antminer S19xp dont hash

[    0.000000] [0] Booting Linux on physical CPU 0x0
[    0.000000] [0] Linux version 4.9.38-tag- (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05) ) #1 SMP PREEMPT Wed Sep 14 11:16:17 CST 2022
[    0.000000] [0] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] [0] earlycon: uart0 at MMIO32 0x0000000004140000 (options '')
[    0.000000] [0] bootconsole [uart0] enabled
[    0.000000] [0] efi: Getting EFI parameters from FDT:
[    0.000000] [0] efi: UEFI not found.
[    0.000000] [0] OF: reserved mem: allocated memory for 'ion' node: base 0x000000010df0f000, size 16 MiB
[    0.000000] [0] Ion: Ion memory setup at 0x000000010df0f000 size 16 MiB
[    0.000000] [0] OF: reserved mem: initialized node ion, compatible id ion-region
[    0.000000] [0] OF: reserved mem: allocated memory for 'vip' node: base 0x000000010fa00000, size 4 MiB
[    0.000000] [0] OF: reserved mem: allocated memory for 'vcodec' node: base 0x000000010f800000, size 2 MiB
[    0.000000] [0] OF: reserved mem: allocated memory for 'jpu' node: base 0x000000010f700000, size 1 MiB
[    0.000000] [0] OF: reserved mem: allocated memory for 'linux,cma' node: base 0x000000010f000000, size 6 MiB
[    0.000000] [0] Reserved memory: created CMA memory pool at 0x000000010f000000, size 6 MiB
[    0.000000] [0] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] [0] On node 0 totalpages: 63744
[    0.000000] [0]   DMA zone: 1024 pages used for memmap
[    0.000000] [0]   DMA zone: 0 pages reserved
[    0.000000] [0]   DMA zone: 63744 pages, LIFO batch:15
[    0.000000] [0] psci: probing for conduit method from DT.
[    0.000000] [0] psci: PSCIv1.0 detected in firmware.
[    0.000000] [0] psci: Using standard PSCI v0.2 function IDs
[    0.000000] [0] psci: Trusted OS migration not required
[    0.000000] [0] percpu: Embedded 22 pages/cpu @ffffffc00f6ad000 s52008 r8192 d29912 u90112
[    0.000000] [0] pcpu-alloc: s52008 r8192 d29912 u90112 alloc=22*4096
[    0.000000] [0] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] [0] Detected VIPT I-cache on CPU0
[    0.000000] [0] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] [0] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 62720
[    0.000000] [0] Kernel command line: console=ttyS0,115200 earlycon loglevel=8 initrd=0x103080000,32M rdinit=/init STORAGE=EMMC
[    0.000000] [0] PID hash table entries: 1024 (order: 1, 8192 bytes)
[    0.000000] [0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.000000] [0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.000000] [0] Memory: 168956K/254976K available (6908K kernel code, 868K rwdata, 1956K rodata, 768K init, 485K bss, 79876K reserved, 6144K cma-reserved)
[    0.000000] [0] Virtual kernel memory layout:
[    0.000000] [0]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000] [0]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)
[    0.000000] [0]       .text : 0xffffff8008080000 - 0xffffff8008740000   (  6912 KB)
[    0.000000] [0]     .rodata : 0xffffff8008740000 - 0xffffff8008930000   (  1984 KB)
[    0.000000] [0]       .init : 0xffffff8008930000 - 0xffffff80089f0000   (   768 KB)
[    0.000000] [0]       .data : 0xffffff80089f0000 - 0xffffff8008ac9200   (   869 KB)
[    0.000000] [0]        .bss : 0xffffff8008ac9200 - 0xffffff8008b426d8   (   486 KB)
[    0.000000] [0]     fixed   : 0xffffffbefe7fd000 - 0xffffffbefec00000   (  4108 KB)
[    0.000000] [0]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)
[    0.000000] [0]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)
[    0.000000] [0]               0xffffffbf00000000 - 0xffffffbf00400000   (     4 MB actual)
[    0.000000] [0]     memory  : 0xffffffc000000000 - 0xffffffc010000000   (   256 MB)
[    0.000000] [0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] [0] Preemptible hierarchical RCU implementation.
[    0.000000] [0] 	Build-time adjustment of leaf fanout to 64.
[    0.000000] [0] 	RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=2.
