S19jPRO won't fully boot after firmware update

Answered

Comments

30 comments

  • Official comment

    Dear

    It showed ERROR_SOC_INIT: basic init failed! Could you try the below instructions ?

    1 Plug and unplug the cable, 2 flashing the sd card to recover to the control board, 3 and configure whether there is a mix board

    Comment actions Permalink

    Dear Jessica,

    I tried multiple times to flash the firmware using SD card, but result is still the same. Can you please confirm if this is the right firmware for S19j Pro 96T (SD card slot is on the front panel)? https://file12.bitmain.com/shop-product-s3/firmware/fc85582f-6010-4f77-9905-e822eac9d404/2021/08/26/10/Antminer-S19j-Pro-Release-sd2nand-zynq7007-20210605.zip

    Because according logs I suspect this is not firmware for "Pro" version of S19j.

    first line in log:

    1970-01-01 00:00:09 Miner compile time: Sat Jun 5 23:30:08 CST 2021 type: Antminer S19j

     

    Upgrading firmware using web interface does nothing. If I select .bin file, page is only reload in second and no message appears. I used this file: https://file12.bitmain.com/shop-product-s3/firmware/83fcb34e-43ab-4ceb-a559-b67a59f9bd63/2021/07/08/18/Antminer-S19j-Pro-release-202106281212.bin

    Is anyhow possible to try flash May version, which was there before I upgraded to June version?

    1
    Comment actions Permalink

    Dear

    Could you send us your email address,we will send you s19jpro sd card file.

    1
    Comment actions Permalink

    Dear Jessica, this is my email address: mining@dbs.sk

    thanks

    1
    Comment actions Permalink

    Hello,

    have you sent it already, please? Because I still not receive your email.

    1
    Comment actions Permalink

    I encountered this problem too. I also need the firmware file. Email : suplanlaman@gmail.com

    1
    Comment actions Permalink

    Dear

    We sent it please double check in your email.

    2
    Comment actions Permalink

    I received the files and successfully updated the firmware. Thank you very much for your support Nick

    1
    Comment actions Permalink

    hi jessica,

    i have the same problem with the s19j pro 104th.i flashing the control board and now nothing appear on the dashboard , red FAULT LED is steady ON and green NORMAL LED is OFF.please help me jessica ,my email cedcttc@hotmail.com

    free_area_init_node: node 0, pgdat c0b3c040, node_mem_map cde10000
      Normal zone: 480 pages used for memmap
      Normal zone: 0 pages reserved
      Normal zone: 61440 pages, LIFO batch:15
    percpu: Embedded 12 pages/cpu @cddf0000 s19916 r8192 d21044 u49152
    pcpu-alloc: s19916 r8192 d21044 u49152 alloc=12*4096
    pcpu-alloc: [0] 0 [0] 1 
    Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
    Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
    PID hash table entries: 1024 (order: 0, 4096 bytes)
    Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
    Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
    Memory: 209668K/245760K available (6317K kernel code, 243K rwdata, 1932K rodata, 1024K init, 232K bss, 19708K reserved, 16384K cma-reserved, 0K highmem)
    Virtual kernel memory layout:
        vector  : 0xffff0000 - 0xffff1000   (   4 kB)
        fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
        vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
        lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
        pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
        modules : 0xbf000000 - 0xbfe00000   (  14 MB)
          .text : 0xc0008000 - 0xc090e410   (9242 kB)
          .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
          .data : 0xc0b00000 - 0xc0b3cda0   ( 244 kB)
           .bss : 0xc0b3cda0 - 0xc0b77024   ( 233 kB)
    Preemptible hierarchical RCU implementation.
    	Build-time adjustment of leaf fanout to 32.
    	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
    RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
    NR_IRQS:16 nr_irqs:16 16
    efuse mapped to cf800000
    ps7-slcr mapped to cf802000
    L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
    L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
    L2C-310 erratum 769419 enabled
    L2C-310 enabling early BRESP for Cortex-A9
    L2C-310 full line of zeros enabled for Cortex-A9
    L2C-310 ID prefetch enabled, offset 1 lines
    L2C-310 dynamic clock gating enabled, standby mode enabled
    L2C-310 cache controller enabled, 8 ways, 512 kB
    L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
    zynq_clock_init: clkc starts at cf802100
    Zynq clock init
    sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
    clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
    Switching to timer-based delay loop, resolution 3ns
    clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
    ps7-ttc #0 at cf80a000, irq=18
    Console: colour dummy device 80x30
    Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
    pid_max: default: 32768 minimum: 301
    Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
    Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
    CPU: Testing write buffer coherency: ok
    CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
    Setting up static identity map for 0x100000 - 0x100058
    CPU1: failed to boot: -1
    Brought up 1 CPUs
    SMP: Total of 1 processors activated (666.66 BogoMIPS).
    CPU: All CPU(s) started in SVC mode.
    devtmpfs: initialized
    VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
    clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
    pinctrl core: initialized pinctrl subsystem
    NET: Registered protocol family 16
    DMA: preallocated 256 KiB pool for atomic coherent allocations
    cpuidle: using governor menu
    hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
    hw-breakpoint: maximum watchpoint size is 4 bytes.
    zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
    vgaarb: loaded
    SCSI subsystem initialized
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    media: Linux media interface: v0.10
    Linux video capture interface: v2.00
    pps_core: LinuxPPS API ver. 1 registered
    pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    PTP clock support registered
    EDAC MC: Ver: 3.0.0
    Advanced Linux Sound Architecture Driver Initialized.
    clocksource: Switched to clocksource arm_global_timer
    NET: Registered protocol family 2
    TCP established hash table entries: 2048 (order: 1, 8192 bytes)
    TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
    TCP: Hash tables configured (established 2048 bind 2048)
    UDP hash table entries: 256 (order: 1, 8192 bytes)
    UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
    NET: Registered protocol family 1
    RPC: Registered named UNIX socket transport module.
    RPC: Registered udp transport module.
    RPC: Registered tcp transport module.
    RPC: Registered tcp NFSv4.1 backchannel transport module.
    PCI: CLS 0 bytes, default 64
    Trying to unpack rootfs image as initramfs...
    rootfs image is not initramfs (no cpio magic); looks like an initrd
    Freeing initrd memory: 6636K (cd47e000 - cdaf9000)
    hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
    futex hash table entries: 512 (order: 3, 32768 bytes)
    workingset: timestamp_bits=28 max_order=16 bucket_order=0
    jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
    io scheduler noop registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
    dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
    e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 159, base_baud = 6249999) is a xuartps
    console [ttyPS0] enabled
    xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
    [drm] Initialized drm 1.1.0 20060810
    brd: module loaded
    loop: module loaded
    CAN device driver interface
    gpiod_set_value: invalid GPIO
    libphy: MACB_mii_bus: probed
    macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
    Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
    e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
    e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    ehci-pci: EHCI PCI platform driver
    usbcore: registered new interface driver usb-storage
    mousedev: PS/2 mouse device common for all mice
    i2c /dev entries driver
    cdns-i2c e0005000.ps7_i2c: 100 kHz mmio e0005000 irq 154
    Xilinx Zynq CpuIdle Driver started
    sdhci: Secure Digital Host Controller Interface driver
    sdhci: Copyright(c) Pierre Ossman
    sdhci-pltfm: SDHCI platform and OF driver helper
    mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
    ledtrig-cpu: registered to indicate activity on CPUs
    usbcore: registered new interface driver usbhid
    usbhid: USB HID core driver
    nand: disable subpage write
    nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
    nand: Micron MT29F2G08ABAEAWP
    nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
    nand: NAND_ECC_HW
    nand: NAND_ECC_HW_SYNDROME
    mtd->writesize = 2048
    ecc->strength = 1
    ecc->size = 2048
    mtd->writesize = 2048
    chip->ecc_strength_ds = 4
    chip->ecc_step_ds = 512
    nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
    Bad block table found at page 131008, version 0x01
    Bad block table found at page 130944, version 0x01
    nand_read_bbt: bad block at 0x000002420000
    nand_read_bbt: bad block at 0x000002440000
    nand_read_bbt: bad block at 0x000002460000
    8 ofpart partitions found on MTD device pl35x-nand
    Creating 8 MTD partitions on "pl35x-nand":
    0x000000000000-0x000002800000 : "BOOT.bin-dts-marker-kernel"
    0x000002800000-0x000004800000 : "ramfs"
    0x000004800000-0x000005000000 : "configs"
    0x000005000000-0x000005200000 : "sig"
    0x000005200000-0x000006000000 : "reserve1"
    0x000006000000-0x000007000000 : "upgrade-ramfs"
    0x000007000000-0x00000a800000 : "upgrade-file"
    0x00000a800000-0x000010000000 : "reserve2"
    nf_conntrack version 0.5.0 (3635 buckets, 14540 max)
    ip_tables: (C) 2000-2006 Netfilter Core Team
    NET: Registered protocol family 10
    ip6_tables: (C) 2000-2006 Netfilter Core Team
    sit: IPv6 over IPv4 tunneling driver
    NET: Registered protocol family 17
    can: controller area network core (rev 20120528 abi 9)
    NET: Registered protocol family 29
    can: raw protocol (rev 20120528)
    can: broadcast manager protocol (rev 20120528 t)
    can: netlink gateway (rev 20130117) max_hops=1
    zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
    zynq_pm_late_init: Unable to map DDRC IO memory.
    Registering SWP/SWPB emulation handler
    hctosys: unable to open rtc device (rtc0)
    ALSA device list:
      No soundcards found.
    RAMDISK: gzip image found at block 0
    EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
    EXT4-fs warning (device ram0): ext4_update_dynamic_rev:746: updating to rev 1 because of new feature flag, running e2fsck is recommended
    EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
    VFS: Mounted root (ext4 filesystem) on device 1:0.
    devtmpfs: mounted
    Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
    EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr,errors=remount-ro
    devpts: called with bogus options
    ubi0: attaching mtd2
    ubi0: scanning is finished
    ubi0: attached mtd2 (name "configs", size 8 MiB)
    ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
    ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
    ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
    ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
    ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
    ubi0: max/mean erase counter: 14/5, WL threshold: 4096, image sequence number: 1592366032
    ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 4
    ubi0: background thread "ubi_bgt0d" started, PID 729
    UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 733
    UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "config_data"
    UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
    UBIFS (ubi0:0): FS size: 5840896 bytes (5 MiB, 46 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
    UBIFS (ubi0:0): reserved for root: 275879 bytes (269 KiB)
    UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 46301BA8-09E7-4F0B-A631-FEFD2CAA72F6, small LPT model
    ubi2: attaching mtd4
    ubi2: scanning is finished
    ubi2: attached mtd4 (name "reserve1", size 14 MiB)
    ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
    ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
    ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096
    ubi2: good PEBs: 112, bad PEBs: 0, corrupted PEBs: 0
    ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128
    ubi2: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 2794267924
    ubi2: available PEBs: 0, total reserved PEBs: 112, PEBs reserved for bad PEB handling: 4
    ubi2: background thread "ubi_bgt2d" started, PID 740
    UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 744
    UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "misc"
    UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
    UBIFS (ubi2:0): FS size: 11935744 bytes (11 MiB, 94 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
    UBIFS (ubi2:0): reserved for root: 563754 bytes (550 KiB)
    UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID F99AEFB2-755E-45F0-9E43-952FD002FABD, small LPT model
    IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    random: avahi-daemon urandom read with 2 bits of entropy available
    macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
    macb e000b000.ethernet eth0: link up (100/Full)
    IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    In axi fpga driver!
    request_mem_region OK!
    AXI fpga dev virtual address is 0xcfbc8000
    *base_vir_addr = 0xb031
    In fpga mem driver!
    request_mem_region OK!
    fpga mem virtual address is 0xd2000000
    random: nonblocking pool is initialized
    
    
    ===========================================Miner log===========================================
    1970-01-01 00:00:09 Miner compile time: Sat Jun  5 23:30:08 CST 2021 type: Antminer S19j
    1970-01-01 00:00:10 This is fix-freq version
    1970-01-01 00:00:10 Miner compile time: Sat Jun  5 23:30:08 CST 2021 type: Antminer S19j
    1970-01-01 00:00:10 commit version: e02de5b 2021-06-05 22:56:34, build by: jenkins 2021-06-05 23:30:07
    1970-01-01 00:00:10 opt_multi_version     = 1
    1970-01-01 00:00:10 opt_bitmain_ab        = 1
    1970-01-01 00:00:10 mid_auto_gen          = 0
    1970-01-01 00:00:10 opt_bitmain_work_mode = 0
    1970-01-01 00:00:10 mmap fpga_mem_addr_hal = 0xb5900000
    1970-01-01 00:00:10 HASH_ON_PLUG V9 = 0x7
    1970-01-01 00:00:10 Note: front fan is power on!
    1970-01-01 00:00:10 Note: rear fan is power on!
    1970-01-01 00:00:10 start the http log.
    1970-01-01 00:00:10 httpListenThread start ret=0
    1970-01-01 00:00:10 start listen on 6060 ...
    1970-01-01 00:00:10 load machine BHB42701 conf
    1970-01-01 00:00:10 machine : BHB42701 
    1970-01-01 00:00:10 chain_num 4, chain_domain_num 36, chain_asic_num 108, domain_asic_num 3
    1970-01-01 00:00:16 miner ID : 8064a5282b10481c
    1970-01-01 00:00:16 FPGA Version = 0xB031
    1970-01-01 00:00:16 HASH_ON_PLUG V9 = 0x7
    1970-01-01 00:00:16 ==========================capability start==========================
    1970-01-01 00:00:16 board num = 3
    1970-01-01 00:00:16 board id = 0, chain num = 1
    1970-01-01 00:00:16 	chain id = 0
    1970-01-01 00:00:16 board id = 1, chain num = 1
    1970-01-01 00:00:16 	chain id = 1
    1970-01-01 00:00:16 board id = 2, chain num = 1
    1970-01-01 00:00:16 	chain id = 2
    1970-01-01 00:00:16 ==========================capability end============================
    1970-01-01 00:00:16 chain num = 3
    2021-10-04 06:12:15 load chain 0 eeprom data
    2021-10-04 06:12:15 FW type BHB42701, eeprom[0] shows BHB42601
    2021-10-04 06:12:16 load chain 1 eeprom data
    2021-10-04 06:12:16 FW type BHB42701, eeprom[1] shows BHB42601
    2021-10-04 06:12:18 load chain 2 eeprom data
    2021-10-04 06:12:18 FW type BHB42701, eeprom[2] shows BHB42601
    2021-10-04 06:12:18 Sweep error string = J255:4.
    2021-10-04 06:12:18 Fixture data load failed, exit.
    2021-10-04 06:12:18 ERROR_SOC_INIT: basic init failed!
    2021-10-04 06:12:18 stop_mining: basic init failed!
    2021-10-04 06:12:18 ****power off hashboard****
    2021-10-04 06:12:19 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0xff, read_back_data[1] = 0xff
    2021-10-04 06:12:20 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0xff, read_back_data[1] = 0xff
    2021-10-04 06:12:20 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0xff, read_back_data[1] = 0xff
    1
    Comment actions Permalink

    BEWARE!

    DO NOT INSTALL the S19j Pro SD card recovery package.  It has BRICKED our miner!

    • Antminer-S19j-Pro-Release-sd2nand-zynq7007-20210605.zip (file size 26.87MB)
    • S19j Pro SD firmware for 7007 control board only (published 2021-08-26)

    This package is identical to the S19j package.  We have compared and match both packages' "update.bmu" file checksums.  Your miner will not be able to detect hash boards, reset to factory default firmware, or update to the Antminer-S19j-Pro-release-202106281212.bin firmware.  Effectively rendering your equipment useless.

    Bitmain support, please send the correct S19j Pro 100T (7007) recovery to niftyframes@protonmail.com

    1
    Comment actions Permalink

    I had the same issue, it sounds like!  Hopefully there is hope for me.  Please help if you are able.  I have spent many hours trying website reset, physical power off with switch, reloading firmware, and searching the Internet.

    I have S19j Pro 96 TH unit, with 7007 control board (integrated).  I installed the following using 2GB micro SD card formatted FAT32:

    https://service.bitmain.com/support/download?product=Flashing%20SD%20card%20with%20image
    Antminer-S19j-Pro-Release-sd2nand-zynq7007-20210605.zip
    S19j Pro SD firmware for 7007 control board only
    26.87MB, 2021-08-26

    The web interface now says "Firmware Version Sat Jun 5 23:30:08 CST 2021".

    After restart, the current log says:

    ===========================================Miner log===========================================
    1970-01-01 00:00:09 Miner compile time: Sat Jun  5 23:30:08 CST 2021 type: Antminer S19j
    1970-01-01 00:00:10 This is fix-freq version
    1970-01-01 00:00:10 Miner compile time: Sat Jun  5 23:30:08 CST 2021 type: Antminer S19j
    1970-01-01 00:00:10 commit version: e02de5b 2021-06-05 22:56:34, build by: jenkins 2021-06-05 23:30:07
    1970-01-01 00:00:10 opt_multi_version     = 1
    1970-01-01 00:00:10 opt_bitmain_ab        = 1
    1970-01-01 00:00:10 mid_auto_gen          = 0
    1970-01-01 00:00:10 opt_bitmain_work_mode = 0
    1970-01-01 00:00:10 mmap fpga_mem_addr_hal = 0xb5800000
    1970-01-01 00:00:10 HASH_ON_PLUG V9 = 0x7
    1970-01-01 00:00:10 Note: front fan is power on!
    1970-01-01 00:00:10 Note: rear fan is power on!
    1970-01-01 00:00:10 start the http log.
    1970-01-01 00:00:10 httpListenThread start ret=0
    1970-01-01 00:00:10 start listen on 6060 ...
    1970-01-01 00:00:10 load machine BHB42701 conf
    1970-01-01 00:00:10 machine : BHB42701 
    1970-01-01 00:00:10 chain_num 4, chain_domain_num 36, chain_asic_num 108, domain_asic_num 3
    2021-10-07 05:55:49 miner ID : 8034f54675104814
    2021-10-07 05:55:49 FPGA Version = 0xB031
    2021-10-07 05:55:49 HASH_ON_PLUG V9 = 0x7
    2021-10-07 05:55:49 ==========================capability start==========================
    2021-10-07 05:55:49 board num = 3
    2021-10-07 05:55:49 board id = 0, chain num = 1
    2021-10-07 05:55:49 	chain id = 0
    2021-10-07 05:55:49 board id = 1, chain num = 1
    2021-10-07 05:55:49 	chain id = 1
    2021-10-07 05:55:49 board id = 2, chain num = 1
    2021-10-07 05:55:49 	chain id = 2
    2021-10-07 05:55:49 ==========================capability end============================
    2021-10-07 05:55:49 chain num = 3
    2021-10-07 05:55:51 load chain 0 eeprom data
    2021-10-07 05:55:51 FW type BHB42701, eeprom[0] shows BHB42601
    2021-10-07 05:55:53 load chain 1 eeprom data
    2021-10-07 05:55:53 FW type BHB42701, eeprom[1] shows BHB42601
    2021-10-07 05:55:55 load chain 2 eeprom data
    2021-10-07 05:55:55 FW type BHB42701, eeprom[2] shows BHB42601
    2021-10-07 05:55:55 Sweep error string = J255:4.
    2021-10-07 05:55:55 Fixture data load failed, exit.
    2021-10-07 05:55:55 ERROR_SOC_INIT: basic init failed!
    2021-10-07 05:55:55 stop_mining: basic init failed!
    2021-10-07 05:55:55 ****power off hashboard****
    2021-10-07 05:55:56 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0xff, read_back_data[1] = 0xff
    2021-10-07 05:55:56 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0xff, read_back_data[1] = 0xff
    2021-10-07 05:55:57 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0xff, read_back_data[1] = 0xff

    I also tried loading the firmware using a 16GB micro SD card, in case my 2GB card was defective, but loading with the 16GB card had the same result.

    Please sent correct firmware and recovery instructions to me at <55368047421+support@pm.me>.  Thank you!

