S11 wont hash

Hi

I have a Antminer S11 that wont hash. Any idea what could be the reason?

Thanx for any reply.

Regards Arve

Kernel log:

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 199096K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 30280K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 17240K (cca2b000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 2102/1450, WL threshold: 4096, image sequence number: 1246466207
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 2EA29CDC-48E8-49E4-90AC-CEC6C574A5B0, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 61044873
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 817D08AA-A111-4DF5-B35B-209F04D5A0EB, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab00d
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
main.c:13999: log_level = 4
main.c:14026: This is XILINX board. Totalram: 239353856
main.c:14044: Detect 256MB control board of XILINX
driver-bitmain.c:1777: mmap axi_fpga_addr = 0xb6ffa000
driver-bitmain.c:1782: axi_fpga_addr data = 0xb00d
driver-bitmain.c:1798: mmap fpga_mem_addr = 0xb5dfe000
driver-bitmain.c:995: forceFreq=-1 forceFlag=0
driver-bitmain.c:1697: min work minertest[0]:912

main.c:8490: DETECT HW version=000ab00d
main.c:14071: miner ID : 812c342a7910481c
main.c:14100: Miner Type = S9+
main.c:14108: AsicType = 1387
main.c:14111: real AsicNum = 84
main.c:14204: use critical mode to search freq...
driver-bitmain.c:1877: get PLUG ON=0x00000007
driver-bitmain.c:1947: Find hashboard on Chain[0]
driver-bitmain.c:1947: Find hashboard on Chain[1]
driver-bitmain.c:1947: Find hashboard on Chain[2]
main.c:2148: chain[0] PIC jump to app
main.c:2153: Check chain[0] PIC fw version=0xa4
main.c:2148: chain[1] PIC jump to app
main.c:2153: Check chain[1] PIC fw version=0xa4
main.c:2148: chain[2] PIC jump to app
main.c:2153: Check chain[2] PIC fw version=0xa4
main.c:8805: Chain[0] read_freq_badcores : 0x7d 0xd9 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x2f 0x1a 0x00 0x00 0xc8 0xef 0xfe 0xfa 0xef 0xeb 0xbf 0xaf 0xbf 0xbf 0xbe 0xef 0xef 0xfb 0xee 0xbf 0xfe 0xfe 0xee 0xfb 0xeb 0xbf 0x5c 0x13 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
main.c:8817: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8836: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8923: has freq in PIC, will disable freq setting.
main.c:8997: chain[0] has freq in PIC and will jump over...
main.c:8999: Chain[0] has core num in PIC
main.c:8805: Chain[1] read_freq_badcores : 0x7d 0xd9 0x4e 0x56 0x52 0x56 0x52 0x4e 0x56 0x52 0x4e 0x56 0x52 0x4e 0x4e 0x52 0x56 0x4e 0x56 0x52 0x56 0x52 0x4e 0x56 0x52 0x4e 0x4e 0x56 0x52 0x56 0x4e 0x52 0x4e 0x52 0x56 0x4e 0x56 0x52 0x56 0x4e 0x52 0x56 0x4e 0x52 0x56 0x4e 0x52 0x4e 0x56 0x52 0x56 0x4e 0x52 0x52 0x4e 0x56 0x56 0x4e 0x52 0x4e 0x52 0x56 0x56 0x52 0x4e 0x4e 0x52 0x56 0x52 0x4e 0x56 0x52 0x56 0x4e 0x4e 0x52 0x56 0x4e 0x56 0x52 0x56 0x4e 0x52 0x4e 0x56 0x52 0xb4 0x19 0x00 0x00 0xc8 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0x3f 0xff 0xcf 0xff 0xff 0xff 0xff 0xff 0x93 0x0b 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
main.c:8817: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8836: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8923: has freq in PIC, will disable freq setting.
main.c:8997: chain[1] has freq in PIC and will jump over...
main.c:8999: Chain[1] has core num in PIC
main.c:8805: Chain[2] read_freq_badcores : 0x7d 0xd9 0x5a 0x56 0x52 0x52 0x5a 0x56 0x5a 0x56 0x52 0x52 0x56 0x5a 0x56 0x52 0x5a 0x5a 0x52 0x56 0x56 0x52 0x5a 0x52 0x5a 0x56 0x56 0x52 0x5a 0x5a 0x56 0x52 0x52 0x5a 0x56 0x52 0x56 0x5a 0x5a 0x52 0x56 0x56 0x52 0x5a 0x56 0x52 0x5a 0x52 0x5a 0x56 0x5a 0x52 0x56 0x56 0x52 0x5a 0x5a 0x52 0x56 0x56 0x5a 0x52 0x5a 0x52 0x56 0x56 0x5a 0x52 0x52 0x5a 0x56 0x52 0x56 0x5a 0x5a 0x56 0x52 0x56 0x5a 0x52 0x52 0x56 0x5a 0x5a 0x56 0x52 0x70 0x1a 0x00 0x00 0xc8 0xfd 0xdd 0x7f 0x5f 0xff 0xdd 0x5f 0x7f 0x7f 0x7d 0xdf 0xdf 0x7d 0xdf 0xdf 0xfd 0x7d 0x7f 0xfd 0xfd 0xf5 0xb6 0x13 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
main.c:8817: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8836: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
main.c:8923: has freq in PIC, will disable freq setting.