[    0.000000] [0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=2
[    0.000000] [0] NR_IRQS:64 nr_irqs:64 0
[    0.000000] [0] GIC: Using split EOI/Deactivate mode
[    0.000000] [0] arm_arch_timer: Architected cp15 timer(s) running at 25.00MHz (phys).
[    0.000000] [0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
[    0.000004] [0] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
[    0.008845] [0] Console: colour dummy device 80x25
[    0.013818] [0] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000)
[    0.024880] [0] pid_max: default: 32768 minimum: 301
[    0.030118] [0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
[    0.037226] [0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
[    0.045388] [0] ftrace: allocating 23539 entries in 92 pages
[    0.095223] [0] ASID allocator initialised with 65536 entries
[    0.134409] [0] EFI services will not be available.
[    0.167696] [1] Detected VIPT I-cache on CPU1
[    0.167750] [1] CPU1: Booted secondary processor [410fd034]
[    0.167840] [0] Brought up 2 CPUs
[    0.181535] [0] SMP: Total of 2 processors activated.
[    0.186762] [0] CPU features: detected feature: 32-bit EL0 Support
[    0.193158] [0] CPU: All CPU(s) started at EL2
[    0.197771] [0] alternatives: patching kernel code
[    0.203327] [0] devtmpfs: initialized
[    0.213821] [0] DMI not present or invalid.
[    0.218474] [0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.228912] [0] futex hash table entries: 512 (order: 4, 65536 bytes)
[    0.235913] [0] pinctrl core: initialized pinctrl subsystem
[    0.242230] [0] NET: Registered protocol family 16
[    0.248269] [0] vdso: 2 pages (1 code @ ffffff8008747000, 1 data @ ffffff80089f4000)
[    0.256297] [0] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.265022] [0] DMA: preallocated 4096 KiB pool for atomic allocations
[    0.272393] [0] clk reset: nr_reset=64 resource_size=8
[    0.290529] [0] persistent_ram: uncorrectable error in header
[    0.296571] [0] persistent_ram: uncorrectable error in header
[    0.302615] [0] persistent_ram: uncorrectable error in header
[    0.308575] [0] pstore: using zlib compression
[    0.321097] [0] console [pstore-1] enabled
[    0.325632] [0] pstore: Registered ramoops as persistent store backend
[    0.332498] [0] ramoops: attached 0xf000@0xe000000, ecc: 16/0
[    0.356807] [0] dw_dmac 4330000.dma: CVITEK DMA Controller, 8 channels, probe done!
[    0.365428] [0] SCSI subsystem initialized
[    0.370016] [0] usbcore: registered new interface driver usbfs
[    0.376224] [0] usbcore: registered new interface driver hub
[    0.382221] [0] usbcore: registered new device driver usb
[    0.389980] [0] pps_core: LinuxPPS API ver. 1 registered
[    0.395603] [0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.405530] [0] PTP clock support registered
[    0.410142] [0] dmi: Firmware registration failed.
[    0.415551] [0] Ion: ion_parse_dt_heap_common: id 0 type 2 name carveout align 1000
[    0.423799] [0] Ion: rmem_ion_device_init: heap carveout base 0x000000010df0f000 size 0x0000000001000000 dev ffffffc00c964810
[    0.435596] [0] platform carveout: assigned reserved memory node ion
[    0.445969] [0] platform carveout: [ion] add heap id 0, type 2, base 0x10df0f000, size 0x1000000
[    0.455423] [0] tee_cv_init_clk
[    0.458823] [0] Advanced Linux Sound Architecture Driver Initialized.
[    0.466557] [0] clocksource: Switched to clocksource arch_sys_counter
[    0.551940] [0] NET: Registered protocol family 2
[    0.557516] [0] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.565268] [0] TCP bind hash table entries: 2048 (order: 4, 65536 bytes)
[    0.572456] [0] TCP: Hash tables configured (established 2048 bind 2048)
[    0.579544] [0] UDP hash table entries: 256 (order: 2, 24576 bytes)
[    0.586112] [0] UDP-Lite hash table entries: 256 (order: 2, 24576 bytes)
[    0.593356] [0] NET: Registered protocol family 1
[    0.598764] [0] RPC: Registered named UNIX socket transport module.
[    0.605371] [0] RPC: Registered udp transport module.