    0
    Comment actions Permalink

    I encountered this problem too. I also need the firmware file. Email : belkin_87@inbox.ru

    0
    Comment actions Permalink

    Sent to  belkin_87@inbox.ru

    0
    Comment actions Permalink

    Linda thank you for replying to Alexandr.  Would you please send to me too?  I did not receive the file yet.  Email: <55368047421+support@pm.me>  Thank you!

    0
    Comment actions Permalink

    Still didn't receive it yet. Could you please dublicate email to alexandrbelkin87@gmail.com?

    0
    Comment actions Permalink

    Hello, sent to  alexandrbelkin87@gmail.com

    0
    Comment actions Permalink

    Hello, sent to 55368047421+support@pm.me

    0
    Comment actions Permalink

    Hello, sent to belkin_87@inbox.ru again.

    0
    Comment actions Permalink

    Thank you for your support. But I still didn't get email from you. Could you send to email link for downloading if its possible?

    0
    Comment actions Permalink

    Hello, I'll send to alexandrbelkin87@gmail.com again. 

    0
    Comment actions Permalink

    Thank you for your support. But I still didn't get email from you. Could you send to email link for downloading if its possible?

    0
    Comment actions Permalink

    Dear Linda, I can't download the file you sent me. It says Idon't have an access.

    0
    Comment actions Permalink

    Hello.

    The problem isn't solved yet. My s19j Pro is still s19j after flashing with:

    Antminer-S19j-Pro-Release-sd2nand-zynq7007-20210605.zip
    S19j Pro SD firmware for 7007 control board only
    26.87MB, 2021-08-26

    Here is the log file:

    On node 0 totalpages: 61440
    free_area_init_node: node 0, pgdat c0b3c040, node_mem_map cde10000
      Normal zone: 480 pages used for memmap
      Normal zone: 0 pages reserved
      Normal zone: 61440 pages, LIFO batch:15
    percpu: Embedded 12 pages/cpu @cddf0000 s19916 r8192 d21044 u49152
    pcpu-alloc: s19916 r8192 d21044 u49152 alloc=12*4096
    pcpu-alloc: [0] 0 [0] 1 
    Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
    Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
    PID hash table entries: 1024 (order: 0, 4096 bytes)
    Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
    Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
    Memory: 209668K/245760K available (6317K kernel code, 243K rwdata, 1932K rodata, 1024K init, 232K bss, 19708K reserved, 16384K cma-reserved, 0K highmem)
    Virtual kernel memory layout:
        vector  : 0xffff0000 - 0xffff1000   (   4 kB)
        fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
        vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
        lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
        pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
        modules : 0xbf000000 - 0xbfe00000   (  14 MB)
          .text : 0xc0008000 - 0xc090e410   (9242 kB)
          .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
          .data : 0xc0b00000 - 0xc0b3cda0   ( 244 kB)
           .bss : 0xc0b3cda0 - 0xc0b77024   ( 233 kB)
    Preemptible hierarchical RCU implementation.
    	Build-time adjustment of leaf fanout to 32.
    	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
    RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
    NR_IRQS:16 nr_irqs:16 16
    efuse mapped to cf800000
    ps7-slcr mapped to cf802000
    L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
    L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
    L2C-310 erratum 769419 enabled
    L2C-310 enabling early BRESP for Cortex-A9
    L2C-310 full line of zeros enabled for Cortex-A9
    L2C-310 ID prefetch enabled, offset 1 lines
    L2C-310 dynamic clock gating enabled, standby mode enabled
    L2C-310 cache controller enabled, 8 ways, 512 kB
    L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
    zynq_clock_init: clkc starts at cf802100
    Zynq clock init
    sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
    clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
    Switching to timer-based delay loop, resolution 3ns
    clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
    ps7-ttc #0 at cf80a000, irq=18
    Console: colour dummy device 80x30
    Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
    pid_max: default: 32768 minimum: 301
    Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
    Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
    CPU: Testing write buffer coherency: ok
    CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
    Setting up static identity map for 0x100000 - 0x100058
    CPU1: failed to boot: -1
    Brought up 1 CPUs
    SMP: Total of 1 processors activated (666.66 BogoMIPS).
    CPU: All CPU(s) started in SVC mode.
    devtmpfs: initialized
    VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
    clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
    pinctrl core: initialized pinctrl subsystem
    NET: Registered protocol family 16
    DMA: preallocated 256 KiB pool for atomic coherent allocations
    cpuidle: using governor menu
    hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
    hw-breakpoint: maximum watchpoint size is 4 bytes.
    zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
    vgaarb: loaded
    SCSI subsystem initialized
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    media: Linux media interface: v0.10
    Linux video capture interface: v2.00
    pps_core: LinuxPPS API ver. 1 registered
    pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    PTP clock support registered
    EDAC MC: Ver: 3.0.0
    Advanced Linux Sound Architecture Driver Initialized.
    clocksource: Switched to clocksource arm_global_timer
    NET: Registered protocol family 2
    TCP established hash table entries: 2048 (order: 1, 8192 bytes)
    TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
    TCP: Hash tables configured (established 2048 bind 2048)
    UDP hash table entries: 256 (order: 1, 8192 bytes)
    UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
    NET: Registered protocol family 1
    RPC: Registered named UNIX socket transport module.
    RPC: Registered udp transport module.
    RPC: Registered tcp transport module.
    RPC: Registered tcp NFSv4.1 backchannel transport module.
    PCI: CLS 0 bytes, default 64
    Trying to unpack rootfs image as initramfs...
    rootfs image is not initramfs (no cpio magic); looks like an initrd
    Freeing initrd memory: 6636K (cd47e000 - cdaf9000)
    hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
    futex hash table entries: 512 (order: 3, 32768 bytes)
    workingset: timestamp_bits=28 max_order=16 bucket_order=0
    jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
    io scheduler noop registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
    dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
    e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 159, base_baud = 6249999) is a xuartps
    console [ttyPS0] enabled
    xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
    [drm] Initialized drm 1.1.0 20060810
    brd: module loaded
    loop: module loaded
    CAN device driver interface
    gpiod_set_value: invalid GPIO
    libphy: MACB_mii_bus: probed
    macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
    Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
    e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
    e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    ehci-pci: EHCI PCI platform driver
    usbcore: registered new interface driver usb-storage
    mousedev: PS/2 mouse device common for all mice
    i2c /dev entries driver
    cdns-i2c e0005000.ps7_i2c: 100 kHz mmio e0005000 irq 154
    Xilinx Zynq CpuIdle Driver started
    sdhci: Secure Digital Host Controller Interface driver
    sdhci: Copyright(c) Pierre Ossman
    sdhci-pltfm: SDHCI platform and OF driver helper
    mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
    ledtrig-cpu: registered to indicate activity on CPUs
    usbcore: registered new interface driver usbhid
    usbhid: USB HID core driver
    nand: disable subpage write
    nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
    nand: Micron MT29F2G08ABAEAWP
    nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
    nand: NAND_ECC_HW
    nand: NAND_ECC_HW_SYNDROME
    mtd->writesize = 2048
    ecc->strength = 1
    ecc->size = 2048
    mtd->writesize = 2048
    chip->ecc_strength_ds = 4
    chip->ecc_step_ds = 512
    nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
    Bad block table found at page 131008, version 0x01
    Bad block table found at page 130944, version 0x01
    8 ofpart partitions found on MTD device pl35x-nand
    Creating 8 MTD partitions on "pl35x-nand":
    0x000000000000-0x000002800000 : "BOOT.bin-dts-marker-kernel"
    0x000002800000-0x000004800000 : "ramfs"
    0x000004800000-0x000005000000 : "configs"
    0x000005000000-0x000005200000 : "sig"
    0x000005200000-0x000006000000 : "reserve1"
    0x000006000000-0x000007000000 : "upgrade-ramfs"
    0x000007000000-0x00000a800000 : "upgrade-file"
    0x00000a800000-0x000010000000 : "reserve2"
    nf_conntrack version 0.5.0 (3635 buckets, 14540 max)
    ip_tables: (C) 2000-2006 Netfilter Core Team
    NET: Registered protocol family 10
    ip6_tables: (C) 2000-2006 Netfilter Core Team
    sit: IPv6 over IPv4 tunneling driver
    NET: Registered protocol family 17
    can: controller area network core (rev 20120528 abi 9)
    NET: Registered protocol family 29
    can: raw protocol (rev 20120528)
    can: broadcast manager protocol (rev 20120528 t)
    can: netlink gateway (rev 20130117) max_hops=1
    zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
    zynq_pm_late_init: Unable to map DDRC IO memory.
    Registering SWP/SWPB emulation handler
    hctosys: unable to open rtc device (rtc0)
    ALSA device list:
      No soundcards found.
    RAMDISK: gzip image found at block 0
    EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
    EXT4-fs warning (device ram0): ext4_update_dynamic_rev:746: updating to rev 1 because of new feature flag, running e2fsck is recommended
    EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
    VFS: Mounted root (ext4 filesystem) on device 1:0.
    devtmpfs: mounted
    Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
    EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr,errors=remount-ro
    devpts: called with bogus options
    ubi0: attaching mtd2
    ubi0: scanning is finished
    ubi0: attached mtd2 (name "configs", size 8 MiB)
    ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
    ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
    ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
    ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
    ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
    ubi0: max/mean erase counter: 7/2, WL threshold: 4096, image sequence number: 262741923
    ubi0: available PEBs: 36, total reserved PEBs: 28, PEBs reserved for bad PEB handling: 4
    ubi0: background thread "ubi_bgt0d" started, PID 729
    UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 733
    UBIFS (ubi0:0): recovery needed
    UBIFS (ubi0:0): recovery completed
    UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
    UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
    UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
    UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
    UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID A9E8BDA4-70DE-45D9-83BE-2DD9F129C0C6, small LPT model
    ubi2: attaching mtd4
    ubi2: scanning is finished
    ubi2: attached mtd4 (name "reserve1", size 14 MiB)
    ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
    ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
    ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096
    ubi2: good PEBs: 112, bad PEBs: 0, corrupted PEBs: 0
    ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128
    ubi2: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 2358093750
    ubi2: available PEBs: 0, total reserved PEBs: 112, PEBs reserved for bad PEB handling: 4
    ubi2: background thread "ubi_bgt2d" started, PID 740
    UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 744
    UBIFS (ubi2:0): recovery needed
    UBIFS (ubi2:0): recovery completed
    UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "misc"
    UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
    UBIFS (ubi2:0): FS size: 11935744 bytes (11 MiB, 94 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
    UBIFS (ubi2:0): reserved for root: 563754 bytes (550 KiB)
    UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID 2084752D-6223-4908-826E-076ED3B498E5, small LPT model
    IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    random: avahi-daemon urandom read with 2 bits of entropy available
    macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
    macb e000b000.ethernet eth0: link up (100/Full)
    IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    In axi fpga driver!
    request_mem_region OK!
    AXI fpga dev virtual address is 0xcfbc8000
    *base_vir_addr = 0xb031
    In fpga mem driver!
    request_mem_region OK!
    fpga mem virtual address is 0xd2000000
    
    
    ===========================================Miner log===========================================
    1970-01-01 00:00:09 Miner compile time: Sat Jun  5 23:30:08 CST 2021 type: Antminer S19j
    1970-01-01 00:00:10 This is fix-freq version
    1970-01-01 00:00:10 Miner compile time: Sat Jun  5 23:30:08 CST 2021 type: Antminer S19j
    1970-01-01 00:00:10 commit version: e02de5b 2021-06-05 22:56:34, build by: jenkins 2021-06-05 23:30:07
    1970-01-01 00:00:10 opt_multi_version     = 1
    1970-01-01 00:00:10 opt_bitmain_ab        = 1
    1970-01-01 00:00:10 mid_auto_gen          = 0
    1970-01-01 00:00:10 opt_bitmain_work_mode = 0
    1970-01-01 00:00:10 mmap fpga_mem_addr_hal = 0xb5800000
    1970-01-01 00:00:10 HASH_ON_PLUG V9 = 0x7
    1970-01-01 00:00:10 Note: front fan is power on!
    1970-01-01 00:00:10 Note: rear fan is power on!
    1970-01-01 00:00:10 start the http log.
    1970-01-01 00:00:10 httpListenThread start ret=0
    1970-01-01 00:00:10 start listen on 6060 ...
    1970-01-01 00:00:10 load machine BHB42701 conf
    1970-01-01 00:00:10 machine : BHB42701 
    1970-01-01 00:00:10 chain_num 4, chain_domain_num 36, chain_asic_num 108, domain_asic_num 3
    1970-01-01 00:00:16 miner ID : 80040d267910481c
    1970-01-01 00:00:16 FPGA Version = 0xB031
    1970-01-01 00:00:16 HASH_ON_PLUG V9 = 0x7
    1970-01-01 00:00:16 ==========================capability start==========================
    1970-01-01 00:00:16 board num = 3
    1970-01-01 00:00:16 board id = 0, chain num = 1
    1970-01-01 00:00:16 	chain id = 0
    1970-01-01 00:00:16 board id = 1, chain num = 1
    1970-01-01 00:00:16 	chain id = 1
    1970-01-01 00:00:16 board id = 2, chain num = 1
    1970-01-01 00:00:16 	chain id = 2
    1970-01-01 00:00:16 ==========================capability end============================
    1970-01-01 00:00:16 chain num = 3
    2021-11-05 05:06:25 load chain 0 eeprom data
    2021-11-05 05:06:25 FW type BHB42701, eeprom[0] shows BHB42601
    2021-11-05 05:06:27 load chain 1 eeprom data
    2021-11-05 05:06:27 FW type BHB42701, eeprom[1] shows BHB42601
    2021-11-05 05:06:28 load chain 2 eeprom data
    2021-11-05 05:06:28 FW type BHB42701, eeprom[2] shows BHB42601
    2021-11-05 05:06:28 Sweep error string = J255:4.
    2021-11-05 05:06:28 Fixture data load failed, exit.
    2021-11-05 05:06:28 ERROR_SOC_INIT: basic init failed!
    2021-11-05 05:06:28 stop_mining: basic init failed!
    2021-11-05 05:06:28 ****power off hashboard****
    2021-11-05 05:06:30 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0xff, read_back_data[1] = 0xff
    2021-11-05 05:06:30 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0xff, read_back_data[1] = 0xff
    2021-11-05 05:06:30 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0xff, read_back_data[1] = 0xff

    Yesterday, support manager adviced me to flash my device with firmware by clicking on the link https://service.bitmain.com/support/download 

    "Antminer-S19j-Pro-release-202106281212.bin"
    27.35MB
    S19j Pro release firmware
    The firmware cann't be upgraded by current official APMinerTools(V1.0.11) and other like BTC tool,etc. Please upgrated it by miner web administration page.
    2021-07-09

    But unfortunately, flashing didn't give any result, because after choosing this firmware in the web interface, page reloads and nothing happens.

     

    Could you please send to my email correct firmware for my s19j pro, so I could flash it via SD card?

    Maybe it would be something like recovery firmware for s 19j pro.

    Also, to prevent theese situations in the future, maybe it's time to correct the downloading link for the firmware Antminer-S19j-Pro-Release-sd2nand-zynq7007-20210605.zip?

    0
    Comment actions Permalink

    Good afternoon,
    Here is such a problem on 2 S19J pro devices.