main.c:8997: chain[2] has freq in PIC and will jump over...
main.c:8999: Chain[2] has core num in PIC
main.c:9103: get PIC voltage=0 on chain[0], value=930
main.c:9103: get PIC voltage=0 on chain[1], value=930
main.c:9103: get PIC voltage=4 on chain[2], value=910
main.c:9269: chain[0] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
main.c:9286: chain[0] temp chip I2C addr=0x98
main.c:9269: chain[1] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
main.c:9286: chain[1] temp chip I2C addr=0x98
main.c:9269: chain[2] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1
main.c:9286: chain[2] temp chip I2C addr=0x98
main.c:13963: total_exist_chain_num = 3
main.c:14645: restart Miner chance num=0
main.c:14685: waiting for receive_func to exit!
main.c:14699: waiting for pic heart to exit!
main.c:13934: bmminer not found= 1031 root 2156 S grep bmminer

main.c:14743: bmminer not found, restart bmminer ...
driver-btm-c5.c:12248:bitmain_c5_init: This is the first time running after searching freq!
driver-btm-c5.c:12308:bitmain_c5_init: Detect 256MB control board of XILINX
driver-btm-c5.c:12327:bitmain_c5_init: Miner Type = S9+
driver-btm-c5.c:12334:bitmain_c5_init: Miner compile time: Thu Aug 1 16:39:38 CST 2019 type: Antminer S11
driver-btm-c5.c:12424:bitmain_c5_init: miner ID : 812c342a7910481c
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=1800
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=1800
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=1800
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:12581:bitmain_c5_init: Checking fans...
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4560
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3023:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3023:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3023:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3023:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3023:check_fan_beforeInit: waiting fans become stable...
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[0] speed=4440
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[1] speed=4440
driver-btm-c5.c:1767:jump_to_app_CheckAndRestorePIC_T9_18: chain[0] PIC jump to app
driver-btm-c5.c:1768:jump_to_app_CheckAndRestorePIC_T9_18: chain[0] PIC jump to app
driver-btm-c5.c:1773:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[0] PIC fw version=0xa4
driver-btm-c5.c:13034:bitmain_c5_init: Chain[0] read_freq_badcores : 0x7d 0xd9 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x52 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x52 0x56 0x56 0x56 0x56 0x52 0x56 0x56 0x52 0x56 0x52 0x56 0x56 0x56 0x52 0x52 0x56 0x56 0x2f 0x1a 0x00 0x00 0xc8 0xef 0xfe 0xfa 0xef 0xeb 0xbf 0xaf 0xbf 0xbf 0xbe 0xef 0xef 0xfb 0xee 0xbf 0xfe 0xfe 0xee 0xfb 0xeb 0xbf 0x5c 0x13 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
driver-btm-c5.c:13073:bitmain_c5_init: Chain[J1] has backup chain_voltage=1085
power.c:238:set_fixed_voltage: s9_84_fixed_voltage = 10.850000
driver-btm-c5.c:13084:bitmain_c5_init: S9+: use voltage limit rules on single board!
driver-btm-c5.c:13088:bitmain_c5_init: S9+ fix Chain[J1] test patten OK temp=60
driver-btm-c5.c:1767:jump_to_app_CheckAndRestorePIC_T9_18: chain[1] PIC jump to app
driver-btm-c5.c:1768:jump_to_app_CheckAndRestorePIC_T9_18: chain[1] PIC jump to app
driver-btm-c5.c:1773:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[1] PIC fw version=0xa4
driver-btm-c5.c:13034:bitmain_c5_init: Chain[1] read_freq_badcores : 0x7d 0xd9 0x4e 0x56 0x52 0x56 0x52 0x4e 0x56 0x52 0x4e 0x56 0x52 0x4e 0x4e 0x52 0x56 0x4e 0x56 0x52 0x56 0x52 0x4e 0x56 0x52 0x4e 0x4e 0x56 0x52 0x56 0x4e 0x52 0x4e 0x52 0x56 0x4e 0x56 0x52 0x56 0x4e 0x52 0x56 0x4e 0x52 0x56 0x4e 0x52 0x4e 0x56 0x52 0x56 0x4e 0x52 0x52 0x4e 0x56 0x56 0x4e 0x52 0x4e 0x52 0x56 0x56 0x52 0x4e 0x4e 0x52 0x56 0x52 0x4e 0x56 0x52 0x56 0x4e 0x4e 0x52 0x56 0x4e 0x56 0x52 0x56 0x4e 0x52 0x4e 0x56 0x52 0xb4 0x19 0x00 0x00 0xc8 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0x3f 0xff 0xcf 0xff 0xff 0xff 0xff 0xff 0x93 0x0b 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
driver-btm-c5.c:13073:bitmain_c5_init: Chain[J2] has backup chain_voltage=1085
power.c:238:set_fixed_voltage: s9_84_fixed_voltage = 10.850000
driver-btm-c5.c:13084:bitmain_c5_init: S9+: use voltage limit rules on single board!