[    0.610656] [0] RPC: Registered tcp transport module.
[    0.615989] [0] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.623333] [0] Unpacking initramfs...
[    1.005149] [0] Initramfs unpacking failed: junk in compressed archive
[    1.031955] [0] Freeing initrd memory: 32768K (ffffffc003080000 - ffffffc005080000)
[    1.040404] [0] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    1.051736] [0] workingset: timestamp_bits=62 max_order=16 bucket_order=0
[    1.071900] [0] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.079773] [0] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.088718] [1] cryptomgr_test (33) used greatest stack depth: 14800 bytes left
[    1.099124] [0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    1.107303] [0] io scheduler noop registered
[    1.111786] [0] io scheduler deadline registered
[    1.116678] [0] io scheduler cfq registered (default)
[    1.123495] [0] cvitek,pinctrl-cv1835 3001000.pinctrl: initialized cvitek pin control driver
[    1.216836] [0] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
[    1.226792] [0] console [ttyS0] disabled
[    1.231040] [0] 4140000.serial: ttyS0 at MMIO 0x4140000 (irq = 19, base_baud = 1562500) is a 16550A
[    1.240495] [0] console [ttyS0] enabled
[    1.248534] [0] bootconsole [uart0] disabled
[    1.258907] [0] 4150000.serial: ttyS1 at MMIO 0x4150000 (irq = 20, base_baud = 12500000) is a 16550A
[    1.269886] [0] 4160000.serial: ttyS2 at MMIO 0x4160000 (irq = 21, base_baud = 12500000) is a 16550A
[    1.280864] [0] 4170000.serial: ttyS3 at MMIO 0x4170000 (irq = 22, base_baud = 12500000) is a 16550A
[    1.291864] [0] 41c0000.serial: ttyS4 at MMIO 0x41c0000 (irq = 23, base_baud = 12500000) is a 16550A
[    1.310257] [0] loop: module loaded
[    1.315300] [0] libphy: Fixed MDIO Bus: probed
[    1.322619] [0] Hash table entries set to unexpected value 0
[    1.328630] [0] bm-dwmac 4510000.ethernet: no reset control found
[    1.335198] [0] stmmac - user ID: 0x0, Synopsys ID: 0x50
[    1.340818] [0] bm-dwmac 4510000.ethernet: DMA HW capability register supported
[    1.348440] [0] bm-dwmac 4510000.ethernet: RX Checksum Offload Engine supported
[    1.356115] [0] bm-dwmac 4510000.ethernet: TX Checksum insertion supported
[    1.363288] [0] bm-dwmac 4510000.ethernet: TSO supported
[    1.368897] [0] bm-dwmac 4510000.ethernet: TSO feature enabled
[    1.374994] [0] bm-dwmac 4510000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    1.387592] [0] modprobe (65) used greatest stack depth: 13376 bytes left
[    1.603306] [1] libphy: stmmac: probed
[    1.607289] [1] CVITEK CVI18XX stmmac-0:00: attached PHY driver [CVITEK CVI18XX] (mii_bus:phy_addr=stmmac-0:00, irq=-1)
[    1.618581] [1] CVITEK CVI18XX stmmac-0:01: attached PHY driver [CVITEK CVI18XX] (mii_bus:phy_addr=stmmac-0:01, irq=-1)
[    1.631649] [1] mousedev: PS/2 mouse device common for all mice
[    1.638118] [1] i2c /dev entries driver
[    1.643754] [1] sdhci: Secure Digital Host Controller Interface driver
[    1.650603] [1] sdhci: Copyright(c) Pierre Ossman
[    1.655591] [1] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.662058] [1] cvi:sdhci_cvi_probe
[    1.667970] [1] mmc0: Host Controller version 3
[    1.718586] [1] mmc0: SDHCI controller on 4300000.cv-emmc [4300000.cv-emmc] using ADMA 64-bit
[    1.730680] [1] cvi:sdhci_cvi_probe
[    1.737688] [1] mmc1: Host Controller version 3
[    1.786584] [1] mmc1: SDHCI controller on 4310000.cv-sd [4310000.cv-sd] using ADMA 64-bit
[    1.828093] [0] usbcore: registered new interface driver usbhid
[    1.834359] [0] usbhid: USB HID core driver
[    1.839051] [0] optee: probing for conduit method from DT.
