i have problem with new s19 j pro 100t
Chain 2 only find 85 asic, will power off hash board 2
-
Dear customer.
From the kernel log, it can't detect all chips. please kindly exclude the issue by following steps:
1.Check the wires for the hashboard--pull them and re-plug them again, and also you can try to change the new wires.
2.Please clean up the dust.
How To Clean and Dust The Antminers
https://support.bitmain.com/hc/en-us/articles/115004520173-How-To-Clean-and-Dust-The-Antminers
3.Test for PSU failure and ensure the miner is grounded well.
https://support.bitmain.com/hc/en-us/articles/115004339274--How-to-use-a-multimeter-to-test-PSU
If there are still the same problems after the above steps, please send it to repair.
Best regards
BITMAIN
-
Dear Customer,
If you have any questions please feel free to contact us.
Please send email to customersupport@bitmain.com
We will reply to your question as soon as possible.
-
there are still the same problems
[ 0.000000@0] Booting Linux on physical CPU 0x0 [ 0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Mon Dec 26 17:29:52 CST 2022 [ 0.000000@0] Boot CPU: AArch64 Processor [410fd034] [ 0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '') [ 0.000000@0] bootconsole [aml_uart0] enabled [ 0.000000@0] efi: Getting EFI parameters from FDT: [ 0.000000@0] efi: UEFI not found. [ 0.000000@0] 07400000 - 07500000, 1024 KB, ramoops@0x07400000 [ 0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB [ 0.000000@0] 05000000 - 05400000, 4096 KB, linux,secmon [ 0.000000@0] __reserved_mem_alloc_size, start:0x000000003e000000, end:0x0000000040000000, len:32 MiB [ 0.000000@0] failed to allocate memory for node linux,meson-fb, size:32 MB [ 0.000000@0] cma: Reserved 16 MiB at 0x000000000f000000 [ 0.000000@0] On node 0 totalpages: 65536 [ 0.000000@0] DMA zone: 1024 pages used for memmap [ 0.000000@0] DMA zone: 0 pages reserved [ 0.000000@0] DMA zone: 65536 pages, LIFO batch:15 [ 0.000000@0] psci: probing for conduit method from DT. [ 0.000000@0] psci: PSCIv1.0 detected in firmware. [ 0.000000@0] psci: Using standard PSCI v0.2 function IDs [ 0.000000@0] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000@0] psci: SMC Calling Convention v1.1 [ 0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00ef53000 s64536 r8192 d29672 u102400 [ 0.000000@0] pcpu-alloc: s64536 r8192 d29672 u102400 alloc=25*4096 [ 0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000@0] Detected VIPT I-cache on CPU0 [ 0.000000@0] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64512 [ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 rootfstype=ramfs init=/sbin/init [ 0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes) [ 0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.000000@0] Memory: 211688K/262144K available (8764K kernel code, 1194K rwdata, 2424K rodata, 3648K init, 1017K bss, 29976K reserved, 20480K cma-reserved) [ 0.000000@0] Virtual kernel memory layout: [ 0.000000@0] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000@0] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000@0] .text : 0xffffff8009080000 - 0xffffff8009910000 ( 8768 KB) [ 0.000000@0] .rodata : 0xffffff8009910000 - 0xffffff8009b80000 ( 2496 KB) [ 0.000000@0] .init : 0xffffff8009b80000 - 0xffffff8009f10000 ( 3648 KB) [ 0.000000@0] .data : 0xffffff8009f10000 - 0xffffff800a03aa00 ( 1195 KB) [ 0.000000@0] .bss : 0xffffff800a03aa00 - 0xffffff800a139034 ( 1018 KB) [ 0.000000@0] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB) [ 0.000000@0] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000@0] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000@0] 0xffffffbf00000000 - 0xffffffbf00400000 ( 4 MB actual) [ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc010000000 ( 256 MB) [ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000@0] Preemptible hierarchical RCU implementation. [ 0.000000@0] Build-time adjustment of leaf fanout to 64. [ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0 [ 0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized [ 0.000000@0] axg_aoclkc_init: register ao clk ok! [ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk [ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk [ 0.000000@0] axg_amlogic_init_media: register meson media clk [ 0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks [ 0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk [ 0.000000@0] axg_clkc_init initialization complete [ 0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.008251@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194 [ 0.016899@0] Console: colour dummy device 80x25 [ 