Antminer T17e hashboard has issue with temperature sensor

Follow
Tuan Le

I'm facing with an issue but I don't know how to debug it. Please help me for this

I also attached kernel log at below:

 

UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 036A4A97-F0B2-4D46-88C7-F7811B0DD899, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xb023
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2021-12-26 04:55:21 driver/thread.c:3055:create_restart_monitor_thread: create thread
2021-12-26 04:55:21 driver/driver-btm-api.c:294:init_freq_mode: This is scan-user version
2021-12-26 04:55:21 driver/driver-btm-api.c:2477:bitmain_soc_init: opt_multi_version = 1
2021-12-26 04:55:21 driver/driver-btm-api.c:2478:bitmain_soc_init: opt_bitmain_ab = 1
2021-12-26 04:55:21 driver/driver-btm-api.c:2479:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-12-26 04:55:21 driver/driver-btm-api.c:2480:bitmain_soc_init: Miner compile time: Mon Jun 14 19:45:42 MSK 2021 type: Antminer T17E v1.2.4
2021-12-26 04:55:21 driver/driver-btm-api.c:2482:bitmain_soc_init: commit version: daa20d7 2021-06-03 13:13:12, build by: root 2021-06-19 12:46:26
2021-12-26 04:55:21 driver/driver-btm-api.c:1904:show_sn: no SN got, please write SN to /nvdata/sn
2021-12-26 04:55:21 driver/fan.c:220:front_fan_power_on: Note: front fan is power on!
2021-12-26 04:55:21 driver/fan.c:226:rear_fan_power_on: Note: rear fan is power on!
2021-12-26 04:55:21 driver/driver-btm-api.c:1958:miner_device_init: Detect 256MB control board of XILINX
2021-12-26 04:55:21 driver/driver-btm-api.c:1932:init_fan_parameter: fan_eft : 0 fan_pwm : 0
2021-12-26 04:55:27 driver/driver-btm-api.c:1606:init_miner_version: miner ID : 8130d50c6920881c
2021-12-26 04:55:27 driver/driver-btm-api.c:1611:init_miner_version: FPGA Version = 0xB023
2021-12-26 04:55:32 driver/thread.c:3065:create_read_nonce_reg_thread: create thread
2021-12-26 04:55:32 driver/driver-btm-api.c:1685:bitmain_board_init: product_id[0] = 1
2021-12-26 04:55:32 driver/driver-btm-api.c:1685:bitmain_board_init: product_id[1] = 1
2021-12-26 04:55:32 driver/driver-btm-api.c:1685:bitmain_board_init: product_id[2] = 1
2021-12-26 04:55:32 driver/driver-btm-api.c:1706:bitmain_board_init: project:0
2021-12-26 04:55:32 driver/driver-btm-api.c:1049:dump_pcb_bom_version: Chain [0] PCB Version: 0x010a
2021-12-26 04:55:32 driver/driver-btm-api.c:1050:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2021-12-26 04:55:32 driver/driver-btm-api.c:1049:dump_pcb_bom_version: Chain [1] PCB Version: 0x010a
2021-12-26 04:55:32 driver/driver-btm-api.c:1050:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2021-12-26 04:55:32 driver/driver-btm-api.c:1049:dump_pcb_bom_version: Chain [2] PCB Version: 0x010a
2021-12-26 04:55:32 driver/driver-btm-api.c:1050:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2021-12-26 04:55:34 driver/driver-btm-api.c:1740:bitmain_board_init: Fan check passed.
2021-12-26 04:55:35 driver/board.c:31:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2021-12-26 04:55:39 driver/board.c:34:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0x88
2021-12-26 04:55:40 driver/board.c:31:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2021-12-26 04:55:44 driver/board.c:34:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0x88
2021-12-26 04:55:44 driver/board.c:31:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2021-12-26 04:55:49 driver/board.c:34:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0x88
2021-12-26 04:55:49 driver/thread.c:3060:create_pic_heart_beat_thread: create thread
2021-12-26 04:55:49 driver/power_api.c:228:power_init: power init ...
2021-12-26 04:55:50 driver/power_api.c:304:power_init: highest_voltage = 20.000000
2021-12-26 04:55:50 driver/power_api.c:305:power_init: working_voltage = 18.000000
2021-12-26 04:55:50 driver/power_api.c:306:power_init: higher_voltage = 18.500000
2021-12-26 04:55:50 driver/power_api.c:309:power_init: check_asic_voltage = 18.000000