driver-btm-c5.c:13088:bitmain_c5_init: S9+ fix Chain[J2] test patten OK temp=60
driver-btm-c5.c:1767:jump_to_app_CheckAndRestorePIC_T9_18: chain[2] PIC jump to app
driver-btm-c5.c:1768:jump_to_app_CheckAndRestorePIC_T9_18: chain[2] PIC jump to app
driver-btm-c5.c:1773:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[2] PIC fw version=0xa4
driver-btm-c5.c:13034:bitmain_c5_init: Chain[2] read_freq_badcores : 0x7d 0xd9 0x5a 0x56 0x52 0x52 0x5a 0x56 0x5a 0x56 0x52 0x52 0x56 0x5a 0x56 0x52 0x5a 0x5a 0x52 0x56 0x56 0x52 0x5a 0x52 0x5a 0x56 0x56 0x52 0x5a 0x5a 0x56 0x52 0x52 0x5a 0x56 0x52 0x56 0x5a 0x5a 0x52 0x56 0x56 0x52 0x5a 0x56 0x52 0x5a 0x52 0x5a 0x56 0x5a 0x52 0x56 0x56 0x52 0x5a 0x5a 0x52 0x56 0x56 0x5a 0x52 0x5a 0x52 0x56 0x56 0x5a 0x52 0x52 0x5a 0x56 0x52 0x56 0x5a 0x5a 0x56 0x52 0x56 0x5a 0x52 0x52 0x56 0x5a 0x5a 0x56 0x52 0x70 0x1a 0x00 0x00 0xc8 0xfd 0xdd 0x7f 0x5f 0xff 0xdd 0x5f 0x7f 0x7f 0x7d 0xdf 0xdf 0x7d 0xdf 0xdf 0xfd 0x7d 0x7f 0xfd 0xfd 0xf5 0xb6 0x13 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
driver-btm-c5.c:13073:bitmain_c5_init: Chain[J3] has backup chain_voltage=1085
power.c:238:set_fixed_voltage: s9_84_fixed_voltage = 10.850000
driver-btm-c5.c:13084:bitmain_c5_init: S9+: use voltage limit rules on single board!
driver-btm-c5.c:13088:bitmain_c5_init: S9+ fix Chain[J3] test patten OK temp=60
driver-btm-c5.c:12205:init_exist_chain_table: total_exist_chain_num = 3
power.c:148:power_check_protocal_type: power protocal f5, using package cmd
power.c:173:power_type_detect: start detect power type
power.c:181:power_type_detect: init gpio907
power.c:211:power_type_detect: power type is APW8 new type
power.c:587:get_min_voltage: board[1] voltage: 10.921582
power.c:587:get_min_voltage: board[2] voltage: 10.899023
power.c:587:get_min_voltage: board[0] voltage: 10.947363
power.c:593:get_min_voltage: min voltage: 10.899023
power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60
power.c:587:get_min_voltage: board[1] voltage: 10.879687
power.c:587:get_min_voltage: board[2] voltage: 10.857129
power.c:587:get_min_voltage: board[0] voltage: 10.908691
power.c:593:get_min_voltage: min voltage: 10.857129
power.c:370:voltage_tunning: last_iic_data = 60
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=44
power.c:587:get_min_voltage: board[1] voltage: 10.976367
power.c:587:get_min_voltage: board[2] voltage: 10.934473
power.c:587:get_min_voltage: board[0] voltage: 11.008594
power.c:593:get_min_voltage: min voltage: 10.934473
power.c:370:voltage_tunning: last_iic_data = 44
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=36
power.c:587:get_min_voltage: board[1] voltage: 11.031152
power.c:587:get_min_voltage: board[2] voltage: 10.982812
power.c:587:get_min_voltage: board[0] voltage: 11.040820
power.c:593:get_min_voltage: min voltage: 10.982812
power.c:370:voltage_tunning: last_iic_data = 36
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=32
power.c:587:get_min_voltage: board[1] voltage: 11.050488
power.c:587:get_min_voltage: board[2] voltage: 11.015039
power.c:587:get_min_voltage: board[0] voltage: 11.063379
power.c:593:get_min_voltage: min voltage: 11.015039
power.c:370:voltage_tunning: last_iic_data = 32
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=30
power.c:587:get_min_voltage: board[1] voltage: 11.063379
power.c:587:get_min_voltage: board[2] voltage: 11.034375
power.c:587:get_min_voltage: board[0] voltage: 11.073047
power.c:593:get_min_voltage: min voltage: 11.034375
power.c:370:voltage_tunning: last_iic_data = 30