0.021106@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.031586@0] pid_max: default: 32768 minimum: 301 [ 0.036436@0] thread_stack_cache_init, vmap:ffffffc00e5af600, bitmap:ffffffc00e5a3000, cache page:e5e0 [ 0.045772@0] thread_stack_cache_init, allocation vm area:ffffffc00e5d94c0, addr:ffffff8020000000, size:20001000 [ 0.056005@0] cpu 0, vmap_stack:[ffffffc00ef5c960-ffffffc00ef60950] [ 0.062304@0] cpu 0, irq_stack: [ffffffc00ef53060-ffffffc00ef57050] [ 0.068604@0] cpu 1, vmap_stack:[ffffffc00ef75960-ffffffc00ef79950] [ 0.074903@0] cpu 1, irq_stack: [ffffffc00ef6c060-ffffffc00ef70050] [ 0.081203@0] cpu 2, vmap_stack:[ffffffc00ef8e960-ffffffc00ef92950] [ 0.087504@0] cpu 2, irq_stack: [ffffffc00ef85060-ffffffc00ef89050] [ 0.093803@0] cpu 3, vmap_stack:[ffffffc00efa7960-ffffffc00efab950] [ 0.100103@0] cpu 3, irq_stack: [ffffffc00ef9e060-ffffffc00efa2050] [ 0.106463@0] Security Framework initialized [ 0.110695@0] SELinux: Initializing. [ 0.114388@0] SELinux: Starting in permissive mode [ 0.114423@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes) [ 0.121108@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes) [ 0.128837@0] ftrace: allocating 30061 entries in 118 pages [ 0.186283@0] sched-energy: CPU device node has no sched-energy-costs [ 0.187094@0] CPU0: update cpu_capacity 1024 [ 0.191421@0] ASID allocator initialised with 32768 entries [ 0.229561@0] secmon: can't fine clear_range [ 0.229765@0] EFI services will not be available. [ 0.233034@0] Meson chip version = RevC (25:C - 23:0) [ 0.266714@1] Detected VIPT I-cache on CPU1 [ 0.266773@1] CPU1: update cpu_capacity 1024 [ 0.266775@1] CPU1: Booted secondary processor [410fd034] [ 0.294775@2] Detected VIPT I-cache on CPU2 [ 0.294827@2] CPU2: update cpu_capacity 1024 [ 0.294830@2] CPU2: Booted secondary processor [410fd034] [ 0.322836@3] Detected VIPT I-cache on CPU3 [ 0.322885@3] CPU3: update cpu_capacity 1024 [ 0.322888@3] CPU3: Booted secondary processor [410fd034] [ 0.322974@0] Brought up 4 CPUs [ 0.362197@0] SMP: Total of 4 processors activated. [ 0.367106@0] CPU features: detected feature: 32-bit EL0 Support [ 0.373142@0] CPU features: detected feature: Kernel page table isolation (KPTI) [ 0.383694@0] CPU: All CPU(s) started at EL2 [ 0.384882@0] alternatives: patching kernel code [ 0.390184@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755 [ 0.397407@0] devtmpfs: initialized [ 0.412387@0] DMI not present or invalid. [ 0.412748@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.420754@0] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.427331@0] pinctrl core: initialized pinctrl subsystem [ 0.433718@0] NET: Registered protocol family 16 [ 0.457286@0] cpuidle: using governor menu [ 0.457774@0] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000) [ 0.463387@0] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers. [ 0.470798@0] DMA: preallocated 256 KiB pool for atomic allocations [ 0.476986@0] clkmsr: clkmsr: driver init [ 0.480996@0] aml_watch_point_probe, in, wp:2 [ 0.485572@0] pstore: using zlib compression [ 0.489842@0] console [pstore-1] enabled [ 0.493273@0] pstore: Registered ramoops as persistent store backend [ 0.499685@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0 [ 0.514031@0] aml_iomap: amlogic iomap probe done [ 0.520868@0] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c [ 0.522808@0] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0 [ 0.611960@0] usbcore: registered new interface driver usbfs [ 0.612125@0] usbcore: registered new interface driver hub [ 0.617742@0] usbcore: registered new device driver usb [ 0.623039@0] pps_core: LinuxPPS API ver. 1 registered [ 0.627982@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.637371@0] PTP clock support registered [ 0.641718@0] dmi: Firmware registration failed. [ 0.650517@0] secmon: reserve_mem_size:0x300000 [ 0.650684@0] secmon secmon: assigned reserved memory node linux,secmon [ 0.657639@0] secmon: get page:ffffffbf00140000, 5000 [ 0.662353@0] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000 [ 0.670729@0] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000 [ 0.678599@0] NetLabel: Initializing [ 0.680778@0] NetLabel: domain hash size = 128 [ 0.685363@0] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.690591@0] NetLabel: unlabeled traffic allowed by default [ 0.697199@0] clocksource: Switched to clocksource arch_sys_counter [ 0.824003@0] VFS: Disk quotas dquot_6.6.0 [ 0.824150@0] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.850284@0] NET: Registered protocol family 2 [ 0.851326@0] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.856521@0] TCP bind hash table entries: 