[    1.845424] [0] optee: initialized driver
[    1.849787] [0] Netfilter messages via NETLINK v0.30.
[    1.855499] [0] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[    1.862334] [0] nf_tables: (c) 2007-2009 Patrick McHardy <kaber@trash.net>
[    1.869593] [0] nf_tables_compat: (c) 2012 Pablo Neira Ayuso <pablo@netfilter.org>
[    1.877824] [0] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.885161] [0] NET: Registered protocol family 10
[    1.891545] [0] random: fast init done
[    1.896178] [0] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    1.902465] [0] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    1.910275] [0] NET: Registered protocol family 17
[    1.915397] [0] 8021q: 802.1Q VLAN Support v1.8
[    1.921564] [0] registered taskstats version 1
[    1.950217] [0] Key type encrypted registered
[    1.987720] [0] hctosys: unable to open rtc device (rtc0)
[    1.994084] [0] ALSA device list:
[    1.997609] [0]   No soundcards found.
[    2.002341] [0] Freeing unused kernel memory: 768K (ffffffc000930000 - ffffffc0009f0000)
[    2.164914] [1] mmc0: new HS200 MMC card at address 0001
[    2.174847] [1] mmcblk0: mmc0:0001 SPeMMC 3.64 GiB 
[    2.184468] [1] mmcblk0boot0: mmc0:0001 SPeMMC partition 1 4.00 MiB
[    2.192175] [1] mmcblk0boot1: mmc0:0001 SPeMMC partition 2 4.00 MiB
[    2.200562] [1] mmcblk0rpmb: mmc0:0001 SPeMMC partition 3 4.00 MiB
[    2.210279] [1] Alternate GPT is invalid, using primary GPT.
[    2.216308] [1]  mmcblk0: p1 p2 p3 p4 p5 p6 p7
[    5.641676] [0] e2fsck (181) used greatest stack depth: 13040 bytes left
[    5.673195] [1] e2fsck (183) used greatest stack depth: 12928 bytes left
[    6.107777] [0] EXT4-fs (mmcblk0p5): mounted filesystem without journal. Opts: (null)
[    6.116855] [0] mount (188) used greatest stack depth: 12672 bytes left
[    6.129151] [1] EXT4-fs (mmcblk0p6): mounted filesystem without journal. Opts: (null)
[    6.148267] [0] EXT4-fs (mmcblk0p7): mounted filesystem without journal. Opts: (null)
[    6.221706] [0] cv183x_pwm: bad vermagic: kernel tainted.
[    6.227454] [0] Disabling lock debugging due to kernel taint
[    6.233384] [0] cv183x_pwm: loading out-of-tree module taints kernel.
[    6.252909] [1] CVITEK CHIP ID = 2
[    6.489135] [1] do_smccc_smc: a=0x3000006 0x0 0x1000
[    6.494530] [1] do_smccc_smc: r=0x100 0x0
[    6.503646] [0] bm-dwmac 4510000.ethernet eth0: device MAC address 86:4b:e6:ea:d2:24
[    6.583040] [0] CVITEK CVI18XX stmmac-0:00: attached PHY driver [CVITEK CVI18XX] (mii_bus:phy_addr=stmmac-0:00, irq=-1)
[    6.610392] [0] dwmac4: Master AXI performs any burst length
[    6.616415] [0] bm-dwmac 4510000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[    6.625479] [0] bm-dwmac 4510000.ethernet eth0: registered PTP clock
[    6.632523] [0] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    6.640336] [0] Enable CVITEK ethernet phy ultra auto power saving mode
[    6.771046] [0] CVITEK CVI18XX stmmac-0:00: attached PHY driver [CVITEK CVI18XX] (mii_bus:phy_addr=stmmac-0:00, irq=-1)
[    6.794238] [0] dwmac4: Master AXI performs any burst length
[    6.800208] [0] bm-dwmac 4510000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[    6.809293] [0] bm-dwmac 4510000.ethernet eth0: registered PTP clock
[    6.816263] [0] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    6.824167] [0] Enable CVITEK ethernet phy ultra auto power saving mode
[    8.871179] [0] bm-dwmac 4510000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[    8.880279] [0] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   12.013544] [1] register uart_trans chrdev success.
