Antminer S19j Pro not mining

March 20, 2024 11:05

Dear Mr/Mrs ,

I am having the same as before problem with one of my miners .

I have Antminers S19j pro for about 2 years .

Last year I had emperature chip sensor problem with one of the hashboards and I send it back to you for repair . Its been 3-4 months and now I have the same problem , this time on the other miner .

The error was OVER_MAX_TEMP . I started to remove one by one the hashboards to see which one is not working . I found the faulty one (which I can send it to you for repair) but now the miner with the other two hashboards is mining with about 24-30T hashrate , which is very low and I cannot understand why ?

When I had the same problem before when I send one of the hashboards to you for repair , my miner was mining 70-80T hashrate with 2 hashboards . Now I cannot understand why the other one is mining only with 24-30T hashrate .

I am sending kernel log to see if there is another problem :

023-11-15 20:51:20 start do_core_reset
2023-11-15 20:51:39 end do_core_reset
2023-11-15 20:51:49 set_voltage_by_steps to 1376.
2023-11-15 20:51:51 Init done!
2023-11-15 20:51:51 STATUS_OKAY
2023-11-15 20:51:51 start the cached job
2023-11-15 20:51:51 Version num 65536
2023-11-15 20:51:51 Mask num 0x1fffe000
2023-11-15 20:51:51 opt_multi_version = 65536, interval timeout = 2837042
2023-11-15 20:51:51 freq = 545, percent = 90, hcn = 4809, timeout = 2837042
2023-11-15 20:51:51 set_start_time_point total_tv_start_sys=374918 total_tv_end_sys=374919
2023-11-15 20:52:53 set_voltage_by_steps to 1366.
2023-11-15 20:56:53 WARN_NET_LOST: network connection lost
2023-11-15 20:56:53 will power off in 169 seconds in case not resume
2023-11-15 20:58:05 bitmain_c5_scanhash: job_id non't found ...
2023-11-15 20:58:05 bitmain_c5_scanhash: job_id non't found ...
2023-11-15 20:58:05 bitmain_c5_scanhash: job_id non't found ...
2023-11-15 20:58:05 bitmain_c5_scanhash: job_id non't found ...
2023-11-15 20:58:05 bitmain_c5_scanhash: job_id non't found ...
2023-11-15 20:58:05 network connection resume
2023-11-15 20:58:05 STATUS_OKAY
2023-11-15 21:20:36 30m avg rate is 106208.36 in 28 mins
2023-11-15 21:50:39 30m avg rate is 106115.37 in 30 mins
2023-11-15 22:20:42 30m avg rate is 106122.08 in 30 mins
2023-11-15 22:50:46 30m avg rate is 106029.39 in 30 mins
2023-11-15 23:20:49 30m avg rate is 105904.37 in 30 mins
2023-11-15 23:50:52 30m avg rate is 105897.67 in 30 mins
2023-11-16 00:20:55 30m avg rate is 105923.68 in 30 mins
2023-11-16 00:50:58 30m avg rate is 105320.77 in 30 mins
2023-11-16 01:21:01 30m avg rate is 105494.57 in 30 mins
2023-11-16 01:51:04 30m avg rate is 106117.20 in 30 mins
2023-11-16 02:21:08 30m avg rate is 106115.98 in 30 mins
2023-11-16 02:51:11 30m avg rate is 106053.78 in 30 mins
2023-11-16 03:21:14 30m avg rate is 105875.71 in 30 mins
2023-11-16 03:51:17 30m avg rate is 105624.43 in 30 mins
2023-11-16 04:21:20 30m avg rate is 105644.59 in 30 mins
2023-11-16 04:51:23 30m avg rate is 105858.03 in 30 mins
2023-11-16 05:21:27 30m avg rate is 105918.40 in 30 mins
2023-11-16 05:51:30 30m avg rate is 105734.84 in 30 mins
2023-11-16 06:21:33 30m avg rate is 105970.24 in 30 mins
2023-11-16 06:51:36 30m avg rate is 105564.09 in 30 mins
2023-11-16 07:21:39 30m avg rate is 105691.55 in 30 mins
2023-11-16 07:51:42 30m avg rate is 105912.30 in 30 mins
2023-11-16 08:21:45 30m avg rate is 105760.46 in 30 mins
2023-11-16 08:51:49 30m avg rate is 105743.38 in 30 mins
2023-11-16 09:21:52 30m avg rate is 105709.84 in 30 mins
2023-11-16 09:51:55 30m avg rate is 105576.29 in 30 mins
2023-11-16 10:21:58 30m avg rate is 106142.49 in 30 mins
2023-11-16 10:52:01 30m avg rate is 105903.15 in 30 mins
2023-11-16 11:22:04 30m avg rate is 105644.59 in 30 mins
2023-11-16 11:52:08 30m avg rate is 105650.08 in 30 mins
2023-11-16 12:22:11 30m avg rate is 105343.95 in 30 mins
2023-11-16 12:52:14 30m avg rate is 105955.60 in 30 mins
2023-11-16 13:22:17 30m avg rate is 106242.44 in 30 mins
2023-11-16 13:52:20 30m avg rate is 105825.10 in 30 mins
2023-11-16 14:22:23 30m avg rate is 105914.74 in 30 mins
2023-11-16 14:52:26 30m avg rate is 105797.66 in 30 mins
2023-11-16 15:22:30 30m avg rate is 105620.20 in 30 mins
2023-11-16 15:52:33 30m avg rate is 105978.16 in 30 mins
2023-11-16 16:22:36 30m avg rate is 105525.67 in 30 mins
2023-11-16 16:52:39 30m avg rate is 105626.25 in 30 mins
2023-11-16 17:22:42 30m avg rate is 105413.47 in 30 mins
2023-11-16 17:52:45 30m avg rate is 105649.47 in 30 mins
2023-11-16 18:22:49 30m avg rate is 105716.55 in 30 mins
2023-11-16 18:52:52 30m avg rate is 106178.19 in 30 mins
2023-11-16 19:22:55 30m avg rate is 105844.00 in 30 mins
2023-11-16 19:52:58 30m avg rate is 105619.55 in 30 mins
2023-11-16 20:23:01 30m avg rate is 105705.57 in 30 mins
2023-11-16 20:53:04 30m avg rate is 105890.96 in 30 mins
2023-11-16 21:23:07 30m avg rate is 106039.15 in 30 mins
2023-11-16 21:53:11 30m avg rate is 105889.13 in 30 mins
2023-11-16 22:09:54 set_voltage_by_steps to 1376.
2023-11-16 22:23:14 30m avg rate is 106030.00 in 30 mins
2023-11-16 22:53:17 30m avg rate is 106044.02 in 30 mins
2023-11-16 23:23:20 30m avg rate is 105486.68 in 30 mins
2023-11-16 23:53:23 30m avg rate is 105889.74 in 30 mins
2023-11-17 00:23:26 30m avg rate is 106047.07 in 30 mins
2023-11-17 00:53:29 30m avg rate is 105634.83 in 30 mins
2023-11-17 01:23:33 30m avg rate is 105837.90 in 30 mins
2023-11-17 01:30:26 set_voltage_by_steps to 1366.
2023-11-17 01:53:36 30m avg rate is 105672.64 in 30 mins
2023-11-17 02:23:39 30m avg rate is 105933.44 in 30 mins
2023-11-17 02:53:42 30m avg rate is 105488.47 in 30 mins
2023-11-17 03:23:45 30m avg rate is 105817.17 in 30 mins
2023-11-17 03:41:54 set_voltage_by_steps to 1376.
2023-11-17 03:51:49 set_voltage_by_steps to 1366.
2023-11-17 03:53:48 30m avg rate is 106192.82 in 30 mins
2023-11-17 04:23:20 set_voltage_by_steps to 1376.
2023-11-17 04:23:52 30m avg rate is 105652.52 in 30 mins
2023-11-17 04:53:55 30m avg rate is 105818.39 in 30 mins
2023-11-17 05:23:58 30m avg rate is 105822.05 in 30 mins
2023-11-17 05:54:01 30m avg rate is 105503.75 in 30 mins
2023-11-17 06:24:04 30m avg rate is 105808.02 in 30 mins
2023-11-17 06:54:07 30m avg rate is 106344.06 in 30 mins
2023-11-17 07:03:24 set_voltage_by_steps to 1366.
2023-11-17 07:24:10 30m avg rate is 105718.99 in 30 mins
2023-11-17 07:54:14 30m avg rate is 105917.18 in 30 mins
2023-11-17 08:24:17 30m avg rate is 105345.78 in 30 mins
2023-11-17 08:25:09 set_voltage_by_steps to 1376.
2023-11-17 08:27:38 set_voltage_by_steps to 1366.
2023-11-17 08:54:20 30m avg rate is 105778.02 in 30 mins
2023-11-17 09:24:23 30m avg rate is 105143.31 in 30 mins
2023-11-17 09:54:26 30m avg rate is 105560.43 in 30 mins
2023-11-17 10:24:29 30m avg rate is 105759.24 in 30 mins
2023-11-17 10:54:33 30m avg rate is 105891.57 in 30 mins
2023-11-17 11:24:36 30m avg rate is 105998.90 in 30 mins
2023-11-17 11:54:39 30m avg rate is 105615.93 in 30 mins
2023-11-17 12:24:42 30m avg rate is 105847.50 in 30 mins
2023-11-17 12:54:45 30m avg rate is 106303.81 in 30 mins
2023-11-17 13:24:48 30m avg rate is 105628.12 in 30 mins
2023-11-17 13:54:52 30m avg rate is 105357.36 in 30 mins
2023-11-17 14:24:55 30m avg rate is 105203.69 in 30 mins
2023-11-17 14:54:58 30m avg rate is 106128.18 in 30 mins
2023-11-17 15:25:01 30m avg rate is 105826.78 in 30 mins
2023-11-17 15:55:04 30m avg rate is 105684.23 in 30 mins
2023-11-17 16:25:07 30m avg rate is 106047.07 in 30 mins
2023-11-17 16:55:10 30m avg rate is 105432.98 in 30 mins
2023-11-17 17:25:14 30m avg rate is 105667.76 in 30 mins
2023-11-17 17:55:17 30m avg rate is 106442.24 in 30 mins
2023-11-17 18:25:20 30m avg rate is 105626.30 in 30 mins
2023-11-17 18:55:23 30m avg rate is 105782.28 in 30 mins
2023-11-17 19:25:26 30m avg rate is 105576.29 in 30 mins
2023-11-17 19:55:29 30m avg rate is 105340.29 in 30 mins
2023-11-17 20:25:33 30m avg rate is 105564.70 in 30 mins
2023-11-17 20:55:36 30m avg rate is 105665.32 in 30 mins
2023-11-17 21:00:33 set_voltage_by_steps to 1376.
2023-11-17 21:25:39 30m avg rate is 106106.23 in 30 mins
2023-11-17 21:39:18 set_voltage_by_steps to 1366.
2023-11-17 21:41:17 set_voltage_by_steps to 1376.
2023-11-17 21:47:39 set_voltage_by_steps to 1366.
2023-11-17 21:52:25 set_voltage_by_steps to 1376.
2023-11-17 21:55:42 30m avg rate is 105572.62 in 30 mins
2023-11-17 22:10:36 set_voltage_by_steps to 1366.
2023-11-17 22:25:45 30m avg rate is 105535.43 in 30 mins
2023-11-17 22:55:48 30m avg rate is 105415.30 in 30 mins
2023-11-17 23:25:51 30m avg rate is 105764.12 in 30 mins
2023-11-17 23:55:55 30m avg rate is 105815.34 in 30 mins
2023-11-18 00:25:58 30m avg rate is 105812.29 in 30 mins
2023-11-18 00:56:01 30m avg rate is 106083.66 in 30 mins
2023-11-18 01:26:04 30m avg rate is 105850.55 in 30 mins
2023-11-18 01:56:07 30m avg rate is 106033.66 in 30 mins
2023-11-18 02:26:10 30m avg rate is 106041.58 in 30 mins
2023-11-18 02:56:13 30m avg rate is 105915.35 in 30 mins
2023-11-18 03:20:09 set_voltage_by_steps to 1376.
2023-11-18 03:26:17 30m avg rate is 105173.20 in 30 mins
2023-11-18 03:56:20 30m avg rate is 105643.37 in 30 mins
2023-11-18 04:26:23 30m avg rate is 105709.23 in 30 mins
2023-11-18 04:56:26 30m avg rate is 105514.11 in 30 mins
2023-11-18 05:26:29 30m avg rate is 105886.08 in 30 mins
2023-11-18 05:56:32 30m avg rate is 105660.45 in 30 mins
2023-11-18 06:26:35 30m avg rate is 105645.81 in 30 mins
2023-11-18 06:56:39 30m avg rate is 105634.83 in 30 mins
2023-11-18 07:26:42 30m avg rate is 105579.34 in 30 mins
2023-11-18 07:56:45 30m avg rate is 105416.59 in 30 mins
2023-11-18 08:26:48 30m avg rate is 105794.00 in 30 mins
2023-11-18 08:56:51 30m avg rate is 106197.70 in 30 mins
2023-11-18 09:26:54 30m avg rate is 106064.15 in 30 mins
2023-11-18 09:56:58 30m avg rate is 105967.19 in 30 mins
2023-11-18 10:27:01 30m avg rate is 105790.95 in 30 mins
2023-11-18 10:57:04 30m avg rate is 106126.96 in 30 mins
2023-11-18 11:27:07 30m avg rate is 105244.72 in 30 mins
2023-11-18 11:57:10 30m avg rate is 105986.09 in 30 mins
2023-11-18 12:27:13 30m avg rate is 105636.66 in 30 mins
2023-11-18 12:57:16 30m avg rate is 105150.63 in 30 mins
2023-11-18 13:27:20 30m avg rate is 105990.36 in 30 mins
2023-11-18 13:57:23 30m avg rate is 105295.16 in 30 mins
2023-11-18 14:27:26 30m avg rate is 105270.16 in 30 mins
2023-11-18 14:57:29 30m avg rate is 105476.93 in 30 mins
2023-11-18 15:27:32 30m avg rate is 106075.73 in 30 mins
2023-11-18 15:57:35 30m avg rate is 106207.46 in 30 mins
2023-11-18 16:27:38 30m avg rate is 106003.78 in 30 mins
2023-11-18 16:57:42 30m avg rate is 106066.59 in 30 mins
2023-11-18 17:27:45 30m avg rate is 105701.91 in 30 mins
2023-11-18 17:57:48 30m avg rate is 105559.21 in 30 mins
2023-11-18 18:27:51 30m avg rate is 106050.73 in 30 mins
2023-11-18 18:57:54 30m avg rate is 106455.65 in 30 mins
2023-11-18 19:02:53 set_voltage_by_steps to 1386.
2023-11-18 19:27:57 30m avg rate is 105976.33 in 30 mins
2023-11-18 19:58:01 30m avg rate is 106134.89 in 30 mins
2023-11-18 20:28:04 30m avg rate is 105789.12 in 30 mins
2023-11-18 20:46:15 chain avg vol drop to 9.54
2023-11-18 20:46:15 Sweep error string = V:1.
2023-11-18 20:46:15 ERROR_POWER_LOST: pic check voltage drop
2023-11-18 20:46:15 stop_mining: pic check voltage drop
2023-11-18 20:46:15 uninit_temp_info
2023-11-18 20:46:15 do not read temp anymore...
2023-11-18 20:46:15 cancel thread
2023-11-18 20:46:15 cancel thread
2023-11-18 20:46:15 ****power off hashboard****
2023-11-18 20:46:16 temp monitor thread exit
2023-11-18 20:58:06 avg rate is lower than ideal rate, 64054.63 in 30 mins
2023-11-18 20:58:06 30m avg rate is 64054.63 in 30 mins
2023-11-18 20:58:06 chain 0 hash rate 7491.00 low in 15 mins
2023-11-18 20:58:06 chain 1 hash rate 7574.00 low in 15 mins
2023-11-18 20:58:06 chain 2 hash rate 7443.00 low in 15 mins
2023-11-18 21:13:07 chain 0 hash rate 0.00 low in 15 mins
2023-11-18 21:13:07 chain 1 hash rate 0.00 low in 15 mins
2023-11-18 21:13:07 chain 2 hash rate 0.00 low in 15 mins
2023-11-18 21:28:07 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-18 21:28:07 30m avg rate is 0.00 in 30 mins
2023-11-18 21:58:08 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-18 21:58:08 30m avg rate is 0.00 in 30 mins
2023-11-18 22:28:09 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-18 22:28:09 30m avg rate is 0.00 in 30 mins
2023-11-18 22:58:10 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-18 22:58:10 30m avg rate is 0.00 in 30 mins
2023-11-18 23:28:11 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-18 23:28:11 30m avg rate is 0.00 in 30 mins
2023-11-18 23:58:12 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-18 23:58:12 30m avg rate is 0.00 in 30 mins
2023-11-19 00:28:14 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 00:28:14 30m avg rate is 0.00 in 30 mins
2023-11-19 00:58:15 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 00:58:15 30m avg rate is 0.00 in 30 mins
2023-11-19 01:28:16 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 01:28:16 30m avg rate is 0.00 in 30 mins
2023-11-19 01:58:17 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 01:58:17 30m avg rate is 0.00 in 30 mins
2023-11-19 02:28:18 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 02:28:18 30m avg rate is 0.00 in 30 mins
2023-11-19 02:58:19 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 02:58:19 30m avg rate is 0.00 in 30 mins
2023-11-19 03:28:20 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 03:28:20 30m avg rate is 0.00 in 30 mins
2023-11-19 03:58:21 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 03:58:21 30m avg rate is 0.00 in 30 mins
2023-11-19 04:28:22 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 04:28:22 30m avg rate is 0.00 in 30 mins
2023-11-19 04:58:23 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 04:58:23 30m avg rate is 0.00 in 30 mins
2023-11-19 05:28:24 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 05:28:24 30m avg rate is 0.00 in 30 mins
2023-11-19 05:58:25 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 05:58:25 30m avg rate is 0.00 in 30 mins
2023-11-19 06:28:27 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 06:28:27 30m avg rate is 0.00 in 30 mins
2023-11-19 06:58:28 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 06:58:28 30m avg rate is 0.00 in 30 mins
2023-11-19 07:28:29 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 07:28:29 30m avg rate is 0.00 in 30 mins
2023-11-19 07:58:30 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 07:58:30 30m avg rate is 0.00 in 30 mins
2023-11-19 08:28:31 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 08:28:31 30m avg rate is 0.00 in 30 mins
2023-11-19 08:58:32 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 08:58:32 30m avg rate is 0.00 in 30 mins
2023-11-19 09:28:33 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 09:28:33 30m avg rate is 0.00 in 30 mins
2023-11-19 09:58:34 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 09:58:34 30m avg rate is 0.00 in 30 mins
2023-11-19 10:28:35 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 10:28:35 30m avg rate is 0.00 in 30 mins
2023-11-19 10:58:36 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 10:58:36 30m avg rate is 0.00 in 30 mins
2023-11-19 11:28:37 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 11:28:37 30m avg rate is 0.00 in 30 mins
2023-11-19 11:58:38 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 11:58:38 30m avg rate is 0.00 in 30 mins
2023-11-19 12:28:40 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 12:28:40 30m avg rate is 0.00 in 30 mins
2023-11-19 12:58:41 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 12:58:41 30m avg rate is 0.00 in 30 mins