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=30
power.c:587:get_min_voltage: board[1] voltage: 11.060156
power.c:587:get_min_voltage: board[2] voltage: 11.031152
power.c:587:get_min_voltage: board[0] voltage: 11.076270
power.c:593:get_min_voltage: min voltage: 11.031152
power.c:370:voltage_tunning: last_iic_data = 30
power.c:376:voltage_tunning: It's very close to target voltage, stop tunning
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=30
power.c:587:get_min_voltage: board[1] voltage: 11.047266
power.c:587:get_min_voltage: board[2] voltage: 11.027930
power.c:587:get_min_voltage: board[0] voltage: 11.076270
power.c:593:get_min_voltage: min voltage: 11.027930
power.c:370:voltage_tunning: last_iic_data = 30
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.900000, N=38
power.c:587:get_min_voltage: board[1] voltage: 11.018262
power.c:587:get_min_voltage: board[2] voltage: 10.966699
power.c:587:get_min_voltage: board[0] voltage: 11.021484
power.c:593:get_min_voltage: min voltage: 10.966699
power.c:370:voltage_tunning: last_iic_data = 38
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.900000, N=42
power.c:587:get_min_voltage: board[1] voltage: 10.976367
power.c:587:get_min_voltage: board[2] voltage: 10.966699
power.c:587:get_min_voltage: board[0] voltage: 11.011816
power.c:593:get_min_voltage: min voltage: 10.966699
power.c:370:voltage_tunning: last_iic_data = 42
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.900000, N=46
power.c:587:get_min_voltage: board[1] voltage: 10.963477
power.c:587:get_min_voltage: board[2] voltage: 10.937695
power.c:587:get_min_voltage: board[0] voltage: 10.986035
power.c:593:get_min_voltage: min voltage: 10.937695
power.c:370:voltage_tunning: last_iic_data = 46
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.900000, N=48
power.c:587:get_min_voltage: board[1] voltage: 10.950586
power.c:587:get_min_voltage: board[2] voltage: 10.915137
power.c:587:get_min_voltage: board[0] voltage: 10.989258
power.c:593:get_min_voltage: min voltage: 10.915137
power.c:370:voltage_tunning: last_iic_data = 48
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.900000, N=48
power.c:587:get_min_voltage: board[1] voltage: 10.944141
power.c:587:get_min_voltage: board[2] voltage: 10.928027
power.c:587:get_min_voltage: board[0] voltage: 10.979590
power.c:593:get_min_voltage: min voltage: 10.928027
power.c:370:voltage_tunning: last_iic_data = 48
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.900000, N=49
power.c:587:get_min_voltage: board[1] voltage: 10.944141
power.c:587:get_min_voltage: board[2] voltage: 10.921582
power.c:587:get_min_voltage: board[0] voltage: 10.979590
power.c:593:get_min_voltage: min voltage: 10.921582
power.c:370:voltage_tunning: last_iic_data = 49
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.900000, N=50
power.c:587:get_min_voltage: board[1] voltage: 10.940918
power.c:587:get_min_voltage: board[2] voltage: 10.918359
power.c:587:get_min_voltage: board[0] voltage: 10.969922
power.c:593:get_min_voltage: min voltage: 10.918359
power.c:370:voltage_tunning: last_iic_data = 50
power.c:376:voltage_tunning: It's very close to target voltage, stop tunning
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.900000, N=50
driver-btm-c5.c:2809:enable_pic_dac: echo 0 > /sys/class/gpio/gpio907/value
driver-btm-c5.c:2809:enable_pic_dac: echo 0 > /sys/class/gpio/gpio907/value
driver-btm-c5.c:2809:enable_pic_dac: echo 0 > /sys/class/gpio/gpio907/value
