELinux:  Initializing.
[    0.114388@0] SELinux:  Starting in permissive mode
[    0.114427@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
[    0.121108@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
[    0.128863@0] ftrace: allocating 30093 entries in 118 pages
[    0.184575@0] sched-energy: CPU device node has no sched-energy-costs
[    0.185388@0] CPU0: update cpu_capacity 1024
[    0.189715@0] ASID allocator initialised with 32768 entries
[    0.227698@0] secmon: can't fine clear_range
[    0.227911@0] EFI services will not be available.
[    0.231181@0] Meson chip version = RevC (25:C - 23:0)
[    0.265048@1] Detected VIPT I-cache on CPU1
[    0.265109@1] CPU1: update cpu_capacity 1024
[    0.265111@1] CPU1: Booted secondary processor [410fd034]
[    0.293113@2] Detected VIPT I-cache on CPU2
[    0.293167@2] CPU2: update cpu_capacity 1024
[    0.293169@2] CPU2: Booted secondary processor [410fd034]
[    0.321172@3] Detected VIPT I-cache on CPU3
[    0.321223@3] CPU3: update cpu_capacity 1024
[    0.321225@3] CPU3: Booted secondary processor [410fd034]
[    0.321316@0] Brought up 4 CPUs
[    0.360535@0] SMP: Total of 4 processors activated.
[    0.365444@0] CPU features: detected feature: 32-bit EL0 Support
[    0.371480@0] CPU features: detected feature: Kernel page table isolation (KPTI)
[    0.382036@0] CPU: All CPU(s) started at EL2
[    0.383219@0] alternatives: patching kernel code
[    0.388545@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755
[    0.395748@0] devtmpfs: initialized
[    0.411022@0] DMI not present or invalid.
[    0.411413@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.419396@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.425977@0] pinctrl core: initialized pinctrl subsystem
[    0.432410@0] NET: Registered protocol family 16
[    0.455917@0] cpuidle: using governor menu
[    0.456432@0] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000)
[    0.462031@0] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers.
[    0.469443@0] DMA: preallocated 256 KiB pool for atomic allocations
[    0.475582@0] clkmsr: clkmsr: driver init
[    0.479633@0] aml_watch_point_probe, in, wp:2
[    0.485105@0] pstore: using zlib compression
[    0.488561@0] console [pstore-1] enabled
[    0.491908@0] pstore: Registered ramoops as persistent store backend
[    0.498323@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0
[    0.512702@0] aml_iomap: amlogic iomap probe done
[    0.519724@0] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c
[    0.521653@0] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0
[    0.622007@0] usbcore: registered new interface driver usbfs
[    0.622181@0] usbcore: registered new interface driver hub
[    0.627811@0] usbcore: registered new device driver usb
[    0.633090@0] pps_core: LinuxPPS API ver. 1 registered
[    0.638034@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.647412@0] PTP clock support registered
[    0.651762@0] dmi: Firmware registration failed.
[    0.656771@0] secmon: reserve_mem_size:0x300000
[    0.660774@0] secmon secmon: assigned reserved memory node linux,secmon
[    0.667728@0] secmon: get page:ffffffbf00140000, 5000
[    0.672384@0] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000
[    0.680786@0] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
[    0.688691@0] NetLabel: Initializing
[    0.690824@0] NetLabel:  domain hash size = 128
[    0.695426@0] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.700649@0] NetLabel:  unlabeled traffic allowed by default
[    0.707291@0] clocksource: Switched to clocksource arch_sys_counter
[    0.837565@0] VFS: Disk quotas dquot_6.6.0
[    0.837712@0] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.864692@0] NET: Registered protocol family 2
[    0.865740@0] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.870943@0] TCP bind hash table entries: 2048 (order: 3, 32768 bytes)
[    0.877673@3] TCP: Hash tables configured (established 2048 bind 2048)
[    0.884375@3] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.890145@3] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.896930@3] NET: Registered protocol family 1
[    0.901953@3] RPC: Registered named UNIX socket transport module.
[    0.907320@3] RPC: Registered udp transport module.
[    0.912194@3] RPC: Registered tcp transport module.
[    0.917065@3] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.926258@3] Unpacking initramfs...