[   12.020052] [1] ttyS1, serial8250_request_dma
[   12.024691] [1] ttyS1, get NULL TX chan
[   12.029579] [1] ttyS1, serial8250_do_set_termios, ispeed=9600, o_speed=9600
[   12.036903] [1] Set baud rate to 115200, quot=108
[   12.041819] [1] ttyS1 default_serial_dl_write, baudrate=115200, value=108
[   12.049018] [1] tty port open success [/dev/ttyS1]!
[   12.054190] [1] ttyS1, serial8250_do_set_termios, ispeed=115200, o_speed=115200
[   12.061866] [1] Set baud rate to 115200, quot=108
[   12.066832] [1] ttyS1 default_serial_dl_write, baudrate=115200, value=108
[   12.073924] [1] init sucess for tty struct (4:65)  [/dev/ttyS1]
[   12.080950] [1] ttyS2, serial8250_request_dma
[   12.085576] [1] ttyS2, get NULL TX chan
[   12.090301] [1] ttyS2, serial8250_do_set_termios, ispeed=9600, o_speed=9600
[   12.097622] [1] Set baud rate to 115200, quot=108
[   12.102539] [1] ttyS2 default_serial_dl_write, baudrate=115200, value=108
[   12.109688] [1] tty port open success [/dev/ttyS2]!
[   12.114854] [1] ttyS2, serial8250_do_set_termios, ispeed=115200, o_speed=115200
[   12.122531] [1] Set baud rate to 115200, quot=108
[   12.127447] [1] ttyS2 default_serial_dl_write, baudrate=115200, value=108
[   12.134540] [1] init sucess for tty struct (4:66)  [/dev/ttyS2]
[   12.141588] [1] ttyS3, serial8250_request_dma
[   12.146209] [1] ttyS3, get NULL TX chan
[   12.150983] [1] ttyS3, serial8250_do_set_termios, ispeed=9600, o_speed=9600
[   12.158305] [1] Set baud rate to 115200, quot=108
[   12.163221] [1] ttyS3 default_serial_dl_write, baudrate=115200, value=108
[   12.170375] [1] tty port open success [/dev/ttyS3]!
[   12.175571] [1] ttyS3, serial8250_do_set_termios, ispeed=115200, o_speed=115200
[   12.183265] [1] Set baud rate to 115200, quot=108
[   12.188183] [1] ttyS3 default_serial_dl_write, baudrate=115200, value=108
[   12.195334] [1] init sucess for tty struct (4:67)  [/dev/ttyS3]
[   12.202380] [1] ttyS4, serial8250_request_dma
[   12.207010] [1] ttyS4, get NULL TX chan
[   12.211792] [1] ttyS4, serial8250_do_set_termios, ispeed=9600, o_speed=9600
[   12.219121] [1] Set baud rate to 115200, quot=108
[   12.224037] [1] ttyS4 default_serial_dl_write, baudrate=115200, value=108
[   12.231197] [1] tty port open success [/dev/ttyS4]!
[   12.236377] [1] ttyS4, serial8250_do_set_termios, ispeed=115200, o_speed=115200
[   12.244061] [1] Set baud rate to 115200, quot=108
[   12.248976] [1] ttyS4 default_serial_dl_write, baudrate=115200, value=108
[   12.256127] [1] init sucess for tty struct (4:68)  [/dev/ttyS4]
[   12.262531] [1] create workqueue success!
[   12.267012] [1] insmod (538) used greatest stack depth: 12288 bytes left
[   13.467681] [0] random: crng init done
[   30.897681] [0] uart trans dev open.
[   30.901545] [0] uart_buf virt addr = 0xffffffc0033c0000
[   30.907080] [0] uart_buf phys addr = 0x1033c0000
[   30.911927] [0] uart_buf pfn       = 0x001033c0
[   30.916703] [0] uart trans stop send work timer.
[   30.921746] [0] uart trans set chain exist bits:0x7.
[   30.926991] [0] uart trans set work queue count 768.
[   60.239166] [0] cgminer-api (1759) used greatest stack depth: 12064 bytes left
[   60.504204] [0] cgminer-api (1836) used greatest stack depth: 11648 bytes left
[  112.880212] [0] uart set baud to: 4098
[  112.884269] [0] uart set baud to: 4098
[  112.888458] [0] uart set baud to: 4098
[  119.283275] [0] uart trans stop send work timer.
