S19 90th warning:power is not calibration
Hello
What i've got info from log.
...
2023-07-01 04:28:00 start to init...
2023-07-01 04:28:00 i2c_sim_init start
2023-07-01 04:28:00 init gpio477
2023-07-01 04:28:00 init gpio476
2023-07-01 04:28:00 i2c_sim_init end
2023-07-01 04:28:01 power open power_version = 0x75
2023-07-01 04:28:04 power is not Calibrated
2023-07-01 04:28:04 warning:power is not calibration.
2023-07-01 04:28:05 power type version: 0x0075
2023-07-01 04:28:06 disable power watchdog: 0x0000
2023-07-01 04:28:23 Initializing the power, please wait, this may take up to 2 minutes...
2023-07-01 04:28:54 Slept 30 seconds, diff = 3.
2023-07-01 04:28:58 set_voltage_by_steps to 1500.
2023-07-01 04:29:07 start up min temp by 75a = 19
2023-07-01 04:29:10 Chain[0]: find 126 asic, times 0
2023-07-01 04:29:12 Chain[1]: find 126 asic, times 0
2023-07-01 04:29:14 Chain[2]: find 126 asic, times 0
2023-07-01 04:29:19 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2023-07-01 04:29:24 Bring up temperature is 20
2023-07-01 04:29:24 set UART baud to 3000000
2023-07-01 04:29:24 create thread check_miner_status_thread
2023-07-01 04:29:24 create thread check_system_work_thread
2023-07-01 04:29:24 set_voltage_by_steps to 1450.
2023-07-01 04:29:26 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2023-07-01 04:29:26 start do_core_reset
2023-07-01 04:29:45 end do_core_reset
2023-07-01 04:29:45 fixed step freq_start = 50, freq_end = 475, freq_step = 6.25
2023-07-01 04:29:45 chain = 0 set freq to 56.25
2023-07-01 04:29:45 chain = 1 set freq to 56.25
2023-07-01 04:29:45 chain = 2 set freq to 56.25
2023-07-01 04:29:46 chain = 0 set freq to 62.50
2023-07-01 04:29:46 chain = 1 set freq to 62.50
2023-07-01 04:29:46 chain = 2 set freq to 62.50
2023-07-01 04:29:46 chain = 0 set freq to 68.75...
What is "power is not Calibrated" what i should to do?
When i waked up miner was not work, i just rebooted it and it started working!
-
Dear customer.
please kindly exclude the issue by following steps:
1. Plugin and out the PSU cord.
2. Set miner to factory settings
How to set miner to factory settings
https://support.bitmain.com/hc/en-us/articles/115003595387-How-to-reset-miner-to-factory-settings-
3. Change the PSU
https://support.bitmain.com/hc/en-us/articles/115004339274--How-to-use-a-multimeter-to-test-PSU
https://support.bitmain.com/hc/en-us/articles/4809007246617-PSU-problems-and-solutions-apply-to-APW9-APW12-If there are still problems after the above steps, please send the latest kernel log and miner status.
We will double-check for you.
Best regards
BITMAIN
-
Dear Customer,
If you have any questions please feel free to contact us.
Please send email to customersupport@bitmain.com
We will reply to your question as soon as possible.
-
Dear Customer,
If you have any questions please feel free to contact us.
Please send email to customersupport@bitmain.com
We will reply to your question as soon as possible.
Please sign in to leave a comment.
Comments
4 comments