driver-btm-c5.c:13315:bitmain_c5_init: Chain[J1] orignal chain_voltage_pic=0 value=930
driver-btm-c5.c:13332:bitmain_c5_init: Chain[J1] will use backup chain_voltage_pic=1085 [0]
driver-btm-c5.c:13342:bitmain_c5_init: Chain[J1] get working chain_voltage_pic=0
driver-btm-c5.c:13315:bitmain_c5_init: Chain[J2] orignal chain_voltage_pic=0 value=930
driver-btm-c5.c:13332:bitmain_c5_init: Chain[J2] will use backup chain_voltage_pic=1085 [0]
driver-btm-c5.c:13342:bitmain_c5_init: Chain[J2] get working chain_voltage_pic=0
driver-btm-c5.c:13315:bitmain_c5_init: Chain[J3] orignal chain_voltage_pic=4 value=910
driver-btm-c5.c:13332:bitmain_c5_init: Chain[J3] will use backup chain_voltage_pic=1085 [0]
driver-btm-c5.c:13342:bitmain_c5_init: Chain[J3] get working chain_voltage_pic=0
driver-btm-c5.c:13433:bitmain_c5_init: Chain[J1] has 0 asic
driver-btm-c5.c:2832:disable_pic_dac: echo 1 > /sys/class/gpio/gpio907/value
driver-btm-c5.c:2809:enable_pic_dac: echo 0 > /sys/class/gpio/gpio907/value
driver-btm-c5.c:13461:bitmain_c5_init: retry Chain[J1] has 0 asic
driver-btm-c5.c:2832:disable_pic_dac: echo 1 > /sys/class/gpio/gpio907/value
driver-btm-c5.c:2809:enable_pic_dac: echo 0 > /sys/class/gpio/gpio907/value
driver-btm-c5.c:13461:bitmain_c5_init: retry Chain[J1] has 0 asic
driver-btm-c5.c:2832:disable_pic_dac: echo 1 > /sys/class/gpio/gpio907/value
driver-btm-c5.c:2809:enable_pic_dac: echo 0 > /sys/class/gpio/gpio907/value
driver-btm-c5.c:13461:bitmain_c5_init: retry Chain[J1] has 0 asic
driver-btm-c5.c:2832:disable_pic_dac: echo 1 > /sys/class/gpio/gpio907/value
driver-btm-c5.c:2809:enable_pic_dac: echo 0 > /sys/class/gpio/gpio907/value
driver-btm-c5.c:13461:bitmain_c5_init: retry Chain[J1] has 0 asic
driver-btm-c5.c:2832:disable_pic_dac: echo 1 > /sys/class/gpio/gpio907/value
driver-btm-c5.c:2809:enable_pic_dac: echo 0 > /sys/class/gpio/gpio907/value
driver-btm-c5.c:13461:bitmain_c5_init: retry Chain[J1] has 0 asic
driver-btm-c5.c:2832:disable_pic_dac: echo 1 > /sys/class/gpio/gpio907/value
driver-btm-c5.c:2809:enable_pic_dac: echo 0 > /sys/class/gpio/gpio907/value
driver-btm-c5.c:13461:bitmain_c5_init: retry Chain[J1] has 0 asic
driver-btm-c5.c:13433:bitmain_c5_init: Chain[J2] has 4 asic
driver-btm-c5.c:2832:disable_pic_dac: echo 1 > /sys/class/gpio/gpio907/value
driver-btm-c5.c:2809:enable_pic_dac: echo 0 > /sys/class/gpio/gpio907/value
driver-btm-c5.c:13461:bitmain_c5_init: retry Chain[J2] has 84 asic
driver-btm-c5.c:13433:bitmain_c5_init: Chain[J3] has 84 asic
driver-btm-c5.c:4545:set_frequency: Chain[J2] has no core num in PIC
driver-btm-c5.c:4545:set_frequency: Chain[J3] has no core num in PIC
driver-btm-c5.c:3769:get_total_rate_from_eeprom: totalrate = 13348
driver-btm-c5.c:4592:set_frequency: miner total rate=13348GH/s ideal_total_hash_rate = 13000GH/s
driver-btm-c5.c:4617:set_frequency: read PIC voltage=930 on chain[1]
driver-btm-c5.c:4619:set_frequency: Chain:1 chipnum=84
driver-btm-c5.c:4637:set_frequency: S9+ can not record Chain[J2] voltage added value
driver-btm-c5.c:4761:set_frequency: Chain:1 base freq=400
Asic[ 0]:675 Asic[ 1]:725 Asic[ 2]:700 Asic[ 3]:725 Asic[ 4]:700 Asic[ 5]:675 Asic[ 6]:725 Asic[ 7]:700
Asic[ 8]:675 Asic[ 9]:725 Asic[10]:700 Asic[11]:675 Asic[12]:675 Asic[13]:700 Asic[14]:725 Asic[15]:675
Asic[16]:725 Asic[17]:700 Asic[18]:725 Asic[19]:700 Asic[20]:675 Asic[21]:725 Asic[22]:700 Asic[23]:675
Asic[24]:675 Asic[25]:725 Asic[26]:700 Asic[27]:725 Asic[28]:675 Asic[29]:700 Asic[30]:675 Asic[31]:700
Asic[32]:725 Asic[33]:675 Asic[34]:725 Asic[35]:700 Asic[36]:725 Asic[37]:675 Asic[38]:700 Asic[39]:725