[    1.431055@2] Initramfs unpacking failed: junk in compressed archive
[    1.437964@2] Freeing initrd memory: 6560K
[    1.438914@2] hw perfevents: clusterb_enabled = 0
[    1.441224@2] hw perfevents: cpumasks 0xf, 0x0
[    1.445667@2] hw perfevents: cluster A irq = 7
[    1.450232@2] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    1.460470@2] audit: initializing netlink subsys (disabled)
[    1.463791@2] audit: type=2000 audit(1.280:1): initialized
[    1.471084@2] workingset: timestamp_bits=62 max_order=16 bucket_order=0
[    1.495650@2] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.498657@2] NFS: Registering the id_resolver key type
[    1.501369@2] Key type id_resolver registered
[    1.505680@2] Key type id_legacy registered
[    1.510312@2] fuse init (API version 7.26)
[    1.515811@2] SELinux:  Registering netfilter hooks
[    1.522045@2] NET: Registered protocol family 38
[    1.522107@2] Key type asymmetric registered
[    1.525351@2] Asymmetric key parser 'x509' registered
[    1.530855@2] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    1.538045@2] io scheduler noop registered (default)
[    1.543020@2] io scheduler deadline registered
[    1.547906@2] io scheduler cfq registered
[    1.568650@3] random: fast init done
[    1.568748@3] random: crng init done
[    1.569218@2] Unable to detect cache hierarchy for CPU 0
[    1.609892@2] loop: module loaded
[    1.615529@2] zram: Added device: zram0
[    1.615965@2] mtdoops: mtd device (mtddev=name/number) must be supplied
[    1.620982@2] libphy: Fixed MDIO Bus: probed
[    1.626416@2] tun: Universal TUN/TAP device driver, 1.6
[    1.629953@2] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.638154@2]  ee eth reset:Addr = ffffff80081fd008
[    1.645669@2] meson6-dwmac ff3f0000.ethernet: no reset control found
[    1.647628@2] stmmac - user ID: 0x11, Synopsys ID: 0x37
[    1.652863@2]  Ring mode enabled
[    1.656091@2]  DMA HW capability register supported
[    1.660824@2]  Normal descriptors
[    1.664140@2]  RX Checksum Offload Engine supported
[    1.669043@2] 	COE Type 2
[    1.671666@2]  TX Checksum insertion supported
[    1.676134@2]  Wake-Up On Lan supported
[    1.680074@2]  Enable RX Mitigation via HW Watchdog Timer
[    1.693642@2] libphy: stmmac: probed
[    1.693694@2] eth%d: PHY ID 0007c0f1 at 0 IRQ POLL (stmmac-0:00) active
[    1.700222@2] PPP generic driver version 2.4.2
[    1.703084@2] PPP BSD Compression module registered
[    1.707629@2] PPP Deflate Compression module registered
[    1.712887@2] PPP MPPE Compression module registered
[    1.717843@2] NET: Registered protocol family 24
[    1.723367@2] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.729229@2] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.736308@2] usbcore: registered new interface driver cdc_acm
[    1.741481@2] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.749912@2] usbcore: registered new interface driver usbserial
[    1.756613@2] mousedev: PS/2 mouse device common for all mice
[    1.762046@2] usbcore: registered new interface driver xpad
[    1.767466@2] i2c /dev entries driver
[    1.772187@2] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
[    1.776443@2] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
[    1.787515@2] ff803000.serial: clock gate not found
[    1.788950@2] meson_uart ff803000.serial: ==uart0 reg addr = ffffff800830d000
[    1.796214@2] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 13, base_baud = 1500000) is a meson_uart
[    1.811101@2] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200
[    1.813802@2] console [ttyS0] enabled
[    1.821032@2] bootconsole [aml_uart0] disabled
[    1.830686@3] ff804000.serial: clock gate not found
[    1.834815@3] meson_uart ff804000.serial: ==uart3 reg addr = ffffff8008321000
[    1.841936@3] ff804000.serial: ttyS3 at MMIO 0xff804000 (irq = 14, base_baud = 1500000) is a meson_uart
[    1.852322@0] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff8008323000
[    1.858431@0] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 25, base_baud = 1500000) is a meson_uart
[    1.868624@2] meson_uart ffd23000.serial: ==uart2 reg addr = ffffff8008325000
[    1.874877@2] ffd23000.serial: ttyS2 at MMIO 0xffd23000 (irq = 26, base_baud = 1500000) is a meson_uart
[    1.885901@0] amlogic-new-usb2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff8008348000
[    1.895152@0] amlogic-new-usb3 ffe09080.usb3phy: This phy has no usb port
[    1.901633@0] amlogic-new-usb3 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff800834c080
[    1.916770@3] i2c i2c-1: of_i2c: modalias failure on /soc/aobus@ff800000/i2c@5000/mcu6350@40
[    1.920474@3] i2c i2c-1: Failed to create I2C device for /soc/aobus@ff800000/i2c@5000/mcu6350@40
[    1.932955@3] aml_dma ff63e000.aml_dma: Aml dma
[    1.935978@3] aml_aes_dma ff63e000.aml_dma:aml_aes: Aml AES_dma
[    1.940959@3] aml_sha_dma ff63e000.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma
[    1.947350@3] efusekeynum: 4
[    1.949648@3] efusekeyname:             mac	offset:     0	size:     6
[    1.956085@3] efusekeyname:          mac_bt	offset:     6	size:     6
[    1.962498@3] efusekeyname:        mac_wifi	offset:    12	size:     6
[    1.968908@3] efusekeyname:            usid	offset:    18	size:    16
[    1.975756@0] efuse efuse: probe OK!