2048 (order: 3, 32768 bytes) [ 0.863264@0] TCP: Hash tables configured (established 2048 bind 2048) [ 0.869784@0] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.875738@0] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.882480@0] NET: Registered protocol family 1 [ 0.887436@0] RPC: Registered named UNIX socket transport module. [ 0.892884@0] RPC: Registered udp transport module. [ 0.897769@0] RPC: Registered tcp transport module. [ 0.902659@0] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.911768@0] Unpacking initramfs... [ 1.412347@3] Initramfs unpacking failed: junk in compressed archive [ 1.419161@3] Freeing initrd memory: 6572K [ 1.420057@3] hw perfevents: clusterb_enabled = 0 [ 1.422427@3] hw perfevents: cpumasks 0xf, 0x0 [ 1.426874@3] hw perfevents: cluster A irq = 7 [ 1.431448@3] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.441574@3] audit: initializing netlink subsys (disabled) [ 1.444933@3] audit: type=2000 audit(1.256:1): initialized [ 1.452218@3] workingset: timestamp_bits=62 max_order=16 bucket_order=0 [ 1.476295@3] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.479277@3] NFS: Registering the id_resolver key type [ 1.482009@3] Key type id_resolver registered [ 1.486336@3] Key type id_legacy registered [ 1.490971@3] fuse init (API version 7.26) [ 1.496336@3] SELinux: Registering netfilter hooks [ 1.502505@3] NET: Registered protocol family 38 [ 1.502566@3] Key type asymmetric registered [ 1.505809@3] Asymmetric key parser 'x509' registered [ 1.511296@3] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.518583@3] io scheduler noop registered (default) [ 1.523483@3] io scheduler deadline registered [ 1.528277@3] io scheduler cfq registered [ 1.548584@1] random: fast init done [ 1.548682@1] random: crng init done [ 1.549140@3] Unable to detect cache hierarchy for CPU 0 [ 1.585449@3] loop: module loaded [ 1.590944@3] zram: Added device: zram0 [ 1.591335@3] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.596208@3] libphy: Fixed MDIO Bus: probed [ 1.600987@3] tun: Universal TUN/TAP device driver, 1.6 [ 1.605364@3] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.613628@3] ee eth reset:Addr = ffffff80081fd008 [ 1.621032@3] meson6-dwmac ff3f0000.ethernet: no reset control found [ 1.623040@3] stmmac - user ID: 0x11, Synopsys ID: 0x37 [ 1.628276@3] Ring mode enabled [ 1.631504@3] DMA HW capability register supported [ 1.636236@3] Normal descriptors [ 1.639551@3] RX Checksum Offload Engine supported [ 1.644455@3] COE Type 2 [ 1.647077@3] TX Checksum insertion supported [ 1.651540@3] Wake-Up On Lan supported [ 1.655482@3] Enable RX Mitigation via HW Watchdog Timer [ 1.669002@3] libphy: stmmac: probed [ 1.669055@3] eth%d: PHY ID 0007c0f1 at 0 IRQ POLL (stmmac-0:00) active [ 1.675472@3] PPP generic driver version 2.4.2 [ 1.678493@3] PPP BSD Compression module registered [ 1.682985@3] PPP Deflate Compression module registered [ 1.688235@3] PPP MPPE Compression module registered [ 1.693201@3] NET: Registered protocol family 24 [ 1.698697@3] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.704614@3] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.711644@3] usbcore: registered new interface driver cdc_acm [ 1.716856@3] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.725293@3] usbcore: registered new interface driver usbserial [ 1.731962@3] mousedev: PS/2 mouse device common for all mice [ 1.737429@3] usbcore: registered new interface driver xpad [ 1.742801@3] i2c /dev entries driver [ 1.747569@3] cpu cpu0: bL_cpufreq_init: CPU 0 initialized [ 1.751832@3] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi [ 1.762770@3] ff803000.serial: clock gate not found [ 1.764309@3] meson_uart ff803000.serial: ==uart0 reg addr = ffffff800830d000 [ 1.771541@3] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 13, base_baud = 1500000) is a meson_uart [ 1.786461@3] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200 [ 1.789147@3] console [ttyS0] enabled [ 1.796389@3] bootconsole [aml_uart0] disabled [ 1.806068@1] ff804000.serial: clock gate not found [ 1.810171@1] meson_uart ff804000.serial: ==uart3 reg addr = ffffff8008321000 [ 1.817338@1] ff804000.serial: ttyS3 at MMIO 0xff804000 (irq = 14, base_baud = 1500000) is a meson_uart [ 1.827638@3] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff8008323000 [ 1.833784@3] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 25, base_baud = 1500000) is a meson_uart [ 1.843936@0] meson_uart ffd23000.serial: ==uart2 reg addr = ffffff8008325000 [ 1.850258@0] ffd23000.serial: ttyS2 at MMIO 0xffd23000 (irq = 26, base_baud = 1500000) is a meson_uart [ 1.861170@1] amlogic-new-usb2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff8008348000 [ 1.870497@1] amlogic-new-usb3 ffe09080.usb3phy: This phy has no usb port [ 1.876990@1] amlogic-new-usb3 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff800834c080 [ 1.892003@3] i2c i2c-1: of_i2c: modalias failure on /soc/aobus@ff800000/i2c@5000/mcu6350@40 [ 1.895879@3] i2c i2c-1: Failed to create I2C device for /soc/aobus@ff800000/i2c@5000/mcu6350@40 [ 1.908132@3] aml_dma ff63e000.aml_dma: Aml dma [ 1.911320@3] aml_aes_dma ff63e000.aml_dma:aml_aes: Aml AES_dma [ 1.916308@3] aml_sha_dma ff63e000.