1.
Issue: The miner has no hash rate. One of the hash board’s temperature exceeds 80 degree Celsius.
Reason: A piece of heat sink is loose or dropped off.
Solution: Remove the hash board that exceeds 80 degree Celsius to repair.
Note: If large quantity of hash boards temperature exceeds 80 degree Celsius, please add cooling devices, as the high temperature will ultimately go into the high temperature protection mode and the miner will shut down. Moreover, the miner can easily get defective when working in a high temperature environment.
2.
Issue: The hash rate is good, but there is no temperature shown on the Miner status.
The hash board is easily burnt if there is no temperature shown for monitoring or when the real temperature is very high
Reason: The temperature detector is damaged on one of the hash boards that lead to the other two hash boards to have the issues on temperature display as well.
Solution: Test the 3 hash boards one by one by connecting to the control board and let it run for about 5 minutes, find the faulty hash board with temperature detection problem and ship it back to repair.
3.
Issue: The hash rate is lower than normal. There is an “X” shown on the Miner status.
Reason: The ASIC chip is damaged, which resulted in the loss of some hash rate on the hash board.
Solution: If that hash board can still work well, you can keep and continue to let it work. There is no need to repair it unless the hash board becomes totally defective.
4.
Issue: The hash rate is lower than normal. There are a lot of “X” shown on Miner status
Reason: The chips are damaged, which lead to the entire hash board running abnormally.
Solution: Remove the hash board to repair.
5.
Issue: The hash rate is lower than normal. There are a lot of “-” shown on Miner status
Reason: It may be caused by instability of the PSU voltage or a defective hash board.
Solution: Replace the PSU and control board-hash board 18 pin ribbon cable. If replacing didn't work, please remove the hash board to repair.
6.
Issue: The hash rate is lower than normal. Some chips are lost. The hash rate is only running at 2/3 of the normal.
Reason: Chain scission of chips
Solution: Remove the hash board to repair.
7.
Issue: The miner has no hash rate. There is X.X.X.X shown on the Hardware Version. Hash board cannot be detected. There is no information shown at all on the Miner status interface.
Cause: The firmware of miner is not detected.
Solution: Power off the miner and reset it. Reload the firmware.
8.
Issue: The miner worked great when it was powered. After awhile, there is no hash rate.
Reason: One of the fans is not detected. Miner will work well only when both fans are detected.
Solution: Switch the control board connection between the two fans to find out which one is defective.
9.
Issue: A large number of Antpools surfaced. Hash rate is normal. There is no use resetting the router.
Reason: One of the computers in the network has been infected by virus or malware.
Solution: Find infected computer and remove the virus or malware.
10.
Issue: Miner can’t find IP. Red light flashing; Green light does not blink
- Reason：The Miner is not connected with the Internet.
Solution: Test the Internet cable, connection and the settings of the Internet (DHCP mode is required).
- Reason: The miner program has not started.
Solution: Reset the miner several times.
- Reason: The application of miner is lost.
Solution: Perform control board recovery
11.
Issue: The miner doesn’t work after powering on despite changing the PSU.
- Reason: There is a short circuit inside one of the hash boards.
Solution: Find which hash board is defective. Remove the defective part to repair.
- Reason: Control board failure
Solution: Change the control board
12.
Issue: PSU can’t work when if the PSU fan is running. Miner works well after changing PSU.
Reason: The PSU is defective. The PSU fan is powered by a different output. The defect can’t be judged by whether the fan rotation power is normal.
Solution: Ship back the PSU to repair.
13.
Issue: Miner restores to factory setting after powering off.
Reason：The software in BB board is damaged.
Solution: Perform control board recovery
14.
Issue: Miners work well for several month before it starts to malfunction.
- Reason: The hash boards were corroded by humidity and lots of dust.
Solution: Remove the defective hash boards, dust the miner and reduce air humidity.
- Reason: Large amount of dust, resulting in congestion in the air duct. Heat can’t be dissipated. Catkins are likely to cause congestion in air duct.
Solution: Remove the defective hash boards, dust the miner and add dust elimination.
15.
Issue: The machine is defective when network changed
Reason: Due to the network setup, miner can’t find the IP.
Solution: Power off and reset the miner.
16.
Issue: S7 malfunction after running for a while. It runs again after rebooting.
-Reason: Temperature exceeds 80 degree Celsius and miner will automatically shut down.
Solution: Increase the amount of air flow.
- Reason: The PGA in BB board weld badly, which lead to miner’s shut down.
Solution: Remove the BB board to repair.
17.
Issue: PSU can’t work but fan is running. All the indicators are off.
Reason: The control board cannot get power as the power circuit in IO board is damaged.
Solution: Switch the BB Board and IO Board with good miner to troubleshoot the defective parts.
Comments
249 comments
i will appriciate if sb can help me it works only one of three hash boards on my s9. thank you
@Ftergiotis Vaggelis
unplug your miner,
wait for several minutes,
then power it on while pressing the IP report button,
and count 5 seconds,
then release the button.
it will reset your miner automatically, when you see the green status light blink, you can login into the back-end and change all your configuration, save & apply,
in most cases, 3 hash board will be back again.
hope you are the lucky one.
@Grand
Thank you very much for your kind reply
I did excatlty that you told me but now not even the status green light not bling and i cant get in even inside miner status on backstage. more over a red light r25 tf open on one of hashboard. i am really confused i tryied many times. any idea for this situation?
first of all, check all your data cable and power cable to make sure the connection is solidly.
when the miner is booting, you can see a red LED on each board goes on and off (in fact, it's two LEDs, very close), the three hash boards is doing self-check, maybe at the same time, maybe not, that is normal. after about 10 to 15 minutes, the LED on hash board will continuous light on, and the green LED on the panel will blink.
in this process, if any of the boards has an LED never light up, or lights out finally, this board will not work properly, if all 3 boards failure, maybe you need to replace the PSU with another normal working one, if you have.
I've had a similar situation, especially when you have lots of miners working at the same time, the power load may be unstable.
Hi,
Thank you for your fast apply my warranty.
I still have one big problem:
I bought 1 Antimer L3+ New with 6 month of warranty, As I received the antminer I start it and just few hours later it stops working due to a Defective fan.
Noone gave me specific way to fix the L3, apart copy and paste forum guide on how to fix, so I had to buy from china by aliexpress one replacment fan for L3 just to make a test and see if it works.
So basicly my L3 has arrived that was not working the 28 december 2017 and I was able to start use it just the 24 Gennuary 2018 so my antminer due to a defective fan (has arrived in that condition from factory) has burn 1 month of the total 6 of warranty, that's not fair at all to pay so much for a product and cannot use it for 1 month by the time my guarantiee was running.
To be totally fair to me you should add 1 month to my SN Antminer L3.
Best regard
Dear Japs85,
Thanks for your consultation!
Joy replied to you on Jan. 16 to ask you to test the fan.
You can buy the parts you need from our official website. As below,
https://shop.bitmain.com/part.htm
Sorry that we do not sell hashboards.
Note: Please read the description of the part carefully before you order it and make sure the part match your miner.
Order cancellation/refund request won't be accepted once order is confirmed.
Best regards
Jocelyn
Bitmain
Always order products directly from our website: www.bitmain.com
"Solved" means we replied - we still work on your issue until it is resolved.