[    1.981227@0] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller
[    1.988452@2] meson-mmc: >>>>>>>>hostbase ffffff8008358000, dmode 
[    1.993506@2] meson-mmc: actual_clock :400000, HHI_nand: 0x80
[    1.998726@2] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c
[    2.043435@2] meson-mmc: meson_mmc_probe() : success!
[    2.043699@2] amlogic mtd driver init
[    2.047792@2] prase_get_dtb_nand_parameter:128,parse dts start
[    2.052516@2] bl mode descrete
[    2.055389@2] fip_copies 4
[    2.058054@2] fip_size 0x200000
[    2.061194@2] nand_clk_ctrl 0xffe07000
[    2.064918@2] prase_get_dtb_nand_parameter:234,parse dts end
[    2.070587@2] nand_clk_ctrl 0xffe07000
[    2.074306@2] nand register base ffffff80083df800, nand clock register ffffff80083e1000
[    2.083054@2] plat->aml_nand_device ffffff800a005c10
[    2.087203@2] m3_nand_probe() aml_nand_device ffffff800a005c10
[    2.093268@2] NAND device id: 2c da 90 95 6 0
[    2.097342@2] NAND device: Manufacturer ID: 
[    2.101408@2]  0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
[    2.108451@2] oob_fill_cnt =32 oob_size =64, bch_bytes =14
[    2.113884@2] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
[    2.119432@2] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
[    2.125677@2] mtd->oobavail: 0x8
[    2.129095@2] aml_nand_init 2119: plat-name:bootloader
[    2.133999@2] Creating 1 MTD partitions on "bootloader":
[    2.139295@2] 0x000000000000-0x000000200000 : "bootloader"
[    2.148469@3] bootloader initialized ok
[    2.148573@3] plat->aml_nand_device ffffff800a005c10
[    2.153521@3] m3_nand_probe() aml_nand_device ffffff800a005c10
[    2.159660@3] NAND device id: 2c da 90 95 6 0
[    2.163643@3] NAND device: Manufacturer ID: 
[    2.167715@3]  0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
[    2.174751@3] oob_fill_cnt =32 oob_size =64, bch_bytes =14
[    2.180192@3] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
[    2.185732@3] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
[    2.191985@3] mtd->oobavail: 0x8
[    2.195456@3] aml_nand_init 2119: plat-name:nandnormal
[    2.200363@3] bbt_start=20
[    2.202959@3] env_start=24
[    2.205667@3] key_start=32
[    2.208350@3] dtb_start=40
[    2.211018@3] ddr_start=44
[    2.213723@3] nbbt: info size=0x800 max_scan_blk=24, start_blk=20
[    2.220219@3] get_free_node 43: bitmap=0
[    2.223692@3] get_free_node 55: bitmap=1
[    2.227783@3] get_free_node 43: bitmap=1
[    2.231491@3] get_free_node 55: bitmap=3
[    2.235583@3] get_free_node 43: bitmap=3
[    2.239290@3] get_free_node 55: bitmap=7
[    2.243174@3] nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1
[    2.249870@3] nbbt free list:
[    2.252811@3] blockN=21, ec=-1, dirty_flag=0
[    2.257056@3] blockN=22, ec=-1, dirty_flag=0
[    2.261302@3] blockN=23, ec=-1, dirty_flag=0
[    2.265550@3] aml_nand_scan_rsv_info 1141: page_num=1
[    2.270959@3] nbbt valid addr: 280000
[    2.274218@3] aml_nand_bbt_check 1306 bbt is valid, reading.