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma [ 1.922684@3] efusekeynum: 4 [ 1.925008@3] efusekeyname: mac offset: 0 size: 6 [ 1.931462@3] efusekeyname: mac_bt offset: 6 size: 6 [ 1.937861@3] efusekeyname: mac_wifi offset: 12 size: 6 [ 1.944279@3] efusekeyname: usid offset: 18 size: 16 [ 1.951108@2] efuse efuse: probe OK! [ 1.956516@2] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller [ 1.963779@2] meson-mmc: >>>>>>>>hostbase ffffff8008358000, dmode [ 1.968875@2] meson-mmc: actual_clock :400000, HHI_nand: 0x80 [ 1.974080@2] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c [ 2.017311@2] meson-mmc: meson_mmc_probe() : success! [ 2.017564@2] amlogic mtd driver init [ 2.021631@2] prase_get_dtb_nand_parameter:128,parse dts start [ 2.026397@2] bl mode descrete [ 2.029258@2] fip_copies 4 [ 2.031923@2] fip_size 0x200000 [ 2.035061@2] nand_clk_ctrl 0xffe07000 [ 2.038785@2] prase_get_dtb_nand_parameter:234,parse dts end [ 2.044453@2] nand_clk_ctrl 0xffe07000 [ 2.048172@2] nand register base ffffff80083df800, nand clock register ffffff80083e1000 [ 2.056909@2] plat->aml_nand_device ffffff800a005c10 [ 2.061088@2] m3_nand_probe() aml_nand_device ffffff800a005c10 [ 2.067148@2] NAND device id: 2c da 90 95 6 0 [ 2.071219@2] NAND device: Manufacturer ID: [ 2.075281@2] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A) [ 2.082324@2] oob_fill_cnt =32 oob_size =64, bch_bytes =14 [ 2.087754@2] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16 [ 2.093302@2] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1 [ 2.099547@2] mtd->oobavail: 0x8 [ 2.102944@2] aml_nand_init 2119: plat-name:bootloader [ 2.107866@2] Creating 1 MTD partitions on "bootloader": [ 2.113155@2] 0x000000000000-0x000000200000 : "bootloader" [ 2.122508@0] bootloader initialized ok [ 2.122604@0] plat->aml_nand_device ffffff800a005c10 [ 2.127392@0] m3_nand_probe() aml_nand_device ffffff800a005c10 [ 2.133549@0] NAND device id: 2c da 90 95 6 0 [ 2.137531@0] NAND device: Manufacturer ID: [ 2.141586@0] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A) [ 2.148619@0] oob_fill_cnt =32 oob_size =64, bch_bytes =14 [ 2.154061@0] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16 [ 2.159601@0] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1 [ 2.165855@0] mtd->oobavail: 0x8 [ 2.169323@0] aml_nand_init 2119: plat-name:nandnormal [ 2.174227@0] bbt_start=20 [ 2.176828@0] env_start=24 [ 2.179534@0] key_start=32 [ 2.182219@0] dtb_start=40 [ 2.184887@0] ddr_start=44 [ 2.187596@0] nbbt: info size=0x800 max_scan_blk=24, start_blk=20 [ 2.194085@0] get_free_node 43: bitmap=0 [ 2.197561@0] get_free_node 55: bitmap=1 [ 2.201652@0] get_free_node 43: bitmap=1 [ 2.205359@0] get_free_node 55: bitmap=3 [ 2.209452@0] get_free_node 43: bitmap=3 [ 2.213142@0] get_free_node 55: bitmap=7 [ 2.217062@0] nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1 [ 2.223731@0] nbbt free list: [ 2.226679@0] blockN=21, ec=-1, dirty_flag=0 [ 2.230925@0] blockN=22, ec=-1, dirty_flag=0 [ 2.235171@0] blockN=23, ec=-1, dirty_flag=0 [ 2.239419@0] aml_nand_scan_rsv_info 1141: page_num=1 [ 2.244827@0] nbbt valid addr: 280000 [ 2.248087@0] aml_nand_bbt_check 1306 bbt is valid, reading. [ 2.253721@0] aml_nand_read_rsv_info:423,read nbbt info at 280000 [ 2.259980@0] nenv: info size=0x10000 max_scan_blk=32, start_blk=24 [ 2.266408@0] get_free_node 43: bitmap=7 [ 2.269927@0] get_free_node 55: bitmap=f [ 2.274017@0] get_free_node 43: bitmap=f [ 2.277726@0] get_free_node 55: bitmap=1f [ 2.281904@0] get_free_node 43: bitmap=1f [ 2.285700@0] get_free_node 55: bitmap=3f [ 2.289877@0] get_free_node 43: bitmap=3f [ 2.293673@0] get_free_node 55: bitmap=7f [ 2.297851@0] get_free_node 43: bitmap=7f [ 2.301646@0] get_free_node 55: bitmap=ff [ 2.305824@0] get_free_node 43: bitmap=ff [ 2.309620@0] get_free_node 55: bitmap=1ff [ 2.313884@0] get_free_node 43: bitmap=1ff [ 2.317766@0] get_free_node 55: bitmap=3ff [ 2.321853@0] nenv : phy_blk_addr=24, ec=0, phy_page_addr=0, timestamp=1 [ 2.328511@0] nenv free list: [ 