New S19 Pro - missing hash board - next steps?

Official comment

Nick

July 06, 2021 05:18

Dear

For the hashboard which can not be detected ,please try to exclude the issues by the below instructions

1.check the wires for the hashboard--pull them and re-plug them again, and also you can try to change the new wires
2.upgrade to the latest firmware
3. change the PSU to try it and reset the miner to the factory settings
4.flash the SD card program to recover the control board
Please download the SD card file in the below link

https://service.bitmain.com/support/download?product=Flashing%20SD%20card%20with%20image

instructions:

https://support.bitmain.com/hc/en-us/articles/900003100743-S19-S19-Pro-control-board-program-recovery-SD-card-flashing-

Jay Pierson

July 06, 2021 23:30

Thank you for following up. I've performed the following steps and still have the same issue.

1. Re-seated all cables from control board to the hash boards (no change)

2. swapped only the hash board side of 2 cables (left plugged into the same place on the control board while swapping hash board 2 and 3. This moved the dead hash board from #2 to #3)

3. Updated to the most recent firmware and performed a reset (no change)

4. Flashed the control board with image (no change)

5. swapped psu with another s19 pro (no change)

Please let me know how to proceed. Thank you

2021-07-06 23:23:50 Chain[0]: find 114 asic, times 0
2021-07-06 23:23:57 Chain[1]: find 0 asic, times 0
2021-07-06 23:24:05 Chain[1]: find 0 asic, times 1
2021-07-06 23:24:13 Chain[1]: find 0 asic, times 2
2021-07-06 23:24:14 Chain 1 only find 0 asic, will power off hash board 1
2021-07-06 23:24:22 Chain[2]: find 114 asic, times 0

0

Nick

July 07, 2021 06:11

Dear

If still can not fix it ,the hashboard should has the faulty , could you send it back to the Hongkong or the USA-NH repair site for repair based on the below instructions.

We are sorry that your miner is defective , please unplug then reboot it again, if it still can not work please refer to this link to prepare to ship the miner or part to us :https://service.bitmain.com/support/guide

Please check this link to create a repair ticket, please always click " apply for repair " to send the defective unit/part to us to have a repair.

How to create/revise a repair ticket

Pls send the defective miner to our official repair site(HK or US site), the address is as following link: https://support.bitmain.com/hc/en-us/articles/220138027-Global-repair-site-delivery-addresses

Pls let us know if you have any problems. Thanks.

0

Aden Putra

December 18, 2021 02:35

I have the same issue, but the miner still on the warranty.. does sending the hashboard can void the warranty? and can i get a fast response on my email?

my email is : adnputra3@gmail.com

This is my full kernel log, anyone can help with this?

free_area_init_node: node 0, pgdat c0b3c040, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf0000 s19916 r8192 d21044 u49152
pcpu-alloc: s19916 r8192 d21044 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 209652K/245760K available (6317K kernel code, 243K rwdata, 1932K rodata, 1024K init, 232K bss, 19724K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090e410 (9242 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b3cda0 ( 244 kB)
.bss : 0xc0b3cda0 - 0xc0b77024 ( 233 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 6652K (cd47b000 - cdafa000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 159, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
cdns-i2c e0005000.ps7_i2c: 100 kHz mmio e0005000 irq 154
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: disable subpage write
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: NAND_ECC_HW
nand: NAND_ECC_HW_SYNDROME
mtd->writesize = 2048
ecc->strength = 1
ecc->size = 2048
mtd->writesize = 2048
chip->ecc_strength_ds = 4
chip->ecc_step_ds = 512
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
8 ofpart partitions found on MTD device pl35x-nand
Creating 8 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-dts-marker-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000005200000 : "sig"
0x000005200000-0x000006000000 : "reserve1"
0x000006000000-0x000007000000 : "upgrade-ramfs"
0x000007000000-0x00000a800000 : "upgrade-file"
0x00000a800000-0x000010000000 : "reserve2"
nf_conntrack version 0.5.0 (3635 buckets, 14540 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs warning (device ram0): ext4_update_dynamic_rev:746: updating to rev 1 because of new feature flag, running e2fsck is recommended
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr,errors=remount-ro
devpts: called with bogus options
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 20648290
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 4
ubi0: background thread "ubi_bgt0d" started, PID 729
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 733
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "config_data"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 5840896 bytes (5 MiB, 46 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
UBIFS (ubi0:0): reserved for root: 275879 bytes (269 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 21CB1460-7FA9-47B9-BC68-F96BF0F8A768, small LPT model
ubi2: attaching mtd4
ubi2: scanning is finished
ubi2: attached mtd4 (name "reserve1", size 14 MiB)
ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi2: good PEBs: 112, bad PEBs: 0, corrupted PEBs: 0
ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi2: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 897156384
ubi2: available PEBs: 0, total reserved PEBs: 112, PEBs reserved for bad PEB handling: 4
ubi2: background thread "ubi_bgt2d" started, PID 740
UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 744
UBIFS (ubi2:0): recovery needed
UBIFS (ubi2:0): recovery completed
UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "misc"
UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi2:0): FS size: 11935744 bytes (11 MiB, 94 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
UBIFS (ubi2:0): reserved for root: 563754 bytes (550 KiB)
UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID 75633C3D-1D2C-40CB-BE7A-20A00B52F1D8, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
random: avahi-daemon urandom read with 2 bits of entropy available
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfbc8000
*base_vir_addr = 0xb031
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized

===========================================Miner log===========================================
1970-01-01 00:00:09 Invalid config option --bitmain-freq: '' is not a number
1970-01-01 00:00:09 Invalid config option --bitmain-voltage: '' is not a number
1970-01-01 00:00:09 Invalid config option --bitmain-ccdelay: '' is not a number
1970-01-01 00:00:09 Invalid config option --bitmain-pwth: '' is not a number
1970-01-01 00:00:09 Miner compile time: Tue Nov 16 19:20:40 CST 2021 type: Antminer S19 Pro
1970-01-01 00:00:10 This is fix-freq version
1970-01-01 00:00:10 Miner compile time: Tue Nov 16 19:20:40 CST 2021 type: Antminer S19 Pro
1970-01-01 00:00:10 commit version: 386747fa 2021-10-21 19:58:45, build by: jenkins 2021-11-16 19:37:57
1970-01-01 00:00:10 opt_multi_version = 1
1970-01-01 00:00:10 opt_bitmain_ab = 1
1970-01-01 00:00:10 mid_auto_gen = 0
1970-01-01 00:00:10 opt_bitmain_work_mode = 0
1970-01-01 00:00:10 mmap fpga_mem_addr_hal = 0xb5800000
1970-01-01 00:00:10 HASH_ON_PLUG V9 = 0x7
1970-01-01 00:00:10 Note: front fan is power on!
1970-01-01 00:00:10 Note: rear fan is power on!
1970-01-01 00:00:10 start the http log.
1970-01-01 00:00:10 httpListenThread start ret=0
1970-01-01 00:00:10 start listen on 6060 ...
1970-01-01 00:00:10 load machine NBP1901 conf
1970-01-01 00:00:10 machine : NBP1901
1970-01-01 00:00:10 chain_num 4, chain_domain_num 38, chain_asic_num 114, domain_asic_num 3
2021-12-17 15:41:46 miner ID : 800cd44a5cfaa854
2021-12-17 15:41:46 FPGA Version = 0xB031
2021-12-17 15:41:46 HASH_ON_PLUG V9 = 0x7
2021-12-17 15:41:46 ==========================capability start==========================
2021-12-17 15:41:46 board num = 3
2021-12-17 15:41:46 board id = 0, chain num = 1
2021-12-17 15:41:46 chain id = 0
2021-12-17 15:41:46 board id = 1, chain num = 1
2021-12-17 15:41:46 chain id = 1
2021-12-17 15:41:46 board id = 2, chain num = 1
2021-12-17 15:41:46 chain id = 2
2021-12-17 15:41:46 ==========================capability end============================
2021-12-17 15:41:46 chain num = 3
2021-12-17 15:41:48 [chain 0]
2021-12-17 15:41:48 0x0000 11 4A D7 7A 3B FB 75 72 CE 56 17 95 94 9C 9E BC
2021-12-17 15:41:48 0x0010 E8 F3 6F 1B EF 75 C3 8B 08 28 2E BC EA A8 25 70
2021-12-17 15:41:48 0x0020 39 33 00 04 76 B5 0D 8F FF FA 39 38 17 11 01 0D
2021-12-17 15:41:48 0x0030 08 C7 D2 FF C3 CC 14 1B FE 53 68 08 E9 BD E4 48
2021-12-17 15:41:48 0x0040 A8 E6 E3 FC 46 2D 94 B8 BC 15 FF FF FF FF FF FF
2021-12-17 15:41:48 0x0050 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:48 0x0060 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:48 0x0070 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:48 0x0080 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:48 0x0090 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:48 0x00A0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:48 0x00B0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:48 0x00C0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:48 0x00D0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:48 0x00E0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:48 0x00F0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 5A
2021-12-17 15:41:48
2021-12-17 15:41:50 [chain 1]
2021-12-17 15:41:50 0x0000 11 4A 6D 94 44 E8 65 5D 88 62 85 EE 33 DC 7A E7
2021-12-17 15:41:50 0x0010 B0 CA 1F 03 C1 FA A6 FA 37 3F 89 86 0B 8F 8D 2C
2021-12-17 15:41:50 0x0020 2E 20 3D 69 BE 9E D0 10 65 73 5B FE CB D6 6D 20
2021-12-17 15:41:50 0x0030 12 AF 6B B1 FD 86 46 2C D3 A3 E7 0F 45 13 A5 EE
2021-12-17 15:41:50 0x0040 FC 94 4F 7C D0 7F EE 24 A1 29 FF FF FF FF FF FF
2021-12-17 15:41:50 0x0050 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:50 0x0060 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:50 0x0070 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:50 0x0080 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:50 0x0090 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:50 0x00A0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:50 0x00B0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:50 0x00C0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:50 0x00D0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:50 0x00E0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:50 0x00F0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 5A