2023-11-19 13:28:42 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 13:28:42 30m avg rate is 0.00 in 30 mins
2023-11-19 13:58:43 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 13:58:43 30m avg rate is 0.00 in 30 mins
2023-11-19 14:28:44 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 14:28:44 30m avg rate is 0.00 in 30 mins
2023-11-19 14:58:45 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 14:58:45 30m avg rate is 0.00 in 30 mins
2023-11-19 15:28:46 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 15:28:46 30m avg rate is 0.00 in 30 mins
2023-11-19 15:58:47 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 15:58:47 30m avg rate is 0.00 in 30 mins
2023-11-19 16:28:48 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 16:28:48 30m avg rate is 0.00 in 30 mins
2023-11-19 16:58:49 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 16:58:49 30m avg rate is 0.00 in 30 mins
2023-11-19 17:28:50 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 17:28:50 30m avg rate is 0.00 in 30 mins
2023-11-19 17:58:51 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 17:58:51 30m avg rate is 0.00 in 30 mins
2023-11-19 18:28:52 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 18:28:52 30m avg rate is 0.00 in 30 mins
2023-11-19 18:58:54 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 18:58:54 30m avg rate is 0.00 in 30 mins
2023-11-19 19:28:55 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 19:28:55 30m avg rate is 0.00 in 30 mins
2023-11-19 19:58:56 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 19:58:56 30m avg rate is 0.00 in 30 mins
2023-11-19 20:28:57 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 20:28:57 30m avg rate is 0.00 in 30 mins
2023-11-19 20:58:58 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 20:58:58 30m avg rate is 0.00 in 30 mins
2023-11-19 21:28:59 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 21:28:59 30m avg rate is 0.00 in 30 mins
2023-11-19 21:59:00 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 21:59:00 30m avg rate is 0.00 in 30 mins
2023-11-19 22:29:01 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 22:29:01 30m avg rate is 0.00 in 30 mins
2023-11-19 22:59:02 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 22:59:02 30m avg rate is 0.00 in 30 mins
2023-11-19 23:29:03 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 23:29:03 30m avg rate is 0.00 in 30 mins
2023-11-19 23:59:04 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-19 23:59:04 30m avg rate is 0.00 in 30 mins
2023-11-20 00:29:05 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 00:29:05 30m avg rate is 0.00 in 30 mins
2023-11-20 00:59:06 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 00:59:06 30m avg rate is 0.00 in 30 mins
2023-11-20 01:29:07 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 01:29:07 30m avg rate is 0.00 in 30 mins
2023-11-20 01:59:08 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 01:59:08 30m avg rate is 0.00 in 30 mins
2023-11-20 02:29:09 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 02:29:09 30m avg rate is 0.00 in 30 mins
2023-11-20 02:59:11 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 02:59:11 30m avg rate is 0.00 in 30 mins
2023-11-20 03:29:12 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 03:29:12 30m avg rate is 0.00 in 30 mins
2023-11-20 03:59:13 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 03:59:13 30m avg rate is 0.00 in 30 mins
2023-11-20 04:29:14 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 04:29:14 30m avg rate is 0.00 in 30 mins
2023-11-20 04:59:15 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 04:59:15 30m avg rate is 0.00 in 30 mins
2023-11-20 05:29:16 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 05:29:16 30m avg rate is 0.00 in 30 mins
2023-11-20 05:59:17 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 05:59:17 30m avg rate is 0.00 in 30 mins
2023-11-20 06:29:18 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 06:29:18 30m avg rate is 0.00 in 30 mins
2023-11-20 06:59:19 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 06:59:19 30m avg rate is 0.00 in 30 mins
2023-11-20 07:29:20 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 07:29:20 30m avg rate is 0.00 in 30 mins
2023-11-20 07:59:21 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 07:59:21 30m avg rate is 0.00 in 30 mins
2023-11-20 08:29:22 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 08:29:22 30m avg rate is 0.00 in 30 mins
2023-11-20 08:59:23 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 08:59:23 30m avg rate is 0.00 in 30 mins
2023-11-20 09:29:24 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 09:29:24 30m avg rate is 0.00 in 30 mins
2023-11-20 09:59:25 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 09:59:25 30m avg rate is 0.00 in 30 mins
2023-11-20 10:29:26 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 10:29:26 30m avg rate is 0.00 in 30 mins
2023-11-20 10:59:27 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 10:59:27 30m avg rate is 0.00 in 30 mins
2023-11-20 11:29:29 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 11:29:29 30m avg rate is 0.00 in 30 mins
2023-11-20 11:59:30 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 11:59:30 30m avg rate is 0.00 in 30 mins
2023-11-20 12:29:31 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 12:29:31 30m avg rate is 0.00 in 30 mins
2023-11-20 12:59:32 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 12:59:32 30m avg rate is 0.00 in 30 mins
2023-11-20 13:29:33 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 13:29:33 30m avg rate is 0.00 in 30 mins
2023-11-20 13:59:34 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 13:59:34 30m avg rate is 0.00 in 30 mins
2023-11-20 14:29:35 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 14:29:35 30m avg rate is 0.00 in 30 mins
2023-11-20 14:59:36 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 14:59:36 30m avg rate is 0.00 in 30 mins
2023-11-20 15:29:37 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 15:29:37 30m avg rate is 0.00 in 30 mins
2023-11-20 15:59:38 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 15:59:38 30m avg rate is 0.00 in 30 mins
2023-11-20 16:29:39 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 16:29:39 30m avg rate is 0.00 in 30 mins
2023-11-20 16:59:40 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 16:59:40 30m avg rate is 0.00 in 30 mins
2023-11-20 17:29:41 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 17:29:41 30m avg rate is 0.00 in 30 mins
2023-11-20 17:59:42 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 17:59:42 30m avg rate is 0.00 in 30 mins
2023-11-20 18:29:43 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 18:29:43 30m avg rate is 0.00 in 30 mins
2023-11-20 18:59:44 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 18:59:44 30m avg rate is 0.00 in 30 mins
2023-11-20 19:29:45 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 19:29:45 30m avg rate is 0.00 in 30 mins
2023-11-20 19:59:46 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 19:59:46 30m avg rate is 0.00 in 30 mins
2023-11-20 20:29:48 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 20:29:48 30m avg rate is 0.00 in 30 mins
2023-11-20 20:59:49 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 20:59:49 30m avg rate is 0.00 in 30 mins
2023-11-20 21:29:50 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 21:29:50 30m avg rate is 0.00 in 30 mins
2023-11-20 21:59:51 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 21:59:51 30m avg rate is 0.00 in 30 mins
2023-11-20 22:29:52 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 22:29:52 30m avg rate is 0.00 in 30 mins
2023-11-20 22:59:53 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 22:59:53 30m avg rate is 0.00 in 30 mins
2023-11-20 23:29:54 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 23:29:54 30m avg rate is 0.00 in 30 mins
2023-11-20 23:59:55 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-20 23:59:55 30m avg rate is 0.00 in 30 mins
2023-11-21 00:29:56 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 00:29:56 30m avg rate is 0.00 in 30 mins
2023-11-21 00:59:57 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 00:59:57 30m avg rate is 0.00 in 30 mins
2023-11-21 01:29:58 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 01:29:58 30m avg rate is 0.00 in 30 mins
2023-11-21 01:59:59 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 01:59:59 30m avg rate is 0.00 in 30 mins
2023-11-21 02:30:00 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 02:30:00 30m avg rate is 0.00 in 30 mins
2023-11-21 03:00:01 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 03:00:01 30m avg rate is 0.00 in 30 mins
2023-11-21 03:30:02 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 03:30:02 30m avg rate is 0.00 in 30 mins
2023-11-21 04:00:03 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 04:00:03 30m avg rate is 0.00 in 30 mins
2023-11-21 04:30:05 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 04:30:05 30m avg rate is 0.00 in 30 mins
2023-11-21 05:00:06 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 05:00:06 30m avg rate is 0.00 in 30 mins
2023-11-21 05:30:07 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 05:30:07 30m avg rate is 0.00 in 30 mins
2023-11-21 06:00:08 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 06:00:08 30m avg rate is 0.00 in 30 mins
2023-11-21 06:30:09 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 06:30:09 30m avg rate is 0.00 in 30 mins
2023-11-21 07:00:10 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 07:00:10 30m avg rate is 0.00 in 30 mins
2023-11-21 07:30:11 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 07:30:11 30m avg rate is 0.00 in 30 mins
2023-11-21 08:00:12 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 08:00:12 30m avg rate is 0.00 in 30 mins
2023-11-21 08:30:13 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 08:30:13 30m avg rate is 0.00 in 30 mins
2023-11-21 09:00:14 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 09:00:14 30m avg rate is 0.00 in 30 mins
2023-11-21 09:30:15 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 09:30:15 30m avg rate is 0.00 in 30 mins
2023-11-21 10:00:16 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 10:00:16 30m avg rate is 0.00 in 30 mins
2023-11-21 10:30:17 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 10:30:17 30m avg rate is 0.00 in 30 mins
2023-11-21 11:00:18 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 11:00:18 30m avg rate is 0.00 in 30 mins
2023-11-21 11:30:19 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 11:30:19 30m avg rate is 0.00 in 30 mins
2023-11-21 12:00:20 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 12:00:20 30m avg rate is 0.00 in 30 mins
2023-11-21 12:30:21 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 12:30:21 30m avg rate is 0.00 in 30 mins
2023-11-21 13:00:22 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 13:00:22 30m avg rate is 0.00 in 30 mins
2023-11-21 13:30:24 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 13:30:24 30m avg rate is 0.00 in 30 mins
2023-11-21 14:00:25 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 14:00:25 30m avg rate is 0.00 in 30 mins
2023-11-21 14:30:26 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 14:30:26 30m avg rate is 0.00 in 30 mins
2023-11-21 15:00:27 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 15:00:27 30m avg rate is 0.00 in 30 mins
2023-11-21 15:30:28 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 15:30:28 30m avg rate is 0.00 in 30 mins
2023-11-21 16:00:29 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 16:00:29 30m avg rate is 0.00 in 30 mins
2023-11-21 16:30:30 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 16:30:30 30m avg rate is 0.00 in 30 mins
2023-11-21 17:00:31 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 17:00:31 30m avg rate is 0.00 in 30 mins
2023-11-21 17:30:32 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 17:30:32 30m avg rate is 0.00 in 30 mins
2023-11-21 18:00:33 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 18:00:33 30m avg rate is 0.00 in 30 mins
2023-11-21 18:30:34 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 18:30:34 30m avg rate is 0.00 in 30 mins
2023-11-21 19:00:35 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 19:00:35 30m avg rate is 0.00 in 30 mins
2023-11-21 19:30:36 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 19:30:36 30m avg rate is 0.00 in 30 mins
2023-11-21 20:00:37 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 20:00:37 30m avg rate is 0.00 in 30 mins
2023-11-21 20:30:38 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 20:30:38 30m avg rate is 0.00 in 30 mins
2023-11-21 21:00:39 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 21:00:39 30m avg rate is 0.00 in 30 mins
2023-11-21 21:30:40 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 21:30:40 30m avg rate is 0.00 in 30 mins
2023-11-21 22:00:42 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 22:00:42 30m avg rate is 0.00 in 30 mins
2023-11-21 22:30:43 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 22:30:43 30m avg rate is 0.00 in 30 mins
2023-11-21 23:00:44 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 23:00:44 30m avg rate is 0.00 in 30 mins
2023-11-21 23:30:45 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-21 23:30:45 30m avg rate is 0.00 in 30 mins
2023-11-22 00:00:46 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 00:00:46 30m avg rate is 0.00 in 30 mins
2023-11-22 00:30:47 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 00:30:47 30m avg rate is 0.00 in 30 mins
2023-11-22 01:00:48 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 01:00:48 30m avg rate is 0.00 in 30 mins
2023-11-22 01:30:49 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 01:30:49 30m avg rate is 0.00 in 30 mins
2023-11-22 02:00:50 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 02:00:50 30m avg rate is 0.00 in 30 mins
2023-11-22 02:30:51 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 02:30:51 30m avg rate is 0.00 in 30 mins
2023-11-22 03:00:52 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 03:00:52 30m avg rate is 0.00 in 30 mins
2023-11-22 03:30:53 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 03:30:53 30m avg rate is 0.00 in 30 mins
2023-11-22 04:00:54 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 04:00:54 30m avg rate is 0.00 in 30 mins
2023-11-22 04:30:55 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 04:30:55 30m avg rate is 0.00 in 30 mins
2023-11-22 05:00:56 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 05:00:56 30m avg rate is 0.00 in 30 mins
2023-11-22 05:30:57 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 05:30:57 30m avg rate is 0.00 in 30 mins
2023-11-22 06:00:58 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 06:00:58 30m avg rate is 0.00 in 30 mins
2023-11-22 06:31:00 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 06:31:00 30m avg rate is 0.00 in 30 mins
2023-11-22 07:01:01 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 07:01:01 30m avg rate is 0.00 in 30 mins
2023-11-22 07:31:02 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 07:31:02 30m avg rate is 0.00 in 30 mins
2023-11-22 08:01:03 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 08:01:03 30m avg rate is 0.00 in 30 mins
2023-11-22 08:31:04 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 08:31:04 30m avg rate is 0.00 in 30 mins
2023-11-22 09:01:05 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 09:01:05 30m avg rate is 0.00 in 30 mins
