S17+ Chain 0 only find 0 asic, will power off hash board 0

Comments

3 comments

  • Official comment

    Hello, it's recommended to clean the dust.

    https://support.bitmain.com/hc/en-us/articles/115004520173-How-To-Clean-and-Dust-The-Antminers

    Comment actions Permalink

    i clean and still does not work.

     

    2021-12-06 11:12:44 driver-btm-api.c:779:init_freq_mode: This is scan-user version
    2021-12-06 11:12:44 driver-btm-api.c:2451:bitmain_soc_init: opt_multi_version = 1
    2021-12-06 11:12:44 driver-btm-api.c:2452:bitmain_soc_init: opt_bitmain_ab = 1
    2021-12-06 11:12:44 driver-btm-api.c:2453:bitmain_soc_init: opt_bitmain_work_mode = 0
    2021-12-06 11:12:44 driver-btm-api.c:2454:bitmain_soc_init: Miner compile time: Tue Jun 2 10:31:07 CST 2020 type: Antminer S17+
    2021-12-06 11:12:44 driver-btm-api.c:2455:bitmain_soc_init: commit version: 1ca50a5 2020-06-01 18:51:22, build by: lol 2020-06-02 10:37:21
    2021-12-06 11:12:44 driver-btm-api.c:2083:show_sn: len:16, 8004642a18c0885c
    2021-12-06 11:12:44 driver-btm-api.c:2461:bitmain_soc_init: show sn return 1
    2021-12-06 11:12:44 driver-btm-api.c:2103:handle_sn_for_factory_mode: show sn return 1
    2021-12-06 11:12:44 driver-btm-api.c:2141:handle_sn_for_factory_mode: read sn success, 8004642a18c0885c
    2021-12-06 11:12:44 fan.c:284:front_fan_power_on: Note: front fan is power on!
    2021-12-06 11:12:44 fan.c:296:rear_fan_power_on: Note: rear fan is power on!
    2021-12-06 11:12:44 driver-btm-api.c:1314:miner_device_init: Detect 256MB control board of XILINX
    2021-12-06 11:12:44 driver-btm-api.c:1255:init_fan_parameter: fan_eft : 0 fan_pwm : 0
    2021-12-06 11:12:50 driver-btm-api.c:1239:init_miner_version: miner ID : 8004642a18c0885c
    2021-12-06 11:12:50 driver-btm-api.c:1245:init_miner_version: FPGA Version = 0xB023
    2021-12-06 11:12:54 driver-btm-api.c:837:get_product_id: product_id[0] = 0
    2021-12-06 11:12:54 driver-btm-api.c:837:get_product_id: product_id[1] = 0
    2021-12-06 11:12:54 driver-btm-api.c:2234:update_conf_by_power_feedback: Power feedback is disabled
    2021-12-06 11:12:54 driver-btm-api.c:2202:get_calibration_voltage: calibration voltage flag is error data.
    2021-12-06 11:12:54 driver-btm-api.c:2268:update_conf_by_power_feedback: Note: no calibration voltage, default diff = 0
    2021-12-06 11:12:54 frequency.c:1457:adjust_higer_max_vol_table: adjust_higer_max_vol_table, adjust_vol = 0
    2021-12-06 11:12:54 thread.c:1363:create_read_nonce_reg_thread: create thread
    2021-12-06 11:13:00 driver-btm-api.c:1239:init_miner_version: miner ID : 8004642a18c0885c
    2021-12-06 11:13:00 driver-btm-api.c:1245:init_miner_version: FPGA Version = 0xB023
    2021-12-06 11:13:04 driver-btm-api.c:837:get_product_id: product_id[0] = 0
    2021-12-06 11:13:04 driver-btm-api.c:837:get_product_id: product_id[1] = 0
    2021-12-06 11:13:04 driver-btm-api.c:792:_set_project_type: project:0
    2021-12-06 11:13:04 driver-btm-api.c:813:_set_project_type: Project type: Antminer S17+
    2021-12-06 11:13:04 driver-btm-api.c:824:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
    2021-12-06 11:13:04 driver-btm-api.c:825:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
    2021-12-06 11:13:04 driver-btm-api.c:824:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
    2021-12-06 11:13:04 driver-btm-api.c:825:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
    2021-12-06 11:13:06 driver-btm-api.c:2372:bitmain_board_init: Fan check passed.
    2021-12-06 11:13:07 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
    2021-12-06 11:13:09 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0x88