[    2.279852@3] aml_nand_read_rsv_info:423,read nbbt info at 280000
[    2.286112@3] nenv: info size=0x10000 max_scan_blk=32, start_blk=24
[    2.292540@3] get_free_node 43: bitmap=7
[    2.296058@3] get_free_node 55: bitmap=f
[    2.300148@3] get_free_node 43: bitmap=f
[    2.303858@3] get_free_node 55: bitmap=1f
[    2.308035@3] get_free_node 43: bitmap=1f
[    2.311831@3] get_free_node 55: bitmap=3f
[    2.316008@3] get_free_node 43: bitmap=3f
[    2.319804@3] get_free_node 55: bitmap=7f
[    2.323982@3] get_free_node 43: bitmap=7f
[    2.327778@3] get_free_node 55: bitmap=ff
[    2.331954@3] get_free_node 43: bitmap=ff
[    2.335751@3] get_free_node 55: bitmap=1ff
[    2.340015@3] get_free_node 43: bitmap=1ff
[    2.343896@3] get_free_node 55: bitmap=3ff
[    2.347971@3] nenv : phy_blk_addr=24, ec=0, phy_page_addr=0, timestamp=1
[    2.354641@3] nenv free list:
[    2.357589@3] blockN=25, ec=-1, dirty_flag=0
[    2.361836@3] blockN=26, ec=-1, dirty_flag=0
[    2.366082@3] blockN=27, ec=-1, dirty_flag=0
[    2.370329@3] blockN=28, ec=-1, dirty_flag=0
[    2.374575@3] blockN=29, ec=-1, dirty_flag=0
[    2.378822@3] blockN=30, ec=-1, dirty_flag=0
[    2.383069@3] blockN=31, ec=-1, dirty_flag=0
[    2.387316@3] aml_nand_scan_rsv_info 1141: page_num=32
[    2.404557@3] nenv valid addr: 310000
[    2.404590@3] nkey: info size=0x8000 max_scan_blk=40, start_blk=32
[    2.408950@3] get_free_node 43: bitmap=3ff
[    2.412832@3] get_free_node 55: bitmap=7ff
[    2.417096@3] get_free_node 43: bitmap=7ff
[    2.420979@3] get_free_node 55: bitmap=fff
[    2.425243@3] get_free_node 43: bitmap=fff
[    2.429125@3] get_free_node 55: bitmap=1fff
[    2.433476@3] get_free_node 43: bitmap=1fff
[    2.437445@3] get_free_node 55: bitmap=3fff
[    2.441796@3] get_free_node 43: bitmap=3fff
[    2.445765@3] get_free_node 55: bitmap=7fff
[    2.450116@3] get_free_node 43: bitmap=7fff
[    2.454085@3] get_free_node 55: bitmap=ffff
[    2.458437@3] get_free_node 43: bitmap=ffff
[    2.462405@3] get_free_node 55: bitmap=1ffff
[    2.466842@3] get_free_node 43: bitmap=1ffff
[    2.470899@3] get_free_node 55: bitmap=3ffff
[    2.475143@3] nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
[    2.481816@3] nkey free list:
[    2.484763@3] blockN=32, ec=-1, dirty_flag=0
[    2.489010@3] blockN=33, ec=-1, dirty_flag=0
[    2.493257@3] blockN=34, ec=-1, dirty_flag=0
[    2.497504@3] blockN=35, ec=-1, dirty_flag=0
[    2.501750@3] blockN=36, ec=-1, dirty_flag=0
[    2.506003@3] blockN=37, ec=-1, dirty_flag=0
[    2.510244@3] blockN=38, ec=-1, dirty_flag=0
[    2.514490@3] blockN=39, ec=-1, dirty_flag=0
[    2.518737@3] aml_nand_scan_rsv_info 1141: page_num=16
[    2.523851@3] nkey valid addr: fffffffffffe0000
[    2.528357@3] aml_nand_key_check 1251 NO key exist
[    2.533125@3] ndtb: info size=0x20000 max_scan_blk=44, start_blk=40
[    2.539746@3] get_free_node 43: bitmap=3ffff
[    2.543613@3] get_free_node 55: bitmap=7ffff
[    2.548049@3] get_free_node 43: bitmap=7ffff
[    2.552105@3] get_free_node 55: bitmap=fffff
[    2.556543@3] get_free_node 43: bitmap=fffff
[    2.560599@3] get_free_node 55: bitmap=1fffff
[    2.564932@3] ndtb : phy_blk_addr=40, ec=0, phy_page_addr=0, timestamp=1