2023-11-22 09:16:08 ****power off hashboard****
2023-11-22 09:16:33 Open miner sn file /config/sn error
2023-11-22 09:16:33 Miner compile time: Mon Dec 26 19:16:16 CST 2022 type: Antminer BHB42XXX sn :
2023-11-22 09:16:34 This is fix-freq version
2023-11-22 09:16:34 Miner compile time: Mon Dec 26 19:16:16 CST 2022 type: Antminer BHB42XXX
2023-11-22 09:16:34 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 19:26:44
2023-11-22 09:16:34 opt_multi_version     = 1
2023-11-22 09:16:34 opt_bitmain_ab        = 1
2023-11-22 09:16:34 mid_auto_gen          = 1
2023-11-22 09:16:34 opt_bitmain_work_mode = 0
2023-11-22 09:16:34 port 439 already exported
2023-11-22 09:16:34 port 454 already exported
2023-11-22 09:16:34 port 440 already exported
2023-11-22 09:16:34 port 455 already exported
2023-11-22 09:16:34 port 441 already exported
2023-11-22 09:16:34 port 456 already exported
2023-11-22 09:16:34 port 438 already exported
2023-11-22 09:16:34 port 453 already exported
2023-11-22 09:16:34 port 446 already exported
2023-11-22 09:16:34 port 445 already exported
2023-11-22 09:16:34 Note: front fan is power on!
2023-11-22 09:16:34 Note: rear fan is power on!
2023-11-22 09:16:34 start the http log.
2023-11-22 09:16:34 httpListenThread start ret=0
2023-11-22 09:16:34 start listen on 6060 ...
2023-11-22 09:16:34 bad chain id = 3
2023-11-22 09:16:37 bad chain id = 3
2023-11-22 09:16:39 ==========================capability start==========================
2023-11-22 09:16:39 board num = 3
2023-11-22 09:16:39 board id = 0, chain num = 1
2023-11-22 09:16:39 	chain id = 0
2023-11-22 09:16:39 board id = 1, chain num = 1
2023-11-22 09:16:39 	chain id = 1
2023-11-22 09:16:39 board id = 2, chain num = 1
2023-11-22 09:16:39 	chain id = 2
2023-11-22 09:16:39 ==========================capability end============================
2023-11-22 09:16:39 chain num = 3
2023-11-22 09:16:39 skip loading levels for now
2023-11-22 09:16:43 load chain 0 eeprom data
2023-11-22 09:16:46 load chain 1 eeprom data
2023-11-22 09:16:49 load chain 2 eeprom data
2023-11-22 09:16:49 i2c_sim_init start
2023-11-22 09:16:49 init gpio477
2023-11-22 09:16:49 init gpio476
2023-11-22 09:16:49 i2c_sim_init end
2023-11-22 09:16:50 power open power_version = 0x71
2023-11-22 09:16:53 power is not Calibrated
2023-11-22 09:16:54 miner type: Antminer S19j Pro
2023-11-22 09:16:54 multi machine mode
2023-11-22 09:16:54 load machine BHB42601 conf
2023-11-22 09:16:54 machine : BHB42601 
2023-11-22 09:16:54 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-11-22 09:16:54 abandon mix board!
2023-11-22 09:16:54 abandon mix board!
2023-11-22 09:16:54 fan_eft : 0  fan_pwm : 100
2023-11-22 09:16:54 create thread get_nonce_and_register_thread
2023-11-22 09:16:54 fixed working voltage = 1360
2023-11-22 09:16:54 fixed frequency is 545
2023-11-22 09:16:54 Chain [0] PCB Version: 0x0130
2023-11-22 09:16:54 Chain [0] BOM Version: 0x0010
2023-11-22 09:16:54 Chain [1] PCB Version: 0x0130
2023-11-22 09:16:54 Chain [1] BOM Version: 0x0010
2023-11-22 09:16:54 Chain [2] PCB Version: 0x0130
2023-11-22 09:16:54 Chain [2] BOM Version: 0x0010
2023-11-22 09:16:54 bad chain id = 3
2023-11-22 09:16:54 Fan check passed.
2023-11-22 09:16:54 uart_trans addr:0xf73ca000.
2023-11-22 09:16:55 chain[0] PIC jump to app
2023-11-22 09:16:57 Check chain[0] PIC fw version=0x89
2023-11-22 09:16:58 chain[1] PIC jump to app
2023-11-22 09:16:59 Check chain[1] PIC fw version=0x89
2023-11-22 09:17:00 chain[2] PIC jump to app
2023-11-22 09:17:02 Check chain[2] PIC fw version=0x89
2023-11-22 09:17:02 create thread pic_heart_beat_thread
2023-11-22 09:17:02 max sensor num = 4
2023-11-22 09:17:02 STATUS_INITED: soc init done!
2023-11-22 09:17:02 temperature_monitor_thread start...
2023-11-22 09:17:49 start to init...
2023-11-22 09:17:49 warning:power is not calibration.
2023-11-22 09:17:51 power type version: 0x0071
2023-11-22 09:17:51 Initializing the power, please wait, this may take up to 2 minutes...
2023-11-22 09:18:22 Slept 30 seconds, diff = 0.
2023-11-22 09:18:22 set_voltage_by_steps to 1500.
2023-11-22 09:18:24 chain avg vol rise to 15.14
2023-11-22 09:18:26 start up min temp by 75a = 16
2023-11-22 09:18:36 Chain[0]: find 126 asic, times 0
2023-11-22 09:18:46 Chain[1]: find 126 asic, times 0
2023-11-22 09:18:56 Chain[2]: find 126 asic, times 0
2023-11-22 09:19:01 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2023-11-22 09:19:05 Bring up temperature is 16
2023-11-22 09:19:05 set UART baud to 3000000
2023-11-22 09:19:05 create thread check_miner_status_thread
2023-11-22 09:19:05 create thread check_system_work_thread
2023-11-22 09:19:05 set_voltage_by_steps to 1450.
2023-11-22 09:19:07 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2023-11-22 09:19:07 start do_core_reset
2023-11-22 09:19:27 end do_core_reset
2023-11-22 09:19:27 chain[0] min = 545 max =545
2023-11-22 09:19:27 chain[1] min = 545 max =545
2023-11-22 09:19:27 chain[2] min = 545 max =545
2023-11-22 09:19:27 1.inc all chain freq to 545
2023-11-22 09:19:27 fixed step freq_start = 50, freq_end = 545, freq_step = 6.25
2023-11-22 09:19:27 chain = 0 set freq to 56.25
2023-11-22 09:19:27 chain = 1 set freq to 56.25
2023-11-22 09:19:27 chain = 2 set freq to 56.25
2023-11-22 09:19:27 chain = 0 set freq to 62.50
2023-11-22 09:19:27 chain = 1 set freq to 62.50
2023-11-22 09:19:27 chain = 2 set freq to 62.50
2023-11-22 09:19:27 chain = 0 set freq to 68.75
2023-11-22 09:19:27 chain = 1 set freq to 68.75
2023-11-22 09:19:27 chain = 2 set freq to 68.75
2023-11-22 09:19:28 chain = 0 set freq to 75.00
2023-11-22 09:19:28 chain = 1 set freq to 75.00
2023-11-22 09:19:28 chain = 2 set freq to 75.00
2023-11-22 09:19:28 chain = 0 set freq to 81.25
2023-11-22 09:19:28 chain = 1 set freq to 81.25
2023-11-22 09:19:28 chain = 2 set freq to 81.25
2023-11-22 09:19:28 chain = 0 set freq to 87.50
2023-11-22 09:19:28 chain = 1 set freq to 87.50
2023-11-22 09:19:28 chain = 2 set freq to 87.50
2023-11-22 09:19:28 chain = 0 set freq to 93.75
2023-11-22 09:19:28 chain = 1 set freq to 93.75
2023-11-22 09:19:28 chain = 2 set freq to 93.75
2023-11-22 09:19:29 chain = 0 set freq to 100.00
2023-11-22 09:19:29 chain = 1 set freq to 100.00
2023-11-22 09:19:29 chain = 2 set freq to 100.00
2023-11-22 09:19:29 chain = 0 set freq to 106.25
2023-11-22 09:19:29 chain = 1 set freq to 106.25
2023-11-22 09:19:29 chain = 2 set freq to 106.25
2023-11-22 09:19:29 chain = 0 set freq to 112.50
2023-11-22 09:19:29 chain = 1 set freq to 112.50
2023-11-22 09:19:29 chain = 2 set freq to 112.50
2023-11-22 09:19:30 chain = 0 set freq to 118.75
2023-11-22 09:19:30 chain = 1 set freq to 118.75
2023-11-22 09:19:30 chain = 2 set freq to 118.75
2023-11-22 09:19:30 chain = 0 set freq to 125.00
2023-11-22 09:19:30 chain = 1 set freq to 125.00
2023-11-22 09:19:30 chain = 2 set freq to 125.00
2023-11-22 09:19:30 chain = 0 set freq to 131.25
2023-11-22 09:19:30 chain = 1 set freq to 131.25
2023-11-22 09:19:30 chain = 2 set freq to 131.25
2023-11-22 09:19:31 chain = 0 set freq to 137.50
2023-11-22 09:19:31 chain = 1 set freq to 137.50
2023-11-22 09:19:31 chain = 2 set freq to 137.50
2023-11-22 09:19:31 chain = 0 set freq to 143.75
2023-11-22 09:19:31 chain = 1 set freq to 143.75
2023-11-22 09:19:31 chain = 2 set freq to 143.75
2023-11-22 09:19:31 chain = 0 set freq to 150.00
2023-11-22 09:19:31 chain = 1 set freq to 150.00
2023-11-22 09:19:31 chain = 2 set freq to 150.00
2023-11-22 09:19:31 chain = 0 set freq to 156.25
2023-11-22 09:19:31 chain = 1 set freq to 156.25
2023-11-22 09:19:31 chain = 2 set freq to 156.25
2023-11-22 09:19:32 chain = 0 set freq to 162.50
2023-11-22 09:19:32 chain = 1 set freq to 162.50
2023-11-22 09:19:32 chain = 2 set freq to 162.50
2023-11-22 09:19:32 chain = 0 set freq to 168.75
2023-11-22 09:19:32 chain = 1 set freq to 168.75
2023-11-22 09:19:32 chain = 2 set freq to 168.75
2023-11-22 09:19:32 chain = 0 set freq to 175.00
2023-11-22 09:19:32 chain = 1 set freq to 175.00
2023-11-22 09:19:32 chain = 2 set freq to 175.00
2023-11-22 09:19:33 chain = 0 set freq to 181.25
2023-11-22 09:19:33 chain = 1 set freq to 181.25
2023-11-22 09:19:33 chain = 2 set freq to 181.25
2023-11-22 09:19:33 chain = 0 set freq to 187.50
2023-11-22 09:19:33 chain = 1 set freq to 187.50
2023-11-22 09:19:33 chain = 2 set freq to 187.50
2023-11-22 09:19:33 chain = 0 set freq to 193.75
2023-11-22 09:19:33 chain = 1 set freq to 193.75
2023-11-22 09:19:33 chain = 2 set freq to 193.75
2023-11-22 09:19:34 chain = 0 set freq to 200.00
2023-11-22 09:19:34 chain = 1 set freq to 200.00
2023-11-22 09:19:34 chain = 2 set freq to 200.00
2023-11-22 09:19:34 chain = 0 set freq to 206.25
2023-11-22 09:19:34 chain = 1 set freq to 206.25
2023-11-22 09:19:34 chain = 2 set freq to 206.25
2023-11-22 09:19:34 chain = 0 set freq to 212.50
2023-11-22 09:19:34 chain = 1 set freq to 212.50
2023-11-22 09:19:34 chain = 2 set freq to 212.50
2023-11-22 09:19:34 chain = 0 set freq to 218.75
2023-11-22 09:19:34 chain = 1 set freq to 218.75
2023-11-22 09:19:34 chain = 2 set freq to 218.75
2023-11-22 09:19:35 chain = 0 set freq to 225.00
2023-11-22 09:19:35 chain = 1 set freq to 225.00
2023-11-22 09:19:35 chain = 2 set freq to 225.00
2023-11-22 09:19:35 chain = 0 set freq to 231.25
2023-11-22 09:19:35 chain = 1 set freq to 231.25
2023-11-22 09:19:35 chain = 2 set freq to 231.25
2023-11-22 09:19:35 chain = 0 set freq to 237.50
2023-11-22 09:19:35 chain = 1 set freq to 237.50
2023-11-22 09:19:35 chain = 2 set freq to 237.50
2023-11-22 09:19:36 chain = 0 set freq to 243.75
2023-11-22 09:19:36 chain = 1 set freq to 243.75
2023-11-22 09:19:36 chain = 2 set freq to 243.75
2023-11-22 09:19:36 chain = 0 set freq to 250.00
2023-11-22 09:19:36 chain = 1 set freq to 250.00
2023-11-22 09:19:36 chain = 2 set freq to 250.00
2023-11-22 09:19:36 chain = 0 set freq to 256.25
2023-11-22 09:19:36 chain = 1 set freq to 256.25
2023-11-22 09:19:36 chain = 2 set freq to 256.25
2023-11-22 09:19:37 chain = 0 set freq to 262.50
2023-11-22 09:19:37 chain = 1 set freq to 262.50
2023-11-22 09:19:37 chain = 2 set freq to 262.50
2023-11-22 09:19:37 chain = 0 set freq to 268.75
2023-11-22 09:19:37 chain = 1 set freq to 268.75
2023-11-22 09:19:37 chain = 2 set freq to 268.75
2023-11-22 09:19:37 chain = 0 set freq to 275.00
2023-11-22 09:19:37 chain = 1 set freq to 275.00
2023-11-22 09:19:37 chain = 2 set freq to 275.00
2023-11-22 09:19:37 chain = 0 set freq to 281.25
2023-11-22 09:19:37 chain = 1 set freq to 281.25
2023-11-22 09:19:37 chain = 2 set freq to 281.25
2023-11-22 09:19:38 chain = 0 set freq to 287.50
2023-11-22 09:19:38 chain = 1 set freq to 287.50
2023-11-22 09:19:38 chain = 2 set freq to 287.50
2023-11-22 09:19:38 chain = 0 set freq to 293.75
2023-11-22 09:19:38 chain = 1 set freq to 293.75
2023-11-22 09:19:38 chain = 2 set freq to 293.75
2023-11-22 09:19:38 chain = 0 set freq to 300.00
2023-11-22 09:19:38 chain = 1 set freq to 300.00
2023-11-22 09:19:38 chain = 2 set freq to 300.00
2023-11-22 09:19:39 chain = 0 set freq to 306.25
2023-11-22 09:19:39 chain = 1 set freq to 306.25
2023-11-22 09:19:39 chain = 2 set freq to 306.25
2023-11-22 09:19:39 chain = 0 set freq to 312.50
2023-11-22 09:19:39 chain = 1 set freq to 312.50
2023-11-22 09:19:39 chain = 2 set freq to 312.50
2023-11-22 09:19:39 chain = 0 set freq to 318.75
2023-11-22 09:19:39 chain = 1 set freq to 318.75
2023-11-22 09:19:39 chain = 2 set freq to 318.75
2023-11-22 09:19:40 chain = 0 set freq to 325.00
2023-11-22 09:19:40 chain = 1 set freq to 325.00
2023-11-22 09:19:40 chain = 2 set freq to 325.00
2023-11-22 09:19:40 chain = 0 set freq to 331.25
2023-11-22 09:19:40 chain = 1 set freq to 331.25
2023-11-22 09:19:40 chain = 2 set freq to 331.25
2023-11-22 09:19:40 chain = 0 set freq to 337.50
2023-11-22 09:19:40 chain = 1 set freq to 337.50
2023-11-22 09:19:40 chain = 2 set freq to 337.50
2023-11-22 09:19:41 chain = 0 set freq to 343.75
2023-11-22 09:19:41 chain = 1 set freq to 343.75
2023-11-22 09:19:41 chain = 2 set freq to 343.75
2023-11-22 09:19:41 chain = 0 set freq to 350.00
2023-11-22 09:19:41 chain = 1 set freq to 350.00
2023-11-22 09:19:41 chain = 2 set freq to 350.00
2023-11-22 09:19:41 chain = 0 set freq to 356.25
2023-11-22 09:19:41 chain = 1 set freq to 356.25
2023-11-22 09:19:41 chain = 2 set freq to 356.25
2023-11-22 09:19:41 chain = 0 set freq to 362.50
2023-11-22 09:19:41 chain = 1 set freq to 362.50
2023-11-22 09:19:41 chain = 2 set freq to 362.50
2023-11-22 09:19:42 chain = 0 set freq to 368.75
2023-11-22 09:19:42 chain = 1 set freq to 368.75
2023-11-22 09:19:42 chain = 2 set freq to 368.75
2023-11-22 09:19:42 chain = 0 set freq to 375.00
2023-11-22 09:19:42 chain = 1 set freq to 375.00
2023-11-22 09:19:42 chain = 2 set freq to 375.00
2023-11-22 09:19:42 chain = 0 set freq to 381.25
2023-11-22 09:19:42 chain = 1 set freq to 381.25
2023-11-22 09:19:42 chain = 2 set freq to 381.25
2023-11-22 09:19:43 chain = 0 set freq to 387.50
2023-11-22 09:19:43 chain = 1 set freq to 387.50
2023-11-22 09:19:43 chain = 2 set freq to 387.50
2023-11-22 09:19:43 chain = 0 set freq to 393.75
2023-11-22 09:19:43 chain = 1 set freq to 393.75
2023-11-22 09:19:43 chain = 2 set freq to 393.75
2023-11-22 09:19:43 chain = 0 set freq to 400.00
2023-11-22 09:19:43 chain = 1 set freq to 400.00
2023-11-22 09:19:43 chain = 2 set freq to 400.00
2023-11-22 09:19:44 chain = 0 set freq to 406.25
2023-11-22 09:19:44 chain = 1 set freq to 406.25
2023-11-22 09:19:44 chain = 2 set freq to 406.25
2023-11-22 09:19:44 chain = 0 set freq to 412.50
2023-11-22 09:19:44 chain = 1 set freq to 412.50
2023-11-22 09:19:44 chain = 2 set freq to 412.50
2023-11-22 09:19:44 chain = 0 set freq to 418.75
2023-11-22 09:19:44 chain = 1 set freq to 418.75
2023-11-22 09:19:44 chain = 2 set freq to 418.75
2023-11-22 09:19:44 chain = 0 set freq to 425.00
2023-11-22 09:19:44 chain = 1 set freq to 425.00
2023-11-22 09:19:44 chain = 2 set freq to 425.00
2023-11-22 09:19:45 chain = 0 set freq to 431.25
2023-11-22 09:19:45 chain = 1 set freq to 431.25
2023-11-22 09:19:45 chain = 2 set freq to 431.25
2023-11-22 09:19:45 chain = 0 set freq to 437.50
2023-11-22 09:19:45 chain = 1 set freq to 437.50
2023-11-22 09:19:45 chain = 2 set freq to 437.50
2023-11-22 09:19:45 chain = 0 set freq to 443.75
2023-11-22 09:19:45 chain = 1 set freq to 443.75
2023-11-22 09:19:45 chain = 2 set freq to 443.75
2023-11-22 09:19:46 chain = 0 set freq to 450.00
2023-11-22 09:19:46 chain = 1 set freq to 450.00
2023-11-22 09:19:46 chain = 2 set freq to 450.00
2023-11-22 09:19:46 chain = 0 set freq to 456.25
2023-11-22 09:19:46 chain = 1 set freq to 456.25
2023-11-22 09:19:46 chain = 2 set freq to 456.25
2023-11-22 09:19:46 chain = 0 set freq to 462.50
2023-11-22 09:19:46 chain = 1 set freq to 462.50
2023-11-22 09:19:46 chain = 2 set freq to 462.50
2023-11-22 09:19:47 chain = 0 set freq to 468.75
2023-11-22 09:19:47 chain = 1 set freq to 468.75
2023-11-22 09:19:47 chain = 2 set freq to 468.75
2023-11-22 09:19:47 chain = 0 set freq to 475.00
2023-11-22 09:19:47 chain = 1 set freq to 475.00
2023-11-22 09:19:47 chain = 2 set freq to 475.00
2023-11-22 09:19:47 chain = 0 set freq to 481.25
2023-11-22 09:19:47 chain = 1 set freq to 481.25
2023-11-22 09:19:47 chain = 2 set freq to 481.25
2023-11-22 09:19:47 chain = 0 set freq to 487.50
2023-11-22 09:19:47 chain = 1 set freq to 487.50
2023-11-22 09:19:47 chain = 2 set freq to 487.50
2023-11-22 09:19:48 chain = 0 set freq to 493.75
2023-11-22 09:19:48 chain = 1 set freq to 493.75
2023-11-22 09:19:48 chain = 2 set freq to 493.75
2023-11-22 09:19:48 chain = 0 set freq to 500.00
2023-11-22 09:19:48 chain = 1 set freq to 500.00