2021-12-26 04:55:50 driver/driver-btm-api.c:1751:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-12-26 04:55:50 driver/power_api.c:214:power_off: init gpio907
2021-12-26 04:56:22 driver/power_api.c:500:set_to_check_asic_voltage: setting to voltage: 18.00 ...
2021-12-26 04:56:26 driver/uart.c:49:set_baud: set UART baud to 115200
2021-12-26 04:56:32 driver/driver-btm-api.c:1463:check_asic_number_with_power_on: Chain[0]: find 78 asic, times 0
2021-12-26 04:56:37 driver/driver-btm-api.c:1463:check_asic_number_with_power_on: Chain[1]: find 78 asic, times 0
2021-12-26 04:56:43 driver/driver-btm-api.c:1463:check_asic_number_with_power_on: Chain[2]: find 78 asic, times 0
2021-12-26 04:56:43 driver/power_api.c:819:set_to_highest_voltage_by_steps: Set to voltage 20.00, step by step.
2021-12-26 04:56:58 driver/driver-hash-chip.c:107:set_uart_relay: set uart relay to 0x330003
2021-12-26 04:56:58 driver/driver-hash-chip.c:299:set_clock_delay_control: core_data = 0x64
2021-12-26 04:56:59 driver/driver-hash-chip.c:126:set_ldo_ctrl: Set LDO to 0x2000203
2021-12-26 04:56:59 voltage[0] = 1850
2021-12-26 04:56:59 voltage[1] = 1850
2021-12-26 04:56:59 voltage[2] = 1850
2021-12-26 04:56:59 Highest voltage is 20.00
2021-12-26 04:56:59 driver/power_api.c:318:set_working_voltage: working_voltage = 18.500000
2021-12-26 04:56:59 driver/temperature.c:245:is_temp_sensor_type_correct: Wrong temp sensor (98) type, chain = 0, sensor = 12, type = 0x0, retry.
2021-12-26 04:57:00 driver/temperature.c:325:calibrate_temp_sensor_all_chains: chain 0 temp sensor NCT218, offset -8
2021-12-26 04:57:02 driver/temperature.c:325:calibrate_temp_sensor_all_chains: chain 1 temp sensor TMP451, offset -11
2021-12-26 04:57:03 driver/temperature.c:325:calibrate_temp_sensor_all_chains: chain 2 temp sensor TMP451, offset -11
2021-12-26 04:57:03 driver/uart.c:49:set_baud: set UART baud to 12000000
2021-12-26 04:57:05 driver/driver-btm-api.c:678:check_bringup_temp: Bring up temperature is 29
2021-12-26 04:57:05 driver/thread.c:3080:create_check_miner_status_thread: create thread
2021-12-26 04:57:05 driver/thread.c:3070:create_set_miner_status_thread: create thread
2021-12-26 04:57:05 driver/thread.c:3095:create_auto_tune_thread: create thread
2021-12-26 04:57:05 driver/thread.c:3100:create_read_real_voltage_thread: create thread
2021-12-26 04:57:05 driver/driver-btm-api.c:2660:bitmain_soc_init: get freq from eeprom
2021-12-26 04:58:02 driver/driver-btm-api.c:1015:set_timeout: freq = 605, percent = 90, hcn = 707788, timeout = 1168
2021-12-26 04:58:02 driver/driver-btm-api.c:2681:bitmain_soc_init: check fixup
2021-12-26 04:58:02 driver/power_api.c:813:set_to_working_voltage_by_steps: Set to voltage 18.50, step by step.
2021-12-26 04:58:07 driver/power_api.c:536:get_average_voltage: average_voltage = 18.492561
2021-12-26 04:58:07 driver/thread.c:3050:create_temperature_monitor_thread: create thread
2021-12-26 04:58:07 driver/thread.c:3075:create_check_system_status_thread: create thread
2021-12-26 04:58:07 driver/thread.c:3087:create_read_hash_rate_thread: create thread
2021-12-26 04:58:08 driver/driver-btm-api.c:2749:bitmain_soc_init: Init done!
2021-12-26 04:58:08 driver/driver-btm-api.c:210:set_miner_status: STATUS_INIT
2021-12-26 04:58:08 driver/driver-btm-api.c:210:set_miner_status: STATUS_OKAY
2021-12-26 04:58:13 driver/driver-btm-api.c:2993:dhash_chip_send_job: Version num 8
2021-12-26 04:59:08 LOST RATE ON CHAIN 1
2021-12-26 04:59:08 LOST RATE ON CHAIN 2
2021-12-26 04:59:08 LOST RATE ON CHAIN 3
2021-12-26 05:00:21 Got reinit signal
2021-12-26 05:00:21 driver/thread.c:3164:cancel_auto_tune_thread: cancel thread
2021-12-26 05:00:21 Restarting...
2021-12-26 05:00:21 Restart - 1
2021-12-26 05:00:29 Restart - 2
2021-12-26 05:00:37 Restart - 3
2021-12-26 05:00:44 Restart - 4
2021-12-26 05:00:52 Restart - 5
2021-12-26 05:01:00 Restart - 6

0

Comments

3 comments

Date Votes
  • Lisa

    This is  not official firmware,please flashing SD card and then  update to official firmware to check.