[    2.571603@3] ndtb free list:
[    2.574533@3] blockN=41, ec=-1, dirty_flag=0
[    2.578797@3] blockN=42, ec=-1, dirty_flag=0
[    2.583043@3] blockN=43, ec=-1, dirty_flag=0
[    2.587292@3] aml_nand_scan_rsv_info 1141: page_num=64
[    2.604517@3] ndtb valid addr: 500000
[    2.604550@3] nddr: info size=0x20000 max_scan_blk=46, start_blk=44
[    2.608994@3] get_free_node 43: bitmap=1fffff
[    2.613136@3] get_free_node 55: bitmap=3fffff
[    2.617660@3] get_free_node 43: bitmap=3fffff
[    2.621803@3] get_free_node 55: bitmap=7fffff
[    2.626136@3] nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
[    2.632806@3] nddr free list:
[    2.635754@3] blockN=44, ec=-1, dirty_flag=0
[    2.640001@3] blockN=45, ec=-1, dirty_flag=0
[    2.644248@3] aml_nand_scan_rsv_info 1141: page_num=64
[    2.649358@3] nddr valid addr: fffffffffffe0000
[    2.653868@3] aml_nand_ddr_check 1281 NO ddr exist
[    2.658638@3] tpl: off 8388608, size 8388608
[    2.789967@3] Creating 6 MTD partitions on "nandnormal":
[    2.790014@3] 0x000000800000-0x000001000000 : "tpl"
[    2.801029@3] 0x000001000000-0x000001200000 : "misc"
[    2.804172@2] 0x000001200000-0x000002200000 : "recovery"
[    2.816245@0] 0x000002200000-0x000004200000 : "boot"
[    2.835355@0] 0x000004200000-0x000004700000 : "config"
[    2.840091@0] 0x000004700000-0x000010000000 : "nvdata"
[    2.940674@2] nandnormal initialized ok
[    2.940785@2] aml_ubootenv_init: register env chardev
[    2.944519@2] aml_ubootenv_init: register env chardev OK
[    2.949364@2] amlnf_dtb_init: register dtb cdev
[    2.954299@2] amlnf_dtb_init: register dtd cdev OK
[    2.958531@2] mtd_nand_probe 267 , err = 0
[    2.963741@1] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc0
[    2.969132@1] input: aml_vkeypad as /devices/platform/rtc/input/input0
[    2.976186@1] unifykey: storage in base: 0xffffffc005000000
[    2.980714@1] unifykey: storage out base: 0xffffffc005040000
[    2.986317@1] unifykey: storage block base: 0xffffffc005080000
[    2.992131@1] unifykey: probe done!
[    2.996321@1] unifykey: no efuse-version set, use default value: -1
[    3.001848@1] unifykey: key unify config unifykey-num is 6
[    3.007434@1] unifykey: key unify fact unifykey-num is 6
[    3.012666@1] unifykey: unifykey_devno: f200000
[    3.017776@1] unifykey: device unifykeys created ok
[    3.022110@1] unifykey: aml_unifykeys_init done!
[    3.026972@1] sysled: module init
[    3.030455@1] meson_wdt ffd0f0d0.watchdog: start watchdog
[    3.035217@1] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog
[    3.042767@0] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done
[    3.051422@3] dmc_monitor_probe
[    3.052228@3] page_trace_module_init, create sysfs failed
[    3.058126@3] defendkey defendkey: Reserved memory is not enough!
[    3.063368@3] defendkey: probe of defendkey failed with error -22
[    3.069708@3] GACT probability NOT on
[    3.073018@3] Mirror/redirect action on
[    3.076816@3] u32 classifier
[    3.079654@3]     Actions configured
[    3.083194@3] Netfilter messages via NETLINK v0.30.
[    3.088494@3] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[    3.094704@3] ctnetlink v0.93: registering with nfnetlink.