2023-11-22 09:19:48 chain = 2 set freq to 500.00
2023-11-22 09:19:48 chain = 0 set freq to 506.25
2023-11-22 09:19:48 chain = 1 set freq to 506.25
2023-11-22 09:19:48 chain = 2 set freq to 506.25
2023-11-22 09:19:49 chain = 0 set freq to 512.50
2023-11-22 09:19:49 chain = 1 set freq to 512.50
2023-11-22 09:19:49 chain = 2 set freq to 512.50
2023-11-22 09:19:49 chain = 0 set freq to 518.75
2023-11-22 09:19:49 chain = 1 set freq to 518.75
2023-11-22 09:19:49 chain = 2 set freq to 518.75
2023-11-22 09:19:49 chain = 0 set freq to 525.00
2023-11-22 09:19:49 chain = 1 set freq to 525.00
2023-11-22 09:19:49 chain = 2 set freq to 525.00
2023-11-22 09:19:50 chain = 0 set freq to 531.25
2023-11-22 09:19:50 chain = 1 set freq to 531.25
2023-11-22 09:19:50 chain = 2 set freq to 531.25
2023-11-22 09:19:50 chain = 0 set freq to 537.50
2023-11-22 09:19:50 chain = 1 set freq to 537.50
2023-11-22 09:19:50 chain = 2 set freq to 537.50
2023-11-22 09:19:50 chain = 0 set freq to 543.75
2023-11-22 09:19:50 chain = 1 set freq to 543.75
2023-11-22 09:19:50 chain = 2 set freq to 543.75
2023-11-22 09:19:50 chain = 0 set freq to 545.00
2023-11-22 09:19:50 chain = 1 set freq to 545.00
2023-11-22 09:19:50 chain = 2 set freq to 545.00
2023-11-22 09:19:51 enter mixed freq cfg
2023-11-22 09:19:51 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2023-11-22 09:19:51 start do_core_reset
2023-11-22 09:20:10 end do_core_reset
2023-11-22 09:20:20 set_voltage_by_steps to 1373.
2023-11-22 09:20:22 Init done!
2023-11-22 09:20:22 STATUS_OKAY
2023-11-22 09:20:22 start the cached job
2023-11-22 09:20:22 Version num 65536
2023-11-22 09:20:22 Mask num 0x1fffe000
2023-11-22 09:20:22 opt_multi_version = 65536, interval timeout = 2837042
2023-11-22 09:20:22 freq = 545, percent = 90, hcn = 4809, timeout = 2837042
2023-11-22 09:20:22 set_start_time_point total_tv_start_sys=240 total_tv_end_sys=241
2023-11-22 09:46:16 set_voltage_by_steps to 1363.
2023-11-22 09:46:18 curr_vol = 1363, g_voltage = 1360,entrance_temp = 22
2023-11-22 09:46:18 set_voltage_by_steps to 1360.
2023-11-22 09:47:31 set_voltage_by_steps to 1370.
2023-11-22 09:49:07 30m avg rate is 106205.81 in 28 mins
2023-11-22 09:51:35 set_voltage_by_steps to 1360.
2023-11-22 09:51:58 set_voltage_by_steps to 1383.
2023-11-22 09:52:08 set_voltage_by_steps to 1393.
2023-11-22 09:52:10 set_voltage_by_steps to 1403.
2023-11-22 09:52:12 set_voltage_by_steps to 1413.
2023-11-22 09:52:14 set_voltage_by_steps to 1460.
2023-11-22 09:52:23 _pic_read_iic failed! read_back_data[0] = 0x07, read_back_data[1] = 0x3c, read_back_data[2] = 0x00
2023-11-22 09:52:25 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2023-11-22 09:52:25 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2023-11-22 09:52:41 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2023-11-22 09:52:41 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2023-11-22 09:52:41 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2023-11-22 09:52:41 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2023-11-22 09:52:42 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2023-11-22 09:52:42 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2023-11-22 09:52:43 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2023-11-22 09:52:43 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2023-11-22 09:52:43 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2023-11-22 09:52:43 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2023-11-22 09:52:44 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2023-11-22 09:52:44 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2023-11-22 09:52:45 over max temp, pcb temp 60 (max 75), chip temp 255(max 95) pcb temp rise 0 chip temp rise 0, total_exit_failure 6
2023-11-22 09:52:45 Sweep error string = J0:6.
2023-11-22 09:52:45 ERROR_TEMP_TOO_HIGH: over max temp
2023-11-22 09:52:45 stop_mining: over max temp
2023-11-22 09:52:45 uninit_temp_info
2023-11-22 09:52:45 do not read temp anymore...
2023-11-22 09:52:45 cancel thread
2023-11-22 09:52:45 cancel thread
2023-11-22 09:52:45 cancel thread
2023-11-22 09:52:45 ****power off hashboard****
2023-11-22 09:52:49 temp monitor thread exit
2023-11-22 10:04:08 chain 0 hash rate 8536.00 low in 15 mins
2023-11-22 10:04:08 chain 1 hash rate 8356.00 low in 15 mins
2023-11-22 10:04:08 chain 2 hash rate 8462.00 low in 15 mins
2023-11-22 10:19:08 avg rate is lower than ideal rate, 12677.94 in 30 mins
2023-11-22 10:19:08 30m avg rate is 12677.94 in 30 mins
2023-11-22 10:19:08 chain 0 hash rate 0.00 low in 15 mins
2023-11-22 10:19:08 chain 1 hash rate 0.00 low in 15 mins
2023-11-22 10:19:08 chain 2 hash rate 0.00 low in 15 mins
2023-11-22 10:49:09 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 10:49:09 30m avg rate is 0.00 in 30 mins
2023-11-22 11:19:11 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 11:19:11 30m avg rate is 0.00 in 30 mins
2023-11-22 11:49:12 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 11:49:12 30m avg rate is 0.00 in 30 mins
2023-11-22 12:19:13 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 12:19:13 30m avg rate is 0.00 in 30 mins
2023-11-22 12:49:14 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 12:49:14 30m avg rate is 0.00 in 30 mins
2023-11-22 13:19:15 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 13:19:15 30m avg rate is 0.00 in 30 mins
2023-11-22 13:49:16 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 13:49:16 30m avg rate is 0.00 in 30 mins
2023-11-22 14:19:17 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 14:19:17 30m avg rate is 0.00 in 30 mins
2023-11-22 14:49:18 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 14:49:18 30m avg rate is 0.00 in 30 mins
2023-11-22 15:19:19 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 15:19:19 30m avg rate is 0.00 in 30 mins
2023-11-22 15:49:20 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 15:49:20 30m avg rate is 0.00 in 30 mins
2023-11-22 16:19:21 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 16:19:21 30m avg rate is 0.00 in 30 mins
2023-11-22 16:49:23 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 16:49:23 30m avg rate is 0.00 in 30 mins
2023-11-22 17:19:24 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 17:19:24 30m avg rate is 0.00 in 30 mins
2023-11-22 17:49:25 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 17:49:25 30m avg rate is 0.00 in 30 mins
2023-11-22 18:19:26 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 18:19:26 30m avg rate is 0.00 in 30 mins
2023-11-22 18:49:27 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 18:49:27 30m avg rate is 0.00 in 30 mins
2023-11-22 19:19:28 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 19:19:28 30m avg rate is 0.00 in 30 mins
2023-11-22 19:49:29 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 19:49:29 30m avg rate is 0.00 in 30 mins
2023-11-22 20:19:30 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 20:19:30 30m avg rate is 0.00 in 30 mins
2023-11-22 20:49:31 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 20:49:31 30m avg rate is 0.00 in 30 mins
2023-11-22 21:19:32 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 21:19:32 30m avg rate is 0.00 in 30 mins
2023-11-22 21:49:33 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 21:49:33 30m avg rate is 0.00 in 30 mins
2023-11-22 22:19:34 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 22:19:34 30m avg rate is 0.00 in 30 mins
2023-11-22 22:49:36 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 22:49:36 30m avg rate is 0.00 in 30 mins
2023-11-22 23:19:37 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 23:19:37 30m avg rate is 0.00 in 30 mins
2023-11-22 23:49:38 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-22 23:49:38 30m avg rate is 0.00 in 30 mins
2023-11-23 00:19:39 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-23 00:19:39 30m avg rate is 0.00 in 30 mins
2023-11-23 00:49:40 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-23 00:49:40 30m avg rate is 0.00 in 30 mins
2023-11-23 01:19:41 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-23 01:19:41 30m avg rate is 0.00 in 30 mins
2023-11-23 01:49:42 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-23 01:49:42 30m avg rate is 0.00 in 30 mins
2023-11-23 02:19:43 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-23 02:19:43 30m avg rate is 0.00 in 30 mins
2023-11-23 02:49:44 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-23 02:49:44 30m avg rate is 0.00 in 30 mins
2023-11-23 03:19:45 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-23 03:19:45 30m avg rate is 0.00 in 30 mins
2023-11-23 03:49:46 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-23 03:49:46 30m avg rate is 0.00 in 30 mins
2023-11-23 04:19:47 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-23 04:19:47 30m avg rate is 0.00 in 30 mins
2023-11-23 04:49:49 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-23 04:49:49 30m avg rate is 0.00 in 30 mins
2023-11-23 05:19:50 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-23 05:19:50 30m avg rate is 0.00 in 30 mins
2023-11-23 05:49:51 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-23 05:49:51 30m avg rate is 0.00 in 30 mins
2023-11-23 06:19:52 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-23 06:19:52 30m avg rate is 0.00 in 30 mins
2023-11-23 06:49:53 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-23 06:49:53 30m avg rate is 0.00 in 30 mins
2023-11-23 07:19:54 avg rate is lower than ideal rate, 0.00 in 30 mins
2023-11-23 07:19:54 30m avg rate is 0.00 in 30 mins
2023-11-23 07:40:41 ****power off hashboard****
2023-11-23 07:41:05 Open miner sn file /config/sn error
2023-11-23 07:41:05 Miner compile time: Mon Dec 26 19:16:16 CST 2022 type: Antminer BHB42XXX sn :
2023-11-23 07:41:06 This is fix-freq version
2023-11-23 07:41:06 Miner compile time: Mon Dec 26 19:16:16 CST 2022 type: Antminer BHB42XXX
2023-11-23 07:41:06 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 19:26:44
2023-11-23 07:41:06 opt_multi_version     = 1
2023-11-23 07:41:06 opt_bitmain_ab        = 1
2023-11-23 07:41:06 mid_auto_gen          = 1
2023-11-23 07:41:06 opt_bitmain_work_mode = 0
2023-11-23 07:41:06 port 439 already exported
2023-11-23 07:41:06 port 454 already exported
2023-11-23 07:41:06 port 440 already exported
2023-11-23 07:41:06 port 455 already exported
2023-11-23 07:41:06 port 441 already exported
2023-11-23 07:41:06 port 456 already exported
2023-11-23 07:41:06 port 438 already exported
2023-11-23 07:41:06 port 453 already exported
2023-11-23 07:41:06 port 446 already exported
2023-11-23 07:41:06 port 445 already exported
2023-11-23 07:41:06 Note: front fan is power on!
2023-11-23 07:41:06 Note: rear fan is power on!
2023-11-23 07:41:06 start the http log.
2023-11-23 07:41:06 httpListenThread start ret=0
2023-11-23 07:41:06 start listen on 6060 ...
2023-11-23 07:41:06 bad chain id = 3
2023-11-23 07:41:09 bad chain id = 3
2023-11-23 07:41:11 ==========================capability start==========================
2023-11-23 07:41:11 board num = 3
2023-11-23 07:41:11 board id = 0, chain num = 1
2023-11-23 07:41:11 	chain id = 0
2023-11-23 07:41:11 board id = 1, chain num = 1
2023-11-23 07:41:11 	chain id = 1
2023-11-23 07:41:11 board id = 2, chain num = 1
2023-11-23 07:41:11 	chain id = 2
2023-11-23 07:41:11 ==========================capability end============================
2023-11-23 07:41:11 chain num = 3
2023-11-23 07:41:11 skip loading levels for now
2023-11-23 07:41:15 load chain 0 eeprom data
2023-11-23 07:41:18 load chain 1 eeprom data
2023-11-23 07:41:22 load chain 2 eeprom data
2023-11-23 07:41:22 i2c_sim_init start
2023-11-23 07:41:22 init gpio477
2023-11-23 07:41:22 init gpio476
2023-11-23 07:41:22 i2c_sim_init end
2023-11-23 07:41:23 power open power_version = 0x71
2023-11-23 07:41:29 power is not Calibrated
2023-11-23 07:41:30 miner type: Antminer S19j Pro
2023-11-23 07:41:30 multi machine mode
2023-11-23 07:41:30 load machine BHB42601 conf
2023-11-23 07:41:30 machine : BHB42601 
2023-11-23 07:41:30 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-11-23 07:41:30 abandon mix board!
2023-11-23 07:41:30 abandon mix board!
2023-11-23 07:41:30 fan_eft : 0  fan_pwm : 100
2023-11-23 07:41:30 create thread get_nonce_and_register_thread
2023-11-23 07:41:30 fixed working voltage = 1360
2023-11-23 07:41:30 fixed frequency is 545
2023-11-23 07:41:30 Chain [0] PCB Version: 0x0130
2023-11-23 07:41:30 Chain [0] BOM Version: 0x0010
2023-11-23 07:41:30 Chain [1] PCB Version: 0x0130
2023-11-23 07:41:30 Chain [1] BOM Version: 0x0010
2023-11-23 07:41:30 Chain [2] PCB Version: 0x0130
2023-11-23 07:41:30 Chain [2] BOM Version: 0x0010
2023-11-23 07:41:30 bad chain id = 3
2023-11-23 07:41:30 Fan check passed.
2023-11-23 07:41:30 uart_trans addr:0xf41df000.
2023-11-23 07:41:31 chain[0] PIC jump to app
2023-11-23 07:41:32 Check chain[0] PIC fw version=0x89
2023-11-23 07:41:33 chain[1] PIC jump to app
2023-11-23 07:41:35 Check chain[1] PIC fw version=0x89
2023-11-23 07:41:36 chain[2] PIC jump to app
2023-11-23 07:41:37 Check chain[2] PIC fw version=0x89
2023-11-23 07:41:38 create thread pic_heart_beat_thread
2023-11-23 07:41:38 max sensor num = 4
2023-11-23 07:41:38 STATUS_INITED: soc init done!
2023-11-23 07:41:38 temperature_monitor_thread start...
2023-11-23 07:41:38 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2023-11-23 07:41:38 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2023-11-23 07:41:39 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2023-11-23 07:41:39 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2023-11-23 07:41:39 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2023-11-23 07:41:39 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2023-11-23 07:41:40 start to init...
2023-11-23 07:41:40 warning:power is not calibration.
2023-11-23 07:41:40 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2023-11-23 07:41:40 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2023-11-23 07:41:41 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2023-11-23 07:41:41 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2023-11-23 07:41:41 power type version: 0x0071
2023-11-23 07:41:41 Initializing the power, please wait, this may take up to 2 minutes...
2023-11-23 07:41:41 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2023-11-23 07:41:41 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2023-11-23 07:41:42 over max temp, pcb temp 10 (max 75), chip temp 255(max 95) pcb temp rise 0 chip temp rise 0, total_exit_failure 6
2023-11-23 07:41:42 Sweep error string = J0:6.
2023-11-23 07:41:42 ERROR_TEMP_TOO_HIGH: over max temp
2023-11-23 07:41:42 stop_mining: over max temp
2023-11-23 07:41:42 uninit_temp_info
2023-11-23 07:41:42 do not read temp anymore...
2023-11-23 07:41:42 cancel thread
2023-11-23 07:41:42 cancel thread
2023-11-23 07:41:42 ****power off hashboard****
2023-11-23 07:41:46 temp monitor thread exit
2023-11-23 07:42:02 Version num 65536
2023-11-23 07:42:02 Mask num 0x1fffe000
2023-11-23 07:42:02 opt_multi_version = 65536, interval timeout = 2837042
2023-11-23 07:42:02 freq = 545, percent = 90, hcn = 4809, timeout = 2837042
2023-11-23 07:44:42 Slept 180 seconds, diff = 10.
2023-11-23 07:44:42 set_voltage_by_steps to 1500.
2023-11-23 07:44:46 start up min temp by 75a = 0
2023-11-23 07:44:56 Chain[0]: find 0 asic, times 0
2023-11-23 07:45:07 Chain[0]: find 0 asic, times 1
2015-01-01 00:00:15 Open miner sn file /config/sn error
2015-01-01 00:00:15 Miner compile time: Mon Dec 26 19:16:16 CST 2022 type: Antminer BHB42XXX sn :
2015-01-01 00:00:16 This is fix-freq version
2015-01-01 00:00:16 Miner compile time: Mon Dec 26 19:16:16 CST 2022 type: Antminer