Asic[40]:675 Asic[41]:700 Asic[42]:725 Asic[43]:675 Asic[44]:700 Asic[45]:675 Asic[46]:725 Asic[47]:700
Asic[48]:725 Asic[49]:675 Asic[50]:700 Asic[51]:700 Asic[52]:675 Asic[53]:725 Asic[54]:725 Asic[55]:675
Asic[56]:700 Asic[57]:675 Asic[58]:700 Asic[59]:725 Asic[60]:725 Asic[61]:700 Asic[62]:675 Asic[63]:675
Asic[64]:700 Asic[65]:725 Asic[66]:700 Asic[67]:675 Asic[68]:725 Asic[69]:700 Asic[70]:725 Asic[71]:675
Asic[72]:675 Asic[73]:700 Asic[74]:725 Asic[75]:675 Asic[76]:725 Asic[77]:700 Asic[78]:725 Asic[79]:675
Asic[80]:700 Asic[81]:675 Asic[82]:725 Asic[83]:700
driver-btm-c5.c:4830:set_frequency: Chain:1 max freq=725
driver-btm-c5.c:4831:set_frequency: Chain:1 min freq=675

driver-btm-c5.c:4617:set_frequency: read PIC voltage=910 on chain[2]
driver-btm-c5.c:4619:set_frequency: Chain:2 chipnum=84
driver-btm-c5.c:4637:set_frequency: S9+ can not record Chain[J3] voltage added value
driver-btm-c5.c:4761:set_frequency: Chain:2 base freq=400
Asic[ 0]:750 Asic[ 1]:725 Asic[ 2]:700 Asic[ 3]:700 Asic[ 4]:750 Asic[ 5]:725 Asic[ 6]:750 Asic[ 7]:725
Asic[ 8]:700 Asic[ 9]:700 Asic[10]:725 Asic[11]:750 Asic[12]:725 Asic[13]:700 Asic[14]:750 Asic[15]:750
Asic[16]:700 Asic[17]:725 Asic[18]:725 Asic[19]:700 Asic[20]:750 Asic[21]:700 Asic[22]:750 Asic[23]:725
Asic[24]:725 Asic[25]:700 Asic[26]:750 Asic[27]:750 Asic[28]:725 Asic[29]:700 Asic[30]:700 Asic[31]:750
Asic[32]:725 Asic[33]:700 Asic[34]:725 Asic[35]:750 Asic[36]:750 Asic[37]:700 Asic[38]:725 Asic[39]:725
Asic[40]:700 Asic[41]:750 Asic[42]:725 Asic[43]:700 Asic[44]:750 Asic[45]:700 Asic[46]:750 Asic[47]:725
Asic[48]:750 Asic[49]:700 Asic[50]:725 Asic[51]:725 Asic[52]:700 Asic[53]:750 Asic[54]:750 Asic[55]:700
Asic[56]:725 Asic[57]:725 Asic[58]:750 Asic[59]:700 Asic[60]:750 Asic[61]:700 Asic[62]:725 Asic[63]:725
Asic[64]:750 Asic[65]:700 Asic[66]:700 Asic[67]:750 Asic[68]:725 Asic[69]:700 Asic[70]:725 Asic[71]:750
Asic[72]:750 Asic[73]:725 Asic[74]:700 Asic[75]:725 Asic[76]:750 Asic[77]:700 Asic[78]:700 Asic[79]:725
Asic[80]:750 Asic[81]:750 Asic[82]:725 Asic[83]:700
driver-btm-c5.c:4830:set_frequency: Chain:2 max freq=750
driver-btm-c5.c:4831:set_frequency: Chain:2 min freq=700

driver-btm-c5.c:4840:set_frequency: Miner fix freq ...
driver-btm-c5.c:4875:set_frequency: read PIC voltage=930 on chain[1]
driver-btm-c5.c:4876:set_frequency: Chain:1 chipnum=84
driver-btm-c5.c:4893:set_frequency: S9+ can not record Chain[J2] voltage added value
driver-btm-c5.c:5041:set_frequency: Chain:1 base freq=400
Asic[ 0]:675 Asic[ 1]:725 Asic[ 2]:700 Asic[ 3]:725 Asic[ 4]:700 Asic[ 5]:675 Asic[ 6]:725 Asic[ 7]:700
Asic[ 8]:675 Asic[ 9]:725 Asic[10]:700 Asic[11]:675 Asic[12]:675 Asic[13]:700 Asic[14]:725 Asic[15]:675
Asic[16]:725 Asic[17]:700 Asic[18]:725 Asic[19]:700 Asic[20]:675 Asic[21]:725 Asic[22]:700 Asic[23]:675
Asic[24]:675 Asic[25]:725 Asic[26]:700 Asic[27]:725 Asic[28]:675 Asic[29]:700 Asic[30]:675 Asic[31]:700
Asic[32]:725 Asic[33]:675 Asic[34]:725 Asic[35]:700 Asic[36]:725 Asic[37]:675 Asic[38]:700 Asic[39]:725
Asic[40]:675 Asic[41]:700 Asic[42]:725 Asic[43]:675 Asic[44]:700 Asic[45]:675 Asic[46]:725 Asic[47]:700
Asic[48]:725 Asic[49]:675 Asic[50]:700 Asic[51]:700 Asic[52]:675 Asic[53]:725 Asic[54]:725 Asic[55]:675
Asic[56]:700 Asic[57]:675 Asic[58]:700 Asic[59]:725 Asic[60]:725 Asic[61]:700 Asic[62]:675 Asic[63]:675
Asic[64]:700 Asic[65]:725 Asic[66]:700 Asic[67]:675 Asic[68]:725 Asic[69]:700 Asic[70]:725 Asic[71]:675