[  141.514822] [1] uart trans start send work timer.
[  257.862360] [0] ntpd (339) used greatest stack depth: 11440 bytes left
[ 1035.954580] [0] bm-dwmac 4510000.ethernet eth0: Link is Down
[ 1040.050821] [0] bm-dwmac 4510000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
[ 1064.626930] [0] bm-dwmac 4510000.ethernet eth0: Link is Down
[ 1066.675000] [0] bm-dwmac 4510000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[ 1070.770952] [0] bm-dwmac 4510000.ethernet eth0: Link is Down
[ 1072.819172] [0] bm-dwmac 4510000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx


===========================================Miner log===========================================
1970-01-01 00:00:12 Miner compile time: Wed Sep 14 11:03:49 CST 2022 type: Antminer BHB56XXX sn :BCMEEAUBCJBJC007J
1970-01-01 00:00:13 This is fix-freq version
1970-01-01 00:00:13 Miner compile time: Wed Sep 14 11:03:49 CST 2022 type: Antminer BHB56XXX
1970-01-01 00:00:13 Miner sn: BCMEEAUBCJBJC007J
1970-01-01 00:00:13 commit version: 6f40acee 2022-09-09 17:37:44, build by: jenkins 2022-09-14 11:14:12
1970-01-01 00:00:13 opt_multi_version     = 1
1970-01-01 00:00:13 opt_bitmain_ab        = 1
1970-01-01 00:00:13 mid_auto_gen          = 1
1970-01-01 00:00:13 opt_bitmain_work_mode = 0
1970-01-01 00:00:13 port 427 already exported
1970-01-01 00:00:13 port 429 already exported
1970-01-01 00:00:13 port 431 already exported
1970-01-01 00:00:13 port 433 already exported
1970-01-01 00:00:13 no board pluged in socket 432
1970-01-01 00:00:13 port 434 already exported
1970-01-01 00:00:13 port 435 already exported
1970-01-01 00:00:13 port 447 already exported
1970-01-01 00:00:13 port 406 already exported
1970-01-01 00:00:13 Note: front fan is power on!
1970-01-01 00:00:13 Note: rear fan is power on!
1970-01-01 00:00:13 start the http log.
1970-01-01 00:00:13 httpListenThread start ret=0
1970-01-01 00:00:13 load machine BHB56801 conf
1970-01-01 00:00:13 start listen on 6060 ...
1970-01-01 00:00:13 machine : BHB56801 
1970-01-01 00:00:13 get test_loop_securely_find_asic_num failed
1970-01-01 00:00:18 power off
1970-01-01 00:00:19 ==========================capability start==========================
1970-01-01 00:00:19 board num = 3
1970-01-01 00:00:19 board id = 0, chain num = 1
1970-01-01 00:00:19 	chain id = 0
1970-01-01 00:00:19 board id = 1, chain num = 1
1970-01-01 00:00:19 	chain id = 1
1970-01-01 00:00:19 board id = 2, chain num = 1
1970-01-01 00:00:19 	chain id = 2
1970-01-01 00:00:19 ==========================capability end============================
1970-01-01 00:00:19 chain num = 3
1970-01-01 00:00:20 load chain 0 eeprom data
1970-01-01 00:00:20 board_info_version = 5
1970-01-01 00:00:20 algorithm_and_key_version = 0x11
1970-01-01 00:00:20 board_sn = BCMEYPDBCJBJC0BVZ
1970-01-01 00:00:20 chip_die = ED
1970-01-01 00:00:20 chip_marking = S1GH22CE0Q
1970-01-01 00:00:20 chip_bin = 3
1970-01-01 00:00:20 ft_version = F1V18B4C1
1970-01-01 00:00:20 pcb_version = 0x100
1970-01-01 00:00:20 bom_version = 0x20
1970-01-01 00:00:20 asic_sensor_type = 0x0
