Abnormal Hashrate Of S19 90th

Follow
Rajveer Singh

please help me, suddenly my s19 machine hashrate went to abnormal state.

This is my error log, please help me

2023-07-30 18:12:05 load chain 0 eeprom data
2023-07-30 18:12:08 load chain 1 eeprom data
2023-07-30 18:12:11 load chain 2 eeprom data
2023-07-30 18:12:11 miner type: Antminer S19
2023-07-30 18:12:11 multi machine mode
2023-07-30 18:12:11 load machine BHB42841 conf
2023-07-30 18:12:11 machine : BHB42841 
2023-07-30 18:12:11 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-07-30 18:12:11 abandon mix board!
2023-07-30 18:12:11 abandon mix board!
2023-07-30 18:12:12 fan_eft : 0  fan_pwm : 100
2023-07-30 18:12:12 create thread get_nonce_and_register_thread
2023-07-30 18:12:12 fixed working voltage = 1480
2023-07-30 18:12:12 fixed frequency is 475
2023-07-30 18:12:12 Chain [0] PCB Version: 0x0130
2023-07-30 18:12:12 Chain [0] BOM Version: 0x0010
2023-07-30 18:12:12 Chain [1] PCB Version: 0x0130
2023-07-30 18:12:12 Chain [1] BOM Version: 0x0010
2023-07-30 18:12:12 Chain [2] PCB Version: 0x0130
2023-07-30 18:12:12 Chain [2] BOM Version: 0x0010
2023-07-30 18:12:12 bad chain id = 3
2023-07-30 18:12:12 Fan check passed.
2023-07-30 18:12:12 uart_trans addr:0xf705a000.
2023-07-30 18:12:12 max sensor num = 4
2023-07-30 18:12:12 STATUS_INITED: soc init done!
2023-07-30 18:12:12 temperature_monitor_thread start...
2023-07-30 18:12:15 start to init...
2023-07-30 18:12:15 i2c_sim_init start
2023-07-30 18:12:15 init gpio477
2023-07-30 18:12:15 init gpio476
2023-07-30 18:12:15 i2c_sim_init end
2023-07-30 18:12:16 power open power_version = 0x75
2023-07-30 18:12:19 power is not Calibrated
2023-07-30 18:12:19 warning:power is not calibration.
2023-07-30 18:12:20 power type version: 0x0075
2023-07-30 18:12:22 disable power watchdog: 0x0000
2023-07-30 18:12:23 Initializing the power, please wait, this may take up to 2 minutes...
2023-07-30 18:12:41 reload pool, need recalculate
2023-07-30 18:12:41 set_start_time_point total_tv_start_sys=57 total_tv_end_sys=58
2023-07-30 18:12:54 Slept 30 seconds, diff = 1.
2023-07-30 18:12:57 set_voltage_by_steps to 1500.
2023-07-30 18:13:07 start up min temp by 75a = 28
2023-07-30 18:13:10 Chain[0]: find 126 asic, times 0
2023-07-30 18:13:12 Chain[1]: find 126 asic, times 0
2023-07-30 18:13:14 Chain[2]: find 0 asic, times 0
2023-07-30 18:13:15 Chain[2]: find 0 asic, times 1
2023-07-30 18:13:17 Chain[2]: find 0 asic, times 2
2023-07-30 18:13:17 Chain 2 only find 0 asic, will power off hash board 2
2023-07-30 18:13:17 ERROR_SOC_INIT: soc init failed!
2023-07-30 18:13:17 stop_mining: soc init failed!
2023-07-30 18:13:17 uninit_temp_info
2023-07-30 18:13:17 do not read temp anymore...
2023-07-30 18:13:17 cancel thread
2023-07-30 18:13:17 ****power off hashboard****
2023-07-30 18:13:18 temp monitor thread exit
2023-07-30 18:13:20 Version num 65536
2023-07-30 18:13:20 Mask num 0x1fffe000
2023-07-30 18:13:20 opt_multi_version = 65536, interval timeout = 3255132
2023-07-30 18:13:20 freq = 475, percent = 90, hcn = 5518, timeout = 3255132
2023-07-30 18:14:08 ****power off hashboard****
2023-07-30 18:14:13 Open miner sn file /config/sn error
2023-07-30 18:14:13 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer S19 sn :
2023-07-30 18:14:14 This is fix-freq version
2023-07-30 18:14:14 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer S19
2023-07-30 18:14:14 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 17:22:17
2023-07-30 18:14:14 opt_multi_version     = 1
2023-07-30 18:14:14 opt_bitmain_ab        = 1
2023-07-30 18:14:14 mid_auto_gen          = 1
2023-07-30 18:14:14 opt_bitmain_work_mode = 3
2023-07-30 18:14:14 port 439 already exported
2023-07-30 18:14:14 port 454 already exported
2023-07-30 18:14:14 port 440 already exported