    [    0.000000] Booting Linux on physical CPU 0x0
    [    0.000000] Initializing cgroup subsys cpu
    [    0.000000] Linux version 3.8.13+ (jenkins@nomd-nomd-fwc-bj) (gcc version 4.9.4 (Linaro GCC 4.9-2017.01) ) #12 SMP Tue Oct 19 21:33:04 CST 2021
    [    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d
    [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
    [    0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone
    [    0.000000] Memory policy: ECC disabled, Data cache writeback
    [    0.000000] On node 0 totalpages: 65280
    [    0.000000] free_area_init_node: node 0, pgdat c05db000, node_mem_map c0633000
    [    0.000000]   Normal zone: 512 pages used for memmap
    [    0.000000]   Normal zone: 0 pages reserved
    [    0.000000]   Normal zone: 64768 pages, LIFO batch:15
    [    0.000000] AM335X ES1.0 (neon )
    [    0.000000] PERCPU: Embedded 8 pages/cpu @c0840000 s9856 r8192 d14720 u32768
    [    0.000000] pcpu-alloc: s9856 r8192 d14720 u32768 alloc=8*4096
    [    0.000000] pcpu-alloc: [0] 0 
    [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64768
    [    0.000000] Kernel command line: console=ttyO0,115200n8 init=/sbin/init
    [    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
    [    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
    [    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
    [    0.000000] __ex_table already sorted, skipping sort
    [    0.000000] allocated 524288 bytes of page_cgroup
    [    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [    0.000000] Memory: 255MB = 255MB total
    [    0.000000] Memory: 245432k/245432k available, 16712k reserved, 0K highmem
    [    0.000000] Virtual kernel memory layout:
    [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    [    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    [    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
    [    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
    [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    [    0.000000]     modules : 0xbf800000 - 0xbfe00000   (   6 MB)
    [    0.000000]       .text : 0xc0008000 - 0xc0540674   (5346 kB)
    [    0.000000]       .init : 0xc0541000 - 0xc0572680   ( 198 kB)
    [    0.000000]       .data : 0xc0574000 - 0xc05dbee0   ( 416 kB)
    [    0.000000]        .bss : 0xc05dbee0 - 0xc0632448   ( 346 kB)
    [    0.000000] Hierarchical RCU implementation.
    [    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
    [    0.000000] NR_IRQS:16 nr_irqs:16 16
    [    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
    [    0.000000] Total of 128 interrupts on 1 active controller
    [    0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz
    [    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
    [    0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz
    [    0.000000] Console: colour dummy device 80x30
    [    0.000351] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968)
    [    0.015447] pid_max: default: 32768 minimum: 301
    [    0.015671] Security Framework initialized
    [    0.015763] Mount-cache hash table entries: 512
    [    0.024259] Initializing cgroup subsys cpuacct
    [    0.024290] Initializing cgroup subsys memory
    [    0.024353] Initializing cgroup subsys blkio
    [    0.024486] CPU: Testing write buffer coherency: ok
    [    0.024991] CPU0: thread -1, cpu 0, socket -1, mpidr 0
    [    0.025063] Setting up static identity map for 0x8030a500 - 0x8030a54c
    [    0.026429] Brought up 1 CPUs
    [    0.026451] SMP: Total of 1 processors activated (545.07 BogoMIPS).
    [    0.027729] devtmpfs: initialized
    [    0.091515] pinctrl core: initialized pinctrl subsystem
    [    0.091759] rstctl core: initialized rstctl subsystem
    [    0.092227] regulator-dummy: no parameters
    [    0.092726] NET: Registered protocol family 16
    [    0.093385] DMA: preallocated 256 KiB pool for atomic coherent allocations
    [    0.102811] pinctrl-single 44e10800.pinmux: prop pinctrl-0 index 0 invalid phandle
    [    0.102985] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
    [    0.104027] platform 49000000.edma: alias fck already exists
    [    0.104057] platform 49000000.edma: alias fck already exists
    [    0.104082] platform 49000000.edma: alias fck already exists
    [    0.105204] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
    [    0.105432] OMAP GPIO hardware version 0.1
    [    0.106767] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
    [    0.108068] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
    [    0.109515] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
    [    0.110029] of_get_named_gpio_flags exited with status 52
    [    0.110058] gpio-rctrl rstctl.3: loaded OK
    [    0.114923] omap-gpmc 50000000.gpmc: GPMC revision 6.0
    [    0.118178] hw-breakpoint: debug architecture 0x4 unsupported.
    [    0.120083] cpsw.0: No hwaddr in dt. Using 3c:a3:08:5e:22:0e from efuse
    [    0.128994] bio: create slab <bio-0> at 0
    [    0.140475] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver
    [    0.140720] of_get_named_gpio_flags: can't parse gpios property
    [    0.140946] vmmcsd_fixed: 3300 mV 
    [    0.144072] SCSI subsystem initialized
    [    0.145310] omap_i2c 4819c000.i2c: bus 0 rev0.11 at 100 kHz
    [    0.145342] omap_i2c 4819c000.i2c: unable to select pin group
    [    0.145574] pps_core: LinuxPPS API ver. 1 registered
    [    0.145591] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    [    0.147177] Switching to clocksource gp_timer
    [    0.164347] NET: Registered protocol family 2
    [    0.165410] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
    [    0.165498] TCP bind hash table entries: 2048 (order: 3, 40960 bytes)
    [    0.165592] TCP: Hash tables configured (established 2048 bind 2048)
    [    0.165687] TCP: reno registered
    [    0.165712] UDP hash table entries: 256 (order: 1, 12288 bytes)
    [    0.165757] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
    [    0.166167] NET: Registered protocol family 1
    [    0.166735] RPC: Registered named UNIX socket transport module.
    [    0.166755] RPC: Registered udp transport module.
    [    0.166768] RPC: Registered tcp transport module.
    [    0.166841] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [    0.167228] Trying to unpack rootfs image as initramfs...
    [    1.057568] Freeing initrd memory: 6456K
    [    1.058197] CPU PMU: probing PMU on CPU 0
    [    1.058226] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
    [    1.058745] omap2_mbox_probe: platform not supported
    [    1.062507] VFS: Disk quotas dquot_6.5.2
    [    1.062750] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    [    1.064128] NFS: Registering the id_resolver key type
    [    1.064220] Key type id_resolver registered
    [    1.064237] Key type id_legacy registered
    [    1.064300] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
    [    1.064738] msgmni has been set to 491
    [    1.067557] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
    [    1.067581] io scheduler noop registered
    [    1.067597] io scheduler deadline registered
    [    1.067653] io scheduler cfq registered (default)
    [    1.071381] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
    [    1.073631] omap_uart 44e09000.serial: did not get pins for uart0 error: -19
    [    1.073654] of_get_named_gpio_flags: can't parse gpios property
    [    1.073923] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0
    [    1.695044] console [ttyO0] enabled
    [    1.699304] of_get_named_gpio_flags: can't parse gpios property
    [    1.699549] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89) is a OMAP UART1
    [    1.708012] of_get_named_gpio_flags: can't parse gpios property
    [    1.708227] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90) is a OMAP UART2
    [    1.716612] of_get_named_gpio_flags: can't parse gpios property
    [    1.716823] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61) is a OMAP UART4
    [    1.725215] of_get_named_gpio_flags: can't parse gpios property
    [    1.725478] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 62) is a OMAP UART5
    [    1.747355] brd: module loaded
    [    1.757618] loop: module loaded
    [    1.761662] bone-capemgr bone_capemgr.8: Failed to find baseboard eeprom node
    [    1.771721] ONFI param page 0 valid
    [    1.775434] ONFI flash detected
    [    1.778758] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xf1 (Micron MT29F1G08ABAEAWP), 128MiB, page size: 2048, OOB size: 64
    [    1.790683] omap2-nand: detected x8 NAND flash
    [    1.795352] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme
    [    1.800937] omap2-nand: using custom ecc layout
    [    1.805790] 12 ofpart partitions found on MTD device omap2-nand.0
    [    1.812191] Creating 12 MTD partitions on "omap2-nand.0":
    [    1.817874] 0x000000000000-0x000000020000 : "spl"
    [    1.824545] 0x000000020000-0x000000040000 : "spl_backup1"
    [    1.831896] 0x000000040000-0x000000060000 : "spl_backup2"
    [    1.839260] 0x000000060000-0x000000080000 : "spl_backup3"
    [    1.846602] 0x000000080000-0x000000240000 : "u-boot"
    [    1.854913] 0x000000240000-0x000000260000 : "bootenv"
    [    1.861867] 0x000000260000-0x000000280000 : "fdt"
    [    1.868501] 0x000000280000-0x000000780000 : "kernel"
    [    1.879378] 0x000000800000-0x000001c00000 : "root"
    [    1.902692] 0x000001c00000-0x000001e00000 : "config"
    [    1.911124] 0x000001e00000-0x000002000000 : "sig"
    [    1.919294] 0x000002000000-0x000008000000 : "nvdata"
    [    2.007043] OneNAND driver initializing
    [    2.013445] mousedev: PS/2 mouse device common for all mice
    [    2.021169] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0
    [    2.028934] i2c /dev entries driver
    [    2.033244] pps_ldisc: PPS line discipline registered
    [    2.038734] Driver for 1-wire Dallas network protocol.
    [    2.045967] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
    [    2.053566] cpuidle: using governor ladder
    [    2.057890] cpuidle: using governor menu
    [    2.062473] of_get_named_gpio_flags exited with status 6
    [    2.062492] of_get_named_gpio_flags: can't parse gpios property
    [    2.062507] of_get_named_gpio_flags: can't parse gpios property
    [    2.062543] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed
    [    2.069776] omap_hsmmc mmc.4: Failed to get rstctl; not using any
    [    2.076578] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25
    [    2.083800] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24
    [    2.091122] mmc.4 supply vmmc_aux not found, using dummy regulator
    [    2.098093] omap_hsmmc mmc.4: pins are not configured from the driver
    [    2.132248] of_get_named_gpio_flags exited with status -517
    [    2.132315] platform gpio-leds.7: Driver leds-gpio requests probe deferral
    [    2.140104] ledtrig-cpu: registered to indicate activity on CPUs
    [    2.146882] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36
    [    2.154082] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
    [    2.162141] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
    [    2.168427] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5
    [    2.175611] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6
    [    2.183918] nf_conntrack version 0.5.0 (3935 buckets, 15740 max)
    [    2.191389] ip_tables: (C) 2000-2006 Netfilter Core Team
    [    2.197171] TCP: cubic registered
    [    2.200710] Initializing XFRM netlink socket
    [    2.205347] NET: Registered protocol family 10
    [    2.211450] ip6_tables: (C) 2000-2006 Netfilter Core Team
    [    2.217407] NET: Registered protocol family 17
    [    2.222183] NET: Registered protocol family 15
    [    2.227020] Key type dns_resolver registered
    [    2.231602] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
    [    2.239688] ThumbEE CPU extension supported.
    [    2.244207] Registering SWP/SWPB emulation handler
    [    2.250324] registered taskstats version 1
    [    2.256094] of_get_named_gpio_flags exited with status -517
    [    2.256166] platform gpio-leds.7: Driver leds-gpio requests probe deferral
    [    2.313352] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6
    [    2.319768] davinci_mdio 4a101000.mdio: detected phy mask fffffffe
    [    2.334584] libphy: 4a101000.mdio: probed
    [    2.338938] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720
    [    2.349024] of_get_named_gpio_flags exited with status -517
    [    2.349089] platform gpio-leds.7: Driver leds-gpio requests probe deferral
    [    2.356577] Detected MACID = 3c:a3:08:5e:22:0e
    [    2.361258] cpsw 4a100000.ethernet: NAPI disabled
    [    2.368228] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
    [    2.377411] cpu0 supply cpu0 not found, using dummy regulator
    [    2.383904] cpufreq_cpu0: failed to scale voltage up: -22
    [    2.389733] cpufreq_cpu0: failed to scale voltage up: -22
    [    2.403454] Freeing init memory: 196K
    [    2.483975] devpts: called with bogus options
    [    2.936872] jffs2: notice: (109) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
    [    3.816055] jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x021dcff0: Read 0xffffffff, calculated 0x944382e9
    [    3.868445] omap_elm_correct_data(1295)
    [    3.872611] omap_elm_correct_data(1298)
    [    4.218163] jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x0364dff0: Read 0xffffffff, calculated 0x12a8645c
    [    5.181540] jffs2: notice: (115) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
    [    5.631964] net eth0: initializing cpsw version 1.12 (0)
    [    5.640224] net eth0: phy found : id is : 0x7c0f1
    [    5.654668] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    [    6.219743] omap_elm_correct_data(1295)
    [    6.223916] omap_elm_correct_data(1298)
    [    6.252774] omap_elm_correct_data(1295)
    [    6.256927] omap_elm_correct_data(1298)
    [    6.265090] omap_elm_correct_data(1295)
    [    6.269250] omap_elm_correct_data(1298)
    [    6.346526] omap_elm_correct_data(1295)
    [    6.350679] omap_elm_correct_data(1298)
    [    6.470533] omap_elm_correct_data(1295)
    [    6.474690] omap_elm_correct_data(1298)
    [    6.632623] omap_elm_correct_data(1295)
    [    6.636773] omap_elm_correct_data(1298)
    [    6.768398] omap_elm_correct_data(1295)
    [    6.772540] omap_elm_correct_data(1298)
    [    6.911920] omap_elm_correct_data(1295)
    [    6.916086] omap_elm_correct_data(1298)
    [    7.033962] omap_elm_correct_data(1295)
    [    7.038125] omap_elm_correct_data(1298)
    [    7.100782] omap_elm_correct_data(1295)
    [    7.104966] omap_elm_correct_data(1298)
    [    7.157095] omap_elm_correct_data(1295)
    [    7.161260] omap_elm_correct_data(1298)
    [    7.241057] omap_elm_correct_data(1295)
    [    7.245215] omap_elm_correct_data(1298)
    [    7.283341] omap_elm_correct_data(1295)
    [    7.287488] omap_elm_correct_data(1298)
    [    7.307434] omap_elm_correct_data(1295)
    [    7.311585] omap_elm_correct_data(1298)
    [    7.356407] omap_elm_correct_data(1295)
    [    7.360563] omap_elm_correct_data(1298)
    [    8.171143] omap_elm_correct_data(1295)
    [    8.175312] omap_elm_correct_data(1298)
    [    8.295744] omap_elm_correct_data(1295)
    [    8.299886] omap_elm_correct_data(1298)
    [    8.361310] omap_elm_correct_data(1295)
    [    8.365454] omap_elm_correct_data(1298)
    [    8.506653] omap_elm_correct_data(1295)
    [    8.510808] omap_elm_correct_data(1298)
    [    8.868035] omap_elm_correct_data(1295)
    [    8.872189] omap_elm_correct_data(1298)
    [    9.075052] omap_elm_correct_data(1295)
    [    9.079213] omap_elm_correct_data(1298)
    [    9.786919] libphy: 4a101000.mdio:00 - Link is Up - 100/Half
    [    9.796282] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [    9.836801] omap_elm_correct_data(1295)
    [    9.840961] omap_elm_correct_data(1298)
    [    9.851064] omap_elm_correct_data(1295)
    [    9.855220] omap_elm_correct_data(1298)
    [   10.082832] omap_elm_correct_data(1295)
    [   10.086981] omap_elm_correct_data(1298)
    [   10.111667] omap_elm_correct_data(1295)
    [   10.115822] omap_elm_correct_data(1298)
    [   10.283019] omap_elm_correct_data(1295)
    [   10.287192] omap_elm_correct_data(1298)
    [   10.324366] omap_elm_correct_data(1295)
    [   10.328524] omap_elm_correct_data(1298)
    [   10.468577] omap_elm_correct_data(1295)
    [   10.472734] omap_elm_correct_data(1298)
    [   10.564978] jffs2: notice: (116) check_node_data: wrong data CRC in data node at 0x00fd42b8: read 0xf4ce655c, calculated 0x93d9ff8c.
    [   10.677580] omap_elm_correct_data(1295)
    [   10.681736] omap_elm_correct_data(1298)
    [   10.766422] omap_elm_correct_data(1295)
    [   10.770576] omap_elm_correct_data(1298)
    [   10.785496] omap_elm_correct_data(1295)
    [   10.789644] omap_elm_correct_data(1298)
    [   10.982687] omap_elm_correct_data(1295)
    [   10.986855] omap_elm_correct_data(1298)
    [   11.051907] omap_elm_correct_data(1295)
    [   11.056056] omap_elm_correct_data(1298)
    [   11.119112] omap_elm_correct_data(1295)
    [   11.123268] omap_elm_correct_data(1298)
    [   11.243566] register uart_trans chrdev success.
    [   11.249066] tty port open success [/dev/ttyO1]!
    [   11.254030] init sucess for tty struct (249:1)  [/dev/ttyO1]
    [   11.260418] tty port open success [/dev/ttyO2]!
    [   11.267460] init sucess for tty struct (249:2)  [/dev/ttyO2]
    [   11.273861] tty port open success [/dev/ttyO4]!
    [   11.278825] init sucess for tty struct (249:4)  [/dev/ttyO4]
    [   11.285184] tty port open success [/dev/ttyO5]!
    [   11.290157] init sucess for tty struct (249:5)  [/dev/ttyO5]
    [   11.434536] omap_elm_correct_data(1295)
    [   11.438703] omap_elm_correct_data(1298)
    [   11.700031] omap_elm_correct_data(1295)
    [   11.704206] omap_elm_correct_data(1298)
    [   11.954408] omap_elm_correct_data(1295)
    [   11.958580] omap_elm_correct_data(1298)
    [   12.133639] omap_elm_correct_data(1295)
    [   12.137807] omap_elm_correct_data(1298)
    [   12.164740] omap_elm_correct_data(1295)
    [   12.168917] omap_elm_correct_data(1298)
    [   12.674141] omap_elm_correct_data(1295)
    [   12.678296] omap_elm_correct_data(1298)
    [   12.687509] omap_elm_correct_data(1295)
    [   12.691658] omap_elm_correct_data(1298)
    [   13.365056] omap_elm_correct_data(1295)
    [   13.369236] omap_elm_correct_data(1298)
    [   13.431670] omap_elm_correct_data(1295)
    [   13.435830] omap_elm_correct_data(1298)
    [   13.601400] omap_elm_correct_data(1295)
    [   13.605570] omap_elm_correct_data(1298)
    [   14.206091] omap_elm_correct_data(1295)
    [   14.210254] omap_elm_correct_data(1298)
    [   14.328921] omap_elm_correct_data(1295)
    [   14.333067] omap_elm_correct_data(1298)
    [   14.434004] omap_elm_correct_data(1295)
    [   14.438153] omap_elm_correct_data(1298)
    [   14.593604] omap_elm_correct_data(1295)
    [   14.597774] omap_elm_correct_data(1298)
    [   15.118997] omap_elm_correct_data(1295)
    [   15.123175] omap_elm_correct_data(1298)
    [   15.523729] omap_elm_correct_data(1295)
    [   15.527909] omap_elm_correct_data(1298)
    [   15.714660] omap_elm_correct_data(1295)
    [   15.718818] omap_elm_correct_data(1298)
    [   15.819293] omap_elm_correct_data(1295)
    [   15.823455] omap_elm_correct_data(1298)
    [   15.888842] omap_elm_correct_data(1295)
    [   15.893003] omap_elm_correct_data(1298)
    [   15.951967] omap_elm_correct_data(1295)
    [   15.956128] omap_elm_correct_data(1298)
    [   16.176128] omap_elm_correct_data(1295)
    [   16.180318] omap_elm_correct_data(1298)
    [   16.442218] omap_elm_correct_data(1295)
    [   16.446384] omap_elm_correct_data(1298)
    [   16.465207] omap_elm_correct_data(1295)
    [   16.469369] omap_elm_correct_data(1298)
    [   16.864109] omap_elm_correct_data(1295)
    [   16.868286] omap_elm_correct_data(1298)
    [   16.898703] omap_elm_correct_data(1295)
    [   16.902849] omap_elm_correct_data(1298)
    [   16.991755] omap_elm_correct_data(1295)
    [   16.995928] omap_elm_correct_data(1298)
    [   17.034161] omap_elm_correct_data(1295)
    [   17.038310] omap_elm_correct_data(1298)
    [   27.757837] omap_elm_correct_data(1295)
    [   27.762003] omap_elm_correct_data(1298)
    [   27.790953] omap_elm_correct_data(1295)
    [   27.795154] omap_elm_correct_data(1298)
    [   27.803437] omap_elm_correct_data(1295)
    [   27.807607] omap_elm_correct_data(1298)
    [   27.885904] omap_elm_correct_data(1295)
    [   27.890066] omap_elm_correct_data(1298)
    [   28.009520] omap_elm_correct_data(1295)
    [   28.013674] omap_elm_correct_data(1298)
    [   28.168630] omap_elm_correct_data(1295)
    [   28.172822] omap_elm_correct_data(1298)
    [   28.311720] omap_elm_correct_data(1295)
    [   28.315896] omap_elm_correct_data(1298)
    [   28.564810] omap_elm_correct_data(1295)
    [   28.568975] omap_elm_correct_data(1298)
    [   28.625676] omap_elm_correct_data(1295)
    [   28.629868] omap_elm_correct_data(1298)
    [   28.682294] omap_elm_correct_data(1295)
    [   28.686453] omap_elm_correct_data(1298)
    [   28.765923] omap_elm_correct_data(1295)
    [   28.770086] omap_elm_correct_data(1298)
    [   28.808824] omap_elm_correct_data(1295)
    [   28.812987] omap_elm_correct_data(1298)
    [   28.835491] omap_elm_correct_data(1295)
    [   28.839668] omap_elm_correct_data(1298)
    [   28.882498] omap_elm_correct_data(1295)
    [   28.886647] omap_elm_correct_data(1298)
    [   29.681445] omap_elm_correct_data(1295)
    [   29.685620] omap_elm_correct_data(1298)
    [   29.805054] omap_elm_correct_data(1295)
    [   29.809223] omap_elm_correct_data(1298)
    [   29.877454] omap_elm_correct_data(1295)
    [   29.881644] omap_elm_correct_data(1298)
    [   30.023962] omap_elm_correct_data(1295)
    [   30.028151] omap_elm_correct_data(1298)
    [   30.389819] omap_elm_correct_data(1295)
    [   30.393990] omap_elm_correct_data(1298)
    [   30.593552] omap_elm_correct_data(1295)
    [   30.597720] omap_elm_correct_data(1298)
    [   31.292816] omap_elm_correct_data(1295)
    [   31.296988] omap_elm_correct_data(1298)
    [   31.307494] omap_elm_correct_data(1295)
    [   31.311655] omap_elm_correct_data(1298)
    [   31.601691] omap_elm_correct_data(1295)
    [   31.605886] omap_elm_correct_data(1298)
    [   31.631822] omap_elm_correct_data(1295)
    [   31.635987] omap_elm_correct_data(1298)
    [   31.791077] omap_elm_correct_data(1295)
    [   31.795280] omap_elm_correct_data(1298)
    [   31.833695] omap_elm_correct_data(1295)
    [   31.837843] omap_elm_correct_data(1298)
    [   31.977630] omap_elm_correct_data(1295)
    [   31.981791] omap_elm_correct_data(1298)
    