Hi,
I'm sorry, but that's a joke?
You ship one New Item with faulty fan, and you ask me to make some test with some spare parts that I don't have? like test another PSU another I/O board?
So to test if it was the fan the problem you could provide me one instead of make me buy it (and it was just my personal idea that was the fan to make the antminer stop) from china so slow ship time because I won't pay for fast ship. It take to me 21 days to get replacement fan that you could provide me in 2 days, so you continue with saying things around the problem.
I am not open a warranty after 4 month of use... I ask for help 12 hrs later that I receved the antminer new from your factory.
I understand that you do NOT want to admit that you shipped me a faulty unit and you NEVER admit that in this way my antminer has 5 month of warranty and not 6.
Best regard
Thanks for your consultation!
You already tested it with the spare parts you have.
Please let us know if you have additional questions or concerns.
Best regards,
Jocelyn
Bitmain
Always order products directly from our website: www.bitmain.com
"Solved" means we replied - we still work on your issue until it is resolved.
Hi,
did you misunderstanding that:
- I've received the antminer 27/12/2017
- I've ask for support 28/12/2017
-I've paid for a replacement fan by my self and that has arrived 24/01/2018
during this time from 28/12/2017 to 24/01/2018 the antminer has never worked.
Dear Japs85,
Thanks for your consultation!
Please let us know if you have additional questions or concerns.
Best regards,
Jocelyn
Bitmain
easy, man, they always doing things like that, you know, I have bought over 12 thousand pcs of miner from them in the past 14 months, they always.
hello, issue8
On the overview, Hardware version is blank and the kernel log said 'bmminer not found, restart bmminer ..'
I check PSU : Ok 12.20v
I tried to cold start again
I tried to reboot by software
I tried to reset the firmware
I tried to flash with the first FW : Antminer-S9-all-201704270135-autofreq-user-Update2UBI-NF.tar.gz
I tried to flash with the last FW : Antminer-S9-all-201711171757-autofreq-user-Update2UBI-NF.tar.gz
The three red led on asics cards light on (no blink)
Does i need to make an repair ticket to send back ??
Miner Type Antminer S9
Hostname antMiner
Model GNU/Linux
Hardware Version
Kernel Version Linux 3.14.0-xilinx-ge8a2f71-dirty #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
File System Version Fri Nov 17 17:57:49 CST 2017
Logic Version S9_V2.55
BMminer Version
Uptime 3
Load Average 0.01, 0.03, 0.01
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB)
[ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB)
[ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB)
[ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000311] ps7-ttc #0 at df804000, irq=43
[ 0.000624] Console: colour dummy device 80x30
[ 0.000656] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040211] pid_max: default: 32768 minimum: 301
[ 0.040432] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040451] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.042624] CPU: Testing write buffer coherency: ok
[ 0.042974] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.043035] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[ 0.043262] L310 cache controller enabled
[ 0.043282] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.121041] CPU1: Booted secondary processor
[ 0.210230] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210364] Brought up 2 CPUs
[ 0.210383] SMP: Total of 2 processors activated.
[ 0.210392] CPU: All CPU(s) started in SVC mode.
[ 0.211063] devtmpfs: initialized
[ 0.213487] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214740] regulator-dummy: no parameters
[ 0.223746] NET: Registered protocol family 16
[ 0.226011] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.228345] cpuidle: using governor ladder
[ 0.228359] cpuidle: using governor menu
[ 0.235926] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.237463] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.237477] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.237596] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.260028] bio: create slab <bio-0> at 0
[ 0.261957] vgaarb: loaded
[ 0.262671] SCSI subsystem initialized
[ 0.263610] usbcore: registered new interface driver usbfs
[ 0.263784] usbcore: registered new interface driver hub
[ 0.264014] usbcore: registered new device driver usb
[ 0.264559] media: Linux media interface: v0.10
[ 0.264719] Linux video capture interface: v2.00
[ 0.264964] pps_core: LinuxPPS API ver. 1 registered
[ 0.264976] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.265100] PTP clock support registered
[ 0.265461] EDAC MC: Ver: 3.0.0
[ 0.266545] Advanced Linux Sound Architecture Driver Initialized.
[ 0.269554] DMA-API: preallocated 4096 debug entries
[ 0.269569] DMA-API: debugging enabled by kernel config
[ 0.269660] Switched to clocksource arm_global_timer
[ 0.290478] NET: Registered protocol family 2
[ 0.291170] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.291228] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.291313] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.291359] TCP: reno registered
[ 0.291376] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.291412] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.291667] NET: Registered protocol family 1
[ 0.292030] RPC: Registered named UNIX socket transport module.
[ 0.292042] RPC: Registered udp transport module.
[ 0.292051] RPC: Registered tcp transport module.
[ 0.292059] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.292073] PCI: CLS 0 bytes, default 64
[ 0.292550] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.294645] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.296824] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.297035] msgmni has been set to 967
[ 0.297856] io scheduler noop registered
[ 0.297869] io scheduler deadline registered
[ 0.297907] io scheduler cfq registered (default)
[ 0.308918] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.308938] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.434525] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 1.001983] console [ttyPS0] enabled
[ 1.006238] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.013885] [drm] Initialized drm 1.1.0 20060810
[ 1.031035] brd: module loaded
[ 1.040515] loop: module loaded
[ 1.050320] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.056068] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.064118] libphy: XEMACPS mii bus: probed
[ 1.068491] ------------- phy_id = 0x3625e62
[ 1.073430] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.082045] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.088664] ehci-pci: EHCI PCI platform driver
[ 1.095909] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.102862] usbcore: registered new interface driver usb-storage
[ 1.109734] mousedev: PS/2 mouse device common for all mice
[ 1.115862] i2c /dev entries driver
[ 1.122784] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.128266] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.134205] Xilinx Zynq CpuIdle Driver started
[ 1.139051] sdhci: Secure Digital Host Controller Interface driver
[ 1.145182] sdhci: Copyright(c) Pierre Ossman
[ 1.149483] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.156395] mmc0: no vqmmc regulator found
[ 1.160436] mmc0: no vmmc regulator found
[ 1.199677] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.208366] usbcore: registered new interface driver usbhid
[ 1.213878] usbhid: USB HID core driver
[ 1.218629] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.224928] nand: Micron MT29F2G08ABAEAWP
[ 1.228890] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.234837] Bad block table found at page 131008, version 0x01
[ 1.241056] Bad block table found at page 130944, version 0x01
[ 1.247109] 3 ofpart partitions found on MTD device pl353-nand
[ 1.252892] Creating 3 MTD partitions on "pl353-nand":
[ 1.257986] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.266044] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.273383] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.282399] TCP: cubic registered
[ 1.285633] NET: Registered protocol family 17
[ 1.290357] Registering SWP/SWPB emulation handler
[ 1.296270] regulator-dummy: disabling
[ 1.300697] UBI: attaching mtd1 to ubi0
[ 1.823622] UBI: scanning is finished
[ 1.835304] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.842385] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.849127] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.855830] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.862689] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.868657] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.875788] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1134783803
[ 1.884819] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.894037] UBI: background thread "ubi_bgt0d" started, PID 1080
[ 1.894043] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.898057] ALSA device list:
[ 1.898061] No soundcards found.