1970-01-01 00:00:20 asic_sensor_addr[0] = 0x0
1970-01-01 00:00:20 asic_sensor_addr[1] = 0x0
1970-01-01 00:00:20 asic_sensor_addr[2] = 0x0
1970-01-01 00:00:20 asic_sensor_addr[3] = 0x0
1970-01-01 00:00:20 pic_sensor_type = 0x0
1970-01-01 00:00:20 pic_sensor_addr = 0x0
1970-01-01 00:00:20 chip_tech = AG
1970-01-01 00:00:20 board_name = BHB56801
1970-01-01 00:00:20 factory_job = BCME20230301001-ZB
1970-01-01 00:00:20 board_info_crc = 0x2
1970-01-01 00:00:20 voltage = 1290
1970-01-01 00:00:20 frequency = 485
1970-01-01 00:00:20 nonce_rate = 9996
1970-01-01 00:00:20 pcb_temp_in = 34
1970-01-01 00:00:20 pcb_temp_out = 50
1970-01-01 00:00:20 test_version = 1
1970-01-01 00:00:20 test_standard = 0
1970-01-01 00:00:20 param_info_crc = 0x17
1970-01-01 00:00:20 pt1_result = 1
1970-01-01 00:00:20 pt1_count = 1
1970-01-01 00:00:21 pt2_result = 1
1970-01-01 00:00:21 pt2_count = 1
1970-01-01 00:00:21 sweep_hashrate = 0
1970-01-01 00:00:21 sweep_result = 0
1970-01-01 00:00:22 load chain 1 eeprom data
1970-01-01 00:00:22 board_info_version = 5
1970-01-01 00:00:22 algorithm_and_key_version = 0x11
1970-01-01 00:00:22 board_sn = BCMEYPDBCJBJC00A8
1970-01-01 00:00:22 chip_die = ED
1970-01-01 00:00:22 chip_marking = P1GH22BV0G
1970-01-01 00:00:22 chip_bin = 4
1970-01-01 00:00:22 ft_version = F1V14B3C1
1970-01-01 00:00:22 pcb_version = 0x100
1970-01-01 00:00:22 bom_version = 0x20
1970-01-01 00:00:22 asic_sensor_type = 0x0
1970-01-01 00:00:22 asic_sensor_addr[0] = 0x0
1970-01-01 00:00:22 asic_sensor_addr[1] = 0x0
1970-01-01 00:00:22 asic_sensor_addr[2] = 0x0
1970-01-01 00:00:22 asic_sensor_addr[3] = 0x0
1970-01-01 00:00:22 pic_sensor_type = 0x0
1970-01-01 00:00:22 pic_sensor_addr = 0x0
1970-01-01 00:00:22 chip_tech = AG
1970-01-01 00:00:22 board_name = BHB56801
1970-01-01 00:00:22 factory_job = BCME20230301001-ZB
1970-01-01 00:00:22 board_info_crc = 0x9
1970-01-01 00:00:22 voltage = 1290
1970-01-01 00:00:22 frequency = 485
1970-01-01 00:00:22 nonce_rate = 9998
1970-01-01 00:00:22 pcb_temp_in = 36
1970-01-01 00:00:22 pcb_temp_out = 50
1970-01-01 00:00:22 test_version = 1
1970-01-01 00:00:22 test_standard = 0
1970-01-01 00:00:22 param_info_crc = 0x1e
1970-01-01 00:00:22 pt1_result = 1
1970-01-01 00:00:22 pt1_count = 1
1970-01-01 00:00:22 pt2_result = 1
1970-01-01 00:00:22 pt2_count = 1
1970-01-01 00:00:22 sweep_hashrate = 0
1970-01-01 00:00:22 sweep_result = 0
1970-01-01 00:00:24 load chain 2 eeprom data
1970-01-01 00:00:24 board_info_version = 5
1970-01-01 00:00:24 algorithm_and_key_version = 0x11
1970-01-01 00:00:24 board_sn = BCMEYPDBCJBJC09WS
1970-01-01 00:00:24 chip_die = ED
1970-01-01 00:00:24 chip_marking = J1GH22BV07
1970-01-01 00:00:24 chip_bin = 5
1970-01-01 00:00:24 ft_version = F1V14B3C2
1970-01-01 00:00:24 pcb_version = 0x100
1970-01-01 00:00:24 bom_version = 0x20
1970-01-01 00:00:24 asic_sensor_type = 0x0
1970-01-01 00:00:24 asic_sensor_addr[0] = 0x0
1970-01-01 00:00:24 asic_sensor_addr[1] = 0x0
1970-01-01 00:00:24 asic_sensor_addr[2] = 0x0
1970-01-01 00:00:24 asic_sensor_addr[3] = 0x0