    0
    Comment actions Permalink
  • Tuan Le

    Hi Lisa

    This is latest official firmware for T17e, Is it right?

    0
    Comment actions Permalink
  • Tuan Le

    Hi Lisa

    I have updated latest firmware for T17e and this is kerner log at below. Please help to check. Thanks

     

    2021-12-28 17:16:38:driver-btm-api.c:2519:bitmain_soc_init: commit version: 37668c9 2021-01-08 18:20:11, build by: jenkins 2021-01-08 22:39:58
    2021-12-28 17:16:38:driver-btm-api.c:2520:bitmain_soc_init: opt_multi_version = 1
    2021-12-28 17:16:38:driver-btm-api.c:2521:bitmain_soc_init: opt_bitmain_ab = 1
    2021-12-28 17:16:38:driver-btm-api.c:2522:bitmain_soc_init: mid_auto_gen = 0
    2021-12-28 17:16:38:driver-btm-api.c:2523:bitmain_soc_init: work_mode = 0
    2021-12-28 17:16:38:driver-btm-api.c:2524:bitmain_soc_init: power_feedback_en = true
    2021-12-28 17:16:38:driver-btm-api.c:2067:show_sn: no SN got, please write SN to /config/sn
    2021-12-28 17:16:38:driver-btm-api.c:1384:miner_device_init: Detect 256MB control board of XILINX
    2021-12-28 17:16:38:driver-btm-api.c:1325:init_fan_parameter: fan_eft : 1 fan_pwm : 100
    2021-12-28 17:16:44:driver-btm-api.c:1309:init_miner_version: miner ID : 804225064e10481c
    2021-12-28 17:16:44:driver-btm-api.c:1315:init_miner_version: FPGA Version = 0xB023
    2021-12-28 17:16:49:auto_adapt.c:100:_get_board_info: chain[0] board bin: 1, chip bin: 3, chip ft: A4V41, chip version: AB
    2021-12-28 17:16:49:auto_adapt.c:100:_get_board_info: chain[1] board bin: 1, chip bin: 3, chip ft: A4V41, chip version: AB
    2021-12-28 17:16:49:auto_adapt.c:100:_get_board_info: chain[2] board bin: 1, chip bin: 4, chip ft: A4V4, chip version: AB
    2021-12-28 17:16:49:driver-btm-api.c:2172:get_calibration_voltage: calibration voltage is error data.
    2021-12-28 17:16:49 voltage[0] = 1850
    2021-12-28 17:16:49 voltage[1] = 1850
    2021-12-28 17:16:49 voltage[2] = 1780
    2021-12-28 17:16:49:driver-btm-api.c:486:check_chain_conf_same: Config are different, min = 1780, max = 1850, diff is too large.
    2021-12-28 17:16:49:auto_adapt.c:273:is_sweep_failed_before: open sweep tag failed
    2021-12-28 17:16:49:driver-btm-api.c:247:set_miner_status: ERROR_SOC_INIT
    2021-12-28 17:16:49:driver-btm-api.c:176:stop_mining: stop mining: soc init failed!
    2021-12-28 17:16:49:driver-btm-api.c:147:killall_hashboard: ****power off hashboard****
    2021-12-28 17:16:56:frequency.c:107:get_ideal_hash_rate_GH: ideal_hash_rate = 53752
    2021-12-28 17:16:57:thread.c:1543:create_shutdown_thread: create thread
    2021-12-28 17:16:57:thread.c:1221:is_status_ok: status (ERROR_SOC_INIT) is not okay.
    2021-12-28 17:16:57:thread.c:1304:shutdown_thread: stop mining.
    2021-12-28 17:16:57:driver-btm-api.c:176:stop_mining: stop mining: shutdown immediately
    2021-12-28 17:16:57:driver-btm-api.c:147:killall_hashboard: ****power off hashboard****

    0
    Comment actions Permalink

Please sign in to leave a comment.

Didn't find what you were looking for?

New post