015-01-01 00:00:15 Open miner sn file /config/sn error
2015-01-01 00:00:15 Miner compile time: Mon Dec 26 19:16:16 CST 2022 type: Antminer BHB42XXX sn :
2015-01-01 00:00:16 This is fix-freq version
2015-01-01 00:00:16 Miner compile time: Mon Dec 26 19:16:16 CST 2022 type: Antminer BHB42XXX
2015-01-01 00:00:16 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 19:26:44
2015-01-01 00:00:16 opt_multi_version = 1
2015-01-01 00:00:16 opt_bitmain_ab = 1
2015-01-01 00:00:16 mid_auto_gen = 1
2015-01-01 00:00:16 opt_bitmain_work_mode = 0
2015-01-01 00:00:16 port 439 already exported
2015-01-01 00:00:16 port 454 already exported
2015-01-01 00:00:16 port 440 already exported
2015-01-01 00:00:16 port 455 already exported
2015-01-01 00:00:16 port 441 already exported
2015-01-01 00:00:16 port 456 already exported
2015-01-01 00:00:16 port 438 already exported
2015-01-01 00:00:16 port 453 already exported
2015-01-01 00:00:16 port 446 already exported
2015-01-01 00:00:16 port 445 already exported
2015-01-01 00:00:16 Note: front fan is power on!
2015-01-01 00:00:16 Note: rear fan is power on!
2015-01-01 00:00:16 start the http log.
2015-01-01 00:00:16 httpListenThread start ret=0
2015-01-01 00:00:16 start listen on 6060 ...
2015-01-01 00:00:16 bad chain id = 3
2015-01-01 00:00:19 bad chain id = 3
2015-01-01 00:00:21 ==========================capability start==========================
2015-01-01 00:00:21 board num = 3
2015-01-01 00:00:21 board id = 0, chain num = 1
2015-01-01 00:00:21 chain id = 0
2015-01-01 00:00:21 board id = 1, chain num = 1
2015-01-01 00:00:21 chain id = 1
2015-01-01 00:00:21 board id = 2, chain num = 1
2015-01-01 00:00:21 chain id = 2
2015-01-01 00:00:21 ==========================capability end============================
2015-01-01 00:00:21 chain num = 3
2015-01-01 00:00:21 skip loading levels for now
2015-01-01 00:00:25 load chain 0 eeprom data
2015-01-01 00:00:28 load chain 1 eeprom data
2024-02-29 14:10:50 load chain 2 eeprom data
2024-02-29 14:10:50 i2c_sim_init start
2024-02-29 14:10:50 init gpio477
2024-02-29 14:10:50 init gpio476
2024-02-29 14:10:50 i2c_sim_init end
2024-02-29 14:10:51 power open power_version = 0x71
2024-02-29 14:10:54 power is not Calibrated
2024-02-29 14:10:55 miner type: Antminer S19j Pro
2024-02-29 14:10:55 multi machine mode
2024-02-29 14:10:55 load machine BHB42601 conf
2024-02-29 14:10:55 machine : BHB42601
2024-02-29 14:10:55 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2024-02-29 14:10:55 abandon mix board!
2024-02-29 14:10:55 abandon mix board!
2024-02-29 14:10:55 fan_eft : 0 fan_pwm : 100
2024-02-29 14:10:55 create thread get_nonce_and_register_thread
2024-02-29 14:10:55 fixed working voltage = 1360
2024-02-29 14:10:55 fixed frequency is 545
2024-02-29 14:10:55 Chain [0] PCB Version: 0x0130
2024-02-29 14:10:55 Chain [0] BOM Version: 0x0010
2024-02-29 14:10:55 Chain [1] PCB Version: 0x0130
2024-02-29 14:10:55 Chain [1] BOM Version: 0x0010
2024-02-29 14:10:55 Chain [2] PCB Version: 0x0130
2024-02-29 14:10:55 Chain [2] BOM Version: 0x0010
2024-02-29 14:10:55 bad chain id = 3
2024-02-29 14:10:55 Fan check passed.
2024-02-29 14:10:55 uart_trans addr:0xf7048000.
2024-02-29 14:10:56 chain[0] PIC jump to app
2024-02-29 14:10:57 Check chain[0] PIC fw version=0x89
2024-02-29 14:10:59 chain[1] PIC jump to app
2024-02-29 14:11:00 Check chain[1] PIC fw version=0x89
2024-02-29 14:11:01 chain[2] PIC jump to app
2024-02-29 14:11:03 Check chain[2] PIC fw version=0x89
2024-02-29 14:11:03 create thread pic_heart_beat_thread
2024-02-29 14:11:03 max sensor num = 4
2024-02-29 14:11:03 STATUS_INITED: soc init done!
2024-02-29 14:11:03 temperature_monitor_thread start...
2024-02-29 14:11:03 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2024-02-29 14:11:03 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2024-02-29 14:11:04 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2024-02-29 14:11:04 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2024-02-29 14:11:05 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2024-02-29 14:11:05 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2024-02-29 14:11:05 start to init...
2024-02-29 14:11:05 warning:power is not calibration.
2024-02-29 14:11:06 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2024-02-29 14:11:06 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2024-02-29 14:11:06 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2024-02-29 14:11:06 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2024-02-29 14:11:06 power type version: 0x0071
2024-02-29 14:11:06 Initializing the power, please wait, this may take up to 2 minutes...
2024-02-29 14:11:07 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2024-02-29 14:11:07 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2024-02-29 14:11:07 over max temp, pcb temp 24 (max 75), chip temp 255(max 95) pcb temp rise 0 chip temp rise 0, total_exit_failure 6
2024-02-29 14:11:07 Sweep error string = J0:6.
2024-02-29 14:11:07 ERROR_TEMP_TOO_HIGH: over max temp
2024-02-29 14:11:07 stop_mining: over max temp
2024-02-29 14:11:07 uninit_temp_info
2024-02-29 14:11:07 do not read temp anymore...
2024-02-29 14:11:07 cancel thread
2024-02-29 14:11:07 cancel thread
2024-02-29 14:11:07 ****power off hashboard****
2024-02-29 14:11:11 temp monitor thread exit
2024-02-29 14:11:31 Version num 65536
2024-02-29 14:11:31 Mask num 0x1fffe000
2024-02-29 14:11:31 opt_multi_version = 65536, interval timeout = 2837042
2024-02-29 14:11:31 freq = 545, percent = 90, hcn = 4809, timeout = 2837042
2024-02-29 14:14:07 Slept 180 seconds, diff = 24.
2024-02-29 14:14:07 set_voltage_by_steps to 1500.
2024-02-29 14:14:11 power voltage can not meet the target
2024-02-29 14:14:12 power voltage can not meet the target
2024-02-29 14:14:14 power voltage can not meet the target
2024-02-29 14:14:14 Sweep error string = V:1.
2024-02-29 14:14:14 ERROR_POWER_LOST: get power type version failed!
2024-02-29 14:14:14 stop_mining: get power type version failed!
2024-02-29 14:14:14 ****power off hashboard****
2024-02-29 14:14:18 ERROR_SOC_INIT: soc init failed!
2024-02-29 14:14:18 stop_mining: soc init failed!
2024-02-29 14:14:18 ****power off hashboard****
2015-01-01 00:00:15 Open miner sn file /config/sn error
2015-01-01 00:00:15 Miner compile time: Mon Dec 26 19:16:16 CST 2022 type: Antminer BHB42XXX sn :
2015-01-01 00:00:16 This is fix-freq version
2015-01-01 00:00:16 Miner compile time: Mon Dec 26 19:16:16 CST 2022 type: Antminer BHB42XXX
2015-01-01 00:00:16 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 19:26:44
2015-01-01 00:00:16 opt_multi_version = 1
2015-01-01 00:00:16 opt_bitmain_ab = 1
2015-01-01 00:00:16 mid_auto_gen = 1
2015-01-01 00:00:16 opt_bitmain_work_mode = 0
2015-01-01 00:00:16 port 439 already exported
2015-01-01 00:00:16 port 454 already exported
2015-01-01 00:00:16 port 440 already exported
2015-01-01 00:00:16 port 455 already exported
2015-01-01 00:00:16 no board pluged in socket 440
2015-01-01 00:00:16 port 441 already exported
2015-01-01 00:00:16 port 456 already exported
2015-01-01 00:00:16 port 438 already exported
2015-01-01 00:00:16 port 453 already exported
2015-01-01 00:00:16 port 446 already exported
2015-01-01 00:00:16 port 445 already exported
2015-01-01 00:00:16 Note: front fan is power on!
2015-01-01 00:00:16 Note: rear fan is power on!
2015-01-01 00:00:16 start the http log.
2015-01-01 00:00:16 httpListenThread start ret=0
2015-01-01 00:00:16 start listen on 6060 ...
2015-01-01 00:00:16 bad chain id = 3
2015-01-01 00:00:19 bad chain id = 3
2015-01-01 00:00:21 ==========================capability start==========================
2015-01-01 00:00:21 board num = 2
2015-01-01 00:00:21 board id = 0, chain num = 1
2015-01-01 00:00:21 chain id = 0
2015-01-01 00:00:21 board id = 2, chain num = 1
2015-01-01 00:00:21 chain id = 2
2015-01-01 00:00:21 ==========================capability end============================
2015-01-01 00:00:21 chain num = 2
2015-01-01 00:00:21 skip loading levels for now
2015-01-01 00:00:25 load chain 0 eeprom data
2024-02-29 14:18:53 load chain 2 eeprom data
2024-02-29 14:18:53 i2c_sim_init start
2024-02-29 14:18:53 init gpio477
2024-02-29 14:18:53 init gpio476
2024-02-29 14:18:53 i2c_sim_init end
2024-02-29 14:18:54 power open power_version = 0x71
2024-02-29 14:19:03 power is not Calibrated
2024-02-29 14:19:04 miner type: Antminer S19j Pro
2024-02-29 14:19:04 multi machine mode
2024-02-29 14:19:04 load machine BHB42601 conf
2024-02-29 14:19:04 machine : BHB42601
2024-02-29 14:19:04 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2024-02-29 14:19:04 abandon mix board!
2024-02-29 14:19:04 abandon mix board!
2024-02-29 14:19:04 fan_eft : 0 fan_pwm : 100
2024-02-29 14:19:04 create thread get_nonce_and_register_thread
2024-02-29 14:19:04 fixed working voltage = 1360
2024-02-29 14:19:04 failed to load freq in eeprom, using default
2024-02-29 14:19:04 fixed frequency is 200
2024-02-29 14:19:04 Chain [0] PCB Version: 0x0130
2024-02-29 14:19:04 Chain [0] BOM Version: 0x0010
2024-02-29 14:19:04 Chain [2] PCB Version: 0x0130
2024-02-29 14:19:04 Chain [2] BOM Version: 0x0010
2024-02-29 14:19:04 bad chain id = 3
2024-02-29 14:19:04 Fan check passed.
2024-02-29 14:19:04 uart_trans addr:0xf74a6000.
2024-02-29 14:19:05 chain[0] PIC jump to app
2024-02-29 14:19:06 Check chain[0] PIC fw version=0x89
2024-02-29 14:19:07 chain[2] PIC jump to app
2024-02-29 14:19:09 Check chain[2] PIC fw version=0x89
2024-02-29 14:19:09 create thread pic_heart_beat_thread
2024-02-29 14:19:09 max sensor num = 4
2024-02-29 14:19:09 STATUS_INITED: soc init done!
2024-02-29 14:19:09 temperature_monitor_thread start...
2024-02-29 14:19:09 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2024-02-29 14:19:09 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2024-02-29 14:19:10 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2024-02-29 14:19:10 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2024-02-29 14:19:10 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2024-02-29 14:19:10 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2024-02-29 14:19:11 _pic_write_iic failed! read_back_data[0] = 0x3b, read_back_data[1] = 0x00
2024-02-29 14:19:11 pic_read_iic: select slave: 0x48, reg/command: 0x00 is failed
2024-02-29 14:19:11 over max temp, pcb temp 24 (max 75), chip temp 255(max 95) pcb temp rise 0 chip temp rise 0, total_exit_failure 4
2024-02-29 14:19:11 Sweep error string = J0:6.
2024-02-29 14:19:11 ERROR_TEMP_TOO_HIGH: over max temp
2024-02-29 14:19:11 stop_mining: over max temp
2024-02-29 14:19:11 uninit_temp_info
2024-02-29 14:19:11 do not read temp anymore...
2024-02-29 14:19:11 cancel thread
2024-02-29 14:19:11 cancel thread
2024-02-29 14:19:11 ****power off hashboard****
2024-02-29 14:19:12 start to init...
2024-02-29 14:19:12 warning:power is not calibration.
2024-02-29 14:19:12 Version num 65536
2024-02-29 14:19:12 Mask num 0x1fffe000
2024-02-29 14:19:12 opt_multi_version = 65536, interval timeout = 7730940
2024-02-29 14:19:12 freq = 200, percent = 90, hcn = 13107, timeout = 7730940
2024-02-29 14:19:13 power type version: 0x0071
2024-02-29 14:19:13 Initializing the power, please wait, this may take up to 2 minutes...
2024-02-29 14:19:15 temp monitor thread exit
2015-01-01 00:00:15 Open miner sn file /config/sn error
2015-01-01 00:00:15 Miner compile time: Mon Dec 26 19:16:16 CST 2022 type: Antminer BHB42XXX sn :
2015-01-01 00:00:16 This is fix-freq version
2015-01-01 00:00:16 Miner compile time: Mon Dec 26 19:16:16 CST 2022 type: Antminer BHB42XXX
2015-01-01 00:00:16 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 19:26:44
2015-01-01 00:00:16 opt_multi_version = 1
2015-01-01 00:00:16 opt_bitmain_ab = 1
2015-01-01 00:00:16 mid_auto_gen = 1
2015-01-01 00:00:16 opt_bitmain_work_mode = 0
2015-01-01 00:00:16 port 439 already exported
2015-01-01 00:00:16 port 454 already exported
2015-01-01 00:00:16 port 440 already exported
2015-01-01 00:00:16 port 455 already exported
2015-01-01 00:00:16 port 441 already exported
2015-01-01 00:00:16 port 456 already exported
2015-01-01 00:00:16 no board pluged in socket 441
2015-01-01 00:00:16 port 438 already exported
2015-01-01 00:00:16 port 453 already exported
2015-01-01 00:00:16 port 446 already exported
2015-01-01 00:00:16 port 445 already exported
2015-01-01 00:00:16 Note: front fan is power on!
2015-01-01 00:00:16 Note: rear fan is power on!
2015-01-01 00:00:16 start the http log.
2015-01-01 00:00:16 httpListenThread start ret=0
2015-01-01 00:00:16 start listen on 6060 ...
2015-01-01 00:00:16 bad chain id = 3
2015-01-01 00:00:19 bad chain id = 3
2015-01-01 00:00:21 ==========================capability start==========================
2015-01-01 00:00:21 board num = 2
2015-01-01 00:00:21 board id = 0, chain num = 1
2015-01-01 00:00:21 chain id = 0
2015-01-01 00:00:21 board id = 1, chain num = 1
2015-01-01 00:00:21 chain id = 1
2015-01-01 00:00:21 ==========================capability end============================
2015-01-01 00:00:21 chain num = 2
2015-01-01 00:00:21 skip loading levels for now
2015-01-01 00:00:25 load chain 0 eeprom data
2024-02-29 14:21:54 load chain 1 eeprom data
2024-02-29 14:21:54 i2c_sim_init start
2024-02-29 14:21:54 init gpio477
2024-02-29 14:21:54 init gpio476
2024-02-29 14:21:54 i2c_sim_init end
2024-02-29 14:21:55 power open power_version = 0x71
2024-02-29 14:21:58 power is not Calibrated
2024-02-29 14:21:59 miner type: Antminer S19j Pro
2024-02-29 14:21:59 multi machine mode
2024-02-29 14:21:59 load machine BHB42601 conf
2024-02-29 14:21:59 machine : BHB42601
2024-02-29 14:21:59 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2024-02-29 14:21:59 abandon mix board!
2024-02-29 14:21:59 abandon mix board!
2024-02-29 14:21:59 fan_eft : 0 fan_pwm : 100
2024-02-29 14:21:59 create thread get_nonce_and_register_thread
2024-02-29 14:21:59 fixed working voltage = 1360
2024-02-29 14:21:59 failed to load freq in eeprom, using default
2024-02-29 14:21:59 fixed frequency is 200
2024-02-29 14:21:59 Chain [0] PCB Version: 0x0130
2024-02-29 14:21:59 Chain [0] BOM Version: 0x0010
2024-02-29 14:21:59 Chain [1] PCB Version: 0x0130
2024-02-29 14:21:59 Chain [1] BOM Version: 0x0010
2024-02-29 14:21:59 bad chain id = 3
2024-02-29 14:21:59 Fan check passed.
2024-02-29 14:21:59 uart_trans addr:0xf7508000.
2024-02-29 14:22:00 chain[0] PIC jump to app
2024-02-29 14:22:01 Check chain[0] PIC fw version=0x89
2024-02-29 14:22:02 chain[1] PIC jump to app
2024-02-29 14:22:04 Check chain[1] PIC fw version=0x89
2024-02-29 14:22:04 create thread pic_heart_beat_thread
2024-02-29 14:22:04 max sensor num = 4
2024-02-29 14:22:04 STATUS_INITED: soc init done!
2024-02-29 14:22:04 temperature_monitor_thread start...
2024-02-29 14:22:07 start to init...
2024-02-29 14:22:07 warning:power is not calibration.
2024-02-29 14:22:08 power type version: 0x0071
2024-02-29 14:22:08 Initializing the power, please wait, this may take up to 2 minutes...
2024-02-29 14:22:39 Slept 30 seconds, diff = 1.
2024-02-29 14:22:39 set_voltage_by_steps to 1500.
2024-02-29 14:22:43 power voltage can not meet the target
2024-02-29 14:22:45 power voltage can not meet the target
2024-02-29 14:22:46 power voltage can not meet the target
2024-02-29 14:22:46 Sweep error string = V:1.
2024-02-29 14:22:46 ERROR_POWER_LOST: get power type version failed!
2024-02-29 14:22:46 stop_mining: get power type version failed!
2024-02-29 14:22:46 uninit_temp_info
2024-02-29 14:22:46 do not read temp anymore...
2024-02-29 14:22:46 cancel thread
2024-02-29 14:22:46 cancel thread
2024-02-29 14:22:46 ****power off hashboard****
2024-02-29 14:22:46 temp monitor thread exit
2024-02-29 14:22:47 Version num 65536
2024-02-29 14:22:47 Mask num 0x1fffe000
2024-02-29 14:22:47 opt_multi_version = 65536, interval timeout = 7730940
2024-02-29 14:22:47 freq = 200, percent = 90, hcn = 13107, timeout = 7730940
2024-02-29 14:22:49 ERROR_SOC_INIT: soc init failed!
2024-02-29 14:22:49 stop_mining: soc init failed!
2024-02-29 14:22:49 ****power off hashboard****
2015-01-01 00:00:15 Open miner sn file /config/sn error
2015-01-01 00:00:15 Miner compile time: Mon Dec 26 19:16:16 CST 2022 type: Antminer BHB42XXX sn :
2015-01-01 00:00:16 This is fix-freq version
2015-01-01 00:00:16 Miner compile time: Mon Dec 26 19:16:16 CST 2022 type: Antminer BHB42XXX
2015-01-01 00:00:16 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 19:26:44
2015-01-01 00:00:16 opt_multi_version = 1
2015-01-01 00:00:16 opt_bitmain_ab = 1
2015-01-01 00:00:16 mid_auto_gen = 1
2015-01-01 00:00:16 opt_bitmain_work_mode = 0
2015-01-01 00:00:16 port 439 already exported
2015-01-01 00:00:16 port 454 already exported
2015-01-01 00:00:16 no board pluged in socket 439
2015-01-01 00:00:16 port 440 already exported
2015-01-01 00:00:16 port 455 already exported
2015-01-01 00:00:16 port 441 already exported
2015-01-01 00:00:16 port 456 already exported
2015-01-01 00:00:16 port 438 already exported
2015-01-01 00:00:16 port 453 already exported
2015-01-01 00:00:16 port 446 already exported
2015-01-01 00:00:16 port 445 already exported
2015-01-01 00:00:16 Note: front fan is power on!
2015-01-01 00:00:16 Note: rear fan is power on!
2015-01-01 00:00:16 start the http log.
2015-01-01 00:00:16 httpListenThread start ret=0
2015-01-01 00:00:16 start listen on 6060 ...
2015-01-01 00:00:16 bad chain id = 3
2015-01-01 00:00:19 bad chain id = 3
2015-01-01 00:00:21 ==========================capability start==========================
2015-01-01 00:00:21 board num = 2
2015-01-01 00:00:21 board id = 1, chain num = 1
2015-01-01 00:00:21 chain id = 1
2015-01-01 00:00:21 board id = 2, chain num = 1
2015-01-01 00:00:21 chain id = 2
2015-01-01 00:00:21 ==========================capability end============================
2015-01-01 00:00:21 chain num = 2
2015-01-01 00:00:21 skip loading levels for now
2015-01-01 00:00:25 load chain 1 eeprom data
2015-01-01 00:00:28 load chain 2 eeprom data
2015-01-01 00:00:28 i2c_sim_init start
2015-01-01 00:00:28 init gpio477
2015-01-01 00:00:28 init gpio476
2015-01-01 00:00:28 i2c_sim_init end
2024-02-29 14:26:49 power open power_version = 0x71
2024-02-29 14:26:52 power is not Calibrated
2024-02-29 14:26:53 miner type: Antminer S19j Pro
2024-02-29 14:26:53 multi machine mode
2024-02-29 14:26:53 load machine BHB42601 conf
2024-02-29 14:26:53 machine : BHB42601
2024-02-29 14:26:53 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2024-02-29 14:26:53 abandon mix board!
2024-02-29 14:26:53 abandon mix board!
2024-02-29 14:26:53 fan_eft : 0 fan_pwm : 100
2024-02-29 14:26:53 create thread get_nonce_and_register_thread
2024-02-29 14:26:53 fixed working voltage = 1360
2024-02-29 14:26:53 failed to load freq in eeprom, using default
2024-02-29 14:26:53 fixed frequency is 200
2024-02-29 14:26:53 Chain [1] PCB Version: 0x0130
2024-02-29 14:26:53 Chain [1] BOM Version: 0x0010
2024-02-29 14:26:53 Chain [2] PCB Version: 0x0130
2024-02-29 14:26:53 Chain [2] BOM Version: 0x0010
2024-02-29 14:26:53 bad chain id = 3
2024-02-29 14:26:53 Fan check passed.
2024-02-29 14:26:53 uart_trans addr:0xf72cc000.
2024-02-29 14:26:54 chain[1] PIC jump to app
2024-02-29 14:26:55 Check chain[1] PIC fw version=0x89
2024-02-29 14:26:56 chain[2] PIC jump to app
2024-02-29 14:26:58 Check chain[2] PIC fw version=0x89
2024-02-29 14:26:58 create thread pic_heart_beat_thread
2024-02-29 14:26:58 max sensor num = 4
2024-02-29 14:26:58 STATUS_INITED: soc init done!
2024-02-29 14:26:58 temperature_monitor_thread start...
2024-02-29 14:26:58 _pic_wri