    2021-12-06 11:13:10 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
    2021-12-06 11:13:12 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0x88
    2021-12-06 11:13:12 thread.c:1358:create_pic_heart_beat_thread: create thread
    2021-12-06 11:13:12 power_api.c:213:power_init: Power init:
    2021-12-06 11:13:12 power_api.c:214:power_init: current_voltage_raw = 0
    2021-12-06 11:13:12 power_api.c:215:power_init: highest_voltage_raw = 2100
    2021-12-06 11:13:12 power_api.c:216:power_init: working_voltage_raw = 1950
    2021-12-06 11:13:12 power_api.c:217:power_init: higher_voltage_raw = 2040
    2021-12-06 11:13:12 power_api.c:218:power_init: check_asic_voltage_raw = 2100
    2021-12-06 11:13:12 driver-btm-api.c:2382:bitmain_board_init: Enter 30s sleep to make sure power release finish.
    2021-12-06 11:13:12 power_api.c:186:power_off: init gpio907
    2021-12-06 11:13:44 power_api.c:324:set_to_highest_voltage_by_steps: Set to voltage raw 2100, step by step.
    2021-12-06 11:14:10 power_api.c:85:check_voltage_multi: retry time: 0
    2021-12-06 11:14:11 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 21.249678
    2021-12-06 11:14:12 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 21.197944
    2021-12-06 11:14:12 power_api.c:53:_get_avg_voltage: average_voltage = 21.223811
    2021-12-06 11:14:12 power_api.c:71:check_voltage: target_vol = 21.00, actural_vol = 21.22, check voltage passed.
    2021-12-06 11:14:12 uart.c:72:set_baud: set fpga_baud to 115200
    2021-12-06 11:14:23 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[0]: find 65 asic, times 0
    2021-12-06 11:14:34 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 0
    2021-12-06 11:14:44 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 1
    2021-12-06 11:14:55 driver-btm-api.c:1134:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 2
    2021-12-06 11:14:55 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw = 2100
    chain 1, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
    2021-12-06 11:15:03 driver-btm-api.c:1157:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 3
    2021-12-06 11:15:03 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw = 2050
    2021-12-06 11:15:03 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2050, step by step.
    2021-12-06 11:15:07 power_api.c:85:check_voltage_multi: retry time: 0
    2021-12-06 11:15:08 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 20.685091
    2021-12-06 11:15:09 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.634145
    2021-12-06 11:15:09 power_api.c:53:_get_avg_voltage: average_voltage = 20.659618
    2021-12-06 11:15:09 power_api.c:71:check_voltage: target_vol = 20.50, actural_vol = 20.66, check voltage passed.
    chain 1, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
    2021-12-06 11:15:18 driver-btm-api.c:1157:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 4
    2021-12-06 11:15:18 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw = 2000
    2021-12-06 11:15:18 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2000, step by step.
    2021-12-06 11:15:21 power_api.c:85:check_voltage_multi: retry time: 0
    2021-12-06 11:15:22 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 20.196659
    2021-12-06 11:15:23 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.121950
    2021-12-06 11:15:23 power_api.c:53:_get_avg_voltage: average_voltage = 20.159305
    2021-12-06 11:15:23 power_api.c:71:check_voltage: target_vol = 20.00, actural_vol = 20.16, check voltage passed.
    chain 1, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
    2021-12-06 11:15:32 driver-btm-api.c:1157:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 5