    
    ===========================================Miner log===========================================
    2000-01-01 00:00:09 Miner compile time: Tue Oct 19 21:43:15 CST 2021 type: Antminer S19j Pro
    2000-01-01 00:00:15 This is fix-freq version
    2000-01-01 00:00:15 Miner compile time: Tue Oct 19 21:43:15 CST 2021 type: Antminer S19j Pro
    2000-01-01 00:00:15 commit version: ce69be1 2021-10-19 19:57:55, build by: jenkins 2021-10-19 22:01:40
    2000-01-01 00:00:15 opt_multi_version     = 1
    2000-01-01 00:00:15 opt_bitmain_ab        = 1
    2000-01-01 00:00:15 mid_auto_gen          = 1
    2000-01-01 00:00:15 opt_bitmain_work_mode = 0
    2000-01-01 00:00:15 port 51 already exported
    2000-01-01 00:00:15 port 49 already exported
    2000-01-01 00:00:15 no board pluged in socket 51
    2000-01-01 00:00:15 port 48 already exported
    2000-01-01 00:00:15 port 60 already exported
    2000-01-01 00:00:15 port 47 already exported
    2000-01-01 00:00:15 port 27 already exported
    2000-01-01 00:00:15 port 44 already exported
    2000-01-01 00:00:15 port 22 already exported
    2000-01-01 00:00:15 port 23 already exported
    2000-01-01 00:00:15 port 45 already exported
    2000-01-01 00:00:15 port 46 already exported
    2000-01-01 00:00:15 port 26 already exported
    2000-01-01 00:00:15 Note: front fan is power on!
    2000-01-01 00:00:15 Note: rear fan is power on!
    2000-01-01 00:00:15 start the http log.
    2000-01-01 00:00:15 httpListenThread start ret=0
    2000-01-01 00:00:15 start listen on 6060 ...
    2000-01-01 00:00:15 load machine BHB42601 conf
    2000-01-01 00:00:15 machine : BHB42601 
    2000-01-01 00:00:15 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
    2000-01-01 00:00:20 ==========================capability start==========================
    2000-01-01 00:00:20 board num = 3
    2000-01-01 00:00:20 board id = 1, chain num = 1
    2000-01-01 00:00:20 	chain id = 1
    2000-01-01 00:00:20 board id = 2, chain num = 1
    2000-01-01 00:00:20 	chain id = 2
    2000-01-01 00:00:20 board id = 3, chain num = 1
    2000-01-01 00:00:20 	chain id = 3
    2000-01-01 00:00:20 ==========================capability end============================
    2000-01-01 00:00:20 chain num = 3
    2000-01-01 00:00:21 load chain 1 eeprom data
    2000-01-01 00:00:21 FW type BHB42601, eeprom[1] shows BHB42631
    2000-01-01 00:00:22 load chain 2 eeprom data
    2000-01-01 00:00:22 FW type BHB42601, eeprom[2] shows BHB42631
    2000-01-01 00:00:22 load chain 3 eeprom data
    2000-01-01 00:00:22 FW type BHB42601, eeprom[3] shows BHB42631
    2000-01-01 00:00:22 Sweep error string = J14:4.
    2000-01-01 00:00:22 Fixture data load failed, exit.
    2000-01-01 00:00:22 ERROR_SOC_INIT: basic init failed!
    2000-01-01 00:00:22 stop_mining: basic init failed!
    2000-01-01 00:00:22 ****power off hashboard****
    2000-01-01 00:00:23 fail to write 0:7
    2000-01-01 00:00:23 fail to write 1:7
    2000-01-01 00:00:23 fail to write 2:7
    2000-01-01 00:00:23 fail to write 3:7
    2000-01-01 00:00:23 fail to write 4:7
    2000-01-01 00:00:23 fail to write 5:7
    2000-01-01 00:00:23 fail to write 6:7
    2000-01-01 00:00:24 fail to read 0:2
    2000-01-01 00:00:24 fail to read 1:2
    2000-01-01 00:00:24 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0x00, read_back_data[1] = 0x00
    2000-01-01 00:00:24 fail to write 0:7
    2000-01-01 00:00:24 fail to write 1:7
    2000-01-01 00:00:24 fail to write 2:7
    2000-01-01 00:00:24 fail to write 3:7
    2000-01-01 00:00:24 fail to write 4:7
    2000-01-01 00:00:24 fail to write 5:7
    2000-01-01 00:00:24 fail to write 6:7
    2000-01-01 00:00:24 fail to read 0:2
    2000-01-01 00:00:24 fail to read 1:2
    2000-01-01 00:00:24 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0x00, read_back_data[1] = 0x00
    2000-01-01 00:00:24 fail to write 0:7
    2000-01-01 00:00:24 fail to write 1:7
    2000-01-01 00:00:24 fail to write 2:7
    2000-01-01 00:00:24 fail to write 3:7
    2000-01-01 00:00:24 fail to write 4:7
    2000-01-01 00:00:24 fail to write 5:7
    2000-01-01 00:00:24 fail to write 6:7
    2000-01-01 00:00:24 fail to read 0:2
    2000-01-01 00:00:24 fail to read 1:2
    2000-01-01 00:00:24 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0x00, read_back_data[1] = 0x00
    0
    Comment actions Permalink

    Antminer S19j Pro updating the firmware via the web interface did not lead to anything. Please send the correct firmware to kolyanjis60@gmail.com

    0
    Comment actions Permalink

    Hello. Please sent correct firmware Antminer-S19j-Pro-Release-sd2nand-zynq7007 to eugen.safonov2016@gmail.com

    Thank you

    0
    Comment actions Permalink

    Hello I'm having a similar problem. Please send firmware to lincoln@negawatt-engineering.com

    ===========================================Miner log===========================================
    1970-01-01 00:00:09 Miner compile time: Sat Jun  5 23:30:08 CST 2021 type: Antminer S19j
    1970-01-01 00:00:10 This is fix-freq version
    1970-01-01 00:00:10 Miner compile time: Sat Jun  5 23:30:08 CST 2021 type: Antminer S19j
    1970-01-01 00:00:10 commit version: e02de5b 2021-06-05 22:56:34, build by: jenkins 2021-06-05 23:30:07
    1970-01-01 00:00:10 opt_multi_version     = 1
    1970-01-01 00:00:11 opt_bitmain_ab        = 1
    1970-01-01 00:00:11 mid_auto_gen          = 0
    1970-01-01 00:00:11 opt_bitmain_work_mode = 0
    1970-01-01 00:00:11 mmap fpga_mem_addr_hal = 0xb5800000
    1970-01-01 00:00:11 HASH_ON_PLUG V9 = 0x7
    1970-01-01 00:00:11 Note: front fan is power on!
    1970-01-01 00:00:11 Note: rear fan is power on!
    1970-01-01 00:00:11 start the http log.
    1970-01-01 00:00:11 httpListenThread start ret=0
    1970-01-01 00:00:11 start listen on 6060 ...
    1970-01-01 00:00:11 load machine BHB42701 conf
    1970-01-01 00:00:11 machine : BHB42701 
    1970-01-01 00:00:11 chain_num 4, chain_domain_num 36, chain_asic_num 108, domain_asic_num 3
    2022-09-02 00:29:06 miner ID : 8072ac2429e04814
    2022-09-02 00:29:06 FPGA Version = 0xB031
    2022-09-02 00:29:06 HASH_ON_PLUG V9 = 0x7
    2022-09-02 00:29:06 ==========================capability start==========================
    2022-09-02 00:29:06 board num = 3
    2022-09-02 00:29:06 board id = 0, chain num = 1
    2022-09-02 00:29:06 	chain id = 0
    2022-09-02 00:29:06 board id = 1, chain num = 1
    2022-09-02 00:29:06 	chain id = 1
    2022-09-02 00:29:06 board id = 2, chain num = 1
    2022-09-02 00:29:06 	chain id = 2
    2022-09-02 00:29:06 ==========================capability end============================
    2022-09-02 00:29:06 chain num = 3
    2022-09-02 00:29:08 load chain 0 eeprom data
    2022-09-02 00:29:08 FW type BHB42701, eeprom[0] shows BHB42601
    2022-09-02 00:29:10 load chain 1 eeprom data
    2022-09-02 00:29:10 FW type BHB42701, eeprom[1] shows BHB42601
    2022-09-02 00:29:12 load chain 2 eeprom data
    2022-09-02 00:29:12 FW type BHB42701, eeprom[2] shows BHB42601
    2022-09-02 00:29:12 Sweep error string = J255:4.
    2022-09-02 00:29:12 Fixture data load failed, exit.
    2022-09-02 00:29:12 ERROR_SOC_INIT: basic init failed!
    2022-09-02 00:29:12 stop_mining: basic init failed!
    2022-09-02 00:29:12 ****power off hashboard****
    2022-09-02 00:29:13 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0xff, read_back_data[1] = 0xff
    2022-09-02 00:29:13 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0xff, read_back_data[1] = 0xff
    2022-09-02 00:29:14 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0xff, read_back_data[1] = 0xff
    0
    Comment actions Permalink

    I also having the  same issue and until now there is no solution

    Bitmain support please try to mail me the correct firmware to juanthina@gmail.com

    My miner model is S19 90TH , AM logic Control board A113D. 

    I have done upgrading firmware in web and sd card still same.

     

     