2023-07-30 18:14:14 port 455 already exported
2023-07-30 18:14:14 port 441 already exported
2023-07-30 18:14:14 port 456 already exported
2023-07-30 18:14:14 port 438 already exported
2023-07-30 18:14:14 port 453 already exported
2023-07-30 18:14:14 port 446 already exported
2023-07-30 18:14:14 port 445 already exported
2023-07-30 18:14:14 Note: front fan is power on!
2023-07-30 18:14:14 Note: rear fan is power on!
2023-07-30 18:14:14 start the http log.
2023-07-30 18:14:14 httpListenThread start ret=0
2023-07-30 18:14:14 start listen on 6060 ...
2023-07-30 18:14:14 bad chain id = 3
2023-07-30 18:14:17 bad chain id = 3
2023-07-30 18:14:19 ==========================capability start==========================
2023-07-30 18:14:19 board num = 3
2023-07-30 18:14:19 board id = 0, chain num = 1
2023-07-30 18:14:19 	chain id = 0
2023-07-30 18:14:19 board id = 1, chain num = 1
2023-07-30 18:14:19 	chain id = 1
2023-07-30 18:14:19 board id = 2, chain num = 1
2023-07-30 18:14:19 	chain id = 2
2023-07-30 18:14:19 ==========================capability end============================
2023-07-30 18:14:19 chain num = 3
2023-07-30 18:14:19 skip loading levels for now
2023-07-30 18:14:22 load chain 0 eeprom data
2023-07-30 18:14:26 load chain 1 eeprom data
2023-07-30 18:14:29 load chain 2 eeprom data
2023-07-30 18:14:29 multi machine mode
2023-07-30 18:14:29 load machine BHB42841 conf
2023-07-30 18:14:29 machine : BHB42841 
2023-07-30 18:14:29 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-07-30 18:14:29 abandon mix board!
2023-07-30 18:14:29 abandon mix board!
2023-07-30 18:14:29 fan_eft : 0  fan_pwm : 100
2023-07-30 18:14:29 create thread get_nonce_and_register_thread
2023-07-30 18:14:29 fixed working voltage = 1480
2023-07-30 18:14:29 fixed frequency is 475
2023-07-30 18:14:29 Chain [0] PCB Version: 0x0130
2023-07-30 18:14:29 Chain [0] BOM Version: 0x0010
2023-07-30 18:14:29 Chain [1] PCB Version: 0x0130
2023-07-30 18:14:29 Chain [1] BOM Version: 0x0010
2023-07-30 18:14:29 Chain [2] PCB Version: 0x0130
2023-07-30 18:14:29 Chain [2] BOM Version: 0x0010
2023-07-30 18:14:29 bad chain id = 3
2023-07-30 18:14:29 Fan check passed.
2023-07-30 18:14:29 uart_trans addr:0xf721a000.
2023-07-30 18:14:29 max sensor num = 4
2023-07-30 18:14:29 STATUS_INITED: soc init done!
2023-07-30 18:14:29 temperature_monitor_thread start...
2023-07-30 18:14:31 start to init...
2023-07-30 18:14:31 i2c_sim_init start
2023-07-30 18:14:31 i2c_sim_init end
2023-07-30 18:14:32 power open power_version = 0x75
2023-07-30 18:14:35 power is not Calibrated
2023-07-30 18:14:35 warning:power is not calibration.
2023-07-30 18:14:36 power type version: 0x0075
2023-07-30 18:14:38 disable power watchdog: 0x0000
2023-07-30 18:14:39 Initializing the power, please wait, this may take up to 2 minutes...
2023-07-30 18:15:10 Slept 30 seconds, diff = 0.
2023-07-30 18:15:14 set_voltage_by_steps to 1500.
2023-07-30 18:15:23 start up min temp by 75a = 28
2023-07-30 18:15:26 Chain[0]: find 126 asic, times 0
2023-07-30 18:15:28 Chain[1]: find 126 asic, times 0
2023-07-30 18:15:30 Chain[2]: find 0 asic, times 0
2023-07-30 18:15:32 Chain[2]: find 0 asic, times 1
2023-07-30 18:15:33 Chain[2]: find 0 asic, times 2
2023-07-30 18:15:33 Chain 2 only find 0 asic, will power off hash board 2
2023-07-30 18:15:33 ERROR_SOC_INIT: soc init failed!
2023-07-30 18:15:33 stop_mining: soc init failed!
2023-07-30 18:15:33 uninit_temp_info
2023-07-30 18:15:33 do not read temp anymore...
2023-07-30 18:15:33 cancel thread
2023-07-30 18:15:33 ****power off hashboard****
2023-07-30 18:15:34 temp monitor thread exit
2023-07-30 18:15:50 Version num 65536
2023-07-30 18:15:50 Mask num 0x1fffe000
2023-07-30 18:15:50 opt_multi_version = 65536, interval timeout = 4481704
2023-07-30 18:15:50 freq = 345, percent = 90, hcn = 7598, timeout = 4481704
0