Comments

5 comments

Jay

March 21, 2024 02:14
Hello sir
Log shows temperature sensor failure
Don’t you know how to repair it yourself? ? Do you have maintenance equipment? ?
If you need technical support
Please contact me (whatsapp: +8619123969124
From Zeus Mining
0

Comment actions Permalink
Nick

March 21, 2024 03:38
Dear Customer,
If you have any questions please feel free to contact us.
Please send email to customersupport@bitmain.com
We will reply to your question as soon as possible.
0

Comment actions Permalink
Rosen Antonov Markov

March 22, 2024 12:44
Hello , after I run the miner with 2 hashboards only , this is the current log that I have :

[ 0.000000@0] Booting Linux on physical CPU 0x0

[ 0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Mon Dec 26 19:33:19 CST 2022

[ 0.000000@0] Boot CPU: AArch64 Processor [410fd034]

[ 0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '')

[ 0.000000@0] bootconsole [aml_uart0] enabled

[ 0.000000@0] efi: Getting EFI parameters from FDT:

[ 0.000000@0] efi: UEFI not found.

[ 0.000000@0] 07400000 - 07500000, 1024 KB, ramoops@0x07400000

[ 0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB

[ 0.000000@0] 05000000 - 05400000, 4096 KB, linux,secmon

[ 0.000000@0] __reserved_mem_alloc_size, start:0x000000003e000000, end:0x0000000040000000, len:32 MiB

[ 0.000000@0] failed to allocate memory for node linux,meson-fb, size:32 MB

[ 0.000000@0] cma: Reserved 16 MiB at 0x000000000f000000

[ 0.000000@0] On node 0 totalpages: 65536

[ 0.000000@0] DMA zone: 1024 pages used for memmap

[ 0.000000@0] DMA zone: 0 pages reserved

[ 0.000000@0] DMA zone: 65536 pages, LIFO batch:15

[ 0.000000@0] psci: probing for conduit method from DT.

[ 0.000000@0] psci: PSCIv1.0 detected in firmware.

[ 0.000000@0] psci: Using standard PSCI v0.2 function IDs

[ 0.000000@0] psci: MIGRATE_INFO_TYPE not supported.

[ 0.000000@0] psci: SMC Calling Convention v1.1

[ 0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00ef53000 s64536 r8192 d29672 u102400

[ 0.000000@0] pcpu-alloc: s64536 r8192 d29672 u102400 alloc=25*4096

[ 0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3

[ 0.000000@0] Detected VIPT I-cache on CPU0

[ 0.000000@0] CPU features: enabling workaround for ARM erratum 845719

[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64512

[ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 androidboot.rpmb_state=0 rootfstype=ramfs init=/sbin/init

[ 0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes)

[ 0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)

[ 0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)

[ 0.000000@0] Memory: 211688K/262144K available (8764K kernel code, 1194K rwdata, 2424K rodata, 3648K init, 1017K bss, 29976K reserved, 20480K cma-reserved)

[ 0.000000@0] Virtual kernel memory layout:

[ 0.000000@0] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)

[ 0.000000@0] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)

[ 0.000000@0] .text : 0xffffff8009080000 - 0xffffff8009910000 ( 8768 KB)

[ 0.000000@0] .rodata : 0xffffff8009910000 - 0xffffff8009b80000 ( 2496 KB)

[ 0.000000@0] .init : 0xffffff8009b80000 - 0xffffff8009f10000 ( 3648 KB)

[ 0.000000@0] .data : 0xffffff8009f10000 - 0xffffff800a03aa00 ( 1195 KB)

[ 0.000000@0] .bss : 0xffffff800a03aa00 - 0xffffff800a139034 ( 1018 KB)

[ 0.000000@0] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB)

[ 0.000000@0] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)

[ 0.000000@0] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)

[ 0.000000@0] 0xffffffbf00000000 - 0xffffffbf00400000 ( 4 MB actual)

[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc010000000 ( 256 MB)

[ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1

[ 0.000000@0] Preemptible hierarchical RCU implementation.

[ 0.000000@0] Build-time adjustment of leaf fanout to 64.

[ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.

[ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4

[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0

[ 0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized

[ 0.000000@0] axg_aoclkc_init: register ao clk ok!

[ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk

[ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk

[ 0.000000@0] axg_amlogic_init_media: register meson media clk

[ 0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks

[ 0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk

[ 0.000000@0] axg_clkc_init initialization complete

[ 0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).

[ 0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns

[ 0.000003@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns

[ 0.008252@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194

[ 0.016898@0] Console: colour dummy device 80x25

[ 0.021106@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)

[ 0.031586@0] pid_max: default: 32768 minimum: 301

[ 0.036436@0] thread_stack_cache_init, vmap:ffffffc00e5af600, bitmap:ffffffc00e5a3000, cache page:e5e0

[ 0.045772@0] thread_stack_cache_init, allocation vm area:ffffffc00e5d94c0, addr:ffffff8020000000, size:20001000

[ 0.056005@0] cpu 0, vmap_stack:[ffffffc00ef5c960-ffffffc00ef60950]

[ 0.062304@0] cpu 0, irq_stack: [ffffffc00ef53060-ffffffc00ef57050]

[ 0.068604@0] cpu 1, vmap_stack:[ffffffc00ef75960-ffffffc00ef79950]

[ 0.074904@0] cpu 1, irq_stack: [ffffffc00ef6c060-ffffffc00ef70050]

[ 0.081204@0] cpu 2, vmap_stack:[ffffffc00ef8e960-ffffffc00ef92950]

[ 0.087504@0] cpu 2, irq_stack: [ffffffc00ef85060-ffffffc00ef89050]

[ 0.093804@0] cpu 3, vmap_stack:[ffffffc00efa7960-ffffffc00efab950]

[ 0.100104@0] cpu 3, irq_stack: [ffffffc00ef9e060-ffffffc00efa2050]

[ 0.106464@0] Security Framework initialized

[ 0.110696@0] SELinux: Initializing.

[ 0.114388@0] SELinux: Starting in permissive mode

[ 0.114425@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

[ 0.121108@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)

[ 0.128833@0] ftrace: allocating 30061 entries in 118 pages

[ 0.186522@0] sched-energy: CPU device node has no sched-energy-costs

[ 0.187331@0] CPU0: update cpu_capacity 1024

[ 0.191657@0] ASID allocator initialised with 32768 entries

[ 0.229794@0] secmon: can't fine clear_range

[ 0.229996@0] EFI services will not be available.

[ 0.233263@0] Meson chip version = RevC (25:C - 23:0)

[ 0.266939@1] Detected VIPT I-cache on CPU1

[ 0.266999@1] CPU1: update cpu_capacity 1024

[ 0.267002@1] CPU1: Booted secondary processor [410fd034]

[ 0.295000@2] Detected VIPT I-cache on CPU2

[ 0.295053@2] CPU2: update cpu_capacity 1024

[ 0.295055@2] CPU2: Booted secondary processor [410fd034]

[ 0.323058@3] Detected VIPT I-cache on CPU3

[ 0.323107@3] CPU3: update cpu_capacity 1024

[ 0.323109@3] CPU3: Booted secondary processor [410fd034]

[ 0.323198@0] Brought up 4 CPUs

[ 0.362416@0] SMP: Total of 4 processors activated.

[ 0.367326@0] CPU features: detected feature: 32-bit EL0 Support

[ 0.373361@0] CPU features: detected feature: Kernel page table isolation (KPTI)

[ 0.383919@0] CPU: All CPU(s) started at EL2

[ 0.385101@0] alternatives: patching kernel code

[ 0.390407@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755

[ 0.397626@0] devtmpfs: initialized

[ 0.412643@0] DMI not present or invalid.

[ 0.413040@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns

[ 0.421011@0] futex hash table entries: 1024 (order: 4, 65536 bytes)

[ 0.427588@0] pinctrl core: initialized pinctrl subsystem

[ 0.433962@0] NET: Registered protocol family 16

[ 0.457537@0] cpuidle: using governor menu

[ 0.458046@0] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000)

[ 0.463650@0] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers.

[ 0.471060@0] DMA: preallocated 256 KiB pool for atomic allocations

[ 0.477182@0] clkmsr: clkmsr: driver init

[ 0.481251@0] aml_watch_point_probe, in, wp:2

[ 0.486687@0] pstore: using zlib compression

[ 0.490092@0] console [pstore-1] enabled

[ 0.493527@0] pstore: Registered ramoops as persistent store backend

[ 0.499936@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0

[ 0.514277@0] aml_iomap: amlogic iomap probe done

[ 0.521130@0] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c

[ 0.523068@0] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0

[ 0.619276@0] usbcore: registered new interface driver usbfs

[ 0.619446@0] usbcore: registered new interface driver hub

[ 0.625160@0] usbcore: registered new device driver usb

[ 0.630348@0] pps_core: LinuxPPS API ver. 1 registered

[ 0.635284@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>

[ 0.644672@0] PTP clock support registered

[ 0.649016@0] dmi: Firmware registration failed.

[ 0.657818@0] secmon: reserve_mem_size:0x300000

[ 0.657990@0] secmon secmon: assigned reserved memory node linux,secmon

[ 0.664972@0] secmon: get page:ffffffbf00140000, 5000

[ 0.669648@0] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000

[ 0.678035@0] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000

[ 0.685920@0] NetLabel: Initializing

[ 0.688085@0] NetLabel: domain hash size = 128

[ 0.692669@0] NetLabel: protocols = UNLABELED CIPSOv4

[ 0.697902@0] NetLabel: unlabeled traffic allowed by default

[ 0.704539@0] clocksource: Switched to clocksource arch_sys_counter

[ 0.831402@0] VFS: Disk quotas dquot_6.6.0

[ 0.831550@0] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)

[ 0.857287@0] NET: Registered protocol family 2

[ 0.858354@0] TCP established hash table entries: 2048 (order: 2, 16384 bytes)

[ 0.863538@0] TCP bind hash table entries: 2048 (order: 3, 32768 bytes)

[ 0.870185@0] TCP: Hash tables configured (established 2048 bind 2048)

[ 0.876782@0] UDP hash table entries: 256 (order: 1, 8192 bytes)

[ 0.882738@0] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)

[ 0.889489@0] NET: Registered protocol family 1

[ 0.894482@0] RPC: Registered named UNIX socket transport module.

[ 0.899888@0] RPC: Registered udp transport module.

[ 0.904761@0] RPC: Registered tcp transport module.

[ 0.909671@0] RPC: Registered tcp NFSv4.1 backchannel transport module.

[ 0.918799@0] Unpacking initramfs...