    [    0.000000@0] Booting Linux on physical CPU 0x0
    [    0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Fri Nov 19 22:32:14 CST 2021
    [    0.000000@0] Boot CPU: AArch64 Processor [410fd034]
    [    0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '')
    [    0.000000@0] bootconsole [aml_uart0] enabled
    [    0.000000@0] efi: Getting EFI parameters from FDT:
    [    0.000000@0] efi: UEFI not found.
    [    0.000000@0]     07400000 - 07500000,     1024 KB, ramoops@0x07400000
    [    0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB
    [    0.000000@0]     05000000 - 05400000,     4096 KB, linux,secmon
    [    0.000000@0] __reserved_mem_alloc_size, start:0x000000003e000000, end:0x0000000040000000, len:32 MiB
    [    0.000000@0] failed to allocate memory for node linux,meson-fb, size:32 MB
    [    0.000000@0] cma: Reserved 8 MiB at 0x000000000f800000
    [    0.000000@0] On node 0 totalpages: 65536
    [    0.000000@0]   DMA zone: 1024 pages used for memmap
    [    0.000000@0]   DMA zone: 0 pages reserved
    [    0.000000@0]   DMA zone: 65536 pages, LIFO batch:15
    [    0.000000@0] psci: probing for conduit method from DT.
    [    0.000000@0] psci: PSCIv1.0 detected in firmware.
    [    0.000000@0] psci: Using standard PSCI v0.2 function IDs
    [    0.000000@0] psci: MIGRATE_INFO_TYPE not supported.
    [    0.000000@0] psci: SMC Calling Convention v1.1
    [    0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00f753000 s64536 r8192 d29672 u102400
    [    0.000000@0] pcpu-alloc: s64536 r8192 d29672 u102400 alloc=25*4096
    [    0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
    [    0.000000@0] Detected VIPT I-cache on CPU0
    [    0.000000@0] CPU features: enabling workaround for ARM erratum 845719
    [    0.000000@0] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64512
    [    0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 rootfstype=ramfs init=/sbin/init
    [    0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes)
    [    0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
    [    0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
    [    0.000000@0] Memory: 219920K/262144K available (8764K kernel code, 1194K rwdata, 2428K rodata, 3648K init, 1018K bss, 29936K reserved, 12288K cma-reserved)
    [    0.000000@0] Virtual kernel memory layout:
    [    0.000000@0]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
    [    0.000000@0]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)
    [    0.000000@0]       .text : 0xffffff8009080000 - 0xffffff8009910000   (  8768 KB)
    [    0.000000@0]     .rodata : 0xffffff8009910000 - 0xffffff8009b80000   (  2496 KB)
    [    0.000000@0]       .init : 0xffffff8009b80000 - 0xffffff8009f10000   (  3648 KB)
    [    0.000000@0]       .data : 0xffffff8009f10000 - 0xffffff800a03aa00   (  1195 KB)
    [    0.000000@0]        .bss : 0xffffff800a03aa00 - 0xffffff800a139534   (  1019 KB)
    [    0.000000@0]     fixed   : 0xffffffbefe7fb000 - 0xffffffbefec00000   (  4116 KB)
    [    0.000000@0]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)
    [    0.000000@0]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)
    [    0.000000@0]               0xffffffbf00000000 - 0xffffffbf00400000   (     4 MB actual)
    [    0.000000@0]     memory  : 0xffffffc000000000 - 0xffffffc010000000   (   256 MB)
    [    0.000000@0] can't find symbol:arm_dma_alloc
    [    0.000000@0] can't find symbol:__alloc_from_contiguous
    [    0.000000@0] can't find symbol:cma_allocator_alloc
    [    0.000000@0]  0, addr:ffffff800971cff0 +  140, aml_cma_alloc_post_hook
    [    0.000000@0]  1, addr:ffffff800951f258 +   78, dma_alloc_from_contiguous
    [    0.000000@0]  2, addr:ffffff80091fdd50 +  388, cma_alloc
    [    0.000000@0]  3, addr:ffffff80091f76c8 +  2d0, __kmalloc_track_caller
    [    0.000000@0]  4, addr:ffffff80091f4a70 +  2d0, __kmalloc
    [    0.000000@0]  5, addr:ffffff80091f4750 +  258, kmem_cache_alloc_trace
    [    0.000000@0]  6, addr:ffffff80091f4500 +  250, kmem_cache_alloc
    [    0.000000@0]  7, addr:ffffff80091f4490 +   70, __slab_alloc.isra.24.constprop.28
    [    0.000000@0]  8, addr:ffffff80091f4108 +  388, ___slab_alloc.constprop.29
    [    0.000000@0]  9, addr:ffffff80091f1e70 +  420, new_slab
    [    0.000000@0] 10, addr:ffffff80091e52f8 +   b0, vzalloc
    [    0.000000@0] 11, addr:ffffff80091e5248 +   b0, vmalloc
    [    0.000000@0] 12, addr:ffffff80091e4b00 +  2e0, __vmalloc_node_range
    [    0.000000@0] 13, addr:ffffff80091ca410 +  110, kmalloc_order_trace
    [    0.000000@0] 14, addr:ffffff80091ca2a0 +  170, kmalloc_order
    [    0.000000@0] 15, addr:ffffff80091ab5a8 +  168, __alloc_page_frag
    [    0.000000@0] 16, addr:ffffff80091ab540 +   68, alloc_pages_exact
    [    0.000000@0] 17, addr:ffffff80091ab510 +   30, get_zeroed_page
    [    0.000000@0] 18, addr:ffffff80091ab4b8 +   58, __get_free_pages
    [    0.000000@0] 19, addr:ffffff80091aa800 +  cb8, __alloc_pages_nodemask
    [    0.000000@0] 20, addr:ffffff800909c6e8 +  2a8, __dma_alloc
    [    0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    [    0.000000@0] Preemptible hierarchical RCU implementation.
    [    0.000000@0]     Build-time adjustment of leaf fanout to 64.
    [    0.000000@0]     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
    [    0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
    [    0.000000@0] 
    [    0.000000@0] **********************************************************
    [    0.000000@0] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
    [    0.000000@0] **                                                      **
    [    0.000000@0] ** trace_printk() being used. Allocating extra memory.  **
    [    0.000000@0] **                                                      **
    [    0.000000@0] ** This means that this is a DEBUG kernel and it is     **
    [    0.000000@0] ** unsafe for production use.                           **
    [    0.000000@0] **                                                      **
    [    0.000000@0] ** If you see this message and you are not debugging    **
    [    0.000000@0] ** the kernel, report this immediately to your vendor!  **
    [    0.000000@0] **                                                      **
    [    0.000000@0] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
    [    0.000000@0] **********************************************************
    [    0.000000@0] NR_IRQS:64 nr_irqs:64 0
    [    0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
    [    0.000000@0] axg_aoclkc_init: register ao clk ok!
    [    0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
    [    0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
    [    0.000000@0] axg_amlogic_init_media: register meson media clk
    [    0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks
    [    0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk
    [    0.000000@0] axg_clkc_init initialization complete
    [    0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
    [    0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
    [    0.000003@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
    [    0.008251@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194
    [    0.016914@0] Console: colour dummy device 80x25
    [    0.021106@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
    [    0.031586@0] pid_max: default: 32768 minimum: 301
    [    0.036440@0] thread_stack_cache_init, vmap:ffffffc00edaf600, bitmap:ffffffc00eda3000, cache page:ede0
    [    0.045772@0] thread_stack_cache_init, allocation vm area:ffffffc00edd94c0, addr:ffffff8020000000, size:20001000
    [    0.056005@0] cpu 0, vmap_stack:[ffffffc00f75c960-ffffffc00f760950]
    [    0.062304@0] cpu 0, irq_stack: [ffffffc00f753060-ffffffc00f757050]
    [    0.068603@0] cpu 1, vmap_stack:[ffffffc00f775960-ffffffc00f779950]
    [    0.074903@0] cpu 1, irq_stack: [ffffffc00f76c060-ffffffc00f770050]
    [    0.081203@0] cpu 2, vmap_stack:[ffffffc00f78e960-ffffffc00f792950]
    [    0.087503@0] cpu 2, irq_stack: [ffffffc00f785060-ffffffc00f789050]
    [    0.093803@0] cpu 3, vmap_stack:[ffffffc00f7a7960-ffffffc00f7ab950]
    [    0.100103@0] cpu 3, irq_stack: [ffffffc00f79e060-ffffffc00f7a2050]
    [    0.106464@0] Security Framework initialized
    [    0.110696@0] SELinux:  Initializing.
    [    0.114389@0] SELinux:  Starting in permissive mode
    [    0.114427@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
    [    0.121108@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
    [    0.128868@0] ftrace: allocating 30089 entries in 118 pages
    [    0.184482@0] sched-energy: CPU device node has no sched-energy-costs
    [    0.185291@0] CPU0: update cpu_capacity 1024
    [    0.189618@0] ASID allocator initialised with 32768 entries
    [    0.227599@0] secmon: can't fine clear_range
    [    0.227808@0] EFI services will not be available.
    [    0.231084@0] Meson chip version = RevC (25:C - 23:0)
    [    0.264950@1] Detected VIPT I-cache on CPU1
    [    0.265010@1] CPU1: update cpu_capacity 1024
    [    0.265012@1] CPU1: Booted secondary processor [410fd034]
    [    0.293013@2] Detected VIPT I-cache on CPU2
    [    0.293067@2] CPU2: update cpu_capacity 1024
    [    0.293070@2] CPU2: Booted secondary processor [410fd034]
    [    0.321076@3] Detected VIPT I-cache on CPU3
    [    0.321128@3] CPU3: update cpu_capacity 1024
    [    0.321130@3] CPU3: Booted secondary processor [410fd034]
    [    0.321220@0] Brought up 4 CPUs
    [    0.360438@0] SMP: Total of 4 processors activated.
    [    0.365347@0] CPU features: detected feature: 32-bit EL0 Support
    [    0.371383@0] CPU features: detected feature: Kernel page table isolation (KPTI)
    [    0.381948@0] CPU: All CPU(s) started at EL2
    [    0.383123@0] alternatives: patching kernel code
    [    0.388448@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755
    [    0.395652@0] devtmpfs: initialized
    [    0.411089@0] DMI not present or invalid.
    [    0.411451@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
    [    0.419466@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
    [    0.426024@0] pinctrl core: initialized pinctrl subsystem
    [    0.432457@0] NET: Registered protocol family 16
    [    0.463949@2] cpuidle: using governor menu
    [    0.464443@2] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000)
    [    0.470063@2] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers.
    [    0.477488@3] DMA: preallocated 256 KiB pool for atomic allocations
    [    0.483610@3] clkmsr: clkmsr: driver init
    [    0.487683@3] aml_watch_point_probe, in, wp:2
    [    0.492236@3] pstore: using zlib compression
    [    0.496592@3] console [pstore-1] enabled
    [    0.499940@3] pstore: Registered ramoops as persistent store backend
    [    0.506341@3] ramoops: attached 0x100000@0x7400000, ecc: 0/0
    [    0.520719@3] aml_iomap: amlogic iomap probe done
    [    0.527738@3] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c
    [    0.529664@3] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0
    [    0.619141@3] usbcore: registered new interface driver usbfs
    [    0.619333@3] usbcore: registered new interface driver hub
    [    0.624925@3] usbcore: registered new device driver usb
    [    0.630260@3] pps_core: LinuxPPS API ver. 1 registered
    [    0.635148@3] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    [    0.644546@3] PTP clock support registered
    [    0.648930@3] dmi: Firmware registration failed.
    [    0.653875@3] secmon: reserve_mem_size:0x300000
    [    0.657907@3] secmon secmon: assigned reserved memory node linux,secmon
    [    0.664806@3] secmon: get page:ffffffbf00140000, 5000
    [    0.669521@3] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000
    [    0.677902@3] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
    [    0.685851@3] NetLabel: Initializing
    [    0.687952@3] NetLabel:  domain hash size = 128
    [    0.692529@3] NetLabel:  protocols = UNLABELED CIPSOv4
    [    0.697783@3] NetLabel:  unlabeled traffic allowed by default
    [    0.704370@3] clocksource: Switched to clocksource arch_sys_counter
    [    0.833725@3] VFS: Disk quotas dquot_6.6.0
    [    0.833872@3] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [    0.860323@1] NET: Registered protocol family 2
    [    0.861506@1] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
    [    0.866566@1] TCP bind hash table entries: 2048 (order: 3, 32768 bytes)
    [    0.873293@1] TCP: Hash tables configured (established 2048 bind 2048)
    [    0.879818@1] UDP hash table entries: 256 (order: 1, 8192 bytes)
    [    0.885785@1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
    [    0.892568@1] NET: Registered protocol family 1
    [    0.897484@1] RPC: Registered named UNIX socket transport module.
    [    0.902929@1] RPC: Registered udp transport module.
    [    0.907799@1] RPC: Registered tcp transport module.
    [    0.912697@1] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [    0.921956@1] Unpacking initramfs...
    [    1.422487@1] Initramfs unpacking failed: junk in compressed archive
    [    1.429362@1] Freeing initrd memory: 6536K
    [    1.430240@1] hw perfevents: clusterb_enabled = 0
    [    1.432618@1] hw perfevents: cpumasks 0xf, 0x0
    [    1.437073@1] hw perfevents: cluster A irq = 7
    [    1.441638@1] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
    [    1.451838@1] audit: initializing netlink subsys (disabled)
    [    1.455162@1] audit: type=2000 audit(1.316:1): initialized
    [    1.462431@1] workingset: timestamp_bits=62 max_order=16 bucket_order=0
    [    1.487663@3] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    1.494790@3] NFS: Registering the id_resolver key type
    [    1.494876@3] Key type id_resolver registered
    [    1.498816@3] Key type id_legacy registered
    [    1.503430@3] fuse init (API version 7.26)
    [    1.508966@3] SELinux:  Registering netfilter hooks
    [    1.515235@3] NET: Registered protocol family 38
    [    1.515297@3] Key type asymmetric registered
    [    1.518542@3] Asymmetric key parser 'x509' registered
    [    1.524054@3] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
    [    1.531235@3] io scheduler noop registered (default)
    [    1.536212@3] io scheduler deadline registered
    [    1.541121@3] io scheduler cfq registered
    [    1.562067@2] random: fast init done
    [    1.562167@2] random: crng init done
    [    1.562636@3] Unable to detect cache hierarchy for CPU 0
    [    1.603466@3] loop: module loaded
    [    1.605087@3] zram: Added device: zram0
    [    1.605555@3] mtdoops: mtd device (mtddev=name/number) must be supplied
    [    1.612140@3] libphy: Fixed MDIO Bus: probed
    [    1.616869@3] tun: Universal TUN/TAP device driver, 1.6
    [    1.621210@3] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
    [    1.629423@3]  ee eth reset:Addr = ffffff80081fd008
    [    1.632852@3] meson6-dwmac ff3f0000.ethernet: no reset control found
    [    1.638879@3] stmmac - user ID: 0x11, Synopsys ID: 0x37
    [    1.644111@3]  Ring mode enabled
    [    1.647348@3]  DMA HW capability register supported
    [    1.652072@3]  Normal descriptors
    [    1.655397@3]  RX Checksum Offload Engine supported
    [    1.660297@3]     COE Type 2
    [    1.662921@3]  TX Checksum insertion supported
    [    1.667387@3]  Wake-Up On Lan supported
    [    1.671331@3]  Enable RX Mitigation via HW Watchdog Timer
    [    1.684913@3] libphy: stmmac: probed
    [    1.684964@3] eth%d: PHY ID 0007c0f1 at 0 IRQ POLL (stmmac-0:00) active
    [    1.691442@3] PPP generic driver version 2.4.2
    [    1.694418@3] PPP BSD Compression module registered
    [    1.698902@3] PPP Deflate Compression module registered
    [    1.704151@3] PPP MPPE Compression module registered
    [    1.709118@3] NET: Registered protocol family 24
    [    1.714633@3] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [    1.720516@3] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [    1.727564@3] usbcore: registered new interface driver cdc_acm
    [    1.732765@3] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
    [    1.741209@3] usbcore: registered new interface driver usbserial
    [    1.747929@2] mousedev: PS/2 mouse device common for all mice
    [    1.753334@2] usbcore: registered new interface driver xpad
    [    1.758738@3] i2c /dev entries driver
    [    1.763552@3] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
    [    1.767762@3] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
    [    1.778681@3] ff803000.serial: clock gate not found
    [    1.780225@3] meson_uart ff803000.serial: ==uart0 reg addr = ffffff800830d000
    [    1.787469@3] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 13, base_baud = 1500000) is a meson_uart
    [    1.802377@3] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200
    [    1.805080@3] console [ttyS0] enabled
    [    1.812297@3] bootconsole [aml_uart0] disabled
    [    1.821975@1] ff804000.serial: clock gate not found
    [    1.826087@1] meson_uart ff804000.serial: ==uart3 reg addr = ffffff8008321000
    [    1.833193@1] ff804000.serial: ttyS3 at MMIO 0xff804000 (irq = 14, base_baud = 1500000) is a meson_uart
    [    1.843568@2] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff8008323000
    [    1.849710@2] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 25, base_baud = 1500000) is a meson_uart
    [    1.859861@3] meson_uart ffd23000.serial: ==uart2 reg addr = ffffff8008325000
    [    1.866184@3] ffd23000.serial: ttyS2 at MMIO 0xffd23000 (irq = 26, base_baud = 1500000) is a meson_uart
    [    1.877242@0] amlogic-new-usb2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff8008348000
    [    1.886420@0] amlogic-new-usb3 ffe09080.usb3phy: This phy has no usb port
    [    1.892923@0] amlogic-new-usb3 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff800834c080
    [    1.907997@0] i2c i2c-1: of_i2c: modalias failure on /soc/aobus@ff800000/i2c@5000/mcu6350@40
    [    1.911751@0] i2c i2c-1: Failed to create I2C device for /soc/aobus@ff800000/i2c@5000/mcu6350@40
    [    1.924045@0] aml_dma ff63e000.aml_dma: Aml dma
    [    1.927306@0] aml_aes_dma ff63e000.aml_dma:aml_aes: Aml AES_dma
    [    1.932227@0] aml_sha_dma ff63e000.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma
    [    1.938659@0] efusekeynum: 4
    [    1.940978@0] efusekeyname:             mac    offset:     0    size:     6
    [    1.947363@0] efusekeyname:          mac_bt    offset:     6    size:     6
    [    1.953765@0] efusekeyname:        mac_wifi    offset:    12    size:     6
    [    1.960190@0] efusekeyname:            usid    offset:    18    size:    16
    [    1.967012@2] efuse efuse: probe OK!
    [    1.972564@2] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller
    [    1.979726@0] meson-mmc: >>>>>>>>hostbase ffffff8008358000, dmode 
    [    1.984850@0] meson-mmc: actual_clock :400000, HHI_nand: 0x80
    [    1.990028@0] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c
    [    2.036513@0] meson-mmc: meson_mmc_probe() : success!
    [    2.036774@0] amlogic mtd driver init
    [    2.040826@0] prase_get_dtb_nand_parameter:128,parse dts start
    [    2.045580@0] bl mode descrete
    [    2.048459@0] fip_copies 4
    [    2.051124@0] fip_size 0x200000
    [    2.054264@0] nand_clk_ctrl 0xffe07000
    [    2.057987@0] prase_get_dtb_nand_parameter:234,parse dts end
    [    2.063655@0] nand_clk_ctrl 0xffe07000
    [    2.067377@0] nand register base ffffff80083df800, nand clock register ffffff80083e1000
    [    2.076114@0] plat->aml_nand_device ffffff800a005a90
    [    2.080311@0] m3_nand_probe() aml_nand_device ffffff800a005a90
    [    2.086350@0] NAND device id: 2c da 90 95 6 0
    [    2.090413@0] NAND device: Manufacturer ID: 
    [    2.094477@0]  0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
    [    2.101519@0] oob_fill_cnt =32 oob_size =64, bch_bytes =14
    [    2.106953@0] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
    [    2.112503@0] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
    [    2.118746@0] mtd->oobavail: 0x8
    [    2.122166@0] aml_nand_init 2119: plat-name:bootloader
    [    2.127070@0] Creating 1 MTD partitions on "bootloader":
    [    2.132370@0] 0x000000000000-0x000000200000 : "bootloader"
    [    2.141474@3] bootloader initialized ok
    [    2.141614@3] plat->aml_nand_device ffffff800a005a90
    [    2.146586@3] m3_nand_probe() aml_nand_device ffffff800a005a90
    [    2.152731@3] NAND device id: 2c da 90 95 6 0
    [    2.156732@3] NAND device: Manufacturer ID: 
    [    2.160787@3]  0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
    [    2.167820@3] oob_fill_cnt =32 oob_size =64, bch_bytes =14
    [    2.173263@3] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
    [    2.178805@3] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
    [    2.185056@3] mtd->oobavail: 0x8
    [    2.188521@3] aml_nand_init 2119: plat-name:nandnormal
    [    2.193410@3] bbt_start=20
    [    2.196028@3] env_start=24
    [    2.198736@3] key_start=32
    [    2.201420@3] dtb_start=40
    [    2.204088@3] ddr_start=44
    [    2.206795@3] nbbt: info size=0x800 max_scan_blk=24, start_blk=20
    [    2.213292@3] get_free_node 43: bitmap=0
    [    2.216762@3] get_free_node 55: bitmap=1
    [    2.220854@3] get_free_node 43: bitmap=1
    [    2.224561@3] get_free_node 55: bitmap=3
    [    2.228653@3] get_free_node 43: bitmap=3
    [    2.232343@3] get_free_node 55: bitmap=7
    [    2.236244@3] nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1
    [    2.242931@3] nbbt free list:
    [    2.245879@3] blockN=21, ec=-1, dirty_flag=0
    [    2.250126@3] blockN=22, ec=-1, dirty_flag=0
    [    2.254372@3] blockN=23, ec=-1, dirty_flag=0
    [    2.258620@3] aml_nand_scan_rsv_info 1141: page_num=1
    [    2.264031@3] nbbt valid addr: 280000
    [    2.267288@3] aml_nand_bbt_check 1306 bbt is valid, reading.
    [    2.272921@3] aml_nand_read_rsv_info:423,read nbbt info at 280000
    [    2.279182@3] nenv: info size=0x10000 max_scan_blk=32, start_blk=24
    [    2.285420@3] get_free_node 43: bitmap=7
    [    2.289127@3] get_free_node 55: bitmap=f
    [    2.293410@3] get_free_node 43: bitmap=f
    [    2.296927@3] get_free_node 55: bitmap=1f
    [    2.301106@3] get_free_node 43: bitmap=1f
    [    2.304900@3] get_free_node 55: bitmap=3f
    [    2.309079@3] get_free_node 43: bitmap=3f
    [    2.312874@3] get_free_node 55: bitmap=7f
    [    2.317053@3] get_free_node 43: bitmap=7f
    [    2.320847@3] get_free_node 55: bitmap=ff
    [    2.325024@3] get_free_node 43: bitmap=ff
    [    2.328821@3] get_free_node 55: bitmap=1ff
    [    2.333086@3] get_free_node 43: bitmap=1ff
    [    2.336967@3] get_free_node 55: bitmap=3ff
    [    2.341040@3] nenv : phy_blk_addr=25, ec=0, phy_page_addr=0, timestamp=2
    [    2.347710@3] nenv free list:
    [    2.350658@3] blockN=24, ec=-1, dirty_flag=0
    [    2.354905@3] blockN=26, ec=-1, dirty_flag=0
    [    2.359152@3] blockN=27, ec=-1, dirty_flag=0
    [    2.363398@3] blockN=28, ec=-1, dirty_flag=0
    [    2.367645@3] blockN=29, ec=-1, dirty_flag=0
    [    2.371892@3] blockN=30, ec=-1, dirty_flag=0
    [    2.376138@3] blockN=31, ec=-1, dirty_flag=0
    [    2.380386@3] aml_nand_scan_rsv_info 1141: page_num=32
    [    2.397752@3] nenv valid addr: 330000
    [    2.397786@3] nkey: info size=0x8000 max_scan_blk=40, start_blk=32
    [    2.402143@3] get_free_node 43: bitmap=3ff
    [    2.406023@3] get_free_node 55: bitmap=7ff
    [    2.410288@3] get_free_node 43: bitmap=7ff
    [    2.414170@3] get_free_node 55: bitmap=fff
    [    2.418435@3] get_free_node 43: bitmap=fff
    [    2.422316@3] get_free_node 55: bitmap=1fff
    [    2.426668@3] get_free_node 43: bitmap=1fff
    [    2.430637@3] get_free_node 55: bitmap=3fff
    [    2.434988@3] get_free_node 43: bitmap=3fff
    [    2.438956@3] get_free_node 55: bitmap=7fff
    [    2.443308@3] get_free_node 43: bitmap=7fff
    [    2.447277@3] get_free_node 55: bitmap=ffff
    [    2.451629@3] get_free_node 43: bitmap=ffff
    [    2.455596@3] get_free_node 55: bitmap=1ffff
    [    2.460036@3] get_free_node 43: bitmap=1ffff
    [    2.464090@3] get_free_node 55: bitmap=3ffff
    [    2.468336@3] nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
    [    2.475007@3] nkey free list:
    [    2.477955@3] blockN=32, ec=-1, dirty_flag=0
    [    2.482201@3] blockN=33, ec=-1, dirty_flag=0
    [    2.486448@3] blockN=34, ec=-1, dirty_flag=0
    [    2.490694@3] blockN=35, ec=-1, dirty_flag=0
    [    2.494940@3] blockN=36, ec=-1, dirty_flag=0
    [    2.499187@3] blockN=37, ec=-1, dirty_flag=0
    [    2.503434@3] blockN=38, ec=-1, dirty_flag=0
    [    2.507680@3] blockN=39, ec=-1, dirty_flag=0
    [    2.511928@3] aml_nand_scan_rsv_info 1141: page_num=16
    [    2.517041@3] nkey valid addr: fffffffffffe0000
    [    2.521549@3] aml_nand_key_check 1251 NO key exist
    [    2.526316@3] ndtb: info size=0x20000 max_scan_blk=44, start_blk=40
    [    2.532802@3] get_free_node 43: bitmap=3ffff
    [    2.536805@3] get_free_node 55: bitmap=7ffff
    [    2.541432@3] get_free_node 43: bitmap=7ffff
    [    2.545297@3] get_free_node 55: bitmap=fffff
    [    2.549736@3] get_free_node 43: bitmap=fffff
    [    2.553790@3] get_free_node 55: bitmap=1fffff
    [    2.558123@3] ndtb : phy_blk_addr=41, ec=0, phy_page_addr=0, timestamp=2
    [    2.564794@3] ndtb free list:
    [    2.567724@3] blockN=40, ec=-1, dirty_flag=0
    [    2.571987@3] blockN=42, ec=-1, dirty_flag=0
    [    2.576234@3] blockN=43, ec=-1, dirty_flag=0
    [    2.580481@3] aml_nand_scan_rsv_info 1141: page_num=64
    [    2.597796@3] ndtb valid addr: 520000
    [    2.597830@3] nddr: info size=0x20000 max_scan_blk=46, start_blk=44
    [    2.602273@3] get_free_node 43: bitmap=1fffff
    [    2.606414@3] get_free_node 55: bitmap=3fffff
    [    2.610940@3] get_free_node 43: bitmap=3fffff
    [    2.615081@3] get_free_node 55: bitmap=7fffff
    [    2.619413@3] nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
    [    2.626084@3] nddr free list:
    [    2.629032@3] blockN=44, ec=-1, dirty_flag=0
    [    2.633278@3] blockN=45, ec=-1, dirty_flag=0
    [    2.637525@3] aml_nand_scan_rsv_info 1141: page_num=64
    [    2.642638@3] nddr valid addr: fffffffffffe0000
    [    2.647145@3] aml_nand_ddr_check 1281 NO ddr exist
    [    2.651916@3] tpl: off 8388608, size 8388608
    [    2.786082@3] Creating 6 MTD partitions on "nandnormal":
    [    2.786129@3] 0x000000800000-0x000001000000 : "tpl"
    [    2.798104@2] 0x000001000000-0x000001200000 : "misc"
    [    2.801401@2] 0x000001200000-0x000002200000 : "recovery"
    [    2.813590@3] 0x000002200000-0x000004200000 : "boot"
    [    2.833112@3] 0x000004200000-0x000004700000 : "config"
    [    2.837868@3] 0x000004700000-0x000010000000 : "nvdata"
    [    2.940794@1] nandnormal initialized ok
    [    2.940906@1] aml_ubootenv_init: register env chardev
    [    2.944657@1] aml_ubootenv_init: register env chardev OK
    [    2.949583@1] amlnf_dtb_init: register dtb cdev
    [    2.954436@1] amlnf_dtb_init: register dtd cdev OK
    [    2.958652@1] mtd_nand_probe 267 , err = 0
    [    2.963988@1] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc0
    [    2.969231@1] input: aml_vkeypad as /devices/platform/rtc/input/input0
    [    2.976465@1] unifykey: storage in base: 0xffffffc005000000
    [    2.980809@1] unifykey: storage out base: 0xffffffc005040000
    [    2.986440@1] unifykey: storage block base: 0xffffffc005080000
    [    2.992233@1] unifykey: probe done!
    [    2.996464@1] unifykey: no efuse-version set, use default value: -1
    [    3.001949@1] unifykey: key unify config unifykey-num is 6
    [    3.007487@1] unifykey: key unify fact unifykey-num is 6
    [    3.012695@1] unifykey: unifykey_devno: f200000
    [    3.017700@2] unifykey: device unifykeys created ok
    [    3.022202@2] unifykey: aml_unifykeys_init done!
    [    3.027084@2] sysled: module init
    [    3.030560@2] meson_wdt ffd0f0d0.watchdog: start watchdog
    [    3.035339@2] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog
    [    3.042745@3] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done
    [    3.051506@0] dmc_monitor_probe
    [    3.052326@0] page_trace_module_init, create sysfs failed
    [    3.058188@0] defendkey defendkey: Reserved memory is not enough!
    [    3.063454@0] defendkey: probe of defendkey failed with error -22
    [    3.069765@0] GACT probability NOT on
    [    3.073146@0] Mirror/redirect action on
    [    3.076932@0] u32 classifier
    [    3.079750@0]     Actions configured
    [    3.083330@0] Netfilter messages via NETLINK v0.30.
    [    3.088637@0] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
    [    3.094821@0] ctnetlink v0.93: registering with nfnetlink.
    [    3.100720@0] xt_time: kernel timezone is -0000
    [    3.104399@0] ipip: IPv4 and MPLS over IPv4 tunneling driver
    [    3.111072@0] ip_tables: (C) 2000-2006 Netfilter Core Team
    [    3.115752@0] arp_tables: arp_tables: (C) 2002 David S. Miller
    [    3.121216@0] Initializing XFRM netlink socket
    [    3.126765@0] NET: Registered protocol family 10
    [    3.132490@0] mip6: Mobile IPv6
    [    3.133274@0] ip6_tables: (C) 2000-2006 Netfilter Core Team
    [    3.139291@0] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
    [    3.147289@0] NET: Registered protocol family 17
    [    3.149538@0] NET: Registered protocol family 15
    [    3.154115@0] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
    [    3.167296@0] l2tp_core: L2TP core driver, V2.0
    [    3.171667@0] l2tp_ppp: PPPoL2TP kernel driver, V2.0
    [    3.176583@0] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
    [    3.182341@0] l2tp_netlink: L2TP netlink interface
    [    3.187144@0] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
    [    3.193210@0] l2tp_debugfs: L2TP debugfs support
    [    3.197725@0] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
    [    3.204414@0] NET: Registered protocol family 35
    [    3.209348@0] Key type dns_resolver registered
    [    3.213873@0] Registered swp emulation handler
    [    3.217765@0] Registered cp15_barrier emulation handler
    [    3.222964@0] Registered setend emulation handler
    [    3.227706@0] disable EAS feature
    [    3.232469@0] registered taskstats version 1
    [    3.249378@3] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host
    [    3.755816@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
    [    3.755909@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
    [    3.764265@3] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f664 hci version 0x100 quirks 0x02010010
    [    3.772630@3] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0xff500000
    [    3.780130@1] hub 1-0:1.0: USB hub found
    [    3.782591@1] hub 1-0:1.0: 1 port detected
    [    3.787198@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
    [    3.792203@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
    [    3.800114@1] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
    [    3.809745@3] hub 2-0:1.0: USB hub found
    [    3.812156@3] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
    [    3.819489@3] usb usb2: Unsupported the hub
    [    3.824322@3] aml_vrtc rtc: setting system clock to 2015-01-01 00:00:08 UTC (1420070408)
    [    3.832319@3] dwc_otg ff400000.dwc2_a: dwc_otg_driver_probe(ffffffc00e17b800)
    [    3.832422@3] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0
    [    3.840280@3] dwc_otg ff400000.dwc2_a: base=0xffffff8008580000
    [    3.840293@3] dwc_otg ff400000.dwc2_a: dwc_otg_device=0xffffffc00c2bb000
    [    3.940818@3] dwc_otg: Core Release: 3.10a
    [    3.940917@3] dwc_otg: Setting default values for core params
    [    3.945069@3] dwc_otg: curmode: 0, host_only: 0
    [    3.949571@3] dwc_otg ff400000.dwc2_a: DMA config: BURST_DEFAULT
    [    3.962107@3] dwc_otg: Using Buffer DMA mode
    [    3.962145@3] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
    [    3.966049@3] dwc_otg: Working on port type = SLAVE
    [    3.970906@3] dwc_otg: Dedicated Tx FIFOs mode
    [    3.978638@3] thermal thermal_zone0: binding zone soc_thermal with cdev thermal-cpufreq-0 failed:-22
    [    3.984626@3] cpucore_cooling_register, max_cpu_core_num:4
    [    3.997219@3] gxbb_pm: enter meson_pm_probe!
    [    3.997277@3] no vddio3v3_en pin
    [    3.998922@3] pm-meson aml_pm: Can't get switch_clk81
    [    4.004029@3] gxbb_pm: meson_pm_probe done
    [    4.008976@3] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
    [    4.015270@3] Freeing unused kernel memory: 3648K
    [    4.029539@3] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
    [    4.294940@0] ubi0: attaching mtd5
    [    4.313851@0] ubi0: scanning is finished
    [    4.318544@2] ubi0: attached mtd5 (name "config", size 5 MiB)
    [    4.318670@2] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
    [    4.325737@2] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
    [    4.332649@2] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
    [    4.339743@2] ubi0: good PEBs: 40, bad PEBs: 0, corrupted PEBs: 0
    [    4.345817@2] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
    [    4.353178@2] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 2315687229
    [    4.362458@2] ubi0: available PEBs: 0, total reserved PEBs: 40, PEBs reserved for bad PEB handling: 4
    [    4.371654@0] ubi0: background thread "ubi_bgt0d" started, PID 1075
    [    4.384914@3] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 1079
    [    4.401408@1] UBIFS (ubi0:0): recovery needed
    [    4.433883@0] UBIFS (ubi0:0): recovery completed
    [    4.434188@0] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "config_data"
    [    4.440899@0] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
    [    4.450948@0] UBIFS (ubi0:0): FS size: 2793472 bytes (2 MiB, 22 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
    [    4.461152@0] UBIFS (ubi0:0): reserved for root: 131942 bytes (128 KiB)
    [    4.467741@0] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 4189DE15-7C1F-4449-A7B1-54440BC76C24, small LPT model
    [    4.492662@1] ubi2: attaching mtd6
    [    5.171677@1] ubi2: scanning is finished
    [    5.178955@1] ubi2: attached mtd6 (name "nvdata", size 185 MiB)
    [    5.179261@1] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
    [    5.186314@1] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
    [    5.193235@1] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096
    [    5.200331@1] ubi2: good PEBs: 1480, bad PEBs: 0, corrupted PEBs: 0
    [    5.206580@1] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128
    [    5.213939@1] ubi2: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 675296445
    [    5.223132@1] ubi2: available PEBs: 0, total reserved PEBs: 1480, PEBs reserved for bad PEB handling: 4
    [    5.232511@0] ubi2: background thread "ubi_bgt2d" started, PID 1087
    [    5.245907@1] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 1091
    [    5.262511@3] UBIFS (ubi2:0): recovery needed
    [    5.298340@2] UBIFS (ubi2:0): recovery completed
    [    5.298646@2] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "nvdata_data"
    [    5.305361@2] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
    [    5.315386@2] UBIFS (ubi2:0): FS size: 185384960 bytes (176 MiB, 1460 LEBs), journal size 9269248 bytes (8 MiB, 73 LEBs)
    [    5.326216@2] UBIFS (ubi2:0): reserved for root: 4952683 bytes (4836 KiB)
    [    5.332978@2] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID C29AD7BA-2B27-48F4-A168-AC84F373756F, small LPT model
    [    5.545833@0] eth0: device MAC address 02:13:83:a3:bc:65
    [    5.629014@3] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP.
    [    5.630302@3] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    [    5.850997@2] uart_trans: loading out-of-tree module taints kernel.
    [    5.853453@2] register uart_trans chrdev success.
    [    5.856771@2] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 0 to 9600
    [    5.864590@2] tty port open success [/dev/ttyS3]!
    [    5.869019@2] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 9600 to 115200
    [    5.877432@2] init sucess for tty struct (246:3)  [/dev/ttyS3]
    [    5.883558@2] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 0 to 9600
    [    5.891201@2] tty port open success [/dev/ttyS2]!
    [    5.895884@2] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 9600 to 115200
    [    5.904287@2] init sucess for tty struct (246:2)  [/dev/ttyS2]
    [    5.910412@2] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 0 to 9600
    [    5.918072@2] tty port open success [/dev/ttyS1]!
    [    5.922740@2] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 115200
    [    5.931147@2] init sucess for tty struct (246:1)  [/dev/ttyS1]
    [    5.937398@3] create workqueue success!
    [    7.684725@3] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
    [    7.688014@3] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [   41.678122@0] nf_conntrack: default automatic helper assignment has been turned off for security reasons and CT-based  firewall rule not found. Use the iptables CT target to attach helpers instead.