Asic[72]:675 Asic[73]:700 Asic[74]:725 Asic[75]:675 Asic[76]:725 Asic[77]:700 Asic[78]:725 Asic[79]:675
Asic[80]:700 Asic[81]:675 Asic[82]:725 Asic[83]:700
driver-btm-c5.c:5131:set_frequency: Chain:1 max freq=725
driver-btm-c5.c:5132:set_frequency: Chain:1 min freq=675

driver-btm-c5.c:4875:set_frequency: read PIC voltage=910 on chain[2]
driver-btm-c5.c:4876:set_frequency: Chain:2 chipnum=84
driver-btm-c5.c:4893:set_frequency: S9+ can not record Chain[J3] voltage added value
driver-btm-c5.c:5041:set_frequency: Chain:2 base freq=400
Asic[ 0]:750 Asic[ 1]:725 Asic[ 2]:700 Asic[ 3]:700 Asic[ 4]:750 Asic[ 5]:725 Asic[ 6]:750 Asic[ 7]:725
Asic[ 8]:700 Asic[ 9]:700 Asic[10]:725 Asic[11]:750 Asic[12]:725 Asic[13]:700 Asic[14]:750 Asic[15]:750
Asic[16]:700 Asic[17]:725 Asic[18]:725 Asic[19]:700 Asic[20]:750 Asic[21]:700 Asic[22]:750 Asic[23]:725
Asic[24]:725 Asic[25]:700 Asic[26]:750 Asic[27]:750 Asic[28]:725 Asic[29]:700 Asic[30]:700 Asic[31]:750
Asic[32]:725 Asic[33]:700 Asic[34]:725 Asic[35]:750 Asic[36]:750 Asic[37]:700 Asic[38]:725 Asic[39]:725
Asic[40]:700 Asic[41]:750 Asic[42]:725 Asic[43]:700 Asic[44]:750 Asic[45]:700 Asic[46]:750 Asic[47]:725
Asic[48]:750 Asic[49]:700 Asic[50]:725 Asic[51]:725 Asic[52]:700 Asic[53]:750 Asic[54]:750 Asic[55]:700
Asic[56]:725 Asic[57]:725 Asic[58]:750 Asic[59]:700 Asic[60]:750 Asic[61]:700 Asic[62]:725 Asic[63]:725
Asic[64]:750 Asic[65]:700 Asic[66]:700 Asic[67]:750 Asic[68]:725 Asic[69]:700 Asic[70]:725 Asic[71]:750
Asic[72]:750 Asic[73]:725 Asic[74]:700 Asic[75]:725 Asic[76]:750 Asic[77]:700 Asic[78]:700 Asic[79]:725
Asic[80]:750 Asic[81]:750 Asic[82]:725 Asic[83]:700
driver-btm-c5.c:5131:set_frequency: Chain:2 max freq=750
driver-btm-c5.c:5132:set_frequency: Chain:2 min freq=700

driver-btm-c5.c:5140:set_frequency: max freq = 750
driver-btm-c5.c:4183:ProcessFixFreq: totalRate = 13000, fixed_totalRate = 13000
driver-btm-c5.c:3307:set_PWM_according_to_temperature: set_PWM_according_to_temperature: fan set normal mode
driver-btm-c5.c:9624:init_uart_baud: set baud=1
driver-btm-c5.c:6614:calibration_sensor_offset: Chain[J2] PIC temp offset: -1,-1,-1,-1,-1,-1,-1,-1,0,0,0,0,0,0,0,0,0,0,
driver-btm-c5.c:6648:calibration_sensor_offset: chain[2] temp chip I2C addr=0x98
driver-btm-c5.c:6656:calibration_sensor_offset: chain[2] has no middle temp, use special fix mode.
driver-btm-c5.c:6786:calibration_sensor_offset: Warning: Chain[J2] has no temp offset in PIC! will fix it
driver-btm-c5.c:6910:calibration_sensor_offset: Chain[J2] use default temp chip[69]
driver-btm-c5.c:6340:do_calibration_sensor_offset: Chain[J2] try read temp chip[69] ID=55 (I2C addr=0x98)
driver-btm-c5.c:6405:do_calibration_sensor_offset: New offset Chain[2] chip[69] local:20 remote:22 offset:27
driver-btm-c5.c:6915:calibration_sensor_offset: Chain[J2] chip[69] get middle temp offset=27 typeID=55
driver-btm-c5.c:6910:calibration_sensor_offset: Chain[J2] use default temp chip[132]
driver-btm-c5.c:6340:do_calibration_sensor_offset: Chain[J2] try read temp chip[132] ID=55 (I2C addr=0x98)
driver-btm-c5.c:6405:do_calibration_sensor_offset: New offset Chain[2] chip[132] local:22 remote:24 offset:27
driver-btm-c5.c:6915:calibration_sensor_offset: Chain[J2] chip[132] get middle temp offset=27 typeID=55
driver-btm-c5.c:6614:calibration_sensor_offset: Chain[J3] PIC temp offset: -1,-1,-1,-1,-1,-1,-1,-1,0,0,0,0,0,0,0,0,0,0,
driver-btm-c5.c:6648:calibration_sensor_offset: chain[3] temp chip I2C addr=0x98
driver-btm-c5.c:6656:calibration_sensor_offset: chain[3] has no middle temp, use special fix mode.