[ 1.419476@0] Initramfs unpacking failed: junk in compressed archive

[ 1.426273@0] Freeing initrd memory: 6572K

[ 1.427202@0] hw perfevents: clusterb_enabled = 0

[ 1.429507@0] hw perfevents: cpumasks 0xf, 0x0

[ 1.433991@0] hw perfevents: cluster A irq = 7

[ 1.438561@0] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available

[ 1.448703@0] audit: initializing netlink subsys (disabled)

[ 1.452013@0] audit: type=2000 audit(1.264:1): initialized

[ 1.459303@0] workingset: timestamp_bits=62 max_order=16 bucket_order=0

[ 1.483422@0] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[ 1.486366@0] NFS: Registering the id_resolver key type

[ 1.489134@0] Key type id_resolver registered

[ 1.493459@0] Key type id_legacy registered

[ 1.498112@0] fuse init (API version 7.26)

[ 1.503478@0] SELinux: Registering netfilter hooks

[ 1.509645@0] NET: Registered protocol family 38

[ 1.509704@0] Key type asymmetric registered

[ 1.512957@0] Asymmetric key parser 'x509' registered

[ 1.518423@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)

[ 1.525650@0] io scheduler noop registered (default)

[ 1.530706@0] io scheduler deadline registered

[ 1.535414@0] io scheduler cfq registered

[ 1.555765@1] random: fast init done

[ 1.555863@1] random: crng init done

[ 1.556303@0] Unable to detect cache hierarchy for CPU 0

[ 1.592711@0] loop: module loaded

[ 1.594232@0] zram: Added device: zram0

[ 1.594634@0] mtdoops: mtd device (mtddev=name/number) must be supplied

[ 1.601572@0] libphy: Fixed MDIO Bus: probed

[ 1.606036@0] tun: Universal TUN/TAP device driver, 1.6

[ 1.610457@0] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>

[ 1.618660@0] ee eth reset:Addr = ffffff80081fd008

[ 1.626147@0] meson6-dwmac ff3f0000.ethernet: no reset control found

[ 1.628099@0] stmmac - user ID: 0x11, Synopsys ID: 0x37

[ 1.633381@0] Ring mode enabled

[ 1.636596@0] DMA HW capability register supported

[ 1.641328@0] Normal descriptors

[ 1.644643@0] RX Checksum Offload Engine supported

[ 1.649552@0] COE Type 2

[ 1.652153@0] TX Checksum insertion supported

[ 1.656632@0] Wake-Up On Lan supported

[ 1.660577@0] Enable RX Mitigation via HW Watchdog Timer

[ 1.674135@0] libphy: stmmac: probed

[ 1.674189@0] eth%d: PHY ID 0007c0f1 at 0 IRQ POLL (stmmac-0:00) active

[ 1.680696@0] PPP generic driver version 2.4.2

[ 1.683575@0] PPP BSD Compression module registered

[ 1.688136@0] PPP Deflate Compression module registered

[ 1.693390@0] PPP MPPE Compression module registered

[ 1.698342@0] NET: Registered protocol family 24

[ 1.703825@0] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[ 1.709748@0] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

[ 1.716811@0] usbcore: registered new interface driver cdc_acm

[ 1.721991@0] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters

[ 1.730397@0] usbcore: registered new interface driver usbserial

[ 1.737133@0] mousedev: PS/2 mouse device common for all mice

[ 1.742541@0] usbcore: registered new interface driver xpad

[ 1.747920@0] i2c /dev entries driver

[ 1.752740@0] cpu cpu0: bL_cpufreq_init: CPU 0 initialized

[ 1.756939@0] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi

[ 1.767829@0] ff803000.serial: clock gate not found

[ 1.769496@0] meson_uart ff803000.serial: ==uart0 reg addr = ffffff800830d000

[ 1.776681@0] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 13, base_baud = 1500000) is a meson_uart

[ 1.791597@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200

[ 1.794300@0] console [ttyS0] enabled

[ 1.801534@0] bootconsole [aml_uart0] disabled

[ 1.811180@3] ff804000.serial: clock gate not found

[ 1.815312@3] meson_uart ff804000.serial: ==uart3 reg addr = ffffff8008321000

[ 1.822436@3] ff804000.serial: ttyS3 at MMIO 0xff804000 (irq = 14, base_baud = 1500000) is a meson_uart

[ 1.832825@2] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff8008323000

[ 1.838914@2] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 25, base_baud = 1500000) is a meson_uart

[ 1.849113@0] meson_uart ffd23000.serial: ==uart2 reg addr = ffffff8008325000

[ 1.855380@0] ffd23000.serial: ttyS2 at MMIO 0xffd23000 (irq = 26, base_baud = 1500000) is a meson_uart

[ 1.866292@3] amlogic-new-usb2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff8008348000

[ 1.875651@3] amlogic-new-usb3 ffe09080.usb3phy: This phy has no usb port

[ 1.882128@3] amlogic-new-usb3 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff800834c080

[ 1.897288@3] i2c i2c-1: of_i2c: modalias failure on /soc/aobus@ff800000/i2c@5000/mcu6350@40

[ 1.900954@3] i2c i2c-1: Failed to create I2C device for /soc/aobus@ff800000/i2c@5000/mcu6350@40

[ 1.913307@3] aml_dma ff63e000.aml_dma: Aml dma

[ 1.916350@3] aml_aes_dma ff63e000.aml_dma:aml_aes: Aml AES_dma

[ 1.921475@3] aml_sha_dma ff63e000.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma

[ 1.927852@3] efusekeynum: 4

[ 1.930186@3] efusekeyname: mac offset: 0 size: 6

[ 1.936573@3] efusekeyname: mac_bt offset: 6 size: 6

[ 1.942995@3] efusekeyname: mac_wifi offset: 12 size: 6

[ 1.949401@3] efusekeyname: usid offset: 18 size: 16

[ 1.956283@1] efuse efuse: probe OK!

[ 1.961772@1] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller

[ 1.968947@1] meson-mmc: >>>>>>>>hostbase ffffff8008358000, dmode

[ 1.974024@1] meson-mmc: actual_clock :400000, HHI_nand: 0x80

[ 1.979214@1] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c

[ 2.024679@1] meson-mmc: meson_mmc_probe() : success!

[ 2.024932@1] amlogic mtd driver init

[ 2.028994@1] prase_get_dtb_nand_parameter:128,parse dts start

[ 2.033752@1] bl mode descrete

[ 2.036632@1] fip_copies 4

[ 2.039296@1] fip_size 0x200000

[ 2.042435@1] nand_clk_ctrl 0xffe07000

[ 2.046159@1] prase_get_dtb_nand_parameter:234,parse dts end

[ 2.051826@1] nand_clk_ctrl 0xffe07000

[ 2.055548@1] nand register base ffffff80083df800, nand clock register ffffff80083e1000

[ 2.064285@1] plat->aml_nand_device ffffff800a005c10

[ 2.068476@1] m3_nand_probe() aml_nand_device ffffff800a005c10

[ 2.074522@1] NAND device id: 2c da 90 95 6 0

[ 2.078584@1] NAND device: Manufacturer ID:

[ 2.082648@1] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)

[ 2.089691@1] oob_fill_cnt =32 oob_size =64, bch_bytes =14

[ 2.095125@1] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16

[ 2.100673@1] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1

[ 2.106919@1] mtd->oobavail: 0x8

[ 2.110312@1] aml_nand_init 2119: plat-name:bootloader

[ 2.115238@1] Creating 1 MTD partitions on "bootloader":

[ 2.120541@1] 0x000000000000-0x000000200000 : "bootloader"

[ 2.129297@0] bootloader initialized ok

[ 2.129785@0] plat->aml_nand_device ffffff800a005c10

[ 2.134763@0] m3_nand_probe() aml_nand_device ffffff800a005c10

[ 2.140902@0] NAND device id: 2c da 90 95 6 0

[ 2.144925@0] NAND device: Manufacturer ID:

[ 2.148951@0] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)

[ 2.155994@0] oob_fill_cnt =32 oob_size =64, bch_bytes =14

[ 2.161427@0] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16

[ 2.166980@0] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1

[ 2.173221@0] mtd->oobavail: 0x8

[ 2.176650@0] aml_nand_init 2119: plat-name:nandnormal

[ 2.181591@0] bbt_start=20

[ 2.184199@0] env_start=24

[ 2.186914@0] key_start=32

[ 2.189593@0] dtb_start=40

[ 2.192259@0] ddr_start=44

[ 2.194967@0] nbbt: info size=0x800 max_scan_blk=24, start_blk=20

[ 2.201468@0] get_free_node 43: bitmap=0

[ 2.204935@0] get_free_node 55: bitmap=1

[ 2.209025@0] get_free_node 43: bitmap=1

[ 2.212732@0] get_free_node 55: bitmap=3

[ 2.216824@0] get_free_node 43: bitmap=3

[ 2.220514@0] get_free_node 55: bitmap=7

[ 2.224416@0] nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1

[ 2.231103@0] nbbt free list:

[ 2.234051@0] blockN=21, ec=-1, dirty_flag=0

[ 2.238297@0] blockN=22, ec=-1, dirty_flag=0

[ 2.242544@0] blockN=23, ec=-1, dirty_flag=0

[ 2.246791@0] aml_nand_scan_rsv_info 1141: page_num=1

[ 2.252200@0] nbbt valid addr: 280000

[ 2.255458@0] aml_nand_bbt_check 1306 bbt is valid, reading.

[ 2.261093@0] aml_nand_read_rsv_info:423,read nbbt info at 280000

[ 2.267353@0] nenv: info size=0x10000 max_scan_blk=32, start_blk=24

[ 2.273780@0] get_free_node 43: bitmap=7

[ 2.277299@0] get_free_node 55: bitmap=f

[ 2.281390@0] get_free_node 43: bitmap=f

[ 2.285099@0] get_free_node 55: bitmap=1f

[ 2.289276@0] get_free_node 43: bitmap=1f

[ 2.293072@0] get_free_node 55: bitmap=3f

[ 2.297250@0] get_free_node 43: bitmap=3f

[ 2.301045@0] get_free_node 55: bitmap=7f

[ 2.305223@0] get_free_node 43: bitmap=7f

[ 2.309019@0] get_free_node 55: bitmap=ff

[ 2.313197@0] get_free_node 43: bitmap=ff

[ 2.316992@0] get_free_node 55: bitmap=1ff

[ 2.321256@0] get_free_node 43: bitmap=1ff

[ 2.325139@0] get_free_node 55: bitmap=3ff

[ 2.329212@0] nenv : phy_blk_addr=24, ec=0, phy_page_addr=0, timestamp=1

[ 2.335883@0] nenv free list:

[ 2.338830@0] blockN=25, ec=-1, dirty_flag=0

[ 2.343077@0] blockN=26, ec=-1, dirty_flag=0

[ 2.347324@0] blockN=27, ec=-1, dirty_flag=0

[ 2.351570@0] blockN=28, ec=-1, dirty_flag=0

[ 2.355817@0] blockN=29, ec=-1, dirty_flag=0

[ 2.360063@0] blockN=30, ec=-1, dirty_flag=0

[ 2.364310@0] blockN=31, ec=-1, dirty_flag=0

[ 2.368557@0] aml_nand_scan_rsv_info 1141: page_num=32

[ 2.385791@0] nenv valid addr: 310000

[ 2.385824@0] nkey: info size=0x8000 max_scan_blk=40, start_blk=32

[ 2.390183@0] get_free_node 43: bitmap=3ff

[ 2.394065@0] get_free_node 55: bitmap=7ff

[ 2.398329@0] get_free_node 43: bitmap=7ff

[ 2.402212@0] get_free_node 55: bitmap=fff

[ 2.406476@0] get_free_node 43: bitmap=fff

[ 2.410358@0] get_free_node 55: bitmap=1fff

[ 2.414709@0] get_free_node 43: bitmap=1fff

[ 2.418679@0] get_free_node 55: bitmap=3fff

[ 2.423029@0] get_free_node 43: bitmap=3fff

[ 2.426999@0] get_free_node 55: bitmap=7fff

[ 2.431350@0] get_free_node 43: bitmap=7fff

[ 2.435318@0] get_free_node 55: bitmap=ffff

[ 2.439669@0] get_free_node 43: bitmap=ffff

[ 2.443638@0] get_free_node 55: bitmap=1ffff

[ 2.448076@0] get_free_node 43: bitmap=1ffff

[ 2.452129@0] get_free_node 55: bitmap=3ffff

[ 2.456378@0] nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0

[ 2.463056@0] nkey free list:

[ 2.465997@0] blockN=32, ec=-1, dirty_flag=0

[ 2.470243@0] blockN=33, ec=-1, dirty_flag=0

[ 2.474490@0] blockN=34, ec=-1, dirty_flag=0

[ 2.478736@0] blockN=35, ec=-1, dirty_flag=0

[ 2.482982@0] blockN=36, ec=-1, dirty_flag=0

[ 2.487229@0] blockN=37, ec=-1, dirty_flag=0

[ 2.491476@0] blockN=38, ec=-1, dirty_flag=0

[ 2.495722@0] blockN=39, ec=-1, dirty_flag=0

[ 2.499970@0] aml_nand_scan_rsv_info 1141: page_num=16

[ 2.505083@0] nkey valid addr: fffffffffffe0000

[ 2.509590@0] aml_nand_key_check 1251 NO key exist

[ 2.514358@0] ndtb: info size=0x20000 max_scan_blk=44, start_blk=40

[ 2.520980@0] get_free_node 43: bitmap=3ffff

[ 2.524845@0] get_free_node 55: bitmap=7ffff

[ 2.529282@0] get_free_node 43: bitmap=7ffff

[ 2.533338@0] get_free_node 55: bitmap=fffff

[ 2.537776@0] get_free_node 43: bitmap=fffff

[ 2.541831@0] get_free_node 55: bitmap=1fffff

[ 2.546165@0] ndtb : phy_blk_addr=40, ec=0, phy_page_addr=0, timestamp=1

[ 2.552835@0] ndtb free list:

[ 2.555766@0] blockN=41, ec=-1, dirty_flag=0

[ 2.560029@0] blockN=42, ec=-1, dirty_flag=0

[ 2.564276@0] blockN=43, ec=-1, dirty_flag=0

[ 2.568533@0] aml_nand_scan_rsv_info 1141: page_num=64

[ 2.585765@0] ndtb valid addr: 500000

[ 2.585799@0] nddr: info size=0x20000 max_scan_blk=46, start_blk=44

[ 2.590246@0] get_free_node 43: bitmap=1fffff

[ 2.594387@0] get_free_node 55: bitmap=3fffff

[ 2.598911@0] get_free_node 43: bitmap=3fffff

[ 2.603053@0] get_free_node 55: bitmap=7fffff

[ 2.607386@0] nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0

[ 2.614057@0] nddr free list:

[ 2.617004@0] blockN=44, ec=-1, dirty_flag=0

[ 2.621250@0] blockN=45, ec=-1, dirty_flag=0

[ 2.625497@0] aml_nand_scan_rsv_info 1141: page_num=64

[ 2.630610@0] nddr valid addr: fffffffffffe0000

[ 2.635118@0] aml_nand_ddr_check 1281 NO ddr exist

[ 2.639888@0] tpl: off 8388608, size 8388608

[ 2.771715@0] Creating 6 MTD partitions on "nandnormal":

[ 2.771763@0] 0x000000800000-0x000001000000 : "tpl"

[ 2.782797@3] 0x000001000000-0x000001200000 : "misc"

[ 2.785877@2] 0x000001200000-0x000002200000 : "recovery"

[ 2.798031@3] 0x000002200000-0x000004200000 : "boot"

[ 2.817190@3] 0x000004200000-0x000004700000 : "config"

[ 2.821804@3] 0x000004700000-0x000010000000 : "nvdata"

[ 2.922633@0] nandnormal initialized ok

[ 2.922742@0] aml_ubootenv_init: register env chardev

[ 2.926500@0] aml_ubootenv_init: register env chardev OK

[ 2.931320@0] amlnf_dtb_init: register dtb cdev

[ 2.936070@2] amlnf_dtb_init: register dtd cdev OK

[ 2.940491@2] mtd_nand_probe 267 , err = 0

[ 2.945932@0] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc0

[ 2.951058@0] input: aml_vkeypad as /devices/platform/rtc/input/input0

[ 2.958065@3] unifykey: storage in base: 0xffffffc005000000

[ 2.962702@3] unifykey: storage out base: 0xffffffc005040000

[ 2.968295@3] unifykey: storage block base: 0xffffffc005080000

[ 2.974097@3] unifykey: probe done!

[ 2.978284@3] unifykey: no efuse-version set, use default value: -1

[ 2.983810@3] unifykey: key unify config unifykey-num is 6

[ 2.989325@3] unifykey: key unify fact unifykey-num is 6

[ 2.994546@3] unifykey: unifykey_devno: f200000

[ 2.999520@2] unifykey: device unifykeys created ok

[ 3.004027@2] unifykey: aml_unifykeys_init done!

[ 3.008966@2] sysled: module init

[ 3.012364@2] meson_wdt ffd0f0d0.watchdog: start watchdog

[ 3.017182@2] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog

[ 3.024650@1] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done

[ 3.033307@0] dmc_monitor_probe

[ 3.034953@0] defendkey defendkey: Reserved memory is not enough!

[ 3.039925@0] defendkey: probe of defendkey failed with error -22

[ 3.046260@0] GACT probability NOT on

[ 3.049610@0] Mirror/redirect action on

[ 3.053410@0] u32 classifier

[ 3.056222@0] Actions configured

[ 3.059813@0] Netfilter messages via NETLINK v0.30.

[ 3.065074@0] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)

[ 3.071280@0] ctnetlink v0.93: registering with nfnetlink.

[ 3.077163@0] xt_time: kernel timezone is -0000

[ 3.080867@0] ipip: IPv4 and MPLS over IPv4 tunneling driver

[ 3.087506@0] ip_tables: (C) 2000-2006 Netfilter Core Team

[ 3.092171@0] arp_tables: arp_tables: (C) 2002 David S. Miller

[ 3.097703@0] Initializing XFRM netlink socket

[ 3.103206@0] NET: Registered protocol family 10

[ 3.108961@0] mip6: Mobile IPv6

[ 3.109746@0] ip6_tables: (C) 2000-2006 Netfilter Core Team

[ 3.115716@0] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver

[ 3.123709@0] NET: Registered protocol family 17

[ 3.126013@0] NET: Registered protocol family 15

[ 3.130597@0] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.