    ===========================================Miner log===========================================
    2015-01-01 00:00:15 Miner compile time: Fri Nov 19 22:11:07 CST 2021 type: Antminer S19j Pro
    2015-01-01 00:00:16 This is fix-freq version
    2015-01-01 00:00:16 Miner compile time: Fri Nov 19 22:11:07 CST 2021 type: Antminer S19j Pro
    2015-01-01 00:00:16 commit version: ce69be1 2021-10-19 19:57:55, build by: jenkins 2021-11-19 22:23:40
    2015-01-01 00:00:16 opt_multi_version     = 1
    2015-01-01 00:00:16 opt_bitmain_ab        = 1
    2015-01-01 00:00:16 mid_auto_gen          = 1
    2015-01-01 00:00:16 opt_bitmain_work_mode = 0
    2015-01-01 00:00:16 port 439 already exported
    2015-01-01 00:00:16 port 454 already exported
    2015-01-01 00:00:16 port 440 already exported
    2015-01-01 00:00:16 port 455 already exported
    2015-01-01 00:00:16 port 441 already exported
    2015-01-01 00:00:16 port 456 already exported
    2015-01-01 00:00:16 port 438 already exported
    2015-01-01 00:00:16 port 453 already exported
    2015-01-01 00:00:16 port 446 already exported
    2015-01-01 00:00:16 port 445 already exported
    2015-01-01 00:00:16 Note: front fan is power on!
    2015-01-01 00:00:16 Note: rear fan is power on!
    2015-01-01 00:00:16 start the http log.
    2015-01-01 00:00:16 httpListenThread start ret=0
    2015-01-01 00:00:16 start listen on 6060 ...
    2015-01-01 00:00:16 load machine BHB42601 conf
    2015-01-01 00:00:16 machine : BHB42601 
    2015-01-01 00:00:16 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
    2015-01-01 00:00:16 bad chain id = 3
    2015-01-01 00:00:19 bad chain id = 3
    2015-01-01 00:00:21 ==========================capability start==========================
    2015-01-01 00:00:21 board num = 3
    2015-01-01 00:00:21 board id = 0, chain num = 1
    2015-01-01 00:00:21     chain id = 0
    2015-01-01 00:00:21 board id = 1, chain num = 1
    2015-01-01 00:00:21     chain id = 1
    2015-01-01 00:00:21 board id = 2, chain num = 1
    2015-01-01 00:00:21     chain id = 2
    2015-01-01 00:00:21 ==========================capability end============================
    2015-01-01 00:00:21 chain num = 3
    2022-10-07 06:41:47 load chain 0 eeprom data
    2022-10-07 06:41:47 FW type BHB42601, eeprom[0] shows BHB42801
    2022-10-07 06:41:48 load chain 1 eeprom data
    2022-10-07 06:41:48 EEPROM error: CRC 1ST REGION
    2022-10-07 06:41:48 got nothing
    2022-10-07 06:41:49 load chain 1 eeprom data
    2022-10-07 06:41:49 EEPROM error: CRC 1ST REGION
    2022-10-07 06:41:49 got nothing
    2022-10-07 06:41:49 load chain 1 eeprom data
    2022-10-07 06:41:49 EEPROM error: CRC 1ST REGION
    2022-10-07 06:41:49 got nothing
    2022-10-07 06:41:49 Data load fail for chain 1.
    2022-10-07 06:41:50 load chain 2 eeprom data
    2022-10-07 06:41:50 FW type BHB42601, eeprom[2] shows BHB42801
    2022-10-07 06:41:50 Sweep error string = J7:4.
    2022-10-07 06:41:50 Fixture data load failed, exit.
    2022-10-07 06:41:50 ERROR_SOC_INIT: basic init failed!
    2022-10-07 06:41:50 stop_mining: basic init failed!
    2022-10-07 06:41:50 ****power off hashboard****
    2022-10-07 06:41:51 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0xff, read_back_data[1] = 0xff
    2022-10-07 06:41:52 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0xff, read_back_data[1] = 0xff
    2022-10-07 06:41:52 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0xff, read_back_data[1] = 0xff

    0
    Comment actions Permalink

    Unfortunately I also have the same problem. My email: marcel@aumer.ch and the log below:

    ===========================================Miner log===========================================
    2022-11-23 16:41:17 Miner compile time: Tue Mar 29 13:30:04 CST 2022 type: Antminer BHB42XXX sn :YDFTDXUBBJEJG0F1C
    2022-11-23 16:41:18 This is fix-freq version
    2022-11-23 16:41:18 Miner compile time: Tue Mar 29 13:30:04 CST 2022 type: Antminer BHB42XXX
    2022-11-23 16:41:18 Miner sn: YDFTDXUBBJEJG0F1C
    2022-11-23 16:41:18 commit version: 1956e61 2022-03-29 13:26:30, build by: jenkins 2022-03-29 13:52:24
    2022-11-23 16:41:18 opt_multi_version     = 1
    2022-11-23 16:41:18 opt_bitmain_ab        = 1
    2022-11-23 16:41:18 mid_auto_gen          = 1
    2022-11-23 16:41:18 opt_bitmain_work_mode = 0
    2022-11-23 16:41:18 port 439 already exported
    2022-11-23 16:41:18 port 454 already exported
    2022-11-23 16:41:18 port 440 already exported
    2022-11-23 16:41:18 port 455 already exported
    2022-11-23 16:41:18 port 441 already exported
    2022-11-23 16:41:18 port 456 already exported
    2022-11-23 16:41:18 port 438 already exported
    2022-11-23 16:41:18 port 453 already exported
    2022-11-23 16:41:18 port 446 already exported
    2022-11-23 16:41:18 port 445 already exported
    2022-11-23 16:41:18 Note: front fan is power on!
    2022-11-23 16:41:18 Note: rear fan is power on!
    2022-11-23 16:41:18 start the http log.
    2022-11-23 16:41:18 httpListenThread start ret=0
    2022-11-23 16:41:18 start listen on 6060 ...
    2022-11-23 16:41:18 bad chain id = 3
    2022-11-23 16:41:21 bad chain id = 3
    2022-11-23 16:41:23 ==========================capability start==========================
    2022-11-23 16:41:23 board num = 3
    2022-11-23 16:41:23 board id = 0, chain num = 1
    2022-11-23 16:41:23 	chain id = 0
    2022-11-23 16:41:23 board id = 1, chain num = 1
    2022-11-23 16:41:23 	chain id = 1
    2022-11-23 16:41:23 board id = 2, chain num = 1
    2022-11-23 16:41:23 	chain id = 2
    2022-11-23 16:41:23 ==========================capability end============================
    2022-11-23 16:41:23 chain num = 3
    2022-11-23 16:41:23 skip loading levels for now
    2022-11-23 16:41:24 load chain 0 eeprom data
    2022-11-23 16:41:24 bad_asic_crc = 4,buf[SWEEP_INFO_CRC_OFFSET] = 214
    2022-11-23 16:41:24 EEPROM error: CRC 3ND REGION
    2022-11-23 16:41:25 load chain 1 eeprom data
    2022-11-23 16:41:25 bad_asic_crc = 4,buf[SWEEP_INFO_CRC_OFFSET] = 214
    2022-11-23 16:41:25 EEPROM error: CRC 3ND REGION
    2022-11-23 16:41:25 load chain 2 eeprom data
    2022-11-23 16:41:25 bad_asic_crc = 4,buf[SWEEP_INFO_CRC_OFFSET] = 214
    2022-11-23 16:41:25 EEPROM error: CRC 3ND REGION
    2022-11-23 16:41:25 i2c_sim_init start
    2022-11-23 16:41:25 init gpio477
    2022-11-23 16:41:25 init gpio476
    2022-11-23 16:41:25 i2c_sim_init end
    2022-11-23 16:41:27 power open power_version = 0x75
    2022-11-23 16:41:31 get power version failed
    2022-11-23 16:41:31 power is not Calibrated
    2022-11-23 16:41:33 updated miner type to: Antminer S19j Pro
    2022-11-23 16:41:33 multi machine mode
    2022-11-23 16:41:33 load machine BHB42631 conf
    2022-11-23 16:41:33 machine : BHB42631 
    2022-11-23 16:41:33 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
    2022-11-23 16:41:33 fan_eft : 0  fan_pwm : 100
    2022-11-23 16:41:33 create thread get_nonce_and_register_thread
    2022-11-23 16:41:33 fixed working voltage = 1380
    2022-11-23 16:41:33 Chain [0] PCB Version: 0x0120
    2022-11-23 16:41:33 Chain [0] BOM Version: 0x0020
    2022-11-23 16:41:33 Chain [1] PCB Version: 0x0120
    2022-11-23 16:41:33 Chain [1] BOM Version: 0x0020
    2022-11-23 16:41:33 Chain [2] PCB Version: 0x0120
    2022-11-23 16:41:33 Chain [2] BOM Version: 0x0020
    2022-11-23 16:41:33 bad chain id = 3
    2022-11-23 16:41:33 Fan check passed.
    2022-11-23 16:41:33 uart_trans addr:0xf6f15000.
    2022-11-23 16:41:33 max sensor num = 4
    2022-11-23 16:41:33 STATUS_INITED: soc init done!
    2022-11-23 16:41:33 temperature_monitor_thread start...
    2022-11-23 16:41:35 start to init...
    2022-11-23 16:41:37 power type version: 0x0075
    2022-11-23 16:41:38 disable power watchdog: 0x0000
    2022-11-23 16:41:39 Enter sleep to make sure power release finish.
    0
    Comment actions Permalink

    Unfortunately I also have the same problem after updating the fw. My email: luis@bitcap.co and the log below:

    [    0.000000@0] Booting Linux on physical CPU 0x0
    [    0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Fri Nov 19 22:32:14 CST 2021
    [    0.000000@0] Boot CPU: AArch64 Processor [410fd034]
    [    0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '')
    [    0.000000@0] bootconsole [aml_uart0] enabled
    [    0.000000@0] efi: Getting EFI parameters from FDT:
    [    0.000000@0] efi: UEFI not found.
    [    0.000000@0] 	07400000 - 07500000,     1024 KB, ramoops@0x07400000
    [    0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB
    [    0.000000@0] 	05000000 - 05400000,     4096 KB, linux,secmon
    [    0.000000@0] __reserved_mem_alloc_size, start:0x000000003e000000, end:0x0000000040000000, len:32 MiB
    [    0.000000@0] failed to allocate memory for node linux,meson-fb, size:32 MB
    [    0.000000@0] cma: Reserved 8 MiB at 0x000000000f800000
    [    0.000000@0] On node 0 totalpages: 65536
    [    0.000000@0]   DMA zone: 1024 pages used for memmap
    [    0.000000@0]   DMA zone: 0 pages reserved
    [    0.000000@0]   DMA zone: 65536 pages, LIFO batch:15
    [    0.000000@0] psci: probing for conduit method from DT.
    [    0.000000@0] psci: PSCIv1.0 detected in firmware.
    [    0.000000@0] psci: Using standard PSCI v0.2 function IDs
    [    0.000000@0] psci: MIGRATE_INFO_TYPE not supported.
    [    0.000000@0] psci: SMC Calling Convention v1.1
    [    0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00f753000 s64536 r8192 d29672 u102400
    [    0.000000@0] pcpu-alloc: s64536 r8192 d29672 u102400 alloc=25*4096
    [    0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
    [    0.000000@0] Detected VIPT I-cache on CPU0
    [    0.000000@0] CPU features: enabling workaround for ARM erratum 845719
    [    0.000000@0] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64512
    [    0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 rootfstype=ramfs init=/sbin/init
    [    0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes)
    [    0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
    [    0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
    [    0.000000@0] Memory: 219920K/262144K available (8764K kernel code, 1194K rwdata, 2428K rodata, 3648K init, 1018K bss, 29936K reserved, 12288K cma-reserved)
    [    0.000000@0] Virtual kernel memory layout:
    [    0.000000@0]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
    [    0.000000@0]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)
    [    0.000000@0]       .text : 0xffffff8009080000 - 0xffffff8009910000   (  8768 KB)
    [    0.000000@0]     .rodata : 0xffffff8009910000 - 0xffffff8009b80000   (  2496 KB)
    [    0.000000@0]       .init : 0xffffff8009b80000 - 0xffffff8009f10000   (  3648 KB)
    [    0.000000@0]       .data : 0xffffff8009f10000 - 0xffffff800a03aa00   (  1195 KB)
    [    0.000000@0]        .bss : 0xffffff800a03aa00 - 0xffffff800a139534   (  1019 KB)
    [    0.000000@0]     fixed   : 0xffffffbefe7fb000 - 0xffffffbefec00000   (  4116 KB)
    [    0.000000@0]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)
    [    0.000000@0]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)
    [    0.000000@0]               0xffffffbf00000000 - 0xffffffbf00400000   (     4 MB actual)
    [    0.000000@0]     memory  : 0xffffffc000000000 - 0xffffffc010000000   (   256 MB)
    [    0.000000@0] can't find symbol:arm_dma_alloc
    [    0.000000@0] can't find symbol:__alloc_from_contiguous
    [    0.000000@0] can't find symbol:cma_allocator_alloc
    [    0.000000@0]  0, addr:ffffff800971cff0 +  140, aml_cma_alloc_post_hook
    [    0.000000@0]  1, addr:ffffff800951f258 +   78, dma_alloc_from_contiguous
    [    0.000000@0]  2, addr:ffffff80091fdd50 +  388, cma_alloc
    [    0.000000@0]  3, addr:ffffff80091f76c8 +  2d0, __kmalloc_track_caller
    [    0.000000@0]  4, addr:ffffff80091f4a70 +  2d0, __kmalloc
    [    0.000000@0]  5, addr:ffffff80091f4750 +  258, kmem_cache_alloc_trace
    [    0.000000@0]  6, addr:ffffff80091f4500 +  250, kmem_cache_alloc
    [    0.000000@0]  7, addr:ffffff80091f4490 +   70, __slab_alloc.isra.24.constprop.28
    [    0.000000@0]  8, addr:ffffff80091f4108 +  388, ___slab_alloc.constprop.29
    [    0.000000@0]  9, addr:ffffff80091f1e70 +  420, new_slab
    [    0.000000@0] 10, addr:ffffff80091e52f8 +   b0, vzalloc
    [    0.000000@0] 11, addr:ffffff80091e5248 +   b0, vmalloc
    [    0.000000@0] 12, addr:ffffff80091e4b00 +  2e0, __vmalloc_node_range
    [    0.000000@0] 13, addr:ffffff80091ca410 +  110, kmalloc_order_trace
    [    0.000000@0] 14, addr:ffffff80091ca2a0 +  170, kmalloc_order
    [    0.000000@0] 15, addr:ffffff80091ab5a8 +  168, __alloc_page_frag
    [    0.000000@0] 16, addr:ffffff80091ab540 +   68, alloc_pages_exact
    [    0.000000@0] 17, addr:ffffff80091ab510 +   30, get_zeroed_page
    [    0.000000@0] 18, addr:ffffff80091ab4b8 +   58, __get_free_pages
    [    0.000000@0] 19, addr:ffffff80091aa800 +  cb8, __alloc_pages_nodemask
    [    0.000000@0] 20, addr:ffffff800909c6e8 +  2a8, __dma_alloc
    [    0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    [    0.000000@0] Preemptible hierarchical RCU implementation.
    [    0.000000@0] 	Build-time adjustment of leaf fanout to 64.
    [    0.000000@0] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
    [    0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
    [    0.000000@0] 
    [    0.000000@0] **********************************************************
    [    0.000000@0] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
    [    0.000000@0] **                                                      **
    [    0.000000@0] ** trace_printk() being used. Allocating extra memory.  **
    [    0.000000@0] **                                                      **
    [    0.000000@0] ** This means that this is a DEBUG kernel and it is     **
    [    0.000000@0] ** unsafe for production use.                           **
    [    0.000000@0] **                                                      **
    [    0.000000@0] ** If you see this message and you are not debugging    **
    [    0.000000@0] ** the kernel, report this immediately to your vendor!  **
    [    0.000000@0] **                                                      **
    [    0.000000@0] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
    [    0.000000@0] **********************************************************
    [    0.000000@0] NR_IRQS:64 nr_irqs:64 0
    [    0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
    [    0.000000@0] axg_aoclkc_init: register ao clk ok!
    [    0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
    [    0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
    [    0.000000@0] axg_amlogic_init_media: register meson media clk
    [    0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks
    [    0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk
    [    0.000000@0] axg_clkc_init initialization complete
    [    0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
    [    0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
    [    0.000003@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
    [    0.008251@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194
    [    0.016903@0] Console: colour dummy device 80x25
    [    0.021109@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
    [    0.031586@0] pid_max: default: 32768 minimum: 301
    [    0.036441@0] thread_stack_cache_init, vmap:ffffffc00edaf600, bitmap:ffffffc00eda3000, cache page:ede0
    [    0.045771@0] thread_stack_cache_init, allocation vm area:ffffffc00edd94c0, addr:ffffff8020000000, size:20001000
    [    0.056005@0] cpu 0, vmap_stack:[ffffffc00f75c960-ffffffc00f760950]
    [    0.062304@0] cpu 0, irq_stack: [ffffffc00f753060-ffffffc00f757050]
    [    0.068603@0] cpu 1, vmap_stack:[ffffffc00f775960-ffffffc00f779950]
    [    0.074903@0] cpu 1, irq_stack: [ffffffc00f76c060-ffffffc00f770050]
    [    0.081203@0] cpu 2, vmap_stack:[ffffffc00f78e960-ffffffc00f792950]
    [    0.087503@0] cpu 2, irq_stack: [ffffffc00f785060-ffffffc00f789050]
    [    0.093803@0] cpu 3, vmap_stack:[ffffffc00f7a7960-ffffffc00f7ab950]
    [    0.100103@0] cpu 3, irq_stack: [ffffffc00f79e060-ffffffc00f7a2050]
    [    0.106467@0] Security Framework initialized
    [    0.110696@0] SELinux:  Initializing.
    [    0.114387@0] SELinux:  Starting in permissive mode
    [    0.114425@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
    [    0.121108@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
    [    0.128869@0] ftrace: allocating 30089 entries in 118 pages
    [    0.184516@0] sched-energy: CPU device node has no sched-energy-costs
    [    0.185326@0] CPU0: update cpu_capacity 1024
    [    0.189654@0] ASID allocator initialised with 32768 entries
    [    0.227633@0] secmon: can't fine clear_range
    [    0.227844@0] EFI services will not be available.
    [    0.231121@0] Meson chip version = RevC (25:C - 23:0)
    [    0.264990@1] Detected VIPT I-cache on CPU1
    [    0.265051@1] CPU1: update cpu_capacity 1024
    [    0.265053@1] CPU1: Booted secondary processor [410fd034]
    [    0.293053@2] Detected VIPT I-cache on CPU2
    [    0.293108@2] CPU2: update cpu_capacity 1024
    [    0.293110@2] CPU2: Booted secondary processor [410fd034]
    [    0.321115@3] Detected VIPT I-cache on CPU3
    [    0.321166@3] CPU3: update cpu_capacity 1024
    [    0.321168@3] CPU3: Booted secondary processor [410fd034]
    [    0.321259@0] Brought up 4 CPUs
    [    0.360482@0] SMP: Total of 4 processors activated.
    [    0.365391@0] CPU features: detected feature: 32-bit EL0 Support
    [    0.371427@0] CPU features: detected feature: Kernel page table isolation (KPTI)
    [    0.381994@0] CPU: All CPU(s) started at EL2
    [    0.383168@0] alternatives: patching kernel code
    [    0.388489@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755
    [    0.395697@0] devtmpfs: initialized
    [    0.411124@0] DMI not present or invalid.
    [    0.411485@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
    [    0.419502@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
    [    0.426064@0] pinctrl core: initialized pinctrl subsystem
    [    0.432492@0] NET: Registered protocol family 16
    [    0.451994@0] cpuidle: using governor menu
    [    0.452487@0] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000)
    [    0.458095@0] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers.
    [    0.465538@2] DMA: preallocated 256 KiB pool for atomic allocations
    [    0.471630@2] clkmsr: clkmsr: driver init
    [    0.475734@2] aml_watch_point_probe, in, wp:2
    [    0.480299@2] pstore: using zlib compression
    [    0.484638@2] console [pstore-1] enabled
    [    0.487979@2] pstore: Registered ramoops as persistent store backend
    [    0.494387@2] ramoops: attached 0x100000@0x7400000, ecc: 0/0
    [    0.508761@2] aml_iomap: amlogic iomap probe done
    [    0.515763@2] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c
    [    0.517686@2] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0
    [    0.617807@2] usbcore: registered new interface driver usbfs
    [    0.617960@2] usbcore: registered new interface driver hub
    [    0.624029@2] usbcore: registered new device driver usb
    [    0.628929@2] pps_core: LinuxPPS API ver. 1 registered
    [    0.633821@2] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    [    0.643218@2] PTP clock support registered
    [    0.647560@2] dmi: Firmware registration failed.
    [    0.652558@2] secmon: reserve_mem_size:0x300000
    [    0.656567@2] secmon secmon: assigned reserved memory node linux,secmon
    [    0.663542@2] secmon: get page:ffffffbf00140000, 5000
    [    0.668181@2] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000
    [    0.676582@2] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
    [    0.684491@2] NetLabel: Initializing
    [    0.686623@2] NetLabel:  domain hash size = 128
    [    0.691213@2] NetLabel:  protocols = UNLABELED CIPSOv4
    [    0.696442@2] NetLabel:  unlabeled traffic allowed by default
    [    0.703055@2] clocksource: Switched to clocksource arch_sys_counter
    [    0.832477@2] VFS: Disk quotas dquot_6.6.0
    [    0.832625@2] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [    0.859422@3] NET: Registered protocol family 2
    [    0.860502@3] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
    [    0.865740@3] TCP bind hash table entries: 2048 (order: 3, 32768 bytes)
    [    0.872341@3] TCP: Hash tables configured (established 2048 bind 2048)
    [    0.878910@3] UDP hash table entries: 256 (order: 1, 8192 bytes)
    [    0.884880@3] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
    [    0.891632@3] NET: Registered protocol family 1
    [    0.896604@3] RPC: Registered named UNIX socket transport module.
    [    0.902015@3] RPC: Registered udp transport module.
    [    0.906906@3] RPC: Registered tcp transport module.
    [    0.911795@3] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [    0.921060@3] Unpacking initramfs...
    [    1.421357@3] Initramfs unpacking failed: junk in compressed archive
    [    1.428214@3] Freeing initrd memory: 6536K
    [    1.429117@3] hw perfevents: clusterb_enabled = 0
    [    1.431471@3] hw perfevents: cpumasks 0xf, 0x0
    [    1.435933@3] hw perfevents: cluster A irq = 7
    [    1.440499@3] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
    [    1.450640@3] audit: initializing netlink subsys (disabled)
    [    1.454008@3] audit: type=2000 audit(1.312:1): initialized
    [    1.465386@3] workingset: timestamp_bits=62 max_order=16 bucket_order=0
    [    1.486567@3] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    1.489677@3] NFS: Registering the id_resolver key type
    [    1.492286@3] Key type id_resolver registered
    [    1.496610@3] Key type id_legacy registered
    [    1.501253@3] fuse init (API version 7.26)
    [    1.506687@3] SELinux:  Registering netfilter hooks
    [    1.513053@3] NET: Registered protocol family 38
    [    1.513115@3] Key type asymmetric registered
    [    1.516360@3] Asymmetric key parser 'x509' registered
    [    1.521859@3] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
    [    1.529095@3] io scheduler noop registered (default)
    [    1.534025@3] io scheduler deadline registered
    [    1.538862@3] io scheduler cfq registered
    [    1.559810@0] random: fast init done
    [    1.559910@0] random: crng init done
    [    1.561349@3] Unable to detect cache hierarchy for CPU 0
    [    1.599249@3] loop: module loaded
    [    1.604847@3] zram: Added device: zram0
    [    1.605283@3] mtdoops: mtd device (mtddev=name/number) must be supplied
    [    1.610376@3] libphy: Fixed MDIO Bus: probed
    [    1.614894@3] tun: Universal TUN/TAP device driver, 1.6
    [    1.619271@3] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
    [    1.627525@3]  ee eth reset:Addr = ffffff80081fd008
    [    1.634905@3] meson6-dwmac ff3f0000.ethernet: no reset control found
    [    1.636943@3] stmmac - user ID: 0x11, Synopsys ID: 0x37
    [    1.642180@3]  Ring mode enabled
    [    1.645407@3]  DMA HW capability register supported
    [    1.650139@3]  Normal descriptors
    [    1.653456@3]  RX Checksum Offload Engine supported
    [    1.658361@3] 	COE Type 2
    [    1.660981@3]  TX Checksum insertion supported
    [    1.665443@3]  Wake-Up On Lan supported
    [    1.669388@3]  Enable RX Mitigation via HW Watchdog Timer
    [    1.682852@3] libphy: stmmac: probed
    [    1.682907@3] eth%d: PHY ID 0007c0f1 at 0 IRQ POLL (stmmac-0:00) active
    [    1.689417@3] PPP generic driver version 2.4.2
    [    1.692355@3] PPP BSD Compression module registered
    [    1.696872@3] PPP Deflate Compression module registered
    [    1.702092@3] PPP MPPE Compression module registered
    [    1.707056@3] NET: Registered protocol family 24
    [    1.712531@3] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [    1.718457@3] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [    1.725521@3] usbcore: registered new interface driver cdc_acm
    [    1.730716@3] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
    [    1.739162@3] usbcore: registered new interface driver usbserial
    [    1.745834@2] mousedev: PS/2 mouse device common for all mice
    [    1.751306@2] usbcore: registered new interface driver xpad
    [    1.756652@0] i2c /dev entries driver
    [    1.761440@0] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
    [    1.765695@0] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
    [    1.776704@0] ff803000.serial: clock gate not found
    [    1.778161@0] meson_uart ff803000.serial: ==uart0 reg addr = ffffff800830d000
    [    1.785396@0] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 13, base_baud = 1500000) is a meson_uart
    [    1.800312@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200
    [    1.802998@0] console [ttyS0] enabled
    [    1.810233@0] bootconsole [aml_uart0] disabled
    [    1.819926@3] ff804000.serial: clock gate not found
    [    1.824072@3] meson_uart ff804000.serial: ==uart3 reg addr = ffffff8008321000
    [    1.831196@3] ff804000.serial: ttyS3 at MMIO 0xff804000 (irq = 14, base_baud = 1500000) is a meson_uart
    [    1.841518@0] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff8008323000
    [    1.847623@0] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 25, base_baud = 1500000) is a meson_uart
    [    1.857809@3] meson_uart ffd23000.serial: ==uart2 reg addr = ffffff8008325000
    [    1.864115@3] ffd23000.serial: ttyS2 at MMIO 0xffd23000 (irq = 26, base_baud = 1500000) is a meson_uart
    [    1.875156@1] amlogic-new-usb2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff8008348000
    [    1.884336@1] amlogic-new-usb3 ffe09080.usb3phy: This phy has no usb port
    [    1.890852@1] amlogic-new-usb3 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff800834c080
    [    1.905906@1] i2c i2c-1: of_i2c: modalias failure on /soc/aobus@ff800000/i2c@5000/mcu6350@40
    [    1.909677@1] i2c i2c-1: Failed to create I2C device for /soc/aobus@ff800000/i2c@5000/mcu6350@40
    [    1.922051@1] aml_dma ff63e000.aml_dma: Aml dma
    [    1.925190@1] aml_aes_dma ff63e000.aml_dma:aml_aes: Aml AES_dma
    [    1.930225@1] aml_sha_dma ff63e000.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma
    [    1.936534@1] efusekeynum: 4
    [    1.938858@1] efusekeyname:             mac	offset:     0	size:     6
    [    1.945304@1] efusekeyname:          mac_bt	offset:     6	size:     6
    [    1.951713@1] efusekeyname:        mac_wifi	offset:    12	size:     6
    [    1.958138@1] efusekeyname:            usid	offset:    18	size:    16
    [    1.964975@3] efuse efuse: probe OK!
    [    1.970386@3] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller
    [    1.977654@3] meson-mmc: >>>>>>>>hostbase ffffff8008358000, dmode 
    [    1.982762@3] meson-mmc: actual_clock :400000, HHI_nand: 0x80
    [    1.987934@3] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c
    [    2.031192@3] meson-mmc: meson_mmc_probe() : success!
    [    2.031447@3] amlogic mtd driver init
    [    2.035526@3] prase_get_dtb_nand_parameter:128,parse dts start
    [    2.040257@3] bl mode descrete
    [    2.043136@3] fip_copies 4
    [    2.045800@3] fip_size 0x200000
    [    2.048940@3] nand_clk_ctrl 0xffe07000
    [    2.052664@3] prase_get_dtb_nand_parameter:234,parse dts end
    [    2.058333@3] nand_clk_ctrl 0xffe07000
    [    2.062054@3] nand register base ffffff80083df800, nand clock register ffffff80083e1000
    [    2.070791@3] plat->aml_nand_device ffffff800a005a90
    [    2.074960@3] m3_nand_probe() aml_nand_device ffffff800a005a90
    [    2.081020@3] NAND device id: 98 da 90 15 76 16
    [    2.085261@3] NAND device: Manufacturer ID: 
    [    2.089327@3]  0x98, Chip ID: 0x98 (Toshiba A revision NAND 2Gib TC58NVG1S3HBAI4 )
    [    2.096890@3] oob_fill_cnt =32 oob_size =64, bch_bytes =14
    [    2.102323@3] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
    [    2.107872@3] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
    [    2.114116@3] mtd->oobavail: 0x8
    [    2.117519@3] aml_nand_init 2119: plat-name:bootloader
    [    2.122438@3] Creating 1 MTD partitions on "bootloader":
    [    2.127724@3] 0x000000000000-0x000000200000 : "bootloader"
    [    2.136852@0] bootloader initialized ok
    [    2.136984@0] plat->aml_nand_device ffffff800a005a90
    [    2.141960@0] m3_nand_probe() aml_nand_device ffffff800a005a90
    [    2.148105@0] NAND device id: 98 da 90 15 76 16
    [    2.152254@0] NAND device: Manufacturer ID: 
    [    2.156329@0]  0x98, Chip ID: 0x98 (Toshiba A revision NAND 2Gib TC58NVG1S3HBAI4 )
    [    2.163882@0] oob_fill_cnt =32 oob_size =64, bch_bytes =14
    [    2.169325@0] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
    [    2.174865@0] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
    [    2.181119@0] mtd->oobavail: 0x8
    [    2.184550@0] aml_nand_init 2119: plat-name:nandnormal
    [    2.189478@0] bbt_start=20
    [    2.192113@0] env_start=24
    [    2.194778@0] key_start=32
    [    2.197483@0] dtb_start=40
    [    2.200168@0] ddr_start=44
    [    2.202841@0] nbbt: info size=0x800 max_scan_blk=24, start_blk=20
    [    2.209379@0] get_free_node 43: bitmap=0
    [    2.212825@0] get_free_node 55: bitmap=1
    [    2.216931@0] get_free_node 43: bitmap=1
    [    2.220623@0] get_free_node 55: bitmap=3
    [    2.224730@0] get_free_node 43: bitmap=3
    [    2.228423@0] get_free_node 55: bitmap=7
    [    2.232324@0] nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1
    [    2.238994@0] nbbt free list:
    [    2.241943@0] blockN=21, ec=-1, dirty_flag=0
    [    2.246188@0] blockN=22, ec=-1, dirty_flag=0
    [    2.250433@0] blockN=23, ec=-1, dirty_flag=0
    [    2.254683@0] aml_nand_scan_rsv_info 1141: page_num=1
    [    2.260122@0] nbbt valid addr: 280000
    [    2.263361@0] aml_nand_bbt_check 1306 bbt is valid, reading.
    [    2.268985@0] aml_nand_read_rsv_info:423,read nbbt info at 280000
    [    2.275260@0] nenv: info size=0x10000 max_scan_blk=32, start_blk=24
    [    2.281497@0] get_free_node 43: bitmap=7
    [    2.285191@0] get_free_node 55: bitmap=f
    [    2.289500@0] get_free_node 43: bitmap=f
    [    2.292991@0] get_free_node 55: bitmap=1f
    [    2.297183@0] get_free_node 43: bitmap=1f
    [    2.300964@0] get_free_node 55: bitmap=3f
    [    2.305155@0] get_free_node 43: bitmap=3f
    [    2.308937@0] get_free_node 55: bitmap=7f
    [    2.313129@0] get_free_node 43: bitmap=7f
    [    2.316908@0] get_free_node 55: bitmap=ff
    [    2.321103@0] get_free_node 43: bitmap=ff
    [    2.324883@0] get_free_node 55: bitmap=1ff
    [    2.329163@0] get_free_node 43: bitmap=1ff
    [    2.333031@0] get_free_node 55: bitmap=3ff
    [    2.337104@0] nenv : phy_blk_addr=25, ec=0, phy_page_addr=0, timestamp=6
    [    2.343774@0] nenv free list:
    [    2.346705@0] blockN=24, ec=-1, dirty_flag=0
    [    2.350968@0] blockN=26, ec=-1, dirty_flag=0
    [    2.355215@0] blockN=27, ec=-1, dirty_flag=0
    [    2.359462@0] blockN=28, ec=-1, dirty_flag=0
    [    2.363708@0] blockN=29, ec=-1, dirty_flag=0
    [    2.367955@0] blockN=30, ec=-1, dirty_flag=0
    [    2.372202@0] blockN=31, ec=-1, dirty_flag=0
    [    2.376448@0] aml_nand_scan_rsv_info 1141: page_num=32
    [    2.394645@0] nenv valid addr: 330000
    [    2.394678@0] nkey: info size=0x8000 max_scan_blk=40, start_blk=32
    [    2.399068@0] get_free_node 43: bitmap=3ff
    [    2.402901@0] get_free_node 55: bitmap=7ff
    [    2.407214@0] get_free_node 43: bitmap=7ff
    [    2.411065@0] get_free_node 55: bitmap=fff
    [    2.415343@0] get_free_node 43: bitmap=fff
    [    2.419211@0] get_free_node 55: bitmap=1fff
    [    2.423577@0] get_free_node 43: bitmap=1fff
    [    2.427531@0] get_free_node 55: bitmap=3fff
    [    2.431898@0] get_free_node 43: bitmap=3fff
    [    2.435852@0] get_free_node 55: bitmap=7fff
    [    2.440218@0] get_free_node 43: bitmap=7fff
    [    2.444172@0] get_free_node 55: bitmap=ffff
    [    2.448537@0] get_free_node 43: bitmap=ffff
    [    2.452491@0] get_free_node 55: bitmap=1ffff
    [    2.456944@0] get_free_node 43: bitmap=1ffff
    [    2.460985@0] get_free_node 55: bitmap=3ffff
    [    2.465231@0] nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
    [    2.471902@0] nkey free list:
    [    2.474833@0] blockN=32, ec=-1, dirty_flag=0
    [    2.479096@0] blockN=33, ec=-1, dirty_flag=0
    [    2.483343@0] blockN=34, ec=-1, dirty_flag=0
    [    2.487590@0] blockN=35, ec=-1, dirty_flag=0
    [    2.491836@0] blockN=36, ec=-1, dirty_flag=0
    [    2.496082@0] blockN=37, ec=-1, dirty_flag=0
    [    2.500330@0] blockN=38, ec=-1, dirty_flag=0
    [    2.504576@0] blockN=39, ec=-1, dirty_flag=0
    [    2.508823@0] aml_nand_scan_rsv_info 1141: page_num=16
    [    2.513934@0] nkey valid addr: fffffffffffe0000
    [    2.518444@0] aml_nand_key_check 1251 NO key exist
    [    2.523218@0] ndtb: info size=0x20000 max_scan_blk=44, start_blk=40
    [    2.529658@0] get_free_node 43: bitmap=3ffff
    [    2.533698@0] get_free_node 55: bitmap=7ffff
    [    2.538353@0] get_free_node 43: bitmap=7ffff
    [    2.542191@0] get_free_node 55: bitmap=fffff
    [    2.546644@0] get_free_node 43: bitmap=fffff
    [    2.550685@0] get_free_node 55: bitmap=1fffff
    [    2.555018@0] ndtb : phy_blk_addr=41, ec=0, phy_page_addr=0, timestamp=2
    [    2.561689@0] ndtb free list:
    [    2.564636@0] blockN=40, ec=-1, dirty_flag=0
    [    2.568883@0] blockN=42, ec=-1, dirty_flag=0
    [    2.573130@0] blockN=43, ec=-1, dirty_flag=0
    [    2.577376@0] aml_nand_scan_rsv_info 1141: page_num=64
    [    2.595573@0] ndtb valid addr: 520000
    [    2.595606@0] nddr: info size=0x20000 max_scan_blk=46, start_blk=44
    [    2.600066@0] get_free_node 43: bitmap=1fffff
    [    2.604193@0] get_free_node 55: bitmap=3fffff
    [    2.608732@0] get_free_node 43: bitmap=3fffff
    [    2.612860@0] get_free_node 55: bitmap=7fffff
    [    2.617193@0] nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
    [    2.623863@0] nddr free list:
    [    2.626794@0] blockN=44, ec=-1, dirty_flag=0
    [    2.631058@0] blockN=45, ec=-1, dirty_flag=0
    [    2.635305@0] aml_nand_scan_rsv_info 1141: page_num=64
    [    2.640417@0] nddr valid addr: fffffffffffe0000
    [    2.644924@0] aml_nand_ddr_check 1281 NO ddr exist
    [    2.649695@0] tpl: off 8388608, size 8388608
    [    2.749287@0]  NAND bbt detect factory Bad block at c000000
    [    2.749337@0] aml_nand_add_partition:394 factory bad addr=600
    [    2.755016@0]  NAND bbt detect factory Bad block at c020000
    [    2.760525@0] aml_nand_add_partition:394 factory bad addr=601
    [    2.800770@0] Creating 6 MTD partitions on "nandnormal":
    [    2.800817@0] 0x000000800000-0x000001000000 : "tpl"
    [    2.812572@1] 0x000001000000-0x000001200000 : "misc"
    [    2.815944@2] 0x000001200000-0x000002200000 : "recovery"
    [    2.828135@1] 0x000002200000-0x000004200000 : "boot"
    [    2.847947@1] 0x000004200000-0x000004700000 : "config"
    [    2.852797@1] 0x000004700000-0x000010000000 : "nvdata"
    [    2.918817@1]  NAND bbt detect factory Bad block at c000000
    [    2.918935@1]  NAND bbt detect factory Bad block at c020000
    [    2.961394@0] nandnormal initialized ok
    [    2.961504@0] aml_ubootenv_init: register env chardev
    [    2.965291@0] aml_ubootenv_init: register env chardev OK
    [    2.970079@0] amlnf_dtb_init: register dtb cdev
    [    2.975078@0] amlnf_dtb_init: register dtd cdev OK
    [    2.979234@0] mtd_nand_probe 267 , err = 0
    [    2.984489@3] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc0
    [    2.989843@3] input: aml_vkeypad as /devices/platform/rtc/input/input0
    [    2.996849@0] unifykey: storage in base: 0xffffffc005000000
    [    3.001430@0] unifykey: storage out base: 0xffffffc005040000
    [    3.007094@0] unifykey: storage block base: 0xffffffc005080000
    [    3.012833@0] unifykey: probe done!
    [    3.017031@0] unifykey: no efuse-version set, use default value: -1
    [    3.022556@0] unifykey: key unify config unifykey-num is 6
    [    3.028075@0] unifykey: key unify fact unifykey-num is 6
    [    3.033305@0] unifykey: unifykey_devno: f200000
    [    3.038290@2] unifykey: device unifykeys created ok
    [    3.042799@2] unifykey: aml_unifykeys_init done!
    [    3.047728@2] sysled: module init
    [    3.051156@2] meson_wdt ffd0f0d0.watchdog: start watchdog
    [    3.055924@2] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog
    [    3.063519@2] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done
    [    3.072129@3] dmc_monitor_probe
    [    3.072926@3] page_trace_module_init, create sysfs failed
    [    3.078801@3] defendkey defendkey: Reserved memory is not enough!
    [    3.084060@3] defendkey: probe of defendkey failed with error -22
    [    3.090378@3] GACT probability NOT on
    [    3.093734@3] Mirror/redirect action on
    [    3.097524@3] u32 classifier
    [    3.100368@3]     Actions configured
    [    3.103928@3] Netfilter messages via NETLINK v0.30.
    [    3.109213@3] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
    [    3.115452@3] ctnetlink v0.93: registering with nfnetlink.
    [    3.121283@3] xt_time: kernel timezone is -0000
    [    3.125030@3] ipip: IPv4 and MPLS over IPv4 tunneling driver
    [    3.131712@3] ip_tables: (C) 2000-2006 Netfilter Core Team
    [    3.136367@3] arp_tables: arp_tables: (C) 2002 David S. Miller
    [    3.141806@3] Initializing XFRM netlink socket
    [    3.147440@3] NET: Registered protocol family 10
    [    3.153306@3] mip6: Mobile IPv6
    [    3.153873@3] ip6_tables: (C) 2000-2006 Netfilter Core Team
    [    3.159874@3] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
    [    3.167961@3] NET: Registered protocol family 17
    [    3.170082@3] NET: Registered protocol family 15
    [    3.174744@3] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
    [    3.187870@3] l2tp_core: L2TP core driver, V2.0
    [    3.192262@3] l2tp_ppp: PPPoL2TP kernel driver, V2.0
    [    3.197178@3] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
    [    3.202927@3] l2tp_netlink: L2TP netlink interface
    [    3.207759@3] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
    [    3.213805@3] l2tp_debugfs: L2TP debugfs support
    [    3.218341@3] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
    [    3.224987@3] NET: Registered protocol family 35
    [    3.229925@3] Key type dns_resolver registered
    [    3.234460@3] Registered swp emulation handler
    [    3.238363@3] Registered cp15_barrier emulation handler
    [    3.243564@3] Registered setend emulation handler
    [    3.248296@3] disable EAS feature
    [    3.253132@0] registered taskstats version 1
    [    3.270063@0] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host
    [    3.776522@0] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
    [    3.776613@0] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
    [    3.784903@0] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f664 hci version 0x100 quirks 0x02010010
    [    3.793345@0] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0xff500000
    [    3.800860@3] hub 1-0:1.0: USB hub found
    [    3.803290@3] hub 1-0:1.0: 1 port detected
    [    3.807915@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
    [    3.812916@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
    [    3.820829@3] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
    [    3.830312@0] hub 2-0:1.0: USB hub found
    [    3.832914@0] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
    [    3.840195@0] usb usb2: Unsupported the hub
    [    3.844991@0] aml_vrtc rtc: setting system clock to 2015-01-01 00:00:09 UTC (1420070409)
    [    3.853042@0] dwc_otg ff400000.dwc2_a: dwc_otg_driver_probe(ffffffc00e183800)
    [    3.853118@0] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0
    [    3.861009@0] dwc_otg ff400000.dwc2_a: base=0xffffff8008580000
    [    3.861021@0] dwc_otg ff400000.dwc2_a: dwc_otg_device=0xffffffc00c239400
    [    3.961585@0] dwc_otg: Core Release: 3.10a
    [    3.961657@0] dwc_otg: Setting default values for core params
    [    3.965830@0] dwc_otg: curmode: 0, host_only: 0
    [    3.970334@0] dwc_otg ff400000.dwc2_a: DMA config: BURST_DEFAULT
    [    3.982869@0] dwc_otg: Using Buffer DMA mode
    [    3.982907@0] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
    [    3.986813@0] dwc_otg: Working on port type = SLAVE
    [    3.991670@0] dwc_otg: Dedicated Tx FIFOs mode
    [    3.998658@0] thermal thermal_zone0: binding zone soc_thermal with cdev thermal-cpufreq-0 failed:-22
    [    4.005393@0] cpucore_cooling_register, max_cpu_core_num:4
    [    4.018039@0] gxbb_pm: enter meson_pm_probe!
    [    4.018096@0] no vddio3v3_en pin
    [    4.019792@0] pm-meson aml_pm: Can't get switch_clk81
    [    4.024830@0] gxbb_pm: meson_pm_probe done
    [    4.029768@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
    [    4.036162@0] Freeing unused kernel memory: 3648K
    [    4.051321@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
    [    4.309375@3] ubi0: attaching mtd5
    [    4.320947@3] ubi0: scanning is finished
    [    4.320996@3] ubi0: empty MTD device detected
    [    4.338179@2] ubi0: attached mtd5 (name "config", size 5 MiB)
    [    4.338307@2] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
    [    4.345378@2] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
    [    4.352273@2] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
    [    4.359386@2] ubi0: good PEBs: 40, bad PEBs: 0, corrupted PEBs: 0
    [    4.365446@2] ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
    [    4.372822@2] ubi0: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 686225878
    [    4.381996@2] ubi0: available PEBs: 32, total reserved PEBs: 8, PEBs reserved for bad PEB handling: 4
    [    4.391216@3] ubi0: background thread "ubi_bgt0d" started, PID 1075
    [    4.441229@1] UBIFS (ubi0:0): default file-system created
    [    4.443685@0] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 1081
    [    4.488822@1] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "config_data"
    [    4.491234@1] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
    [    4.501270@1] UBIFS (ubi0:0): FS size: 2793472 bytes (2 MiB, 22 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
    [    4.511491@1] UBIFS (ubi0:0): reserved for root: 131942 bytes (128 KiB)
    [    4.518081@1] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 2A8C614D-579F-45DE-95D3-CA57BF000942, small LPT model
    [    4.542687@2] ubi2: attaching mtd6
    [    4.811670@2]  NAND bbt detect factory Bad block at c000000
    [    4.811796@2]  NAND bbt detect factory Bad block at c020000
    [    4.958613@2] ubi2: scanning is finished
    [    4.958652@2] ubi2: empty MTD device detected
    [    4.980251@3] ubi2: attached mtd6 (name "nvdata", size 185 MiB)
    [    4.980559@3] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
    [    4.987675@3] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
    [    4.994539@3] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096
    [    5.001630@3] ubi2: good PEBs: 1478, bad PEBs: 2, corrupted PEBs: 0
    [    5.007876@3] ubi2: user volume: 0, internal volumes: 1, max. volumes count: 128
    [    5.015236@3] ubi2: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 259925530
    [    5.024429@3] ubi2: available PEBs: 1472, total reserved PEBs: 6, PEBs reserved for bad PEB handling: 2
    [    5.033827@1] ubi2: background thread "ubi_bgt2d" started, PID 1087
    [    5.088305@3] UBIFS (ubi2:0): default file-system created
    [    5.090767@2] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 1094
    [    5.138225@3] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "nvdata_data"
    [    5.140650@3] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
    [    5.150687@3] UBIFS (ubi2:0): FS size: 185384960 bytes (176 MiB, 1460 LEBs), journal size 9269248 bytes (8 MiB, 73 LEBs)
    [    5.161513@3] UBIFS (ubi2:0): reserved for root: 4952683 bytes (4836 KiB)
    [    5.168368@3] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID 48A345E1-7069-4F38-A5B9-2A7FB882E917, small LPT model
    [    5.502097@0] eth0: device MAC address 02:23:8d:e6:c8:58
    [    5.583817@2] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP.
    [    5.585141@2] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    [    5.806674@2] uart_trans: loading out-of-tree module taints kernel.
    [    5.809269@2] register uart_trans chrdev success.
    [    5.812466@2] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 0 to 9600
    [    5.820041@2] tty port open success [/dev/ttyS3]!
    [    5.824868@2] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 9600 to 115200
    [    5.833098@2] init sucess for tty struct (246:3)  [/dev/ttyS3]
    [    5.839298@2] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 0 to 9600
    [    5.846891@2] tty port open success [/dev/ttyS2]!
    [    5.851551@2] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 9600 to 115200
    [    5.859965@2] init sucess for tty struct (246:2)  [/dev/ttyS2]
    [    5.866057@2] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 0 to 9600
    [    5.873742@2] tty port open success [/dev/ttyS1]!
    [    5.878415@2] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 115200
    [    5.886819@2] init sucess for tty struct (246:1)  [/dev/ttyS1]
    [    5.893104@2] create workqueue success!
    [    7.623396@2] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
    [    7.626507@2] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    
    
