S19 86th ERROR_SOC_INIT
Hello, i have this problem with 2 brand new s19 86th, never worked. I have updated with the new firmware, i have change the wire cables between the control board and hashboards and I even tried a new control board but none of theses fixed the issue. can you please give me some tips?
023-03-23 14:17:23 Open miner sn file /config/sn error
2023-03-23 14:17:23 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer S19 sn :
2023-03-23 14:17:24 This is fix-freq version
2023-03-23 14:17:24 Miner compile time: Mon Dec 26 17:10:01 CST 2022 type: Antminer S19
2023-03-23 14:17:24 commit version: f2ab6bc 2022-12-26 17:08:34, build by: jenkins 2022-12-26 17:22:17
2023-03-23 14:17:24 opt_multi_version = 1
2023-03-23 14:17:24 opt_bitmain_ab = 1
2023-03-23 14:17:24 mid_auto_gen = 1
2023-03-23 14:17:24 opt_bitmain_work_mode = 0
2023-03-23 14:17:24 port 439 already exported
2023-03-23 14:17:24 port 454 already exported
2023-03-23 14:17:24 port 440 already exported
2023-03-23 14:17:24 port 455 already exported
2023-03-23 14:17:24 port 441 already exported
2023-03-23 14:17:24 port 456 already exported
2023-03-23 14:17:24 port 438 already exported
2023-03-23 14:17:24 port 453 already exported
2023-03-23 14:17:24 port 446 already exported
2023-03-23 14:17:24 port 445 already exported
2023-03-23 14:17:24 Note: front fan is power on!
2023-03-23 14:17:24 Note: rear fan is power on!
2023-03-23 14:17:24 start the http log.
2023-03-23 14:17:24 httpListenThread start ret=0
2023-03-23 14:17:24 start listen on 6060 ...
2023-03-23 14:17:24 bad chain id = 3
2023-03-23 14:17:27 bad chain id = 3
2023-03-23 14:17:29 ==========================capability start==========================
2023-03-23 14:17:29 board num = 3
2023-03-23 14:17:29 board id = 0, chain num = 1
2023-03-23 14:17:29 chain id = 0
2023-03-23 14:17:29 board id = 1, chain num = 1
2023-03-23 14:17:29 chain id = 1
2023-03-23 14:17:29 board id = 2, chain num = 1
2023-03-23 14:17:29 chain id = 2
2023-03-23 14:17:29 ==========================capability end============================
2023-03-23 14:17:29 chain num = 3
2023-03-23 14:17:29 skip loading levels for now
2023-03-23 14:17:33 load chain 0 eeprom data
2023-03-23 14:17:36 load chain 1 eeprom data
2023-03-23 14:17:39 load chain 2 eeprom data
2023-03-23 14:17:39 multi machine mode
2023-03-23 14:17:39 load machine BHB42831 conf
2023-03-23 14:17:39 machine : BHB42831
2023-03-23 14:17:39 chain_num 4, chain_domain_num 44, chain_asic_num 88, domain_asic_num 2
2023-03-23 14:17:39 abandon mix board!
2023-03-23 14:17:39 abandon mix board!
2023-03-23 14:17:39 fan_eft : 0 fan_pwm : 100
2023-03-23 14:17:39 create thread get_nonce_and_register_thread
2023-03-23 14:17:39 fixed working voltage = 1530
2023-03-23 14:17:39 fixed frequency is 645
2023-03-23 14:17:39 Chain [0] PCB Version: 0x0100
2023-03-23 14:17:39 Chain [0] BOM Version: 0x0010
2023-03-23 14:17:39 Chain [1] PCB Version: 0x0100
2023-03-23 14:17:39 Chain [1] BOM Version: 0x0010
2023-03-23 14:17:39 Chain [2] PCB Version: 0x0100
2023-03-23 14:17:39 Chain [2] BOM Version: 0x0010
2023-03-23 14:17:39 bad chain id = 3
2023-03-23 14:17:39 Fan check passed.
2023-03-23 14:17:39 uart_trans addr:0xf714f000.
2023-03-23 14:17:39 max sensor num = 4
2023-03-23 14:17:39 STATUS_INITED: soc init done!
2023-03-23 14:17:39 temperature_monitor_thread start...