[ 1.914470] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[ 1.975638] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.981600] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.990703] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 2.000587] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 2.005617] UBIFS: media format: w4/r0 (latest is w4/r0), UUID B079DD56-06BB-4E31-8F5E-A6604F480DB2, small LPT model
[ 2.017375] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.024835] devtmpfs: mounted
[ 2.027943] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[ 2.870937] random: dd urandom read with 0 bits of entropy available
[ 3.269682]
[ 3.269682] bcm54xx_config_init
[ 3.879699]
[ 3.879699] bcm54xx_config_init
[ 6.880517] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 6.886610] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 19.477144] In axi fpga driver!
[ 19.480254] request_mem_region OK!
[ 19.483611] AXI fpga dev virtual address is 0xdf9fc000
[ 19.488716] *base_vir_addr = 0x8c510
[ 19.505188] In fpga mem driver!
[ 19.508263] request_mem_region OK!
[ 19.511874] fpga mem virtual address is 0xe2000000
[ 20.329682]
[ 20.329682] bcm54xx_config_init
[ 20.969712]
[ 20.969712] bcm54xx_config_init
[ 23.970569] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 23.976587] xemacps e000b000.ps7-ethernet: link up (100/FULL)
This is XILINX board. Totalram: 507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 8002ecc67680881c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[30] has core num=2
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Chain[7] ASIC[42] has core num=12
Check chain[7] PIC fw version=0x03
get PIC voltage=125 on chain[5], value=870
get PIC voltage=91 on chain[6], value=890
get PIC voltage=125 on chain[7], value=870
set_reset_allhashboard = 0x00000000
chain[5] temp offset record: 62,-3,0,0,0,0,33,0
chain[5] temp chip I2C addr=0x98
chain[6] temp offset record: 62,-4,0,0,0,0,33,0
chain[6] temp chip I2C addr=0x98
chain[7] temp offset record: 62,-5,0,0,0,0,33,0
chain[7] temp chip I2C addr=0x98
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL
--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 1 times, completed chain = 3, total chain num = 3
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1378 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Fri Nov 17 17:57:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 8002ecc67680881c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=6120
get fan[2] speed=6120
get fan[2] speed=6120
get fan[2] speed=6120
get fan[2] speed=6120
get fan[2] speed=6120
get fan[5] speed=4440
get fan[2] speed=6120
get fan[5] speed=4440
get fan[2] speed=6120
get fan[5] speed=4440
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J6] has backup chain_voltage=870
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J7] has backup chain_voltage=890
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J8] has backup chain_voltage=870
Check chain[7] PIC fw version=0x03
Chain[J6] orignal chain_voltage_pic=125 value=870
Chain[J7] orignal chain_voltage_pic=91 value=890
Chain[J8] orignal chain_voltage_pic=125 value=870
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[30] has core num=2
Chain[J7] has core num in PIC
Chain[J8] has core num in PIC
Chain[J8] ASIC[42] has core num=12
miner total rate=13902GH/s fixed rate=13500GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=-3
Chain:5 base freq=650
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650
Chain:5 max freq=650
Chain:5 min freq=650
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=-4
Chain:6 base freq=631
Asic[ 0]:631
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631
Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631
Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631
Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631
Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631
Chain:6 max freq=631
Chain:6 min freq=631
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=-5
Chain:7 base freq=656
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:656
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 Asic[48]:656
Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 Asic[56]:656
Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656
Chain:7 max freq=656
Chain:7 min freq=656
Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=-3
Chain:5 base freq=650
Asic[ 0]:631
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:637
Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637 Asic[40]:637
Asic[41]:637 Asic[42]:637 Asic[43]:637 Asic[44]:637 Asic[45]:637 Asic[46]:637 Asic[47]:637 Asic[48]:637
Asic[49]:637 Asic[50]:637 Asic[51]:637 Asic[52]:637 Asic[53]:637 Asic[54]:637 Asic[55]:637 Asic[56]:637
Asic[57]:637 Asic[58]:637 Asic[59]:637 Asic[60]:637 Asic[61]:637 Asic[62]:637
Chain:5 max freq=637
Chain:5 min freq=631
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=-4
Chain:6 base freq=631
Asic[ 0]:631
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631
Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631
Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631
Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631
Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631
Chain:6 max freq=631
Chain:6 min freq=631
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=-5
Chain:7 base freq=656
Asic[ 0]:631
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637
Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637
Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637 Asic[40]:637
Asic[41]:637 Asic[42]:637 Asic[43]:637 Asic[44]:637 Asic[45]:637 Asic[46]:637 Asic[47]:637 Asic[48]:637
Asic[49]:637 Asic[50]:637 Asic[51]:637 Asic[52]:637 Asic[53]:637 Asic[54]:637 Asic[55]:637 Asic[56]:637
Asic[57]:637 Asic[58]:637 Asic[59]:637 Asic[60]:637 Asic[61]:637 Asic[62]:637
Chain:7 max freq=637
Chain:7 min freq=631
max freq = 637
set baud=1
Chain[J6] PIC temp offset=62,-3,0,0,0,0,33,0
chain[5] temp chip I2C addr=0x98
Chain[J6] chip[244] use PIC middle temp offset=-3 typeID=55
New offset Chain[5] chip[244] local:18 remote:21 offset:26
Chain[J6] chip[244] get middle temp offset=26 typeID=55
Chain[J7] PIC temp offset=62,-4,0,0,0,0,33,0
chain[6] temp chip I2C addr=0x98
Chain[J7] chip[244] use PIC middle temp offset=-4 typeID=55
New offset Chain[6] chip[244] local:16 remote:18 offset:27
Chain[J7] chip[244] get middle temp offset=27 typeID=55
Chain[J8] PIC temp offset=62,-5,0,0,0,0,33,0
chain[7] temp chip I2C addr=0x98
Chain[J8] chip[244] use PIC middle temp offset=-5 typeID=55
New offset Chain[7] chip[244] local:17 remote:21 offset:25
Chain[J8] chip[244] get middle temp offset=25 typeID=55
single board rate=4551 voltage limit=890 on chain[5]
get PIC voltage=870 on chain[5], check: must be < 890
single board rate=4531 voltage limit=890 on chain[6]
get PIC voltage=890 on chain[6], check: must be < 890
single board rate=4552 voltage limit=890 on chain[7]
get PIC voltage=870 on chain[7], check: must be < 890
Chain[J6] set working voltage=870 [125]
Chain[J7] set working voltage=890 [91]
Chain[J8] set working voltage=870 [125]
do heat board 8xPatten for 1 times
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
do read_temp_func once...
do check_asic_reg 0x08
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=55 middle offset=26
Chain[5] Chip[62] local Temp=34
Chain[5] Chip[62] middle Temp=46
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=27
Chain[6] Chip[62] local Temp=33
Chain[6] Chip[62] middle Temp=47
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=25
Chain[7] Chip[62] local Temp=33
Chain[7] Chip[62] middle Temp=47
Done read temp on Chain[7]
set FAN speed according to: temp_highest=34 temp_top1[PWM_T]=34 temp_top1[TEMP_POS_LOCAL]=34 temp_change=4 fix_fan_steps=0
set normal FAN speed...
FAN PWM: 20
read_temp_func Done!