[ 3.143749@0] l2tp_core: L2TP core driver, V2.0

[ 3.148134@0] l2tp_ppp: PPPoL2TP kernel driver, V2.0

[ 3.153050@0] l2tp_ip: L2TP IP encapsulation support (L2TPv3)

[ 3.158804@0] l2tp_netlink: L2TP netlink interface

[ 3.163605@0] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)

[ 3.169675@0] l2tp_debugfs: L2TP debugfs support

[ 3.174195@0] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)

[ 3.180858@0] NET: Registered protocol family 35

[ 3.185768@0] Key type dns_resolver registered

[ 3.190370@0] Registered swp emulation handler

[ 3.194237@0] Registered cp15_barrier emulation handler

[ 3.199429@0] Registered setend emulation handler

[ 3.204171@0] disable EAS feature

[ 3.208788@0] registered taskstats version 1

[ 3.225358@3] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host

[ 3.731780@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller

[ 3.731868@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1

[ 3.740154@3] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f664 hci version 0x100 quirks 0x02010010

[ 3.748616@3] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0xff500000

[ 3.756028@1] hub 1-0:1.0: USB hub found

[ 3.758551@1] hub 1-0:1.0: 1 port detected

[ 3.763157@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller

[ 3.768173@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2

[ 3.776070@1] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.

[ 3.785557@2] hub 2-0:1.0: USB hub found

[ 3.788126@2] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)

[ 3.795469@2] usb usb2: Unsupported the hub

[ 3.800204@2] aml_vrtc rtc: setting system clock to 2024-03-22 09:19:47 UTC (1711099187)

[ 3.808293@2] dwc_otg ff400000.dwc2_a: dwc_otg_driver_probe(ffffffc00d17f000)

[ 3.808369@2] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0

[ 3.816249@2] dwc_otg ff400000.dwc2_a: base=0xffffff8008580000

[ 3.816261@2] dwc_otg ff400000.dwc2_a: dwc_otg_device=0xffffffc00bb20800

[ 3.916889@2] dwc_otg: Core Release: 3.10a

[ 3.916946@2] dwc_otg: Setting default values for core params

[ 3.921123@2] dwc_otg: curmode: 0, host_only: 0

[ 3.925640@2] dwc_otg ff400000.dwc2_a: DMA config: BURST_DEFAULT

[ 3.938148@2] dwc_otg: Using Buffer DMA mode

[ 3.938185@2] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1

[ 3.942087@2] dwc_otg: Working on port type = SLAVE

[ 3.946944@2] dwc_otg: Dedicated Tx FIFOs mode

[ 3.953939@2] thermal thermal_zone0: binding zone soc_thermal with cdev thermal-cpufreq-0 failed:-22

[ 3.960677@2] cpucore_cooling_register, max_cpu_core_num:4

[ 3.972878@0] gxbb_pm: enter meson_pm_probe!

[ 3.972936@0] no vddio3v3_en pin

[ 3.974589@0] pm-meson aml_pm: Can't get switch_clk81

[ 3.979710@0] gxbb_pm: meson_pm_probe done

[ 3.984653@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200

[ 3.990908@0] Freeing unused kernel memory: 3648K

[ 4.005298@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200

[ 4.264862@0] ubi0: attaching mtd5

[ 4.283419@0] ubi0: scanning is finished

[ 4.288100@2] ubi0: attached mtd5 (name "config", size 5 MiB)

[ 4.288226@2] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes

[ 4.295277@2] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048

[ 4.302200@2] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096

[ 4.309296@2] ubi0: good PEBs: 40, bad PEBs: 0, corrupted PEBs: 0

[ 4.315370@2] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128

[ 4.322737@2] ubi0: max/mean erase counter: 17/8, WL threshold: 4096, image sequence number: 1319742140

[ 4.332097@2] ubi0: available PEBs: 0, total reserved PEBs: 40, PEBs reserved for bad PEB handling: 4

[ 4.341302@0] ubi0: background thread "ubi_bgt0d" started, PID 1075

[ 4.354304@1] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 1079

[ 4.395008@3] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "config_data"

[ 4.397442@3] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes

[ 4.407467@3] UBIFS (ubi0:0): FS size: 2793472 bytes (2 MiB, 22 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)

[ 4.417684@3] UBIFS (ubi0:0): reserved for root: 131942 bytes (128 KiB)

[ 4.424271@3] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID AC4140A2-9971-4056-8324-4D2ABD53A465, small LPT model

[ 4.448640@0] ubi2: attaching mtd6

[ 5.123777@2] ubi2: scanning is finished

[ 5.131024@0] ubi2: attached mtd6 (name "nvdata", size 185 MiB)

[ 5.131328@0] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes

[ 5.138382@0] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048

[ 5.145352@0] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096

[ 5.152399@0] ubi2: good PEBs: 1480, bad PEBs: 0, corrupted PEBs: 0

[ 5.158646@0] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128

[ 5.166005@0] ubi2: max/mean erase counter: 296/119, WL threshold: 4096, image sequence number: 3799898847

[ 5.175632@0] ubi2: available PEBs: 0, total reserved PEBs: 1480, PEBs reserved for bad PEB handling: 4

[ 5.185010@3] ubi2: background thread "ubi_bgt2d" started, PID 1087

[ 5.197742@1] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 1091

[ 5.235319@2] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "nvdata_data"

[ 5.237750@2] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes

[ 5.247783@2] UBIFS (ubi2:0): FS size: 185384960 bytes (176 MiB, 1460 LEBs), journal size 9269248 bytes (8 MiB, 73 LEBs)

[ 5.258603@2] UBIFS (ubi2:0): reserved for root: 4952683 bytes (4836 KiB)

[ 5.265373@2] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID C352C475-F90D-4F5E-9B99-94DB2DA9F359, small LPT model

[ 5.490339@0] eth0: device MAC address 02:af:61:85:fc:c0

[ 5.573362@3] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP.

[ 5.574671@3] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

[ 5.817844@1] uart_trans: loading out-of-tree module taints kernel.

[ 5.820447@1] register uart_trans chrdev success.

[ 5.823773@1] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 0 to 9600

[ 5.831370@1] tty port open success [/dev/ttyS3]!

[ 5.835906@1] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 9600 to 115200

[ 5.844314@1] init sucess for tty struct (246:3) [/dev/ttyS3]

[ 5.850467@1] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 0 to 9600

[ 5.858099@1] tty port open success [/dev/ttyS2]!

[ 5.862802@1] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 9600 to 115200

[ 5.871183@1] init sucess for tty struct (246:2) [/dev/ttyS2]

[ 5.877293@1] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 0 to 9600

[ 5.884937@1] tty port open success [/dev/ttyS1]!

[ 5.889630@1] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 115200

[ 5.898020@1] init sucess for tty struct (246:1) [/dev/ttyS1]

[ 5.904299@3] create workqueue success!

[ 7.608890@3] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off

[ 7.611999@3] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

[ 28.966603@1] uart trans dev open.

[ 28.966716@1] uart_buf virt addr = 0xffffffc00b140000

[ 28.969468@1] uart_buf phys addr = 0x0b140000

[ 28.973771@1] uart_buf pfn = 0x0000b140

[ 28.978570@1] uart trans stop send work timer.

[ 28.982724@1] uart trans set chain exist bits:0x3.

[ 28.987325@1] uart trans set work queue count 768.

[ 127.399441@0] uart set baud to: 4098

[ 127.399501@0] uart set baud to: 4098

[ 155.291480@1] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 115200 to 3000000

[ 155.294675@1] uart set baud to: 4109

[ 155.358627@1] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 115200 to 3000000

[ 155.361757@1] uart set baud to: 4109

[ 202.492320@2] uart trans start send work timer.

===========================================Miner log===========================================

2024-03-22 09:19:54 Open miner sn file /config/sn error

2024-03-22 09:19:54 Miner compile time: Mon Dec 26 19:16:16 CST 2022 type: Antminer BHB42XXX sn :

2024-03-22 09:19:55 This is fix-freq version

2024-03-22 09:19:55 Miner compile time: Mon Dec 26 19:16:16 CST 2022 type: Antminer BHB42XXX

2024-03-22 09:19:55 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 19:26:44

2024-03-22 09:19:55 opt_multi_version = 1

2024-03-22 09:19:55 opt_bitmain_ab = 1

2024-03-22 09:19:55 mid_auto_gen = 1

2024-03-22 09:19:55 opt_bitmain_work_mode = 0

2024-03-22 09:19:55 port 439 already exported

2024-03-22 09:19:55 port 454 already exported

2024-03-22 09:19:55 port 440 already exported

2024-03-22 09:19:55 port 455 already exported

2024-03-22 09:19:55 port 441 already exported

2024-03-22 09:19:55 port 456 already exported

2024-03-22 09:19:55 no board pluged in socket 441

2024-03-22 09:19:55 port 438 already exported

2024-03-22 09:19:55 port 453 already exported

2024-03-22 09:19:55 port 446 already exported

2024-03-22 09:19:55 port 445 already exported

2024-03-22 09:19:55 Note: front fan is power on!

2024-03-22 09:19:55 Note: rear fan is power on!

2024-03-22 09:19:55 start the http log.

2024-03-22 09:19:55 httpListenThread start ret=0

2024-03-22 09:19:55 start listen on 6060 ...

2024-03-22 09:19:55 bad chain id = 3

2024-03-22 09:19:58 bad chain id = 3

2024-03-22 09:20:00 ==========================capability start==========================

2024-03-22 09:20:00 board num = 2

2024-03-22 09:20:00 board id = 0, chain num = 1

2024-03-22 09:20:00 chain id = 0

2024-03-22 09:20:00 board id = 1, chain num = 1

2024-03-22 09:20:00 chain id = 1

2024-03-22 09:20:00 ==========================capability end============================

2024-03-22 09:20:00 chain num = 2

2024-03-22 09:20:00 skip loading levels for now

2024-03-22 09:20:04 load chain 0 eeprom data

2024-03-22 09:20:07 load chain 1 eeprom data

2024-03-22 09:20:07 i2c_sim_init start

2024-03-22 09:20:07 init gpio477

2024-03-22 09:20:07 init gpio476

2024-03-22 09:20:07 i2c_sim_init end

2024-03-22 09:20:08 power open power_version = 0x71

2024-03-22 09:20:11 power is not Calibrated

2024-03-22 09:20:13 miner type: Antminer S19j Pro

2024-03-22 09:20:13 multi machine mode

2024-03-22 09:20:13 load machine BHB42601 conf

2024-03-22 09:20:13 machine : BHB42601

2024-03-22 09:20:13 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3

2024-03-22 09:20:13 abandon mix board!

2024-03-22 09:20:13 abandon mix board!

2024-03-22 09:20:13 fan_eft : 0 fan_pwm : 100

2024-03-22 09:20:13 create thread get_nonce_and_register_thread

2024-03-22 09:20:13 fixed working voltage = 1360

2024-03-22 09:20:13 failed to load freq in eeprom, using default

2024-03-22 09:20:13 fixed frequency is 200

2024-03-22 09:20:13 Chain [0] PCB Version: 0x0130

2024-03-22 09:20:13 Chain [0] BOM Version: 0x0010

2024-03-22 09:20:13 Chain [1] PCB Version: 0x0130

2024-03-22 09:20:13 Chain [1] BOM Version: 0x0010

2024-03-22 09:20:13 bad chain id = 3

2024-03-22 09:20:13 Fan check passed.

2024-03-22 09:20:13 uart_trans addr:0xf45df000.

2024-03-22 09:20:13 chain[0] PIC jump to app

2024-03-22 09:20:15 Check chain[0] PIC fw version=0x89

2024-03-22 09:20:16 chain[1] PIC jump to app

2024-03-22 09:20:17 Check chain[1] PIC fw version=0x89

2024-03-22 09:20:18 create thread pic_heart_beat_thread

2024-03-22 09:20:18 max sensor num = 4

2024-03-22 09:20:18 STATUS_INITED: soc init done!

2024-03-22 09:20:18 temperature_monitor_thread start...

2024-03-22 09:20:20 start to init...

2024-03-22 09:20:20 warning:power is not calibration.

2024-03-22 09:20:21 power type version: 0x0071

2024-03-22 09:20:21 Initializing the power, please wait, this may take up to 2 minutes...

2024-03-22 09:21:47 Slept 85 seconds, diff = 3.

2024-03-22 09:21:47 set_voltage_by_steps to 1500.

2024-03-22 09:21:49 chain avg vol rise to 15.16

2024-03-22 09:21:51 start up min temp by 75a = 27

2024-03-22 09:22:01 Chain[0]: find 126 asic, times 0

2024-03-22 09:22:11 Chain[1]: find 126 asic, times 0

2024-03-22 09:22:16 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1

2024-03-22 09:22:19 Bring up temperature is 27

2024-03-22 09:22:19 set UART baud to 3000000

2024-03-22 09:22:19 create thread check_miner_status_thread

2024-03-22 09:22:19 create thread check_system_work_thread

2024-03-22 09:22:19 set_voltage_by_steps to 1450.

2024-03-22 09:22:21 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1

2024-03-22 09:22:21 start do_core_reset

2024-03-22 09:22:34 end do_core_reset

2024-03-22 09:22:34 chain[0] min = 200 max =200

2024-03-22 09:22:34 chain[1] min = 200 max =200

2024-03-22 09:22:34 1.inc all chain freq to 200

2024-03-22 09:22:34 fixed step freq_start = 50, freq_end = 200, freq_step = 6.25

2024-03-22 09:22:34 chain = 0 set freq to 56.25

2024-03-22 09:22:34 chain = 1 set freq to 56.25

2024-03-22 09:22:34 chain = 0 set freq to 62.50

2024-03-22 09:22:34 chain = 1 set freq to 62.50

2024-03-22 09:22:35 chain = 0 set freq to 68.75

2024-03-22 09:22:35 chain = 1 set freq to 68.75

2024-03-22 09:22:35 chain = 0 set freq to 75.00

2024-03-22 09:22:35 chain = 1 set freq to 75.00

2024-03-22 09:22:35 chain = 0 set freq to 81.25

2024-03-22 09:22:35 chain = 1 set freq to 81.25

2024-03-22 09:22:36 chain = 0 set freq to 87.50

2024-03-22 09:22:36 chain = 1 set freq to 87.50

2024-03-22 09:22:36 chain = 0 set freq to 93.75

2024-03-22 09:22:36 chain = 1 set freq to 93.75

2024-03-22 09:22:36 chain = 0 set freq to 100.00

2024-03-22 09:22:36 chain = 1 set freq to 100.00

2024-03-22 09:22:37 chain = 0 set freq to 106.25

2024-03-22 09:22:37 chain = 1 set freq to 106.25

2024-03-22 09:22:37 chain = 0 set freq to 112.50

2024-03-22 09:22:37 chain = 1 set freq to 112.50

2024-03-22 09:22:37 chain = 0 set freq to 118.75

2024-03-22 09:22:37 chain = 1 set freq to 118.75

2024-03-22 09:22:37 chain = 0 set freq to 125.00

2024-03-22 09:22:37 chain = 1 set freq to 125.00

2024-03-22 09:22:38 chain = 0 set freq to 131.25

2024-03-22 09:22:38 chain = 1 set freq to 131.25

2024-03-22 09:22:38 chain = 0 set freq to 137.50

2024-03-22 09:22:38 chain = 1 set freq to 137.50

2024-03-22 09:22:38 chain = 0 set freq to 143.75

2024-03-22 09:22:38 chain = 1 set freq to 143.75

2024-03-22 09:22:39 chain = 0 set freq to 150.00

2024-03-22 09:22:39 chain = 1 set freq to 150.00

2024-03-22 09:22:39 chain = 0 set freq to 156.25

2024-03-22 09:22:39 chain = 1 set freq to 156.25

2024-03-22 09:22:39 chain = 0 set freq to 162.50

2024-03-22 09:22:39 chain = 1 set freq to 162.50

2024-03-22 09:22:40 chain = 0 set freq to 168.75

2024-03-22 09:22:40 chain = 1 set freq to 168.75

2024-03-22 09:22:40 chain = 0 set freq to 175.00

2024-03-22 09:22:40 chain = 1 set freq to 175.00

2024-03-22 09:22:40 chain = 0 set freq to 181.25

2024-03-22 09:22:40 chain = 1 set freq to 181.25

2024-03-22 09:22:41 chain = 0 set freq to 187.50

2024-03-22 09:22:41 chain = 1 set freq to 187.50

2024-03-22 09:22:41 chain = 0 set freq to 193.75

2024-03-22 09:22:41 chain = 1 set freq to 193.75

2024-03-22 09:22:41 chain = 0 set freq to 200.00

2024-03-22 09:22:41 chain = 1 set freq to 200.00

2024-03-22 09:22:41 enter mixed freq cfg

The miner is mining with 25-30T hashrates , I cannot understand why !

Should I send the faulty hashboard back to you for repair ?

If the miner is working with the other 2 hashboards , does that mean the problem is in the other hashboard ?

All the best
0

Comment actions Permalink
Nick

March 23, 2024 03:24
Dear customer.

From the kernel log, it can't detect the hashboard. please kindly exclude the issue by following steps:

1.Check the wires for the hashboard--pull them and re-plug them again, and also you can try to change the new wires.

2.Please clean up the dust.

How To Clean and Dust The Antminers

https://support.bitmain.com/hc/en-us/articles/115004520173-How-To-Clean-and-Dust-The-Antminers

3.Reset the miner to the factory settings

https://support.bitmain.com/hc/en-us/articles/115003595387-How-to-reset-miner-to-factory-settings-

If there are still the same problems after the above steps, please send it to repair.

Best regards

BITMAIN
0

Comment actions Permalink
Nick

March 23, 2024 03:24
Dear Customer,
If you have any questions please feel free to contact us.
Please send email to customersupport@bitmain.com
We will reply to your question as soon as possible.
0

Comment actions Permalink

Please sign in to leave a comment.

Comments

Didn't find what you were looking for?