[    3.100724@3] xt_time: kernel timezone is -0000
[    3.104282@3] ipip: IPv4 and MPLS over IPv4 tunneling driver
[    3.110940@3] ip_tables: (C) 2000-2006 Netfilter Core Team
[    3.115681@3] arp_tables: arp_tables: (C) 2002 David S. Miller
[    3.121101@3] Initializing XFRM netlink socket
[    3.126630@3] NET: Registered protocol family 10
[    3.132591@3] mip6: Mobile IPv6
[    3.133158@3] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    3.139171@3] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    3.147190@3] NET: Registered protocol family 17
[    3.149412@3] NET: Registered protocol family 15
[    3.154008@3] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    3.167153@3] l2tp_core: L2TP core driver, V2.0
[    3.171547@3] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[    3.176464@3] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[    3.182217@3] l2tp_netlink: L2TP netlink interface
[    3.187010@3] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[    3.193089@3] l2tp_debugfs: L2TP debugfs support
[    3.197626@3] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[    3.204262@3] NET: Registered protocol family 35
[    3.209199@3] Key type dns_resolver registered
[    3.213790@3] Registered swp emulation handler
[    3.217651@3] Registered cp15_barrier emulation handler
[    3.222841@3] Registered setend emulation handler
[    3.227585@3] disable EAS feature
[    3.232351@2] registered taskstats version 1
[    3.249420@2] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host
[    3.755866@2] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.755962@2] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    3.764326@2] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f664 hci version 0x100 quirks 0x02010010
[    3.772695@2] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0xff500000
[    3.780305@1] hub 1-0:1.0: USB hub found
[    3.782597@1] hub 1-0:1.0: 1 port detected
[    3.787300@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.792257@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    3.800168@1] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.809671@3] hub 2-0:1.0: USB hub found
[    3.812264@3] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    3.819547@3] usb usb2: Unsupported the hub
[    3.824402@3] aml_vrtc rtc: setting system clock to 2022-08-18 20:16:34 UTC (1660853794)
[    3.832391@3] dwc_otg ff400000.dwc2_a: dwc_otg_driver_probe(ffffffc00e1a7000)
[    3.832468@3] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0
[    3.840356@3] dwc_otg ff400000.dwc2_a: base=0xffffff8008580000
[    3.840369@3] dwc_otg ff400000.dwc2_a: dwc_otg_device=0xffffffc00c3dac00
[    3.940816@1] dwc_otg: Core Release: 3.10a
[    3.940872@1] dwc_otg: Setting default values for core params
[    3.945065@1] dwc_otg: curmode: 0, host_only: 0
[    3.949569@1] dwc_otg ff400000.dwc2_a: DMA config: BURST_DEFAULT
[    3.962096@1] dwc_otg: Using Buffer DMA mode
[    3.962135@1] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[    3.966038@1] dwc_otg: Working on port type = SLAVE
[    3.970895@1] dwc_otg: Dedicated Tx FIFOs mode
[    3.978209@0] thermal thermal_zone0: binding zone soc_thermal with cdev thermal-cpufreq-0 failed:-22
[    3.984622@0] cpucore_cooling_register, max_cpu_core_num:4
[    3.997201@0] gxbb_pm: enter meson_pm_probe!
[    3.997258@0] no vddio3v3_en pin
[    3.998909@0] pm-meson aml_pm: Can't get switch_clk81
[    4.004021@0] gxbb_pm: meson_pm_probe done
[    4.008966@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
[    4.015320@0] Freeing unused kernel memory: 3648K
[    4.030133@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
[    4.293691@1] ubi0: attaching mtd5
[    4.312358@1] ubi0: scanning is finished
[    4.317124@2] ubi0: attached mtd5 (name "config", size 5 MiB)
[    4.317254@2] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    4.324328@2] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    4.331224@2] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    4.338335@2] ubi0: good PEBs: 40, bad PEBs: 0, corrupted PEBs: 0
[    4.344396@2] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[    4.351766@2] ubi0: max/mean erase counter: 17/9, WL threshold: 4096, image sequence number: 3840799589
[    4.361117@2] ubi0: available PEBs: 0, total reserved PEBs: 40, PEBs reserved for bad PEB handling: 4
[    4.370337@1] ubi0: background thread "ubi_bgt0d" started, PID 1076
[    4.383682@0] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 1080
[    4.400199@3] UBIFS (ubi0:0): recovery needed
[    4.448655@1] UBIFS (ubi0:0): recovery completed
[    4.448933@1] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "config_data"
[    4.455666@1] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    4.465703@1] UBIFS (ubi0:0): FS size: 2793472 bytes (2 MiB, 22 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[    4.475925@1] UBIFS (ubi0:0): reserved for root: 131942 bytes (128 KiB)
[    4.482515@1] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 2B90057A-F1F9-40D0-8AE4-E79C5C9C41F3, small LPT model
[    4.506958@2] ubi2: attaching mtd6
[    5.179401@2] ubi2: scanning is finished
[    5.186432@0] ubi2: attached mtd6 (name "nvdata", size 185 MiB)
[    5.186738@0] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    5.193795@0] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    5.200715@0] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096
[    5.207809@0] ubi2: good PEBs: 1480, bad PEBs: 0, corrupted PEBs: 0
[    5.214055@0] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128
[    5.221423@0] ubi2: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 893030469
[    5.230609@0] ubi2: available PEBs: 0, total reserved PEBs: 1480, PEBs reserved for bad PEB handling: 4
[    5.239988@3] ubi2: background thread "ubi_bgt2d" started, PID 1087
[    5.253318@0] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 1091
[    5.269923@2] UBIFS (ubi2:0): recovery needed
[    5.325618@2] UBIFS (ubi2:0): recovery completed
[    5.325903@2] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "nvdata_data"
[    5.332648@2] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    5.342667@2] UBIFS (ubi2:0): FS size: 185384960 bytes (176 MiB, 1460 LEBs), journal size 9269248 bytes (8 MiB, 73 LEBs)
[    5.353495@2] UBIFS (ubi2:0): reserved for root: 4952683 bytes (4836 KiB)
[    5.360258@2] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID 6342A654-D0BF-4E56-9003-8D30EC1F1628, small LPT model
[    5.633151@1] eth0: device MAC address 02:05:c3:a0:e5:c4
[    5.716965@0] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP.