CRC error counter=0
I think you need more patience, uptime only 3 minutes, maybe 15 minutes for the first starting of firmware update, and 7 minutes for soft rebooting is normal.
Hi Grand,
I wait more than 2 hours, but nothing better. Miner not run :((
that's tooooooo bad, keep trying upgrade firmware and reset....
Good news, Miner start.
Exactly, i dont know I do. That 's strange.
I remove all plug to from hashboard and re-plug it
I flash a new time with the last Firmware
and... and i change the pool for slushpool. test it ok and come back to antpool.
Now it's run. I need to stop it at 06h00 GMT. When I must restart later, i will pray to Bit_God :))
I save the kernel log to compare.
Yes, it's true. You need to wait 5-7 minutes to see the Status_Miner panel.
I'm having a problem with Chain 6 on my S9. It doesn't work at all. I want to try to find a way to fix this without sending it back to bitmain. Here is a screenshot. Also when I look at my miner one of the hash boards doesn't have a red light on unlike the other two. Is there a way I can fix it myself.
@b.leterrier
glad to hear that, I don't know either, but I've tried to recover this way many times.
@Tdotjoe
you need to cold start, or upgrade the firmware and let it restart automatically, it looks like no big problem, no need to return to factory.
@Grand, thank you for your help. I just tried to download the newest firmware and nothing changed with chain 6. When I flashed the firmware all I got was a bunch of code after waiting a minute.
you can unplug all 3 boards' 12V power plug, then plug 3 connectors originally from the good ones back to chain 6, remain the other 2 boards (6 connectors) disconnected, then power on the miner, if this make chain 6 work, you need to check the PSU.
New original Antminer S9 14TH/s + PSU 1600W APW3++ Bitcoin ASIC Miner cost 1000usd
New 2018 Hot sale Baikal Giant B with PSU Dash Coin Miner cost 4000USD
Antminer D3 cost $1,100 each unit including PSU and delivery to your home address.
Baikal giant 10 2000usd each unit including PSU and delivery to your home address.
Antminer A3 840 3000USDeach unit including PSU and delivery to your home address.
Antminer L3+ cost $900 each unit including PSU and delivery to your home address.
Delivery takes just 2-3 daysto your home doorstep through FedEx,Ups or Dhl shipping courier services.
We accept payment through Western Union or Money Gram Transfer and also Bank transfer and BTC .
IF YOU ARE READY TO PLACE ORDER AND FOR QUICK REPONSE CONTACT US HERE:
Whatsapp CHAT or Call : +19842085304
Skype: faisa.hassan102
Best Regards
CEO
New original Antminer S9 14TH/s + PSU 1600W APW3++ Bitcoin ASIC Miner cost 1000usd
New 2018 Hot sale Baikal Giant B with PSU Dash Coin Miner cost 4000USD
Antminer D3 cost $1,100 each unit including PSU and delivery to your home address.
Baikal giant 10 2000usd each unit including PSU and delivery to your home address.
Antminer A3 840 3000USDeach unit including PSU and delivery to your home address.
Antminer L3+ cost $900 each unit including PSU and delivery to your home address.
Delivery takes just 2-3 daysto your home doorstep through FedEx,Ups or Dhl shipping courier services.
We accept payment through Western Union or Money Gram Transfer and also Bank transfer and BTC .
IF YOU ARE READY TO PLACE ORDER AND FOR QUICK REPONSE CONTACT US HERE:
Whatsapp CHAT or Call : +19842085304
Skype: faisa.hassan102
Best Regards
CEO
Hi Guys, i've recieved last monday my 6 Antminers S9. 3 of then have a problem, the 1st of them had a pin on the hashingboard which was corroded and rusty. For that one i have a repair ticket already.
The 2nd has a chain siccision on 1 hashingboard and it's running right now at about 2/3 of capacity.That one i will aswell send to repair.
And the 3rd one is a real problemchild. It was running aswell on 2/3 of its capacity. And it was showing me that the middle hashingboard had only 15° instead of around 75° like the other both hashinboards. So i reset and reinstall that Miner and since then its not working at all.
The KernelLog is showing me since:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB)
[ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB)
[ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB)
[ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000310] ps7-ttc #0 at df804000, irq=43
[ 0.000618] Console: colour dummy device 80x30
[ 0.000649] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040207] pid_max: default: 32768 minimum: 301
[ 0.040427] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040448] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.042589] CPU: Testing write buffer coherency: ok
[ 0.042922] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.042981] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[ 0.043205] L310 cache controller enabled
[ 0.043225] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.121034] CPU1: Booted secondary processor
[ 0.210227] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210355] Brought up 2 CPUs
[ 0.210375] SMP: Total of 2 processors activated.
[ 0.210383] CPU: All CPU(s) started in SVC mode.
[ 0.211042] devtmpfs: initialized
[ 0.213452] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214668] regulator-dummy: no parameters
[ 0.222350] NET: Registered protocol family 16
[ 0.224647] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.226935] cpuidle: using governor ladder
[ 0.226949] cpuidle: using governor menu
[ 0.234393] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.235913] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.235927] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.236038] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.258228] bio: create slab <bio-0> at 0
[ 0.259622] vgaarb: loaded
[ 0.260408] SCSI subsystem initialized
[ 0.261307] usbcore: registered new interface driver usbfs
[ 0.261476] usbcore: registered new interface driver hub
[ 0.261707] usbcore: registered new device driver usb
[ 0.262222] media: Linux media interface: v0.10
[ 0.262377] Linux video capture interface: v2.00
[ 0.262618] pps_core: LinuxPPS API ver. 1 registered
[ 0.262630] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.262760] PTP clock support registered
[ 0.263119] EDAC MC: Ver: 3.0.0
[ 0.264162] Advanced Linux Sound Architecture Driver Initialized.
[ 0.267028] DMA-API: preallocated 4096 debug entries
[ 0.267042] DMA-API: debugging enabled by kernel config
[ 0.267120] Switched to clocksource arm_global_timer
[ 0.287227] NET: Registered protocol family 2
[ 0.287883] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.287941] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.288026] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.288073] TCP: reno registered
[ 0.288090] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.288123] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.288353] NET: Registered protocol family 1
[ 0.288702] RPC: Registered named UNIX socket transport module.
[ 0.288714] RPC: Registered udp transport module.
[ 0.288722] RPC: Registered tcp transport module.