2.331458@0] blockN=25, ec=-1, dirty_flag=0 [ 2.335703@0] blockN=26, ec=-1, dirty_flag=0 [ 2.339951@0] blockN=27, ec=-1, dirty_flag=0 [ 2.344197@0] blockN=28, ec=-1, dirty_flag=0 [ 2.348444@0] blockN=29, ec=-1, dirty_flag=0 [ 2.352691@0] blockN=30, ec=-1, dirty_flag=0 [ 2.356938@0] blockN=31, ec=-1, dirty_flag=0 [ 2.361195@0] aml_nand_scan_rsv_info 1141: page_num=32 [ 2.378387@0] nenv valid addr: 310000 [ 2.378420@0] nkey: info size=0x8000 max_scan_blk=40, start_blk=32 [ 2.382776@0] get_free_node 43: bitmap=3ff [ 2.386658@0] get_free_node 55: bitmap=7ff [ 2.390923@0] get_free_node 43: bitmap=7ff [ 2.394804@0] get_free_node 55: bitmap=fff [ 2.399068@0] get_free_node 43: bitmap=fff [ 2.402951@0] get_free_node 55: bitmap=1fff [ 2.407303@0] get_free_node 43: bitmap=1fff [ 2.411271@0] get_free_node 55: bitmap=3fff [ 2.415622@0] get_free_node 43: bitmap=3fff [ 2.419591@0] get_free_node 55: bitmap=7fff [ 2.423942@0] get_free_node 43: bitmap=7fff [ 2.427911@0] get_free_node 55: bitmap=ffff [ 2.432262@0] get_free_node 43: bitmap=ffff [ 2.436231@0] get_free_node 55: bitmap=1ffff [ 2.440669@0] get_free_node 43: bitmap=1ffff [ 2.444724@0] get_free_node 55: bitmap=3ffff [ 2.448971@0] nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0 [ 2.455642@0] nkey free list: [ 2.458589@0] blockN=32, ec=-1, dirty_flag=0 [ 2.462836@0] blockN=33, ec=-1, dirty_flag=0 [ 2.467080@0] blockN=34, ec=-1, dirty_flag=0 [ 2.471329@0] blockN=35, ec=-1, dirty_flag=0 [ 2.475575@0] blockN=36, ec=-1, dirty_flag=0 [ 2.479822@0] blockN=37, ec=-1, dirty_flag=0 [ 2.484069@0] blockN=38, ec=-1, dirty_flag=0 [ 2.488315@0] blockN=39, ec=-1, dirty_flag=0 [ 2.492563@0] aml_nand_scan_rsv_info 1141: page_num=16 [ 2.497676@0] nkey valid addr: fffffffffffe0000 [ 2.502183@0] aml_nand_key_check 1251 NO key exist [ 2.506951@0] ndtb: info size=0x20000 max_scan_blk=44, start_blk=40 [ 2.513582@0] get_free_node 43: bitmap=3ffff [ 2.517438@0] get_free_node 55: bitmap=7ffff [ 2.521876@0] get_free_node 43: bitmap=7ffff [ 2.525931@0] get_free_node 55: bitmap=fffff [ 2.530369@0] get_free_node 43: bitmap=fffff [ 2.534424@0] get_free_node 55: bitmap=1fffff [ 2.538758@0] ndtb : phy_blk_addr=40, ec=0, phy_page_addr=0, timestamp=1 [ 2.545428@0] ndtb free list: [ 2.548359@0] blockN=41, ec=-1, dirty_flag=0 [ 2.552623@0] blockN=42, ec=-1, dirty_flag=0 [ 2.556869@0] blockN=43, ec=-1, dirty_flag=0 [ 2.561116@0] aml_nand_scan_rsv_info 1141: page_num=64 [ 2.578348@0] ndtb valid addr: 500000 [ 2.578382@0] nddr: info size=0x20000 max_scan_blk=46, start_blk=44 [ 2.582887@0] get_free_node 43: bitmap=1fffff [ 2.586973@0] get_free_node 55: bitmap=3fffff [ 2.591496@0] get_free_node 43: bitmap=3fffff [ 2.595637@0] get_free_node 55: bitmap=7fffff [ 2.599971@0] nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0 [ 2.606641@0] nddr free list: [ 2.609588@0] blockN=44, ec=-1, dirty_flag=0 [ 2.613835@0] blockN=45, ec=-1, dirty_flag=0 [ 2.618082@0] aml_nand_scan_rsv_info 1141: page_num=64 [ 2.623195@0] nddr valid addr: fffffffffffe0000 [ 2.627702@0] aml_nand_ddr_check 1281 NO ddr exist [ 2.632472@0] tpl: off 8388608, size 8388608 [ 2.764021@0] Creating 6 MTD partitions on "nandnormal": [ 2.764068@0] 0x000000800000-0x000001000000 : "tpl" [ 2.775143@3] 0x000001000000-0x000001200000 : "misc" [ 2.778312@3] 0x000001200000-0x000002200000 : "recovery" [ 2.790343@0] 0x000002200000-0x000004200000 : "boot" [ 2.809436@0] 0x000004200000-0x000004700000 : "config" [ 2.814079@0] 0x000004700000-0x000010000000 : "nvdata" [ 2.914929@0] nandnormal initialized ok [ 2.915037@0] aml_ubootenv_init: register env chardev [ 2.918559@0] aml_ubootenv_init: register env chardev OK [ 2.923602@0] amlnf_dtb_init: register dtb cdev [ 2.928319@0] amlnf_dtb_init: register dtd cdev OK [ 2.932773@0] mtd_nand_probe 267 , err = 0 [ 2.937915@0] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc0 [ 2.943332@0] input: aml_vkeypad as /devices/platform/rtc/input/input0 [ 2.950332@0] unifykey: storage in base: 0xffffffc005000000 [ 2.954956@0] unifykey: storage out base: 0xffffffc005040000 [ 2.960563@0] unifykey: storage block base: 0xffffffc005080000 [ 2.966368@0] unifykey: probe done! [ 2.970554@0] unifykey: no efuse-version set, use default value: -1 [ 2.976094@0] unifykey: key unify config unifykey-num is 6 [ 2.981626@0] unifykey: key unify fact unifykey-num is 6 [ 2.986829@0] unifykey: unifykey_devno: f200000 [ 2.991811@1] unifykey: device unifykeys created ok [ 2.996402@1] unifykey: aml_unifykeys_init done! [ 3.001260@1] sysled: module init [ 3.004673@1] meson_wdt ffd0f0d0.watchdog: start watchdog [ 3.009484@1] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog [ 3.016840@3] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done [ 3.025729@1] dmc_monitor_probe [ 3.031928@1] defendkey defendkey: Reserved memory is not enough! [ 3.032421@1] defendkey: probe of defendkey failed with error -22 [ 3.038837@1] GACT probability NOT on [ 3.042161@1] Mirror/redirect action on [ 3.045944@1] u32 classifier [ 3.048771@1] Actions configured [ 3.052359@1] Netfilter messages via NETLINK v0.30. [ 3.057615@1] nf_conntrack version 0.5.0 (2048 buckets, 8192 max) [ 3.063829@1] ctnetlink v0.93: registering with nfnetlink. [ 3.069701@1] xt_time: kernel timezone is -0000 [ 3.073416@1] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 3.080022@1] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.084760@1] arp_tables: arp_tables: (C) 2002 David S. Miller [ 3.090227@1] Initializing XFRM netlink socket [ 3.095738@1] NET: Registered protocol family 10 [ 3.101689@1] mip6: Mobile IPv6 [ 3.102297@1] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 3.108276@1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.116263@1] NET: Registered protocol family 17 [ 3.118546@1] NET: Registered protocol family 15 [ 3.123147@1] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 3.136290@1] l2tp_core: L2TP core driver, V2.0 [ 3.140683@1] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 3.145600@1] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 3.151354@1] l2tp_netlink: L2TP netlink interface [ 3.156164@1] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 3.162226@1] l2tp_debugfs: L2TP debugfs support [ 3.166764@1] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 3.173410@1] NET: Registered protocol family 35 [ 3.178325@1] Key type dns_resolver registered [ 3.182888@1] Registered swp emulation handler [ 3.186792@1] Registered cp15_barrier emulation handler [ 3.191978@1] Registered setend emulation handler [ 3.196723@1] disable EAS feature [ 3.201372@0] registered taskstats version 1 [ 3.217890@3] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host [ 3.724373@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.724458@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 3.732771@3] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f664 hci version 0x100 quirks 0x02010010 [ 3.741209@3] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0xff500000 [ 3.748642@2] hub 1-0:1.0: USB hub found [ 3.751133@2] hub 1-0:1.0: 1 port detected [ 3.755728@2] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.760759@2] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 3.768651@2] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.778137@1] hub 2-0:1.0: USB hub found [ 3.780713@1] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 3.788055@1] usb usb2: Unsupported the hub [ 3.792797@1] aml_vrtc rtc: setting system clock to 2015-01-01 00:00:08 UTC (1420070408) [ 3.800859@1] dwc_otg ff400000.dwc2_a: dwc_otg_driver_probe(ffffffc00d19f000) [ 3.800936@1] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0 [ 3.808836@1] dwc_otg ff400000.dwc2_a: base=0xffffff8008580000 [ 3.808848@1] dwc_otg ff400000.dwc2_a: dwc_otg_device=0xffffffc00bbfcc00 [ 3.909327@0] dwc_otg: Core Release: 3.10a [ 3.909387@0] dwc_otg: Setting default values for core params [ 3.913570@0] dwc_otg: curmode: 0, host_only: 0 [ 3.918081@0] dwc_otg ff400000.dwc2_a: DMA config: BURST_DEFAULT [ 3.930595@0] dwc_otg: Using Buffer DMA mode [ 3.930633@0] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1 [ 3.934541@0] dwc_otg: Working on port type = SLAVE [ 3.939398@0] dwc_otg: Dedicated Tx FIFOs mode [ 3.946353@0] thermal thermal_zone0: binding zone soc_thermal with cdev thermal-cpufreq-0 failed:-22 [ 3.953113@0] cpucore_cooling_register, max_cpu_core_num:4 [ 3.965303@0] gxbb_pm: enter meson_pm_probe! [ 3.965359@0] no vddio3v3_en pin [ 3.967006@0] pm-meson aml_pm: Can't get switch_clk81 [ 3.972103@0] gxbb_pm: meson_pm_probe done [ 3.977025@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200 [ 3.983392@0] Freeing unused kernel memory: 3648K [ 3.997832@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200 [ 4.252575@3] ubi0: attaching mtd5 [ 4.271042@3] ubi0: scanning is finished [ 4.275842@1] ubi0: attached mtd5 (name "config", size 5 MiB) [ 4.275974@1] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.283039@1] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.289943@1] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.297053@1] ubi0: good PEBs: 40, bad PEBs: 0, corrupted PEBs: 0 [ 4.303111@1] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 4.310486@1] ubi0: max/mean erase counter: 10/5, WL threshold: 4096, image sequence number: 208212391 [ 4.319751@1] ubi0: available PEBs: 0, total reserved PEBs: 40, PEBs reserved for bad PEB handling: 4 [ 4.328969@3] ubi0: background thread "ubi_bgt0d" started, PID 1076 [ 4.342008@1] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 1080 [ 4.358657@0] UBIFS (ubi0:0): recovery needed [ 4.411331@3] UBIFS (ubi0:0): recovery completed [ 4.411591@3] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "config_data" [ 4.418342@3] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 4.428374@3] UBIFS (ubi0:0): FS size: 2793472 bytes (2 MiB, 22 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) [ 4.438597@3] UBIFS (ubi0:0): reserved for root: 131942 bytes (128 KiB) [ 4.445233@3] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID E6D4FE57-33FA-4BC0-A2F0-AA414213B528, small LPT model [ 4.469505@0] ubi2: attaching mtd6 [ 5.141640@0] ubi2: scanning is finished [ 5.148626@0] ubi2: attached mtd6 (name "nvdata", size 185 MiB) [ 5.148932@0] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 5.155989@0] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 5.162908@0] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 5.170002@0] ubi2: good PEBs: 1480, bad PEBs: 0, corrupted PEBs: 0 [ 5.176250@0] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 5.183610@0] ubi2: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 3418011160 [ 5.192890@0] ubi2: available PEBs: 0, total reserved PEBs: 1480, PEBs reserved for bad PEB handling: 4 [ 5.202268@1] ubi2: background thread "ubi_bgt2d" started, PID 1087 [ 5.215403@2] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 1091 [ 5.232011@3] UBIFS (ubi2:0): recovery needed [ 5.287296@0] UBIFS (ubi2:0): recovery completed [ 5.287588@0] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "nvdata_data" [ 5.294311@0] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 5.304341@0] UBIFS (ubi2:0): FS size: 185384960 bytes (176 MiB, 1460 LEBs), journal size 9269248 bytes (8 MiB, 73 LEBs) [ 5.315170@0] UBIFS (ubi2:0): reserved for root: 4952683 bytes (4836 KiB) [ 5.321932@0] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID 4B01C4FF-913E-4983-B07F-5A71BD77D1E6, small LPT model [ 5.543194@1] eth0: device MAC address 02:29:43:f8:9a:6f [ 5.626158@0] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP. [ 5.627442@0] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 5.874004@2] uart_trans: loading out-of-tree module taints kernel. [ 5.876608@2] register uart_trans chrdev success. [ 5.879821@2] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 0 to 9600 [ 5.887417@2] tty port open success [/dev/ttyS3]! [ 5.892215@2] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 9600 to 115200 [ 5.900480@2] init sucess for tty struct (246:3) [/dev/ttyS3] [ 5.906608@2] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 0 to 9600 [ 5.914241@2] tty port open success [/dev/ttyS2]! [ 5.918945@2] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 9600 to 115200 [ 5.927328@2] init sucess for tty struct (246:2) [/dev/ttyS2] [ 5.933494@2] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 0 to 9600 [ 5.941150@2] tty port open success [/dev/ttyS1]! [ 5.945768@2] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 115200 [ 5.954204@2] init sucess for tty struct (246:1) [/dev/ttyS1] [ 5.960448@0] create workqueue success! [ 7.669467@0] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 7.672755@0] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 8.216927@0] nf_conntrack: default automatic helper assignment has been turned off for security reasons and CT-based firewall rule not found. Use the iptables CT target to attach helpers instead. [ 32.249324@2] uart trans dev open. [ 32.249432@2] uart_buf virt addr = 0xffffffc00b180000 [ 32.252138@2] uart_buf phys addr = 0x0b180000 [ 32.256504@2] uart_buf pfn = 0x0000b180 [ 32.261286@2] uart trans stop send work timer. [ 32.265431@2] uart trans set chain exist bits:0x7. [ 32.270048@2] uart trans set work queue count 768. [ 122.142789@1] uart set baud to: 4098 [ 122.142851@1] uart set baud to: 4098 [ 122.144325@1] uart set baud to: 4098 [ 135.251790@1] uart trans start send work timer. [ 136.160590@3] uart trans stop send work timer. [ 165.724380@2] uart trans start send work timer. ===========================================Miner log=========================================== 2015-01-01 00:00:15 Open miner sn file /config/sn error 2015-01-01 00:00:15 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX sn : 2015-01-01 00:00:16 This is fix-freq version 2015-01-01 00:00:16 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer BHB42XXX 2015-01-01 00:00:16 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 