driver-btm-c5.c:6786:calibration_sensor_offset: Warning: Chain[J3] has no temp offset in PIC! will fix it
driver-btm-c5.c:6910:calibration_sensor_offset: Chain[J3] use default temp chip[69]
driver-btm-c5.c:6340:do_calibration_sensor_offset: Chain[J3] try read temp chip[69] ID=55 (I2C addr=0x98)
driver-btm-c5.c:6405:do_calibration_sensor_offset: New offset Chain[3] chip[69] local:21 remote:23 offset:27
driver-btm-c5.c:6915:calibration_sensor_offset: Chain[J3] chip[69] get middle temp offset=27 typeID=55
driver-btm-c5.c:6910:calibration_sensor_offset: Chain[J3] use default temp chip[132]
driver-btm-c5.c:6340:do_calibration_sensor_offset: Chain[J3] try read temp chip[132] ID=55 (I2C addr=0x98)
driver-btm-c5.c:6405:do_calibration_sensor_offset: New offset Chain[3] chip[132] local:22 remote:24 offset:27
driver-btm-c5.c:6915:calibration_sensor_offset: Chain[J3] chip[132] get middle temp offset=27 typeID=55
driver-btm-c5.c:13763:bitmain_c5_init: open core three times
driver-btm-c5.c:13763:bitmain_c5_init: open core three times
driver-btm-c5.c:12113:set_working_voltage: setting to working voltage...
power.c:654:set_iic_power_to_working_voltage: setting to working voltage...
power.c:587:get_min_voltage: board[1] voltage: 10.921582
power.c:587:get_min_voltage: board[2] voltage: 10.892578
power.c:587:get_min_voltage: board[0] voltage: 10.950586
power.c:593:get_min_voltage: min voltage: 10.892578
power.c:370:voltage_tunning: last_iic_data = 50
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=34
power.c:587:get_min_voltage: board[1] voltage: 11.015039
power.c:587:get_min_voltage: board[2] voltage: 10.992480
power.c:587:get_min_voltage: board[0] voltage: 11.044043
power.c:593:get_min_voltage: min voltage: 10.992480
power.c:370:voltage_tunning: last_iic_data = 34
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=30
power.c:587:get_min_voltage: board[1] voltage: 11.040820
power.c:587:get_min_voltage: board[2] voltage: 11.015039
power.c:587:get_min_voltage: board[0] voltage: 11.063379
power.c:593:get_min_voltage: min voltage: 11.015039
power.c:370:voltage_tunning: last_iic_data = 30
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=28
power.c:587:get_min_voltage: board[1] voltage: 11.047266
power.c:587:get_min_voltage: board[2] voltage: 11.018262
power.c:587:get_min_voltage: board[0] voltage: 11.076270
power.c:593:get_min_voltage: min voltage: 11.018262
power.c:370:voltage_tunning: last_iic_data = 28
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=26
power.c:587:get_min_voltage: board[1] voltage: 11.056934
power.c:587:get_min_voltage: board[2] voltage: 11.040820
power.c:587:get_min_voltage: board[0] voltage: 11.089160
power.c:593:get_min_voltage: min voltage: 11.040820
power.c:370:voltage_tunning: last_iic_data = 26
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=26
power.c:587:get_min_voltage: board[1] voltage: 11.060156
power.c:587:get_min_voltage: board[2] voltage: 11.037598
power.c:587:get_min_voltage: board[0] voltage: 11.089160
power.c:593:get_min_voltage: min voltage: 11.037598
power.c:370:voltage_tunning: last_iic_data = 26
power.c:376:voltage_tunning: It's very close to target voltage, stop tunning
power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=26
driver-btm-c5.c:13966:bitmain_c5_init: start thread for read temp
setStartTimePoint total_tv_start_sys=285 total_tv_end_sys=286
driver-btm-c5.c:10338:check_system_work: restartNum = 2 , auto-reinit enabled...
do read_temp_func once...

get RT hashrate from Chain[1]: (asic index start from 1-84)

get RT hashrate from Chain[2]: (asic index start from 1-84)
Check Chain[J2] ASIC RT error: (asic index start from 1-84)
Check Chain[J3] ASIC RT error: (asic index start from 1-84)
Done check_asic_reg
read failed on Chain[1] Chip[18] middle Temp old value:15
Special fix Chain[1] Chip[18] middle Temp = 15
read failed on Chain[1] Chip[34] middle Temp old value:15
Special fix Chain[1] Chip[34] middle Temp = 15
Done read temp on Chain[1]
read failed on Chain[2] Chip[18] middle Temp old value:15
Special fix Chain[2] Chip[18] middle Temp = 15
read failed on Chain[2] Chip[34] middle Temp old value:15
Special fix Chain[2] Chip[34] middle Temp = 15
Done read temp on Chain[2]
Max pcb temp : 0
Read temp failed, set fixed full fan speed
FAN PWM: 100
read_temp_func Done!
CRC error counter=667