[ 0.288730] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.288743] PCI: CLS 0 bytes, default 64
[ 0.289177] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.291233] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.293339] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.293533] msgmni has been set to 967
[ 0.294323] io scheduler noop registered
[ 0.294336] io scheduler deadline registered
[ 0.294374] io scheduler cfq registered (default)
[ 0.304641] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.304662] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.427301] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 0.995313] console [ttyPS0] enabled
[ 0.999596] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.007253] [drm] Initialized drm 1.1.0 20060810
[ 1.024270] brd: module loaded
[ 1.033649] loop: module loaded
[ 1.042949] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.048828] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.056708] libphy: XEMACPS mii bus: probed
[ 1.061259] ------------- phy_id = 0x3625e62
[ 1.066005] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.074657] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.081555] ehci-pci: EHCI PCI platform driver
[ 1.088789] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.095588] usbcore: registered new interface driver usb-storage
[ 1.102488] mousedev: PS/2 mouse device common for all mice
[ 1.108616] i2c /dev entries driver
[ 1.115526] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.121048] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.126931] Xilinx Zynq CpuIdle Driver started
[ 1.131818] sdhci: Secure Digital Host Controller Interface driver
[ 1.138007] sdhci: Copyright(c) Pierre Ossman
[ 1.142274] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.149092] mmc0: no vqmmc regulator found
[ 1.153102] mmc0: no vmmc regulator found
[ 1.197141] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.205846] usbcore: registered new interface driver usbhid
[ 1.211357] usbhid: USB HID core driver
[ 1.216076] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.222375] nand: Micron MT29F2G08ABAEAWP
[ 1.226343] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.232281] Bad block table found at page 131008, version 0x01
[ 1.238501] Bad block table found at page 130944, version 0x01
[ 1.244552] 3 ofpart partitions found on MTD device pl353-nand
[ 1.250332] Creating 3 MTD partitions on "pl353-nand":
[ 1.255424] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.263467] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.270776] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.279725] TCP: cubic registered
[ 1.282964] NET: Registered protocol family 17
[ 1.287679] Registering SWP/SWPB emulation handler
[ 1.293563] regulator-dummy: disabling
[ 1.297928] UBI: attaching mtd1 to ubi0
[ 1.824749] UBI: scanning is finished
[ 1.836389] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.843466] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.850227] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.856892] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.863770] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.869750] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.876857] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1283732989
[ 1.885900] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.895117] UBI: background thread "ubi_bgt0d" started, PID 1080
[ 1.895123] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.899061] ALSA device list:
[ 1.899064] No soundcards found.
[ 1.915481] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[ 1.974130] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.980091] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.989194] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 1.999079] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 2.004107] UBIFS: media format: w4/r0 (latest is w4/r0), UUID C72F8006-6DFF-46BA-BBE9-380960A89F92, small LPT model
[ 2.015637] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.023060] devtmpfs: mounted
[ 2.026164] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[ 2.862910] random: dd urandom read with 0 bits of entropy available
[ 3.257146]
[ 3.257146] bcm54xx_config_init
[ 3.867170]
[ 3.867170] bcm54xx_config_init
[ 7.867988] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 7.874098] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[ 22.451449] In axi fpga driver!
[ 22.454520] request_mem_region OK!
[ 22.457942] AXI fpga dev virtual address is 0xdf9fc000
[ 22.463018] *base_vir_addr = 0x8c510
[ 22.478322] In fpga mem driver!
[ 22.481394] request_mem_region OK!
[ 22.484957] fpga mem virtual address is 0xe2000000
[ 23.276547]
[ 23.276547] bcm54xx_config_init
[ 23.906517]
[ 23.906517] bcm54xx_config_init
[ 27.906956] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 27.913058] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[ 933.522344] random: nonblocking pool is initialized
This is XILINX board. Totalram: 507527168
Detect 512MB control board of XILINX
Find Force Freq=600 will search Freq again!
DETECT HW version=0008c510
miner ID : 8164942e2420881c
config file found, will disable freq setting.
Miner Type = S9
AsicType = 1387
real AsicNum = 63
Find /tmp/searcherror: T7:1 The last log is below:
This is XILINX board. Totalram: 507527168
Detect 512MB control board of XILINX
Find Force Freq=600 will search Freq again!
DETECT HW version=0008c510
miner ID : 8164942e2420881c
config file found, will disable freq setting.
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Start search freq on chain[5]...
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Start search freq on chain[6]...
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Start search freq on chain[7]...
Check chain[7] PIC fw version=0x03
get PIC voltage=91 on chain[5], value=890
get PIC voltage=91 on chain[6], value=890
get PIC voltage=91 on chain[7], value=890
set voltage=870 search freq on chain[5]
now set pic voltage=125 on chain[5]
set voltage=870 search freq on chain[6]
now set pic voltage=125 on chain[6]
set voltage=870 search freq on chain[7]
now set pic voltage=125 on chain[7]
enable_pic_dac on chain[5]
enable_pic_dac on chain[6]
enable_pic_dac on chain[7]
set_reset_allhashboard = 0x00000000
chain[5] temp offset record: 62,0,0,0,0,0,36,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