2021-12-17 15:41:50
2021-12-17 15:41:52 [chain 2]
2021-12-17 15:41:52 0x0000 11 4A 6E F2 45 83 74 79 3E FE 63 4D 34 92 73 62
2021-12-17 15:41:52 0x0010 47 37 CC 87 E7 92 E2 C3 BF 1A 20 F6 F3 B3 9B 75
2021-12-17 15:41:52 0x0020 F6 55 8D 59 8E 18 68 D5 BB 29 98 F7 57 A3 BA 5A
2021-12-17 15:41:52 0x0030 DB 69 84 70 F7 E5 A5 35 E2 EE 17 FF 95 A1 1A 5B
2021-12-17 15:41:52 0x0040 89 7C CD C9 F1 6E 81 70 B9 E5 FF FF FF FF FF FF
2021-12-17 15:41:52 0x0050 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:52 0x0060 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:52 0x0070 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:52 0x0080 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:52 0x0090 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:52 0x00A0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:52 0x00B0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:52 0x00C0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:52 0x00D0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:52 0x00E0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
2021-12-17 15:41:52 0x00F0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 5A
2021-12-17 15:41:52
2021-12-17 15:41:52 fan_eft : 1 fan_pwm : 100
2021-12-17 15:41:52 create thread
2021-12-17 15:41:52 fixed working voltage = 1260
2021-12-17 15:41:52 Chain [0] PCB Version: 0x011e
2021-12-17 15:41:52 Chain [0] BOM Version: 0x0100
2021-12-17 15:41:52 Chain [1] PCB Version: 0x011e
2021-12-17 15:41:52 Chain [1] BOM Version: 0x0100
2021-12-17 15:41:52 Chain [2] PCB Version: 0x011e
2021-12-17 15:41:52 Chain [2] BOM Version: 0x0100
2021-12-17 15:41:56 Fan check passed.
2021-12-17 15:41:57 chain[0] PIC jump to app
2021-12-17 15:41:58 Check chain[0] PIC fw version=0x89
2021-12-17 15:41:59 chain[1] PIC jump to app
2021-12-17 15:42:01 Check chain[1] PIC fw version=0x89
2021-12-17 15:42:02 chain[2] PIC jump to app
2021-12-17 15:42:04 Check chain[2] PIC fw version=0x89
2021-12-17 15:42:04 create thread
2021-12-17 15:42:04 max sensor num = 4
2021-12-17 15:42:04 temperature_monitor_thread start...
2021-12-17 15:42:08 power type version: 0x0071
2021-12-17 15:42:08 Enter sleep to make sure power release finish.
2021-12-17 15:42:57 Slept 48 seconds, diff = 5.
2021-12-17 15:42:57 set_voltage_by_steps to 1500.
2021-12-17 15:43:02 chain avg vol rise to 15.32
2021-12-17 15:43:03 start up min temp by 75a = 29
2021-12-17 15:43:03 set UART baud to 115200
2021-12-17 15:43:11 Chain[0]: find 0 asic, times 0
2021-12-17 15:43:19 Chain[0]: find 0 asic, times 1
2021-12-17 15:43:27 Chain[0]: find 0 asic, times 2
2021-12-17 15:43:27 Chain 0 only find 0 asic, will power off hash board 0
2021-12-17 15:43:29 chain avg vol rise to 22.97
2021-12-17 15:43:36 Chain[1]: find 114 asic, times 0
2021-12-17 15:43:41 chain avg vol drop to 15.28
2021-12-17 15:43:43 Chain[2]: find 114 asic, times 0
2021-12-17 15:43:43 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 0
2021-12-17 15:43:46 min freq in eeprom = 525
2021-12-17 15:43:46 fixed frequency is 525
2021-12-17 15:43:46 Bring up temperature is 29
2021-12-17 15:43:47 set UART baud to 12000000
2021-12-17 15:43:47 set_voltage_by_steps to 1260.
2021-12-17 15:43:54 STATUS_INITED: soc init done!
2021-12-17 15:43:54 create thread
2021-12-17 15:43:54 create thread
2021-12-17 15:43:55 fan_etf: Set fixed fan speed=100
2021-12-17 15:44:02 start to init...
2021-12-17 15:44:10 Init done!
2021-12-17 15:44:10 STATUS_OKAY
2021-12-17 15:44:10 start the cached job
2021-12-17 15:44:10 Version num 8
2021-12-17 15:44:10 Mask num 0xe000
2021-12-17 15:44:10 freq = 525, percent = 90, hcn = 12480, timeout = 449
2021-12-17 15:44:10 set_start_time_point total_tv_start_sys=161 total_tv_end_sys=162

0

Linda

December 20, 2021 08:46

Hello, any problem please contact us at support-cs@bitmain.com to provide completed kernel log.

0

New S19 Pro - missing hash board - next steps?

Comments

Didn't find what you were looking for?