2023-03-23 14:17:41 start to init...
2023-03-23 14:17:41 i2c_sim_init start
2023-03-23 14:17:41 init gpio477
2023-03-23 14:17:41 init gpio476
2023-03-23 14:17:41 i2c_sim_init end
2023-03-23 14:17:43 power open power_version = 0x78
2023-03-23 14:17:45 power is not Calibrated
2023-03-23 14:17:45 warning:power is not calibration.
2023-03-23 14:17:47 power type version: 0x0078
2023-03-23 14:17:48 disable power watchdog: 0x0000
2023-03-23 14:17:49 Initializing the power, please wait, this may take up to 2 minutes...
2023-03-23 14:18:20 Slept 30 seconds, diff = 0.
2023-03-23 14:18:24 set_voltage_by_steps to 1700.
2023-03-23 14:18:33 start up min temp by 75a = 20
2023-03-23 14:18:36 Chain[0]: find 0 asic, times 0
2023-03-23 14:18:38 Chain[0]: find 0 asic, times 1
2023-03-23 14:18:40 Chain[0]: find 0 asic, times 2
2023-03-23 14:18:40 Chain 0 only find 0 asic, will power off hash board 0
2023-03-23 14:18:41 Chain[1]: find 0 asic, times 0
2023-03-23 14:18:43 Chain[1]: find 0 asic, times 1
2023-03-23 14:18:45 Chain[1]: find 0 asic, times 2
2023-03-23 14:18:45 Chain 1 only find 0 asic, will power off hash board 1
2023-03-23 14:18:46 Chain[2]: find 0 asic, times 0
2023-03-23 14:18:48 Chain[2]: find 0 asic, times 1
2023-03-23 14:18:50 Chain[2]: find 0 asic, times 2
2023-03-23 14:18:50 Chain 2 only find 0 asic, will power off hash board 2
2023-03-23 14:18:50 ERROR_SOC_INIT: soc init failed!
2023-03-23 14:18:50 stop_mining: soc init failed!
2023-03-23 14:18:50 uninit_temp_info
2023-03-23 14:18:50 do not read temp anymore...
2023-03-23 14:18:50 cancel thread
2023-03-23 14:18:50 ****power off hashboard****
2023-03-23 14:18:50 temp monitor thread exit
2023-03-23 14:19:17 Version num 65536
2023-03-23 14:19:17 Mask num 0x1fffe000
2023-03-23 14:19:17 opt_multi_version = 65536, interval timeout = 2397190
2023-03-23 14:19:17 freq = 645, percent = 90, hcn = 4064, timeout = 2397190
-
Dear customer.
From the kernel log, it can't detect the hashboard. please kindly exclude the issue by following steps:
1.Check the wires for the hashboard--pull them and re-plug them again, and also you can try to change the new wires.
2.Please clean up the dust.
How To Clean and Dust The Antminers
https://support.bitmain.com/hc/en-us/articles/115004520173-How-To-Clean-and-Dust-The-Antminers
If there are still the same problems after the above steps, please send it to repair.
Best regards
BITMAIN
-
Dear Customer,
If you have any questions please feel free to contact us.
Please send email to customersupport@bitmain.com
We will reply to your question as soon as possible.
-
S19j 86T
产品概述 规格参数
版本 S19j Pro
型号 240-Cb
加密算法/币种 SHA256/BTC/BCH
额定算力, TH/s 86 + 3%
墙上功耗@25℃, Watt 2967 ± 5%
能效比 @25°C, J/TH 34.5 ± 5%本公司为中国区域总代理商，感兴趣的老板可以踊跃联系我哦~ 期待后续的合作 我这边销售 代售 上机 托管 一站式服务，提供技术支持！订购热线【17779130177】
Yes, I am the general agent in China. If you need the machine ka3/k7, you can contact me and call me at +86 17779130177.
-
Dear Customer,
If you have any questions please feel free to contact us.
Please send email to customersupport@bitmain.com
We will reply to your question as soon as possible.
-
Dear Customer,
If you have any questions please feel free to contact us.
Please send email to customersupport@bitmain.com
We will reply to your question as soon as possible.
Please sign in to leave a comment.
Comments
6 comments