chain[6] temp offset record: 62,0,0,0,0,0,36,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,36,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL
--- check asic number
check chain[5]: asicNum = 63
check chain[6]: asicNum = 63
check chain[7]: asicNum = 63
After Get ASIC NUM CRC error counter=0
set_baud=0
SEARCH_FREQ_TEST_LEVEL mode set freq=650 voltage=870 on chain[5]
SEARCH_FREQ_TEST_LEVEL mode set freq=650 voltage=870 on chain[6]
SEARCH_FREQ_TEST_LEVEL mode set freq=650 voltage=870 on chain[7]
The min freq=650
set real timeout 56, need sleep=408576
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
get send work num :57456 on Chain[5]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[7]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456
freq[00]=650 freq[01]=650 freq[02]=650 freq[03]=650 freq[04]=650 freq[05]=650 freq[06]=650 freq[07]=650
freq[08]=650 freq[09]=650 freq[10]=650 freq[11]=650 freq[12]=650 freq[13]=650 freq[14]=650 freq[15]=650
freq[16]=650 freq[17]=650 freq[18]=650 freq[19]=650 freq[20]=650 freq[21]=650 freq[22]=650 freq[23]=650
freq[24]=650 freq[25]=650 freq[26]=650 freq[27]=650 freq[28]=650 freq[29]=650 freq[30]=650 freq[31]=650
freq[32]=650 freq[33]=650 freq[34]=650 freq[35]=650 freq[36]=650 freq[37]=650 freq[38]=650 freq[39]=650
freq[40]=650 freq[41]=650 freq[42]=650 freq[43]=650 freq[44]=650 freq[45]=650 freq[46]=650 freq[47]=650
freq[48]=650 freq[49]=650 freq[50]=650 freq[51]=650 freq[52]=650 freq[53]=650 freq[54]=650 freq[55]=650
freq[56]=650 freq[57]=650 freq[58]=650 freq[59]=650 freq[60]=650 freq[61]=650 freq[62]=650
total valid nonce number:55482
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:13547
last_nonce_num:3033
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
freq[00]=650 freq[01]=650 freq[02]=650 freq[03]=650 freq[04]=650 freq[05]=650 freq[06]=650 freq[07]=650
freq[08]=650 freq[09]=650 freq[10]=650 freq[11]=650 freq[12]=650 freq[13]=650 freq[14]=650 freq[15]=650
freq[16]=650 freq[17]=650 freq[18]=650 freq[19]=650 freq[20]=650 freq[21]=650 freq[22]=650 freq[23]=650
freq[24]=650 freq[25]=650 freq[26]=650 freq[27]=650 freq[28]=650 freq[29]=650 freq[30]=650 freq[31]=650
freq[32]=650 freq[33]=650 freq[34]=650 freq[35]=650 freq[36]=650 freq[37]=650 freq[38]=650 freq[39]=650
freq[40]=650 freq[41]=650 freq[42]=650 freq[43]=650 freq[44]=650 freq[45]=650 freq[46]=650 freq[47]=650
freq[48]=650 freq[49]=650 freq[50]=650 freq[51]=650 freq[52]=650 freq[53]=650 freq[54]=650 freq[55]=650
freq[56]=650 freq[57]=650 freq[58]=650 freq[59]=650 freq[60]=650 freq[61]=650 freq[62]=650
total valid nonce number:0
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:0
last_nonce_num:0
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
freq[00]=650 freq[01]=650 freq[02]=650 freq[03]=650 freq[04]=650 freq[05]=650 freq[06]=650 freq[07]=650
freq[08]=650 freq[09]=650 freq[10]=650 freq[11]=650 freq[12]=650 freq[13]=650 freq[14]=650 freq[15]=650
freq[16]=650 freq[17]=650 freq[18]=650 freq[19]=650 freq[20]=650 freq[21]=650 freq[22]=650 freq[23]=650
freq[24]=650 freq[25]=650 freq[26]=650 freq[27]=650 freq[28]=650 freq[29]=650 freq[30]=650 freq[31]=650
freq[32]=650 freq[33]=650 freq[34]=650 freq[35]=650 freq[36]=650 freq[37]=650 freq[38]=650 freq[39]=650
freq[40]=650 freq[41]=650 freq[42]=650 freq[43]=650 freq[44]=650 freq[45]=650 freq[46]=650 freq[47]=650
freq[48]=650 freq[49]=650 freq[50]=650 freq[51]=650 freq[52]=650 freq[53]=650 freq[54]=650 freq[55]=650
freq[56]=650 freq[57]=650 freq[58]=650 freq[59]=650 freq[60]=650 freq[61]=650 freq[62]=650
total valid nonce number:57331
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:13997
last_nonce_num:2933
checkBoardState chain[5] rate=4334 bad_chip_num=4 lowest rate=4666 ret=1
checkBoardState chain[6] rate=0 bad_chip_num=63 lowest rate=4666 ret=1
checkBoardState chain[7] rate=4644 bad_chip_num=0 lowest rate=4666 ret=0
Detect Higher Rate = 4644 > 0 on chain[7] freq=650 voltage=870
After TEST CRC error counter=0
check FAN Speed: fan[2] speed=5880
check FAN Speed: fan[5] speed=5400
check FAN OK: fan num=2
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 1 times, completed chain = 0, total chain num = 3
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL
--- check asic number
check chain[5]: asicNum = 63
check chain[6]: asicNum = 63
check chain[7]: asicNum = 63
After Get ASIC NUM CRC error counter=0
set_baud=0
SEARCH_FREQ_TEST_LEVEL mode set freq=631 voltage=890 on chain[5]
SEARCH_FREQ_TEST_LEVEL mode set freq=631 voltage=890 on chain[6]
SEARCH_FREQ_TEST_UPONESTEP mode set freq=656 voltage=870 on chain[7]
The min freq=631
set real timeout 58, need sleep=423168
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
get send work num :57456 on Chain[5]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[7]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456
freq[00]=631 freq[01]=631 freq[02]=631 freq[03]=631 freq[04]=631 freq[05]=631 freq[06]=631 freq[07]=631
freq[08]=631 freq[09]=631 freq[10]=631 freq[11]=631 freq[12]=631 freq[13]=631 freq[14]=631 freq[15]=631
freq[16]=631 freq[17]=631 freq[18]=631 freq[19]=631 freq[20]=631 freq[21]=631 freq[22]=631 freq[23]=631
freq[24]=631 freq[25]=631 freq[26]=631 freq[27]=631 freq[28]=631 freq[29]=631 freq[30]=631 freq[31]=631
freq[32]=631 freq[33]=631 freq[34]=631 freq[35]=631 freq[36]=631 freq[37]=631 freq[38]=631 freq[39]=631
freq[40]=631 freq[41]=631 freq[42]=631 freq[43]=631 freq[44]=631 freq[45]=631 freq[46]=631 freq[47]=631
freq[48]=631 freq[49]=631 freq[50]=631 freq[51]=631 freq[52]=631 freq[53]=631 freq[54]=631 freq[55]=631
freq[56]=631 freq[57]=631 freq[58]=631 freq[59]=631 freq[60]=631 freq[61]=631 freq[62]=631
total valid nonce number:57260
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:13533
last_nonce_num:2713
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
freq[00]=631 freq[01]=631 freq[02]=631 freq[03]=631 freq[04]=631 freq[05]=631 freq[06]=631 freq[07]=631
freq[08]=631 freq[09]=631 freq[10]=631 freq[11]=631 freq[12]=631 freq[13]=631 freq[14]=631 freq[15]=631
freq[16]=631 freq[17]=631 freq[18]=631 freq[19]=631 freq[20]=631 freq[21]=631 freq[22]=631 freq[23]=631
freq[24]=631 freq[25]=631 freq[26]=631 freq[27]=631 freq[28]=631 freq[29]=631 freq[30]=631 freq[31]=631
freq[32]=631 freq[33]=631 freq[34]=631 freq[35]=631 freq[36]=631 freq[37]=631 freq[38]=631 freq[39]=631
freq[40]=631 freq[41]=631 freq[42]=631 freq[43]=631 freq[44]=631 freq[45]=631 freq[46]=631 freq[47]=631
freq[48]=631 freq[49]=631 freq[50]=631 freq[51]=631 freq[52]=631 freq[53]=631 freq[54]=631 freq[55]=631