    ===========================================Miner log===========================================
    2015-01-01 00:00:16 Miner compile time: Fri Nov 19 22:11:07 CST 2021 type: Antminer S19j Pro
    2015-01-01 00:00:17 This is fix-freq version
    2015-01-01 00:00:17 Miner compile time: Fri Nov 19 22:11:07 CST 2021 type: Antminer S19j Pro
    2015-01-01 00:00:17 commit version: ce69be1 2021-10-19 19:57:55, build by: jenkins 2021-11-19 22:23:40
    2015-01-01 00:00:17 opt_multi_version     = 1
    2015-01-01 00:00:17 opt_bitmain_ab        = 1
    2015-01-01 00:00:17 mid_auto_gen          = 1
    2015-01-01 00:00:17 opt_bitmain_work_mode = 0
    2015-01-01 00:00:17 port 439 already exported
    2015-01-01 00:00:17 port 454 already exported
    2015-01-01 00:00:17 port 440 already exported
    2015-01-01 00:00:17 port 455 already exported
    2015-01-01 00:00:17 port 441 already exported
    2015-01-01 00:00:17 port 456 already exported
    2015-01-01 00:00:17 port 438 already exported
    2015-01-01 00:00:17 port 453 already exported
    2015-01-01 00:00:17 port 446 already exported
    2015-01-01 00:00:17 port 445 already exported
    2015-01-01 00:00:17 Note: front fan is power on!
    2015-01-01 00:00:17 Note: rear fan is power on!
    2015-01-01 00:00:17 start the http log.
    2015-01-01 00:00:17 httpListenThread start ret=0
    2015-01-01 00:00:17 start listen on 6060 ...
    2015-01-01 00:00:17 load machine BHB42601 conf
    2015-01-01 00:00:17 machine : BHB42601 
    2015-01-01 00:00:17 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
    2015-01-01 00:00:17 bad chain id = 3
    2015-01-01 00:00:20 bad chain id = 3
    2015-01-01 00:00:22 ==========================capability start==========================
    2015-01-01 00:00:22 board num = 3
    2015-01-01 00:00:22 board id = 0, chain num = 1
    2015-01-01 00:00:22 	chain id = 0
    2015-01-01 00:00:22 board id = 1, chain num = 1
    2015-01-01 00:00:22 	chain id = 1
    2015-01-01 00:00:22 board id = 2, chain num = 1
    2015-01-01 00:00:22 	chain id = 2
    2015-01-01 00:00:22 ==========================capability end============================
    2015-01-01 00:00:22 chain num = 3
    2015-01-01 00:00:23 load chain 0 eeprom data
    2015-01-01 00:00:23 FW type BHB42601, eeprom[0] shows BHB42631
    2015-01-01 00:00:24 load chain 1 eeprom data
    2015-01-01 00:00:24 FW type BHB42601, eeprom[1] shows BHB42631
    2015-01-01 00:00:24 load chain 2 eeprom data
    2015-01-01 00:00:24 FW type BHB42601, eeprom[2] shows BHB42631
    2015-01-01 00:00:24 Sweep error string = J7:4.
    2015-01-01 00:00:24 Fixture data load failed, exit.
    2015-01-01 00:00:24 ERROR_SOC_INIT: basic init failed!
    2015-01-01 00:00:24 stop_mining: basic init failed!
    2015-01-01 00:00:24 ****power off hashboard****
    2015-01-01 00:00:25 fail to write 0:7
    2015-01-01 00:00:25 fail to write 1:7
    2015-01-01 00:00:25 fail to write 2:7
    2015-01-01 00:00:25 fail to write 3:7
    2015-01-01 00:00:25 fail to write 4:7
    2015-01-01 00:00:25 fail to write 5:7
    2015-01-01 00:00:25 fail to write 6:7
    2015-01-01 00:00:25 fail to read 0:2
    2015-01-01 00:00:25 fail to read 1:2
    2015-01-01 00:00:25 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0x00, read_back_data[1] = 0x00
    2015-01-01 00:00:25 fail to write 0:7
    2015-01-01 00:00:25 fail to write 1:7
    2015-01-01 00:00:25 fail to write 2:7
    2015-01-01 00:00:25 fail to write 3:7
    2015-01-01 00:00:25 fail to write 4:7
    2015-01-01 00:00:25 fail to write 5:7
    2015-01-01 00:00:25 fail to write 6:7
    2015-01-01 00:00:26 fail to read 0:2
    2015-01-01 00:00:26 fail to read 1:2
    2015-01-01 00:00:26 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0x00, read_back_data[1] = 0x00
    2015-01-01 00:00:26 fail to write 0:7
    2015-01-01 00:00:26 fail to write 1:7
    2015-01-01 00:00:26 fail to write 2:7
    2015-01-01 00:00:26 fail to write 3:7
    2015-01-01 00:00:26 fail to write 4:7
    2015-01-01 00:00:26 fail to write 5:7
    2015-01-01 00:00:26 fail to write 6:7
    2015-01-01 00:00:26 fail to read 0:2
    2015-01-01 00:00:26 fail to read 1:2
    2015-01-01 00:00:26 _bitmain_pic_disable_dc_dc_common failed! read_back_data[0] = 0x00, read_back_data[1] = 0x00
    2022-12-03 01:45:51 reload pool, need recalculate
    2022-12-03 01:45:51 set_start_time_point total_tv_start_sys=196 total_tv_end_sys=197
    0
    Comment actions Permalink

Please sign in to leave a comment.