Comments

9 comments

Date Votes
  • Nick

    Dear customer.

     

    From the kernel log, it can't detect the hashboard. please kindly exclude the issue by following steps:

     

    1.Check the wires for the hashboard--pull them and re-plug them again, and also you can try to change the new wires.

     

    2.Please clean up the dust.

    How To Clean and Dust The Antminers

    https://support.bitmain.com/hc/en-us/articles/115004520173-How-To-Clean-and-Dust-The-Antminers

     

    If there are still the same problems after the above steps, please send it to repair.

     

    Best regards

    BITMAIN

    0
    Comment actions Permalink
  • Nick

    Dear Customer,

    If you have any questions please feel free to contact us.

    Please send email to customersupport@bitmain.com

    We will reply to your question as soon as possible.

    0
    Comment actions Permalink
  • Rajveer Singh

    Which wires to check ?? The power cables??

    0
    Comment actions Permalink
  • Nick

    Check the wires for the hashboard

    0
    Comment actions Permalink
  • Nick

    Dear Customer,

    If you have any questions please feel free to contact us.

    Please send email to customersupport@bitmain.com

    We will reply to your question as soon as possible.

    0
    Comment actions Permalink
  • Rajveer Singh

    Which wires, can you please share me a reference image

    0
    Comment actions Permalink
  • Nick

    Dear Customer,

    we can not send photo here.

    Please send email to customersupport@bitmain.com

    We will reply to your question as soon as possible.

    0
    Comment actions Permalink
  • Jay

    Good morning
    The log shows that hash board 3 is faulty
    If you need help, you can contact me, this is my number
    Zeus Mining
    https://www.zeusbtc.com/?nocheck=Vrq5Aj9U

     

     

     

    0
    Comment actions Permalink
  • Nick

    Dear Customer,

    If you have any questions please feel free to contact us.

    Please send email to customersupport@bitmain.com

    We will reply to your question as soon as possible.

    0
    Comment actions Permalink

Please sign in to leave a comment.

Didn't find what you were looking for?

New post