1970-01-01 00:00:24 pic_sensor_type = 0x0
1970-01-01 00:00:24 pic_sensor_addr = 0x0
1970-01-01 00:00:24 chip_tech = AG
1970-01-01 00:00:24 board_name = BHB56801
1970-01-01 00:00:24 factory_job = BCME20230301001-ZB
1970-01-01 00:00:24 board_info_crc = 0x1
1970-01-01 00:00:24 voltage = 1290
1970-01-01 00:00:24 frequency = 485
1970-01-01 00:00:24 nonce_rate = 9998
1970-01-01 00:00:24 pcb_temp_in = 35
1970-01-01 00:00:24 pcb_temp_out = 50
1970-01-01 00:00:24 test_version = 1
1970-01-01 00:00:24 test_standard = 0
1970-01-01 00:00:24 param_info_crc = 0x1d
1970-01-01 00:00:24 pt1_result = 1
1970-01-01 00:00:24 pt1_count = 1
1970-01-01 00:00:24 pt2_result = 1
1970-01-01 00:00:24 pt2_count = 1
1970-01-01 00:00:24 sweep_hashrate = 0
1970-01-01 00:00:24 sweep_result = 0
1970-01-01 00:00:24 eeprom load ret:0
1970-01-01 00:00:24 i2c_sim_init start
1970-01-01 00:00:24 power i2c device:sim_dev addr:0x10 fd:255
1970-01-01 00:00:24 i2c_sim_init end
1970-01-01 00:00:25 power open power_version = 0x76
1970-01-01 00:00:28 power is Calibrated
1970-01-01 00:00:29 miner_type:Antminer BHB56801
1970-01-01 00:00:30 updated miner type to: Antminer BHB56801
1970-01-01 00:00:30 miner:BHB56801,board_name:BHB56801
1970-01-01 00:00:30 create thread get_nonce_and_register_thread
1970-01-01 00:00:30 fixed working voltage = 1290
1970-01-01 00:00:30 Chain [0] PCB Version: 0x0100
1970-01-01 00:00:30 Chain [0] BOM Version: 0x0020
1970-01-01 00:00:30 Chain [1] PCB Version: 0x0100
1970-01-01 00:00:30 Chain [1] BOM Version: 0x0020
1970-01-01 00:00:30 Chain [2] PCB Version: 0x0100
1970-01-01 00:00:30 Chain [2] BOM Version: 0x0020
1970-01-01 00:00:30 Fan check passed.
1970-01-01 00:00:30 init fan pid target=50
1970-01-01 00:00:30 max sensor num = 4
1970-01-01 00:00:30 STATUS_INITED: soc init done!
1970-01-01 00:00:30 temperature_monitor_thread start...
2023-05-11 20:12:06 start to init...
2023-05-11 20:12:06 power sn:OLTT329BBAACJ6731
2023-05-11 20:12:06 enable_power_calibration,calibration date:211208.
2023-05-11 20:12:07 power type version: 0x0076
2023-05-11 20:12:08 disable power watchdog: 0x0000
2023-05-11 20:12:09 Initializing the power, please wait, this may take up to 2 minutes...
2023-05-11 20:12:55 Slept 30 seconds, diff = 1.
2023-05-11 20:13:05 set_voltage_by_steps to 1500.
2023-05-11 20:13:10 start up min temp by 75a = 17
2023-05-11 20:13:13 Chain[0]: find 4 asic, times 0
2023-05-11 20:13:15 Chain[0]: find 4 asic, times 1
2023-05-11 20:13:17 Chain[0]: find 4 asic, times 2
2023-05-11 20:13:17 Chain 0 only find 4 asic, will power off hash board 0
2023-05-11 20:13:17 ERROR_SOC_INIT: soc init failed!
2023-05-11 20:13:17 stop_mining: soc init failed!
2023-05-11 20:13:17 uninit_temp_info
2023-05-11 20:13:17 do not read temp anymore...
2023-05-11 20:13:17 cancel thread
2023-05-11 20:13:17 ****power off hashboard****
2023-05-11 20:13:17 temp monitor thread exit
2023-05-11 20:13:17 power off
2023-05-11 20:13:39 Version num 65536
2023-05-11 20:13:39 Mask num 0x1fffe000
2023-05-11 20:13:39 Note: addrInterval or corenum is not initialized.