[    5.718230@0] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    5.934891@3] uart_trans: loading out-of-tree module taints kernel.
[    5.937394@3] register uart_trans chrdev success.
[    5.940665@3] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 0 to 9600
[    5.948280@3] tty port open success [/dev/ttyS3]!
[    5.952914@3] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 9600 to 115200
[    5.961454@3] init sucess for tty struct (246:3)  [/dev/ttyS3]
[    5.967486@3] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 0 to 9600
[    5.975103@3] tty port open success [/dev/ttyS2]!
[    5.979782@3] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 9600 to 115200
[    5.988171@3] init sucess for tty struct (246:2)  [/dev/ttyS2]
[    5.994266@3] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 0 to 9600
[    6.001952@3] tty port open success [/dev/ttyS1]!
[    6.006628@3] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 115200
[    6.015033@3] init sucess for tty struct (246:1)  [/dev/ttyS1]
[    6.021098@0] create workqueue success!
[    7.767554@0] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
[    7.770677@0] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   26.507049@2] uart trans dev open.
[   26.507156@2] uart_buf virt addr = 0xffffffc00bd40000
[   26.509928@2] uart_buf phys addr = 0x0bd40000
[   26.514219@2] uart_buf pfn       = 0x0000bd40
[   26.518883@2] uart trans stop send work timer.
[   26.523160@2] uart trans set chain exist bits:0x7.
[   26.527781@2] uart trans set work queue count 768.
[  213.201813@3] uart trans stop send work timer.
[  216.203883@3] uart trans stop send work timer.
[  257.105609@2] uart trans start send work timer.


===========================================Miner log===========================================
2022-08-18 20:16:41 Open miner sn file /config/sn error
2022-08-18 20:16:41 Miner compile time: Tue Mar 29 13:30:04 CST 2022 type: Antminer BHB42XXX sn :
2022-08-18 20:16:42 This is fix-freq version
2022-08-18 20:16:42 Miner compile time: Tue Mar 29 13:30:04 CST 2022 type: Antminer BHB42XXX
2022-08-18 20:16:42 commit version: 1956e61 2022-03-29 13:26:30, build by: jenkins 2022-03-29 13:52:24
2022-08-18 20:16:42 opt_multi_version     = 1
2022-08-18 20:16:42 opt_bitmain_ab        = 1
2022-08-18 20:16:42 mid_auto_gen          = 1
2022-08-18 20:16:42 opt_bitmain_work_mode = 0
2022-08-18 20:16:42 port 439 already exported
2022-08-18 20:16:42 port 454 already exported
2022-08-18 20:16:42 port 440 already exported
2022-08-18 20:16:42 port 455 already exported
2022-08-18 20:16:42 port 441 already exported
2022-08-18 20:16:42 port 456 already exported
2022-08-18 20:16:42 port 438 already exported
2022-08-18 20:16:42 port 453 already exported
2022-08-18 20:16:42 port 446 already exported
2022-08-18 20:16:42 port 445 already exported
2022-08-18 20:16:42 Note: front fan is power on!
2022-08-18 20:16:42 Note: rear fan is power on!
2022-08-18 20:16:42 start the http log.
2022-08-18 20:16:42 httpListenThread start ret=0
2022-08-18 20:16:42 start listen on 6060 ...