freq[56]=631 freq[57]=631 freq[58]=631 freq[59]=631 freq[60]=631 freq[61]=631 freq[62]=631
total valid nonce number:0
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:0
last_nonce_num:0
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
freq[00]=656 freq[01]=656 freq[02]=656 freq[03]=656 freq[04]=656 freq[05]=656 freq[06]=656 freq[07]=656
freq[08]=656 freq[09]=656 freq[10]=656 freq[11]=656 freq[12]=656 freq[13]=656 freq[14]=656 freq[15]=656
freq[16]=656 freq[17]=656 freq[18]=656 freq[19]=656 freq[20]=656 freq[21]=656 freq[22]=656 freq[23]=656
freq[24]=656 freq[25]=656 freq[26]=656 freq[27]=656 freq[28]=656 freq[29]=656 freq[30]=656 freq[31]=656
freq[32]=656 freq[33]=656 freq[34]=656 freq[35]=656 freq[36]=656 freq[37]=656 freq[38]=656 freq[39]=656
freq[40]=656 freq[41]=656 freq[42]=656 freq[43]=656 freq[44]=656 freq[45]=656 freq[46]=656 freq[47]=656
freq[48]=656 freq[49]=656 freq[50]=656 freq[51]=656 freq[52]=656 freq[53]=656 freq[54]=656 freq[55]=656
freq[56]=656 freq[57]=656 freq[58]=656 freq[59]=656 freq[60]=656 freq[61]=656 freq[62]=656
total valid nonce number:57333
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:14134
last_nonce_num:3016
checkBoardState chain[5] rate=4499 bad_chip_num=0 lowest rate=4500 ret=0
Detect Higher Rate = 4499 > 0 on chain[5] freq=631 voltage=890
checkBoardState chain[6] rate=0 bad_chip_num=63 lowest rate=4500 ret=1
checkBoardState chain[7] rate=4689 bad_chip_num=0 lowest rate=4666 ret=2
SEARCH_FREQ_TEST_UPONESTEP get BOARD_FREQ_OK on chain[7]
special fix hash_voltage pic value = 125 [870] of Chain[7], voladded=0
Write freq to PIC :
Freq[00]=656
Freq[01]=656 Freq[02]=656 Freq[03]=656 Freq[04]=656 Freq[05]=656 Freq[06]=656 Freq[07]=656
Freq[08]=656 Freq[09]=656 Freq[10]=656 Freq[11]=656 Freq[12]=656 Freq[13]=656 Freq[14]=656
Freq[15]=656 Freq[16]=656 Freq[17]=656 Freq[18]=656 Freq[19]=656 Freq[20]=656 Freq[21]=656
Freq[22]=656 Freq[23]=656 Freq[24]=656 Freq[25]=656 Freq[26]=656 Freq[27]=656 Freq[28]=656
Freq[29]=656 Freq[30]=656 Freq[31]=656 Freq[32]=656 Freq[33]=656 Freq[34]=656 Freq[35]=656
Freq[36]=656 Freq[37]=656 Freq[38]=656 Freq[39]=656 Freq[40]=656 Freq[41]=656 Freq[42]=656
Freq[43]=656 Freq[44]=656 Freq[45]=656 Freq[46]=656 Freq[47]=656 Freq[48]=656 Freq[49]=656
Freq[50]=656 Freq[51]=656 Freq[52]=656 Freq[53]=656 Freq[54]=656 Freq[55]=656 Freq[56]=656
Freq[57]=656 Freq[58]=656 Freq[59]=656 Freq[60]=656 Freq[61]=656 Freq[62]=656
Chain[7] bad core info:
ASIC[0] bad core num=1
ASIC[3] bad core num=1
ASIC[6] bad core num=1
ASIC[8] bad core num=1
ASIC[9] bad core num=1
ASIC[11] bad core num=1
ASIC[12] bad core num=1
ASIC[14] bad core num=1
ASIC[15] bad core num=1
ASIC[17] bad core num=1
ASIC[18] bad core num=1
ASIC[20] bad core num=1
ASIC[21] bad core num=1
ASIC[23] bad core num=1
ASIC[24] bad core num=1
ASIC[27] bad core num=1
ASIC[31] bad core num=1
ASIC[32] bad core num=1
ASIC[34] bad core num=1
ASIC[35] bad core num=1
ASIC[37] bad core num=1
ASIC[38] bad core num=2
ASIC[40] bad core num=1
ASIC[43] bad core num=1
ASIC[46] bad core num=1
ASIC[49] bad core num=1
ASIC[52] bad core num=1
ASIC[55] bad core num=2
ASIC[56] bad core num=1
ASIC[59] bad core num=1
ASIC[62] bad core num=2
After TEST CRC error counter=0
check FAN Speed: fan[2] speed=5880
check FAN Speed: fan[5] speed=5400
check FAN OK: fan num=2
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 2 times, completed chain = 1, total chain num = 3
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL
--- check asic number
check chain[5]: asicNum = 63
check chain[6]: asicNum = 63
After Get ASIC NUM CRC error counter=0
set_baud=0
SEARCH_FREQ_TEST_UPONESTEP mode set freq=637 voltage=890 on chain[5]
SEARCH_FREQ_TEST_LEVEL mode set freq=606 voltage=910 on chain[6]
The min freq=606
set real timeout 60, need sleep=437760
start send works on chain[5]
start send works on chain[6]
get send work num :57456 on Chain[5]
get send work num :57456 on Chain[6]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=637 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=637 freq[36]=637 freq[37]=637 freq[38]=637 freq[39]=637
freq[40]=637 freq[41]=637 freq[42]=637 freq[43]=637 freq[44]=637 freq[45]=637 freq[46]=637 freq[47]=637
freq[48]=637 freq[49]=637 freq[50]=637 freq[51]=637 freq[52]=637 freq[53]=637 freq[54]=637 freq[55]=637
freq[56]=637 freq[57]=637 freq[58]=637 freq[59]=637 freq[60]=637 freq[61]=637 freq[62]=637
total valid nonce number:57260
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:13630
last_nonce_num:2228
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
freq[00]=606 freq[01]=606 freq[02]=606 freq[03]=606 freq[04]=606 freq[05]=606 freq[06]=606 freq[07]=606
freq[08]=606 freq[09]=606 freq[10]=606 freq[11]=606 freq[12]=606 freq[13]=606 freq[14]=606 freq[15]=606
freq[16]=606 freq[17]=606 freq[18]=606 freq[19]=606 freq[20]=606 freq[21]=606 freq[22]=606 freq[23]=606
freq[24]=606 freq[25]=606 freq[26]=606 freq[27]=606 freq[28]=606 freq[29]=606 freq[30]=606 freq[31]=606
freq[32]=606 freq[33]=606 freq[34]=606 freq[35]=606 freq[36]=606 freq[37]=606 freq[38]=606 freq[39]=606
freq[40]=606 freq[41]=606 freq[42]=606 freq[43]=606 freq[44]=606 freq[45]=606 freq[46]=606 freq[47]=606
freq[48]=606 freq[49]=606 freq[50]=606 freq[51]=606 freq[52]=606 freq[53]=606 freq[54]=606 freq[55]=606
freq[56]=606 freq[57]=606 freq[58]=606 freq[59]=606 freq[60]=606 freq[61]=606 freq[62]=606
total valid nonce number:0
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:0
last_nonce_num:0
checkBoardState chain[5] rate=4541 bad_chip_num=0 lowest rate=4500 ret=2
SEARCH_FREQ_TEST_UPONESTEP get BOARD_FREQ_OK on chain[5]
special fix hash_voltage pic value = 91 [890] of Chain[5], voladded=0
Write freq to PIC :
Freq[00]=637
Freq[01]=637 Freq[02]=637 Freq[03]=637 Freq[04]=637 Freq[05]=637 Freq[06]=637 Freq[07]=637
Freq[08]=637 Freq[09]=637 Freq[10]=637 Freq[11]=637 Freq[12]=637 Freq[13]=637 Freq[14]=637
Freq[15]=637 Freq[16]=637 Freq[17]=637 Freq[18]=637 Freq[19]=637 Freq[20]=637 Freq[21]=637
Freq[22]=637 Freq[23]=637 Freq[24]=637 Freq[25]=637 Freq[26]=637 Freq[27]=637 Freq[28]=637
Freq[29]=637 Freq[30]=637 Freq[31]=637 Freq[32]=637 Freq[33]=637 Freq[34]=637 Freq[35]=637
Freq[36]=637 Freq[37]=637 Freq[38]=637 Freq[39]=637 Freq[40]=637 Freq[41]=637 Freq[42]=637
Freq[43]=637 Freq[44]=637 Freq[45]=637 Freq[46]=637 Freq[47]=637 Freq[48]=637 Freq[49]=637
Freq[50]=637 Freq[51]=637 Freq[52]=637 Freq[53]=637 Freq[54]=637 Freq[55]=637 Freq[56]=637