17:22:17 2015-01-01 00:00:16 opt_multi_version = 1 2015-01-01 00:00:16 opt_bitmain_ab = 1 2015-01-01 00:00:16 mid_auto_gen = 1 2015-01-01 00:00:16 opt_bitmain_work_mode = 0 2015-01-01 00:00:16 port 439 already exported 2015-01-01 00:00:16 port 454 already exported 2015-01-01 00:00:16 port 440 already exported 2015-01-01 00:00:16 port 455 already exported 2015-01-01 00:00:16 port 441 already exported 2015-01-01 00:00:16 port 456 already exported 2015-01-01 00:00:16 port 438 already exported 2015-01-01 00:00:16 port 453 already exported 2015-01-01 00:00:16 port 446 already exported 2015-01-01 00:00:16 port 445 already exported 2015-01-01 00:00:16 Note: front fan is power on! 2015-01-01 00:00:16 Note: rear fan is power on! 2015-01-01 00:00:16 start the http log. 2015-01-01 00:00:16 httpListenThread start ret=0 2015-01-01 00:00:16 start listen on 6060 ... 2015-01-01 00:00:16 bad chain id = 3 2015-01-01 00:00:19 bad chain id = 3 2015-01-01 00:00:21 ==========================capability start========================== 2015-01-01 00:00:21 board num = 3 2015-01-01 00:00:21 board id = 0, chain num = 1 2015-01-01 00:00:21 chain id = 0 2015-01-01 00:00:21 board id = 1, chain num = 1 2015-01-01 00:00:21 chain id = 1 2015-01-01 00:00:21 board id = 2, chain num = 1 2015-01-01 00:00:21 chain id = 2 2015-01-01 00:00:21 ==========================capability end============================ 2015-01-01 00:00:21 chain num = 3 2015-01-01 00:00:21 skip loading levels for now 2023-05-27 15:59:00 load chain 0 eeprom data 2023-05-27 15:59:03 load chain 1 eeprom data 2023-05-27 15:59:06 load chain 2 eeprom data 2023-05-27 15:59:06 i2c_sim_init start 2023-05-27 15:59:06 init gpio477 2023-05-27 15:59:06 init gpio476 2023-05-27 15:59:06 i2c_sim_init end 2023-05-27 15:59:08 power open power_version = 0x75 2023-05-27 15:59:10 power is not Calibrated 2023-05-27 15:59:12 miner type: Antminer S19j Pro 2023-05-27 15:59:12 multi machine mode 2023-05-27 15:59:12 load machine BHB42603 conf 2023-05-27 15:59:12 machine : BHB42603 2023-05-27 15:59:12 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3 2023-05-27 15:59:12 abandon mix board! 2023-05-27 15:59:12 abandon mix board! 2023-05-27 15:59:12 fan_eft : 0 fan_pwm : 100 2023-05-27 15:59:12 create thread get_nonce_and_register_thread 2023-05-27 15:59:12 fixed working voltage = 1380 2023-05-27 15:59:12 fixed frequency is 525 2023-05-27 15:59:12 Chain [0] PCB Version: 0x0170 2023-05-27 15:59:12 Chain [0] BOM Version: 0x0010 2023-05-27 15:59:12 Chain [1] PCB Version: 0x0170 2023-05-27 15:59:12 Chain [1] BOM Version: 0x0010 2023-05-27 15:59:12 Chain [2] PCB Version: 0x0170 2023-05-27 15:59:12 Chain [2] BOM Version: 0x0010 2023-05-27 15:59:12 bad chain id = 3 2023-05-27 15:59:12 Fan check passed. 2023-05-27 15:59:12 uart_trans addr:0xf6fa3000. 2023-05-27 15:59:12 max sensor num = 4 2023-05-27 15:59:12 STATUS_INITED: soc init done! 2023-05-27 15:59:12 temperature_monitor_thread start... 2023-05-27 15:59:15 start to init... 2023-05-27 15:59:15 warning:power is not calibration. 2023-05-27 15:59:16 power type version: 0x0075 2023-05-27 15:59:17 disable power watchdog: 0x0000 2023-05-27 15:59:18 Initializing the power, please wait, this may take up to 2 minutes... 2023-05-27 16:00:28 Slept 69 seconds, diff = 3. 2023-05-27 16:00:32 set_voltage_by_steps to 1500. 2023-05-27 16:00:42 start up min temp by 75a = 25 2023-05-27 16:00:45 Chain[0]: find 126 asic, times 0 2023-05-27 16:00:47 Chain[1]: find 126 asic, times 0 2023-05-27 16:00:49 Chain[2]: find 85 asic, times 0 2023-05-27 16:00:51 Chain[2]: find 85 asic, times 1 2023-05-27 16:00:53 Chain[2]: find 84 asic, times 2 2023-05-27 16:00:53 Chain 2 only find 84 asic, will power off hash board 2 2023-05-27 16:00:53 ERROR_SOC_INIT: soc init failed! 2023-05-27 16:00:53 stop_mining: soc init failed! 2023-05-27 16:00:53 uninit_temp_info 2023-05-27 16:00:53 do not read temp anymore... 2023-05-27 16:00:53 cancel thread 2023-05-27 16:00:53 ****power off hashboard**** 2023-05-27 16:00:53 temp monitor thread exit 2023-05-27 16:00:55 Version num 65536 2023-05-27 16:00:55 Mask num 0x1fffe000 2023-05-27 16:00:55 opt_multi_version = 65536, interval timeout = 2945120 2023-05-27 16:00:55 freq = 525, percent = 90, hcn = 4993, timeout = 2945120
-
Dear Customer,
Please send email to customersupport@bitmain.com
We will reply to your question as soon as possible.
-
Dear Customer,
If you have any questions please feel free to contact us.
Please send email to customersupport@bitmain.com
We will reply to your question as soon as possible.
Please sign in to leave a comment.
Comments
7 comments