2022-08-18 20:16:42 bad chain id = 3
2022-08-18 20:16:45 bad chain id = 3
2022-08-18 20:16:47 ==========================capability start==========================
2022-08-18 20:16:47 board num = 3
2022-08-18 20:16:47 board id = 0, chain num = 1
2022-08-18 20:16:47 	chain id = 0
2022-08-18 20:16:47 board id = 1, chain num = 1
2022-08-18 20:16:47 	chain id = 1
2022-08-18 20:16:47 board id = 2, chain num = 1
2022-08-18 20:16:47 	chain id = 2
2022-08-18 20:16:47 ==========================capability end============================
2022-08-18 20:16:47 chain num = 3
2022-08-18 20:16:47 skip loading levels for now
2022-08-18 20:16:48 load chain 0 eeprom data
2022-08-18 20:16:48 bad_asic_crc = 4,buf[SWEEP_INFO_CRC_OFFSET] = 214
2022-08-18 20:16:48 EEPROM error: CRC 3ND REGION
2022-08-18 20:16:49 load chain 1 eeprom data
2022-08-18 20:16:49 bad_asic_crc = 4,buf[SWEEP_INFO_CRC_OFFSET] = 214
2022-08-18 20:16:49 EEPROM error: CRC 3ND REGION
2022-08-18 20:16:49 load chain 2 eeprom data
2022-08-18 20:16:49 bad_asic_crc = 4,buf[SWEEP_INFO_CRC_OFFSET] = 214
2022-08-18 20:16:49 EEPROM error: CRC 3ND REGION
2022-08-18 20:16:49 i2c_sim_init start
2022-08-18 20:16:49 init gpio477
2022-08-18 20:16:49 init gpio476
2022-08-18 20:16:49 i2c_sim_init end
2022-08-18 20:16:51 power open power_version = 0x75
2022-08-18 20:16:56 get power version failed
2022-08-18 20:16:56 power is not Calibrated
2022-08-18 20:16:57 updated miner type to: Antminer S19j Pro
2022-08-18 20:16:57 multi machine mode
2022-08-18 20:16:57 load machine BHB42631 conf
2022-08-18 20:16:57 machine : BHB42631 
2022-08-18 20:16:57 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2022-08-18 20:16:57 fan_eft : 0  fan_pwm : 100
2022-08-18 20:16:57 create thread get_nonce_and_register_thread
2022-08-18 20:16:57 fixed working voltage = 1360
2022-08-18 20:16:57 Chain [0] PCB Version: 0x0120
2022-08-18 20:16:57 Chain [0] BOM Version: 0x0020
2022-08-18 20:16:57 Chain [1] PCB Version: 0x0120
2022-08-18 20:16:57 Chain [1] BOM Version: 0x0020
2022-08-18 20:16:57 Chain [2] PCB Version: 0x0120
2022-08-18 20:16:57 Chain [2] BOM Version: 0x0020
2022-08-18 20:16:57 bad chain id = 3
2022-08-18 20:16:57 Fan check passed.
2022-08-18 20:16:57 uart_trans addr:0xf72bd000.
2022-08-18 20:16:57 max sensor num = 4
2022-08-18 20:16:57 STATUS_INITED: soc init done!
2022-08-18 20:16:57 temperature_monitor_thread start...
2022-08-18 20:17:46 reload pool, need recalculate
2022-08-18 20:17:46 set_start_time_point total_tv_start_sys=76 total_tv_end_sys=77
2022-08-18 20:17:47 start to init...
2022-08-18 20:17:49 power type version: 0x0075
2022-08-18 20:17:50 disable power watchdog: 0x0000
2022-08-18 20:17:51 Enter sleep to make sure power release finish.
2022-08-18 20:18:22 Slept 30 seconds, diff = 2.
2022-08-18 20:18:26 set_voltage_by_steps to 1500.
2022-08-18 20:18:31 chain avg vol drop from 1500 to 0.00
2022-08-18 20:18:31 power voltage can not meet the target
2022-08-18 20:18:33 chain avg vol drop from 1500 to 0.00
2022-08-18 20:18:33 power voltage can not meet the target
2022-08-18 20:18:36 chain avg vol drop from 1500 to 0.00
2022-08-18 20:18:36 power voltage can not meet the target
2022-08-18 20:18:54 bitmain_get_power_status failed!
2022-08-18 20:19:15 bitmain_get_power_status failed!
2022-08-18 20:19:36 bitmain_get_power_status failed!
2022-08-18 20:19:58 bitmain_get_power_status failed!
2022-08-18 20:20:01 Sweep error string = V:1.
2022-08-18 20:20:01 ERROR_POWER_LOST: get power type version failed!
2022-08-18 20:20:01 stop_mining: get power type version failed!
2022-08-18 20:20:01 uninit_temp_info
2022-08-18 20:20:01 do not read temp anymore...
2022-08-18 20:20:01 cancel thread
2022-08-18 20:20:01 ****power off hashboard****
2022-08-18 20:20:01 temp monitor thread exit
2022-08-18 20:20:04 ERROR_SOC_INIT: soc init failed!
2022-08-18 20:20:04 stop_mining: soc init failed!
2022-08-18 20:20:04 ****power off hashboard****
2022-08-18 20:20:48 Version num 65536
2022-08-18 20:20:48 Mask num 0x1fffe000
2022-08-18 20:20:48 Note: addrInterval or corenum is not initialized.