Freq[57]=637 Freq[58]=637 Freq[59]=637 Freq[60]=637 Freq[61]=637 Freq[62]=637
Chain[5] bad core info:
ASIC[0] bad core num=1
ASIC[3] bad core num=1
ASIC[6] bad core num=1
ASIC[7] bad core num=1
ASIC[8] bad core num=1
ASIC[9] bad core num=1
ASIC[10] bad core num=1
ASIC[11] bad core num=1
ASIC[12] bad core num=1
ASIC[13] bad core num=2
ASIC[14] bad core num=1
ASIC[15] bad core num=1
ASIC[16] bad core num=1
ASIC[18] bad core num=2
ASIC[19] bad core num=1
ASIC[20] bad core num=3
ASIC[21] bad core num=1
ASIC[22] bad core num=1
ASIC[23] bad core num=1
ASIC[24] bad core num=1
ASIC[27] bad core num=1
ASIC[32] bad core num=1
ASIC[34] bad core num=1
ASIC[35] bad core num=1
ASIC[36] bad core num=1
ASIC[37] bad core num=1
ASIC[38] bad core num=2
ASIC[39] bad core num=2
ASIC[40] bad core num=1
ASIC[41] bad core num=1
ASIC[42] bad core num=1
ASIC[43] bad core num=1
ASIC[44] bad core num=1
ASIC[45] bad core num=1
ASIC[46] bad core num=1
ASIC[47] bad core num=2
ASIC[49] bad core num=1
ASIC[50] bad core num=2
ASIC[51] bad core num=1
ASIC[52] bad core num=1
ASIC[53] bad core num=2
ASIC[55] bad core num=1
ASIC[59] bad core num=1
ASIC[62] bad core num=1
checkBoardState chain[6] rate=0 bad_chip_num=63 lowest rate=4333 ret=1
After TEST CRC error counter=0
check FAN Speed: fan[2] speed=5880
check FAN Speed: fan[5] speed=5400
check FAN OK: fan num=2
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 3 times, completed chain = 2, total chain num = 3
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL
--- check asic number
check chain[6]: asicNum = 63
After Get ASIC NUM CRC error counter=0
set_baud=0
SEARCH_FREQ_TEST_LEVEL mode set freq=581 voltage=920 on chain[6]
The min freq=581
set real timeout 63, need sleep=459648
start send works on chain[6]
get send work num :57456 on Chain[6]
wait recv nonce on chain[6]
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
freq[00]=581 freq[01]=581 freq[02]=581 freq[03]=581 freq[04]=581 freq[05]=581 freq[06]=581 freq[07]=581
freq[08]=581 freq[09]=581 freq[10]=581 freq[11]=581 freq[12]=581 freq[13]=581 freq[14]=581 freq[15]=581
freq[16]=581 freq[17]=581 freq[18]=581 freq[19]=581 freq[20]=581 freq[21]=581 freq[22]=581 freq[23]=581
freq[24]=581 freq[25]=581 freq[26]=581 freq[27]=581 freq[28]=581 freq[29]=581 freq[30]=581 freq[31]=581
freq[32]=581 freq[33]=581 freq[34]=581 freq[35]=581 freq[36]=581 freq[37]=581 freq[38]=581 freq[39]=581
freq[40]=581 freq[41]=581 freq[42]=581 freq[43]=581 freq[44]=581 freq[45]=581 freq[46]=581 freq[47]=581
freq[48]=581 freq[49]=581 freq[50]=581 freq[51]=581 freq[52]=581 freq[53]=581 freq[54]=581 freq[55]=581
freq[56]=581 freq[57]=581 freq[58]=581 freq[59]=581 freq[60]=581 freq[61]=581 freq[62]=581
total valid nonce number:0
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:0
last_nonce_num:0
checkBoardState chain[6] rate=0 bad_chip_num=63 lowest rate=4166 ret=1
After TEST CRC error counter=0
check FAN Speed: fan[2] speed=5880
check FAN Speed: fan[5] speed=5400
check FAN OK: fan num=2
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 4 times, completed chain = 2, total chain num = 3
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL
--- check asic number
check chain[6]: asicNum = 63
After Get ASIC NUM CRC error counter=0
set_baud=0
SEARCH_FREQ_TEST_LEVEL mode set freq=562 voltage=940 on chain[6]
The min freq=562
set real timeout 65, need sleep=474240
start send works on chain[6]
get send work num :57456 on Chain[6]
wait recv nonce on chain[6]
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
freq[00]=562 freq[01]=562 freq[02]=562 freq[03]=562 freq[04]=562 freq[05]=562 freq[06]=562 freq[07]=562
freq[08]=562 freq[09]=562 freq[10]=562 freq[11]=562 freq[12]=562 freq[13]=562 freq[14]=562 freq[15]=562
freq[16]=562 freq[17]=562 freq[18]=562 freq[19]=562 freq[20]=562 freq[21]=562 freq[22]=562 freq[23]=562
freq[24]=562 freq[25]=562 freq[26]=562 freq[27]=562 freq[28]=562 freq[29]=562 freq[30]=562 freq[31]=562
freq[32]=562 freq[33]=562 freq[34]=562 freq[35]=562 freq[36]=562 freq[37]=562 freq[38]=562 freq[39]=562
freq[40]=562 freq[41]=562 freq[42]=562 freq[43]=562 freq[44]=562 freq[45]=562 freq[46]=562 freq[47]=562
freq[48]=562 freq[49]=562 freq[50]=562 freq[51]=562 freq[52]=562 freq[53]=562 freq[54]=562 freq[55]=562
freq[56]=562 freq[57]=562 freq[58]=562 freq[59]=562 freq[60]=562 freq[61]=562 freq[62]=562
total valid nonce number:0
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:0
last_nonce_num:0
checkBoardState chain[6] rate=0 bad_chip_num=63 lowest rate=4000 ret=1
SEARCH_FREQ_TEST_LEVEL level=7 on chain[6], Error: no highest rate record!
I would be very thankfull for any advice, since half of my antminer purchase is not working as it should. Best regards
I have the following problem:
Any suggestions?
upgrade to most updated firmware, if it doesn't work, try to power off, wait 15 minutes, then power on, maybe several times.
Hello
I have a problem with S9 - it seems to be working but there's no accepted shares. I described problem in detail here - https://support.bitmain.com/hc/en-us/requests/376825
Maybe someone had similar problem and know where to look? It seems that hardware is ok, but there's some software problem. I've already tried to fix it in repair shop and they did, but after 1.5 days of work it doesn't accept shares again.
If someone had similar issue please give me a hint what do I need to fix?
Thank you Grand,
Firmware upgrade worked for me. Now in the kernel log I can see that it can find all the asics.
But now in the overview, the hardware version and BMminer Version are blank. And In miner status no boards appear.
edit:
In ordered to work I had to downgrade to the previous firmware (20170428) and restart several times (it didn't work the first time). Using the new firmware there was a problem with the fans.
However, all these solutions do not seem proper to me. Is there any definite solution to the problem?
I have a problem with the brand new A3 miner. The fans power on, but there is no green nor red light, there is no IP, reset button doesn't work...I cannot do anything with it...is it a control panel malfunction or what? I tried everything including flashing via SD card and nothing helped. Help anyone who can
Hello
Thx
Contact Barbara (Bitmain) <support@bitmainhelp.zendesk.com>
She is so helpful.
Hi everyone,
I have one PSU of following specifications, so to what Antminer it could be used!
Sorcerer Power Supply Unit Input 176 264V AC 15A MAX 50/60Hz 1600W 8 X 6-PIN
Thanks so much
Article is closed for comments.