    2021-12-06 11:15:32 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw = 2100
    2021-12-06 11:15:32 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2100, step by step.
    2021-12-06 11:15:37 power_api.c:85:check_voltage_multi: retry time: 0
    2021-12-06 11:15:39 power_api.c:40:_get_avg_voltage: chain = 0, voltage = 21.170731
    2021-12-06 11:15:40 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 21.121950
    2021-12-06 11:15:40 power_api.c:53:_get_avg_voltage: average_voltage = 21.146341
    2021-12-06 11:15:40 power_api.c:71:check_voltage: target_vol = 21.00, actural_vol = 21.15, check voltage passed.
    2021-12-06 11:15:40 driver-btm-api.c:1193:check_asic_number: Chain 1 only find 0 asic, will power off hash board 1
    2021-12-06 11:15:41 driver-btm-api.c:1195:check_asic_number: Chain 1 voltage: an0 = 2.787097, an2 2.793548, an6 2.512903.
    2021-12-06 11:15:45 driver-hash-chip.c:266:set_uart_relay: set uart relay to 0x330003
    2021-12-06 11:15:45 driver-btm-api.c:435:set_order_clock: chain[0]: set order clock, stragegy 3
    2021-12-06 11:15:45 driver-hash-chip.c:502:set_clock_delay_control: core_data = 0x34
    2021-12-06 11:15:45 driver-btm-api.c:1892:check_clock_counter: freq 50 clock_counter_limit 6
    2021-12-06 11:15:45 register.c:979:register_process_asic_response: Get another asic response: chain = 0, asic = 30
    2021-12-06 11:15:45 register.c:979:register_process_asic_response: Get another asic response: chain = 0, asic = 30
    2021-12-06 11:15:45 register.c:979:register_process_asic_response: Get another asic response: chain = 0, asic = 30
    2021-12-06 11:15:45 register.c:979:register_process_asic_response: Get another asic response: chain = 0, asic = 30
    2021-12-06 11:15:45 register.c:979:register_process_asic_response: Get another asic response: chain = 0, asic = 30
    2021-12-06 11:15:45 register.c:979:register_process_asic_response: Get another asic response: chain = 0, asic = 30
    2021-12-06 11:15:45 register.c:979:register_process_asic_response: Get another asic response: chain = 0, asic = 30
    2021-12-06 11:15:45 register.c:979:register_process_asic_response: Get another asic response: chain = 0, asic = 30
    2021-12-06 11:15:45 register.c:979:register_process_asic_response: Get another asic response: chain = 0, asic = 30
    2021-12-06 11:15:45 register.c:979:register_process_asic_response: Get another asic response: chain = 0, asic = 30
    2021-12-06 11:15:45 register.c:979:register_process_asic_response: Get another asic response: chain = 0, asic = 30
    2021-12-06 11:15:45 voltage[0] = 1960
    2021-12-06 11:15:45 power_api.c:226:set_working_voltage_raw: working_voltage_raw = 1960
    2021-12-06 11:15:46 temperature.c:340:calibrate_temp_sensor_one_chain: chain 0 temp sensor NCT218
    2021-12-06 11:15:46 uart.c:72:set_baud: set fpga_baud to 12000000
    2021-12-06 11:15:47 driver-btm-api.c:293:check_bringup_temp: Bring up temperature is 22
    2021-12-06 11:15:47 thread.c:1378:create_check_miner_status_thread: create thread
    2021-12-06 11:15:47 thread.c:1368:create_show_miner_status_thread: create thread
    2021-12-06 11:15:47 thread.c:1348:create_temperature_monitor_thread: create thread
    2021-12-06 11:15:47 frequency.c:514:check_bringup_temp_dec_freq: dec freq = 0 when bringup temp = 22 dec_freq_index=0
    2021-12-06 11:15:47 freq_tuning.c:183:freq_tuning_get_max_freq: Max freq of tuning is 650
    2021-12-06 11:15:47 driver-btm-api.c:1765:send_null_work: [DEBUG] Send null work.

    0
    Comment actions Permalink

    Hello, this kernel log isn't completed,  please send a completed kernel log to support-cs@bitmain.com

    -1
    Comment actions Permalink

Please sign in to leave a comment.